Commit f7d190b1 corrected the value of MPC85xx_PORDEVSR2_SEC_CFG, but forgot
to add a comment that the correct value disagrees with the 8544 reference
manual. The changelog for that commit is also wrong, as it says "bit 28"
when it should be "bit 24".
Signed-off-by: Timur Tabi <timur@freescale.com>
The pixis sgmii command depend on the FPGA support on the board, some 85xx
boards support SGMII riser card but did not support this command, define
CONFIG_PIXIS_SGMII_CMD for those boards which support the sgmii command.
Not like 8544, 8572 has 4 eTsec so that the other two's pixis bits
are not supported by 8544. Therefor, define PIXIS_VSPEED2_MASK and
PIXIS_VCFGEN1_MASK in header file for both boards.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay, 2T based on board ddr frequency and n_ranks.
* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.
* Set memory controller interleaving mode to bank interleaving, and disable
bank(chip select) interleaving mode by default, because the default on-board
DDR DIMMs are 2x512MB single-rank.
* Change CONFIG_ICS307_REFCLK_HZ from 33333333 to 33333000.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Because some dimm parameters like n_ranks needs to be used with the board
frequency to choose the board parameters like clk_adjust etc. in the
board_specific_paramesters table of the board ddr file, we need to pass
the dimm parameters to the board file.
* move ddr dimm parameters header file from /cpu to /include directory.
* add ddr dimm parameters to populate board specific options.
* Fix fsl_ddr_board_options() for all the 8xxx boards which call this function.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Fix some bugs:
1. Correctly set intlv_ctl in cs_config.
2. Correctly set sa, ea in cs_bnds when bank interleaving mode is enabled.
3. Set base_address and total memory for each ddr controller in memory
controller interleaving mode.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Added the ability for C code to invalidate the i/d-cache's and
to flush the d-cache. This allows us to more efficient change mappings
from cache-able to cache-inhibited.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Sub-command can benefit from using the same table and search functions
that top level commands have. Expose this functionality by refactoring
find_cmd() and introducing find_cmd_tbl() that sub-command processing
can call.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The EEprom contains some Manufacturerinformation,
which are read from u-boot at boot time, and saved
in same hush shell variables.
Signed-off-by: Heiko Schocher <hs@denx.de>
This new command shows the local variables defined in
the hush shell:
=> help showvar
showvar
- print values of all hushshell variables
showvar name ...
- print value of hushshell variable 'name'
Also make the set_local_var() and unset_local_var ()
no longer static, so it is possible to define local
hush shell variables at boot time. If CONFIG_HUSH_INIT_VAR
is defined, u-boot calls hush_init_var (), where
boardspecific code can define local hush shell
variables at boottime.
Signed-off-by: Heiko Schocher <hs@denx.de>
With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.
Signed-off-by: Heiko Schocher <hs@denx.de>
As documented in doc/I2C_Edge_Conditions, adding a
board specific deblocking mechanism via CFG_I2C_INIT_BOARD
for the mgcoge and mgsuvd board.
This code was originally written by Keymile in association
with Anatech and Atmel in 1998. The Code toggels the SCL
until the SCA line goes to HIGH (max. 16 times).
And after this, a start condition is sent.
This is another approach to deblock the I2C Bus. The
soft I2C driver actually sends 9 clocks with SDA High,
and then a stop at the end, to deblock the I2C Bus.
Maybe we should use the approach from Keymile as
the new standard?
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch fixes the following warnings, when using
the soft_i2c driver using no CPU pins on MPC82xx or MPC8xx
systems:
soft_i2c.c: In function 'send_reset':
soft_i2c.c:93: warning: unused variable 'immr'
soft_i2c.c: In function 'send_start':
soft_i2c.c:124: warning: unused variable 'immr'
soft_i2c.c: In function 'send_stop':
soft_i2c.c:146: warning: unused variable 'immr'
soft_i2c.c: In function 'send_ack':
soft_i2c.c:171: warning: unused variable 'immr'
soft_i2c.c: In function 'write_byte':
soft_i2c.c:196: warning: unused variable 'immr'
soft_i2c.c: In function 'read_byte':
soft_i2c.c:244: warning: unused variable 'immr'
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds support for the National LM63 temperature
sensor with integrated fan control. It's used on the GDSys
Neo board (405EP) which will be submitted later.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Acked-by: Stefan Roese <sr@denx.de>
Now it's used at UBI module. Of course other modules can use it.
