Use DM for the pl01x serial driver on hikey. Also allow UART0 or
UART3 to be chosen via Kconfig.
By default we now output to UART3 as the latest version of ATF outputs
to this UART. Also UART3 comes out on the LS connector, as opposed to
UART0 which goes to a unpopulated header.
As part of this change we also enable CONFIG_BOARD_EARLY_INIT_F and
call the pinmux configuration code for the UART. Before we were
relying on ATF having already configured the pin configuration.
NB: Upstream Linux kernel doesn't yet support UART3, so serial console
will still be output on UART0 when booting a upstream kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Most platforms enable these options from Kconfig rather
than the configs header file.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, the USB boot mode is supported by an external loader and
U-boot proper image is put on the section 0. This commit allows
access there.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The DDR SDRAM initialization code has not been mainlined yet, but
U-Boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The DDR SDRAM initialization code has not been mainlined yet, but
U-Boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Before this commit, the Kconfig menu in mach-uniphier only allowed us
to choose one SoC to be compiled. Each SoC has its own defconfig file
for the build-test coverage. Consequently, some defconfig files are
duplicated with only the difference in CONFIG_DEFAULT_DEVICE_TREE and
CONFIG_{SOC_NAME}=y.
Now, most of board-specific parameters have been moved to device trees,
so it makes sense to include init code of multiple SoCs into a single
image as long as the SoCs have similar architecture. In fact, some
SoCs of UniPhier family are very similar:
- PH1-LD4 and PH1-sLD8
- PH1-LD6b and ProXstream2 (will be added in the upcoming commit)
This commit will be helpful to merge some defconfig files for better
maintainability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move init code of low-level debug into a single file.
This is helpful to create an image that runs on multiple SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, IECTRL is enabled after pin-mux settings for the low-level
debugging for PH1-LD4 and PH1-sLD8. While IECTRL is disabled, input
signals are pulled-down, i.e. glitch signal (Low to High transition)
problem occurs if pin-mux is set up first. As a result, one invalid
character is input to the UART block and the auto-boot counting is
terminated immediately.
The correct initialization procedure is:
[1] Enable IECTRL (if IECTRL exists for the pins)
[2] Set up pin-muxing
[3] Deassert the reset of the hardware block
Currently, the low-level debugging is working for PH1-sLD3 and
PH1-Pro4, but just in case, follow the sequence for all the SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I want these prefixed with CONFIG_ARCH_UNIPHIER_ to clarify
they belong to UniPhier SoC family.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
It is no longer necessary to define CONFIG_SUPPORT_CARD_* globally.
Move them to a C file as local macros. Also, rename the C file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The macro, led_write(), is now only used in C sources. There is no
more reason to keep the tricky assembly macro. Replace it with a
new C function led_puts().
Also, rename board.h to micro-support-card.h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The wrapper functions, uniphier_board_*, are just making function
calls complex. Remove them.
Also, use empty inline functions in case CONFIG_MICRO_SUPPORT_CARD
is disabled, so that prototype checking works.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Device tree specifies the available memory ranges in its "/memory"
node. Use it to simplify the CONFIG defines.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
To achieve the complete run-time configuration by device trees, ifdef
conditionals in header files are not preferable.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In UniPhier SoCs before ProXstream2 and PH1-LD6b, two address spaces
0x00000000 - 0x0fffffff
0x40000000 - 0x4fffffff
are both mapped to the external bus (also called system bus),
so either was OK.
In the newest two SoCs, the former (0x00000000 - 0x0fffffff) is
assigned for the serial NOR interface.
Going forward, use the latter for the external bus.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Historically (for compatibility with very old platforms), two
different types of micro support cards have been used with the
UniPhier SoC development boards. It has been painful to maintain
both. Having one of them is enough.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These input enable settings are handled by the pinctrl drivers.
Because the external bus pins are input-enabled by default, on-board
devices such as LED still work fine even with this delayed input
enabling.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As the UniPhier serial driver had already switched to Drive Model
and the pinctrl drivers are now enabled, these pin-muxing settings
are properly handled by the pinctrl drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add "u-boot,dm-pre-reloc" for device nodes we want in SPL DTB
(spl/u-boot-spl.dtb).