If you want to use it, please define CONFIG_RBTREE
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The GUID (Globally Unique Identifier) Partition Table (GPT) is a part
of EFI. See http://en.wikipedia.org/wiki/GUID_Partition_Table
Based on linux/fs/partitions/efi.[ch]
Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>
The upcoming automatic update feature needs the ability to adjust an
address within Flash to the end of its respective sector. Factor out
this functionality to a new function flash_sect_roundb().
Signed-off-by: Rafal Czubak <rcz@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added as a convenience for other platforms that uses MPC8360 (has 8 UCC).
Six eth interface is chosen because the platform I am using combines
UCC1&2 and UCC3&4 as 1000 Eth and the other four UCCs as 10/100 Eth.
Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Change UEC phy interface from GMII to RGMII on MPC8568MDS board
Because on MPC8568MDS, GMII interface is only recommended for 1000Mbps speed,
but RGMII interface can work at 10/100/1000Mbps, and RGMII interface works more stable.
Now both UEC1 and UEC2 can work properly under u-boot.
It is also in consistent with the kernel setting for 8568 UEC phy interface.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Set the MQ Read Passing & MCIF Cycle limits to the recommended by AMCC
values. This fixes the occasional 440SPe hard locking issues when the 440SPe's
dedicated DMA engines are used (e.g. by the h/w accelerated RAID driver).
Previously the appropriate initialization had been made in Linux, by the
ppc440spe ADMA driver, which is wrong because modifying the MQ configuration
registers after normal operation has begun is not supported and could
have unpredictable results.
Comment from Stefan: This patch doesn't change the resulting value of the
MQ registers. It explicitly sets/clears all bits to the desired state which
better documents the resulting register value instead of relying on pre-set
default values.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The MPC8544 RM incorrect shows the SEC_CFG bit in PORDEVSR2 as being
bit 26, instead it should be bit 28. This caused in incorrect
interpretation of the i2c_clk which is the same as the SEC clk on
MPC8544. The SEC clk is controlled by cfg_sec_freq that is reported
in PORDEVSR2.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently this is not creating any problem. But it will result
in compilation error when used as below.
printf("CFG_SDRAM_CFG2 - %08x\n", CFG_SDRAM_CFG2);
Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
continuation of the theme based on git grep "^#define CFG_.*;$" include/
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The max packet size is encoded as 0,1,2,3 for 8,16,32,64 bytes.
At some places directly 8,16,32,64 was used instead of the encoded
value. Made a enum for the options to make this more clear and to help
preventing similar errors in the future.
After fixing this bug it became clear that another bug existed where
the 'pipe' is and-ed with PIPE_* flags, where it should have been
'usb_pipetype(pipe)', or even better usb_pipeint(pipe).
Also removed the triple 'get_device_descriptor' sequence, it has no use,
and Windows nor Linux behaves that way.
There is also a poll going on with a timeout when usb_control_msg() fails.
However, the poll is useless, because the flag will never be set on a error,
because there is no code that runs in a parallel that can set this flag.
Changed this to something more logical.
Tested on AT91SAM9261ek and compared the flow on the USB bus to what
Linux is doing. There is no difference anymore in the early initialisation
sequence.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Commit 445a7b3830 introduced the following
compile warnings:
cmd_i2c.c:112: warning: missing braces around initializer
cmd_i2c.c:112: warning: (near initialization for 'i2c_no_probes[0]')
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Switch to the standard CFG_HZ=1000 value, while at it, minor white-space
cleanup, remove CFG_CLKS_IN_HZ from config-headers. Tested on mx31ads,
provides 2% or 0.4% precision depending on the
CONFIG_MX31_TIMER_HIGH_PRECISION flag. Measured with stop-watch on 100s
boot-delay.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
The ID EEPROM on MPC8572DS board locates on I2C bus 1. Its the storage for
system information like mac addresses etc. This patch enables it.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
MPC8572DS has two i2c buses. This patch moves the DDR SPD_EEPROM to i2c bus 1
according to the board spec, and adds the 2nd i2c bus offset.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
On 8536DS board, When the DDR clk is set async mode(SW3[6:8] != 111),
The display is still sync mode DDR freq. This patch try to fix
this. The display DDR freq is now the actual freq in both
sync and async mode.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Oops, screwed up the function name in the documenting comment for this
function. Trivial correction in this patch.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Kumar has already added alias expansion to fdt_path_offset().