The "soc" node (this is simple-bus node) also needs the property
to bind the pinctrl node located under it.
I am collecting this U-Boot specific hack to the bottom of board
DTS rather than inserting "u-boot,dm-pre-reloc" into SoC DTSI.
My goal is to sync DTSI with Linux for easier maintenance.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
boot_mode_apply should be applied only with CONFIG_CMD_BMODE enabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Some i.MXes use __NA_ or 0 to avoid setting mux_mode, but the following patch
only take i.MX6/7 into consideration.
"c3c8a5748897b24f18618047804317167a531dd3 imx-common: fix iomux settings"
Use is_soc_type(MXC_CPU_MX7) to avoid breaking other i.MXes when
setting mux_mode.
In this patch, switch to use "asm/imx-common/sys_proto.h" to avoid
build break for "is_soc_type" for vf610 and mx25.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Rename the socfpga_cyclone5.h to socfpga_cyclone5_socdk.h, and
socfpga_arria.h to socfpga_arria5_socdk.h. This matches the other SoCFPGA
board config files.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
drop select CPU_V7 for board target, since ARCH_MX7 selects CPU_V7.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
When setting iomux for a pin mux, there is no need to check mux_ctrl_ofs.
Also If still checking mux_ctrl_ofs, we have no chance to set iomux
for i.MX7D IOMUXC_LPSR_SW_MUX_CTL_PAD_GPIO1_IO00, because the mux_ctrl_ofs
for this register is 0.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Quark SoC does not support MSR MTRRs. Fixed and variable range MTRRs
are accessed indirectly via the message port and not the traditional
MSR mechanism. Only UC, WT and WB cache types are supported.
We configure all the fixed range MTRRs with common values (VGA RAM
as UC, others as WB) and 3 variable range MTRRs for ROM/eSRAM/RAM as
WB, which significantly improves the boot time performance.
With this commit, it takes only 2 seconds for U-Boot to boot to shell
on Intel Galileo board. Previously it took about 6 seconds.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Now we have enabled PCIe root port on Quark SoC, add its PIRQ
routing information in the device tree as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Thermal sensor on Quark SoC needs to be properly initialized per
Quark firmware writer guide, otherwise when booting Linux kernel,
it triggers system shutdown because of wrong temperature in the
thermal sensor is detected by the kernel driver (see below):
[ 5.119819] thermal_sys: Critical temperature reached(206 C),shutting down
[ 5.128997] Failed to start orderly shutdown: forcing the issue
[ 5.135495] Emergency Sync complete
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
When Linux kernel boots, it hangs at:
[ 0.829408] Intel Quark side-band driver registered
This happens when Quark kernel Isolated Memory Region (IMR) driver
tries to lock an IMR register to protect kernel's text and rodata
sections. However in order to have IMR function correctly, HMBOUND
register must be locked otherwise the system just hangs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Change existing codes to use clrbits, setbits, clrsetbits macros.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On Intel Quark, lots of registers on the message port need be
programmed. Add handy clrbits, setbits, clrsetbits macros for
message port access.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds static register programming for PCIe and USB after memory
init as required by Quark firmware writer guide. Although not doing
this did not cause any malfunction, just do it for safety.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Convert to use DM version of Designware ethernet driver on Intel
quark/galileo.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enabling a PLL while IDDQ is high. The Linux kernel checks for this
condition and warns about it verbosely, so while this seems to work
fine, fix it up according to the programming guidelines provided in
the Tegra K1 TRM (v02p), Section 5.3.8.1 ("PLLC and PLLC4 Startup
Sequence"). The Tegra114 TRM doesn't contain this information, but
the programming of PLLC is the same on Tegra114 and Tegra124.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enabling a PLL while IDDQ is high. The Linux kernel checks for this
condition and warns about it verbosely, so while this seems to work
fine, fix it up according to the programming guidelines provided in
the Tegra K1 TRM (v02p), Section 5.3.8.1 ("PLLC and PLLC4 Startup
Sequence").
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the device tree node for the SPI controllers found on Tegra20 SOCs.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
While clk_m and the oscillator run at the same frequencies on Tegra114
and Tegra124, clk_m is the proper source for the architected timer. On
more recent Tegra generations, Tegra210 and later, both the oscillator
and clk_m can run at different frequencies. clk_m will be divided down
from the oscillator.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On currently supported SoCs, clk_m always runs at the same frequency as
the oscillator input. However newer SoC generations such as Tegra210 no
longer have that restriction. Prepare for that by separating clk_m from
the oscillator clock and allow SoC code to override the clk_m rate.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some platforms have the means to determine the counter frequency at
runtime, so give them an opportunity to do so.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
AFAIK, for all PLLs on all Tegra SoCs, the primary PLL output frequency
is (input * m) / (n * p). However, PLLP's primary output (pllP_out0) on
T210 is the VCO output, and divp is not applied. pllP_out2 does have divp
applied. All other pllP_outN are divided down from pllP_out0. We only
support pllP_out0 in U-Boot at the time of writing.
Fix clock_get_rate() to handle this special case.
This corrects the returned rate for PLLP to be 408MHz rather than 204MHz.
In turn, this causes high enough dividers to be calculated for the various
peripheral clocks that feed off of PLLP. Without this, some peripherals
failed to operate correctly. For instance, one of my SD cards worked
perfectly but an older (presumably slower) card could not be read.
Note that prior to commit 722e000ccd "Tegra: PLL: use per-SoC pllinfo
table instead of PLL_DIVM/N/P, etc.", the calculated PLL frequency was
816MHz since the wrong values were being extracted from the PLLP divider
register. This caused overly large peripheral dividers to be calculated,
which while wrong, didn't cause any correctness issues; things simply ran
slower than they could.
Reported-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This function is deleted by commit 2fccd2d96b
"tegra: Convert tegra GPIO driver to use driver model".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
P2371-2180 is a P2180 CPU board married to a P2597 I/O board. The
combination contains SoC, DRAM, eMMC, SD card slot, HDMI, USB
micro-B port, Ethernet via USB3, USB3 host port, SATA, PCIe, and
two GPIO expansion headers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Commit 0abdd9d0 "arm: Remove nhk8815 boards and nomadik arch" missed one
reference to this arch. Lets remove this as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
This arch does not seem to be supported / used at all in the current
U-Boot mainline source tree any more. So lets remove the core u8500 code
and code that was only referenced by this platform.
Please note that this patch also removes these config options:
- CONFIG_PL011_SERIAL_RLCR
- CONFIG_PL011_SERIAL_FLUSH_ON_INIT
As they only seem to be referenced by u8500 based boards. Without any
such board in the current code, these config option don't make sense
any more. Lets remove them as well.
If someone still wants to use this platform, then please send patches
to re-enable support by adding at least one board that references this
code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
It is not very useful to have the message below on every boot
(especially when we are using early silicon):
U-Boot 2015.10-rc2-23945-g37cf215 (Sep 08 2015 - 14:12:14 -0300)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
, so turn the error message into debug level.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Discard the 'select CPU_V7' from Kconfig in arch/arm/cpu/armv7/mx6
for different targets, because ARCH_MX6 selects CPU_V7.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.
This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
mx6ul_14x14_evk. And we have no way to dymaically checking this chip
is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
POWER related configurations also effect for mx6ul_14x14_evk. But
power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry
Boot Log:
U-Boot SPL 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53)
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C: ready
DRAM: 256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: FEC1
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
This reverts commit 059323fb6a8f21637bb617919715c2427f24777c.