However, in some circumstances it may be convenient for the user of
libfdt to explicitly get the string expansion of an alias. This patch
adds a function to do this, fdt_get_alias(), and uses it to implement
fdt_path_offset().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Using Gcc 4.3 detected this problem:
../dtc/libfdt/fdt.c: In function 'fdt_next_tag':
../dtc/libfdt/fdt.c:82: error: assuming signed overflow does not
occur when assuming that (X + c) < X is always false
To fix the problem, treat the offset as an unsigned int.
The problem report and proposed fix were provided
by Steve Papacharalambous <stevep@freescale.com>.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
bootdelay set to -1 'permanently' disables autobooting, even if
bootcmd is specified. Change to a positive value to allow
autobooting when a bootcmd is set.
Reported-by: Coray Tate <Coray.Tate@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Fixed typo from CONIFG_MPC837X to CONFIG_MPC837X
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
the operating system may leave flash in a h/w locked state after writing.
This allows u-boot to continue to write flash by enabling h/w unlocking
by default.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
A few Spartan-3 definitions erroneously use Spartan-3E size
constants. This patch fixes them.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Running mtest command on socrates without specifying
an address range crashes the board. This patch changes
default mtest address range to prevent this behavior.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Commit be0bd8234b
changed SPD EEPROM address to 0x51 and DDR SDRAM
detection stopped working. Change this address
back to 0x50.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
After switching to using the CFI flash driver, the correct remapping
of the flash banks was forgotten.
Also, some boards were not adapted, and the old legacy flash driver
was not removed yet.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 2a1a2cb6 didnt remove the dummy mem reservation in fdt_chosen,
and this stopped Linux from booting with a Ramdisk. This patch fixes
this, by deleting the useless dummy mem reservation.
When booting with a Ramdisk, a fix offset FDT_RAMDISK_OVERHEAD is now
added to of_size, so we dont need anymore a dummy mem reservation.
I measured the value of FDT_RAMDISK_OVERHEAD on a MPC8270 based
system (=0x44 bytes) and rounded it up to 0x80).
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes a problem introdiced with patch
bbeff30c [ppc4xx: Remove superfluous dram_init() call or replace it by
initdram()].
The boards affected are:
- PCI405
- PPChameleonEVB
- quad100hd
- taihu
- zeus
Signed-off-by: Stefan Roese <sr@denx.de>
- Correct Invalid #define of MPUTIM_PTV_MASK for
omap1510 & omap730 register definition
MPUTIM_PTV_MASK is defined as
#define MPUTIM_PTV_MASK (0x7<<PTV_BIT)
while it should have been
#define MPUTIM_PTV_MASK (0x7<<MPUTIM_PTV_BIT)
- Below Patch corrects the same
Signed-off-by: Gururaja Hebbar <gururajakr@sanyo.co.in>
The i.MX31 has three SPI buses and each bus has several chip selects
and the MC13783 chip can be connected to any of these. The current
RTC driver for MC13783 is hardcoded for CSPI2/SS2.
This patch makes make MC13783 SPI bus and chip select configurable
via CONFIG_MC13783_SPI_BUS and CONFIG_MC13783_SPI_CS.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
- add function fit_all_image_check_hashes() that verifies if all
hashes of all images in the FIT are valid
- improve output of fit_image_check_hashes() when the hash check fails
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Pantelis Antoniou stated:
AFAIK, it is still used but the products using PPC are long gone.
Nuke it plz (from orbit).
So remove it since it cleans up a usage of env_get_char outside of
the environment code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds Lime GDC support together with support for the PWM
backlight control through the w83782d chip. The reset pin of the
latter is attached to GPIO, so we need to reset it in
early_board_init_r.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
- Update the local bus ranges in the FDT for Linux for the various
devices connected to the local bus via chip-select.
- Set the LCRR_DBYP bit in the LCRR for local bus frequencies
lower than 66 MHz and uses I/O accessor functions consequently.
- UPM data update.
- Update of default environment and configuration. Use I2C multibus
as we do have two I2C buses. Also enable sdram and ext2 commands.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Detlev Zundel <dzu@denx.de>
The new sys_eeprom.c supports both the old CCID EEPROM format and the new NXID
format, and so it obsoletes board/freescale/common/cds_eeprom.c. Freescale
86xx boards already use sys_eeprom.c, so this patch migrates the remaining
Freescale 85xx boards to use it as well. cds_eeprom.c is deleted.
Signed-off-by: Timur Tabi <timur@freescale.com>
This patch add FDT support and command line editing capabilities
for CPCI405 and CPCI405AB boards.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Since this define is only used on one board that was never really in
production, removing this compile time option doesn't hurt and makes
the code more readable.
Signed-off-by: Stefan Roese <sr@denx.de>
Added new CONFIG_DISABLE_CONSOLE define and GD_FLG_DISABLE_CONSOLE.
When CONFIG_DISABLE_CONSOLE is defined, setting
GD_FLG_DISABLE_CONSOLE disables all console input and output.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Some of multi-function USB controllers (e.g. ISP1562) allow root hub
resetting only via EHCI registers. So, this patch adds the
corresponding kind of reset to OHCI's hc_reset() if the newly
introduced CONFIG_PCI_EHCI_DEVNO option is set (e.g. for Socrates
board).
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Acked-by: Markus Klotzbuecher <mk@denx.de>
This patch adds GPCS, SGMII and M88E1112 PHY support
for the AMCC PPC460GT/EX processors.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch provides an unificated way of handling xilinx v5 ppc440 boards.
It unificates 3 different things:
1) Source code
A new board called ppc440-generic has been created. This board includes
a generic tlb initialization (Maps the whole memory into virtual) and
defines board_pre_init, checkboard, initdram and get_sys_info weakly,
so, they can be replaced by specific functions.
If a new board needs to redefine any of the previous functions
(specific initialization) it can create a new directory with the
specific initializations needed. (see the example ml507 board).
2) Configuration file
Common configurations are located under configs/xilinx-ppc440.h, this
header file interpretes the xparameters file generated by EDK and
configurates u-boot in correspondence. Example: if there is a Temac,
allows CMD_CONFIG_NET
Specific configuration are located under specific configuration file.
(see the example ml507 board)
3) Makefile
Some work has been done in order to not duplicate work in the Main
Makefile. Please see the attached code.
In order to support new boards they can be implemented in the next way:
a) Simple Generic Board (90% of the time)
Using EDK generates a new xparameters.h file, replace
ppc440-generic/xparameters.h and run make xilinx-ppc440-generic_config
&& make
b) Simple Boards with special u-boot parameters (9 % of the time)
Create a new file under configs for it (use ml507.h as example) and
change your paramaters. Create a new Makefile paragraph and compile
c) Complex boards (1% of the time)
Create a new folder for the board, like the ml507
Finally, it adds support for the Avnet FX30T Evaluation board, following
the new generic structure:
Cheap board by Avnet for evaluating the Virtex5 FX technology.
This patch adds support for:
- UartLite
- 16MB Flash
- 64MB RAM
Prior using U-boot in this board, read carefully the ERRATA by Avnet
to solve some memory initialization issues.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
Record the Arbiter Event Register values and optionally display them.
The Arbiter Event Register can record the type and effective address of
an arbiter error, even through an HRESET. This patch stores the values in
the global data structure.
Display of the Arbiter Event registers immediately after the RSR value
can be enabled with defines. The Arbiter values will only be displayed
if an arbiter event has occured since the last Power On Reset, and either
of the following defines exist:
#define CONFIG_DISPLAY_AER_BRIEF - display only the arbiter address and
and type register values
#define CONFIG_DISPLAY_AER_FULL - display and interpret the arbiter
event register values
Address Only transactions are one of the trapped events that can register
as an arbiter event. They occur with some cache manipulation instructions
if the HID0_ABE (Address Broadcast Enable) is set and the memory region
has the MEMORY_COHERENCE WIMG bit set. Setting:
#define CONFIG_MASK_AER_AO - prevents the arbiter from recording address
only events, so that it can still capture
other real problems.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch enables the PCI-OHCI controller on PLU405 board.
Also the default CPU frequency is updated to 266 MHz and
command line editing is enabled.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Modified board_eth_init() functions of boards that have this FEC in addition
to other Ethernet controllers.
Affected boards:
bc3450
icecube
mvbc_p
o2dnt
pm520
total5200
tq5200
Removed initialization of controller from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Affected boards:
hidden_dragon
MPC8544DS
MPC8610HPCN
R2DPLUS
TB0229
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8544DS and 8572DS platforms support an optional SGMII riser card to
expose ethernet over an SGMII interface. Once the card is in, it is also
necessary to configure the board such that it uses the card, rather than
the on-board ethernet ports. This can either be done by flipping dip switches
on the motherboard, or by modifying registers in the pixis. Either way
requires a reboot.
This adds a command to allow users to choose which ports are routed through
the SGMII card, and which through the onboard ports. It also allows users
to revert to the current switch settings.
This code does not work on the 8572, as the PIXIS is different.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8544DS and 8572DS systems have an optional SGMII riser card which
exposes new ethernet ports which are connected to the eTSECs via an
SGMII interface. The SGMII PHYs for this board are offset from the standard
PHY addresses, so this code modifies the passed in tsec_info structure to
use the SGMII PHYs on the card, instead.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Adds support for configuring the TBI to talk properly with the SerDes.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The tsec driver contains a hard-coded array of configuration information
for the tsec ethernet controllers. We create a default function that works
for most tsecs, and allow that to be overridden by board code. It creates
an array of tsec_info structures, which are then parsed by the corresponding
driver instance to determine configuration. Also, add regs, miiregs, and
devname fields to the tsec_info structure, so that we don't need the kludgy
"index" parameter.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This is to prepare the way for board code passing in the tsec_info structure
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This is expected by the callers, but this fact was hidden well within
the old list implementation.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This boards used old type preprocessor.
This patch fix compile error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This boards used old type preprocessor.
This patch fix compile error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
AP325RXA is SH7723's reference board.
This has SCIF, NOR Flash, Ethernet, USB host, LCDC, SD Host, Camera and other.
In this patch, support SCIF, NOR Flash, and Ethernet.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Renesas SH7723 has 5 SCIF, SD, Camera, LCDC and other.
This patch supports CPU register's header file and SCIF serial driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds initial support for the RTE RSK+ SH7203 board.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This board has SH7785, 512MB DDR2-SDRAM, NOR Flash,
Graphic, Ethernet, USB, SD, RTC, and I2C controller.
This patch supports the following functions:
- 128MB DDR2-SDRAM (29-bit address mode only)
- NOR Flash
- USB host
- Ethernet
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SMDK6400 can only boot U-Boot from NAND-flash. This patch adds a nand_spl
driver for it too. The board can also boot from the NOR flash, but due to
hardware limitations it can only address 64KiB on it, which is not enough
for U-Boot. Based on the original sources by Samsung for U-Boot 1.1.6.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This is needed since now with HUSH enabled (amcc-common.h) the image
read from NAND exceeds the previous limit.
Signed-off-by: Stefan Roese <sr@denx.de>
MPC5121 rev 2 silicon has a new register for controlling how long
CS is asserted after deassertion of ALE in multiplexed mode.
The default is to assert CS together with ALE. The alternative
is to assert CS (ALEN+1)*LPC_CLK clocks after deassertion of ALE.
The default is wrong for the NOR flash and CPLD on the ADS5121.
This patch turns on the alternative for CS0 (NOR) and CS2 (CPLD)
it does so conditionally based on silicon rev 2.0 or greater.
Signed-off-by: Martha J Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
Add FEC pin set and mii reset in __mii_init(). Change
legacy flash vendor from 2 to AMD LEGACY (0xFFF0),
change cfi_offset to 0, and change CFG_FLASH_CFI to
CONFIG_FLASH_CFI_LEGACY. Correct M54451EVB and
M54455EVB env settings in configuration file.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8536 Adds SDHC and SATA controllers to the PQ3 family. We
also have SERDES init code for the 8536.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
The main purpose of this rewrite it to be able to share the same
initialization code on all FSL PowerPC products that have DDR
controllers. (83xx, 85xx, 86xx).
The code is broken up into the following steps:
GET_SPD
COMPUTE_DIMM_PARMS
COMPUTE_COMMON_PARMS
GATHER_OPTS
ASSIGN_ADDRESSES
COMPUTE_REGS
PROGRAM_REGS
This allows us to share more code an easily allow for board specific code
overrides.
Additionally this code base adds support for >4G of DDR and provides a
foundation for supporting interleaving on processors with more than one
controller.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Provide a helper function that will setup the last available
LAWs (upto 2) for DDR. Useful for SPD/dyanmic DDR setting code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Created a new fdt_initrd() to deal with setting the initrd properties
in the device tree and fixing up the mem reserve. We can use this
both in the choosen node handling and lets us remove some duplicated
code when we fixup the initrd info in bootm on PPC.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Created a bootm_start() that handles the parsing and detection of all
the images that will be used by the bootm command (OS, ramdisk, fdt).
As part of this we now tract all the relevant image offsets in the
bootm_headers_t struct. This will allow us to have all the needed
state for future sub-commands and lets us reduce a bit of arch
specific code on SPARC.
Created a bootm_load_os() that deals with decompression and loading
the OS image.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To allow for persistent state between future bootm subcommands we
need the lmb to exist in a global state.
Moving it into the bootm_headers_t allows us to do that.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Set the fdt working address so "fdt FOO" commands can be used as part
of the bootm flow. Also set an the environment variable "fdtaddr"
with the value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move the code that handles finding a device tree blob and relocating
it (if needed) into common code so all arch's have access to it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move determing if we have a ramdisk and where its located into the
common code. Keep track of the ramdisk start and end in the
bootm_headers_t image struct.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move entry point code out of each arch and into common code.
Keep the entry point in the bootm_headers_t images struct.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fix mvBL-M7 config and move to matrix_vision subdir
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds elements to the 83xx sysconf structure and #define values that are used
by mpc83xx family devices.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add the ability for the MPC8349EMDS to run in PCI Agent mode, acting as a
PCI card rather than a host computer.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Change the MPC8349EMDS board to use the generic PCI initialization code
for the mpc83xx cpu.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
As well as fdt_subnode_offset(), libfdt includes an
fdt_subnode_offset_namelen() function that takes the subnode name to
look up not as a NUL-terminated string, but as a string with an
explicit length. This can be useful when the caller has the name as
part of a longer string, such as a full path.
However, we don't have corresponding 'namelen' versions for
fdt_get_property() and fdt_getprop(). There are less obvious use
cases for these variants on property names, but there are
circumstances where they can be useful e.g. looking up property names
which need to be parsed from a longer string buffer such as user input
or a configuration file, or looking up an alias in a path with
IEEE1275 style aliases.
So, since it's very easy to implement such variants, this patch does
so. The original NUL-terminated variants are, of course, implemented
in terms of the namelen versions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Enabling -Wcast-qual warnings in dtc shows up a number of places where
we are incorrectly discarding a const qualification. There are also
some places where we are intentionally discarding the 'const', and we
need an ugly cast through uintptr_t to suppress the warning. However,
most of these are pretty well isolated with the *_w() functions. So
in the interests of maximum safety with const qualifications, this
patch enables the warnings and fixes the existing complaints.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
This patch turns on the -Wpointer-arith option in the dtc Makefile,
and fixes the resulting warnings due to using (void *) in pointer
arithmetic. While convenient, pointer arithmetic on void * is not
portable, so it's better that we avoid it, particularly in libfdt.
Also add necessary definition of uintptr_t needed by David Gibson's
changeset "dtc: Enable and fix -Wpointer-arith warnings" (the definition
comes from stdint.h, which u-boot doesn't have). -- gvb
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
This patch fixes some minor issues introduced with the patch:
ppc4xx: Optimize PLB4 Arbiter... from Prodyut Hazarika:
- Rework memory-queue and PLB arbiter optimization code, that the
local variable is not needed anymore. This removes one #ifdef.
- Use consistant spacing in ppc4xx.h header (XXX + 0x01 instead
of XXX+ 0x01). This was not introduced by Prodyut, just a
copy-paste problem.
Signed-off-by: Stefan Roese <sr@denx.de>
PPC405EX and PPC460EX/GT/SX
- Read pipeline depth set to 4 for PPC440SP/SPE, PPC405EX, PPC460EX/GT/SX
processors
- Moved PLB4 Arbiter register definitions to ppc4xx.h since it is shared
across processors (405 and 440/460)
- Optimize Memory Queue settings for PPC440SP/SPE and PPC460EX/GT/SX
processors
- Add register bit definitions for Memory Queue Configuration registers
Signed-off-by: Prodyut Hazarika <phazarika@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Move to using the environment variables 'ethaddr', 'eth1addr', etc..
instead of bd->bi_enetaddr, bi_enet1addr, etc.
This makes the code a bit more flexible to the number of ethernet
interfaces.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
ARM, i386, m68k and ppc all have identical implementations of strmhz().
Other architectures don't provide this function at all.
This patch moves strmhz() into lib_generic, reducing code duplication
and providing a more unified API across architectures.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds a hook whereby a board-specific routine can be called to
configure hardware for a PIO mode. The prototype for the board-specific
routine is:
int inline ide_set_piomode(int pio_mode)
ide_set_piomode should be prepared to configure hardware for a pio_mode
between 0 and 6, inclusive. It should return 0 on success or 1 on failure.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
This patch removes some enums from ata.h and replaces them with an
include of libata.h. This way, we eliminate duplicated code, and
prevent errors whereby the different versions could be out of sync.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
The MIMC200 board is based on Atmel's NGW100 dev kit, but with an extra
8MByte FLASH and 128KByte FRAM.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