This commit 059323fb6a8f21637bb617919715c2427f24777c use JESD79-3E which
is not the newest spec. Should use JESD79-3F in which tRFC is 260ns for
4Gb chip.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Add imx-common cpu support for imx7d SoC
- Update reset_cause for imx7d
- Enable watchdog driver built for imx7d
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Extend init_aips to support imx7 SoC, use is_soc_type
and is_cpu_type to resolve at run time aips3 settings
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Add imx7d basic SoC system support
Misc arch dependent functions for system bring up
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
* Add Clock control module (CCM) support
* iMX7D SoC introduces 3 main clock sysmtem abstraction for clock
root frequency generation denominated clock slices.
Core clock slice: hihg speed clock for ARM core
Bus clock slice: for bus clocks
IP clock slice: Peripheral clocks
* At system boot ROM enables PLL_ARM, PLL_DDR, PLL_SYS, PLL_ENET
In u-boot, we have to:
- Configure PFD3- PFD7 for freq we needed in u-boot
- Set clock root for peripherals (ip channel)
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
* Add system arch level header files
- imx-regs.h: iMX7D SoC system architecture registers
- crm_regs.h: Clock control module registers
- sys_proto.h: helper callback function for SoC setup
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Add system counter driver for imx7d and mx6ul
imx7 and imx6ul supports system counter timer as well as
GPT timer (arch/arm/imx-common/timer.c); The default for
imx7 is systemcounter timer.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Move common imx6 arch init setup, init.c can be extended
and reused to support imx7 SoC keeping init arch common
code.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Rework cache settings for imx6, move cache configuration
to imx-common/cache.c so it can be reused for newer SoC
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Rework imx_thermal driver to be used across i.MX
processor that support thermal sensor
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
>From source code comments:
"x0: 0 flush & invalidate, 1 invalidate only"
Current value 0xffff can make invalidate work, since we only judge whether
input value is 0 or not, see following code:
"
tbz w1, #0, 1f
dc isw, x9
b 2f
1: dc cisw, x9 /* clean & invalidate by set/way */
2: subs x6, x6, #1 /* decrement the way */
"
Later we may add "2 clean only" support. So following the comments,
correct value from 0xffff to 1.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
The current comments need a bit of tweaking since we now support stack
and global_data relocation in SPL. Also add a reference to the README.
For AArch64 this is not implemented, so leave a TODO for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Tim Harvey <tharvey@gateworks.com>
The current simplify lpc32xx gpio driver implementation assume a
maximum of 32 GPIO per port; there are a total of 22 GPI, 24 GPO
and 6 GPIO to managed on port 3.
Update the driver to fix the following:
1) When requesting GPI_xx and GPO_xx on port 3 (xx is the same number)
the second call to "gpio_request" will return -EBUSY.
2) The status of GPO_xx pin report the status of the
corresponding GPI_xx pin when using the "gpio status" command.
3) The gpio driver may setup the direction register for the wrong
gpio when calling "gpio_direction_input" (GPI_xx) or
"gpio_direction_output" (GPO_xx) on port 3; the call to the
direction is require to use the "gpio status" command.
The following change were done in the driver:
1) port3 GPI are cache in a separate 32 bits in the array.
2) port3 direction register written only for GPIO pins.
3) port3 GPO & GPIO (as output) are read using "p3_outp_state".
4) LPC32XX_GPI_P3_GRP updated to match the change.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add support for Lightwriter SL50 series board, a small, robust and portable
Voice Output Communication Aids (VOCA) designed to meet the particular and
changing needs of people with speech loss resulting from a wide range of
acquired, progressive and congenital conditions.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
This patch adds the "nandecc" command to switch between the SPEAr600 internal
1-bit HW ECC and the 4-bit SW BCH4 ECC. This can be needed to support NAND
chips with a stronger ECC than 1-bit, as on the x600. And to dynamically
switch between both ECC schemes for backwards compatibility.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
This board has not been converted to generic board by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefano Babic <sbabic@denx.de>
These boards have not been converted to generic board by the deadline.
Remove them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefano Babic <sbabic@denx.de>
These boards have not been converted to generic board by the deadline.
Remove dm355evm, dm355leopard, dm365evm, dm6467evm, dvevm, ea20, schmoogie,
sffsdr, sonata.
Signed-off-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to generic board by the deadline.
Remove all cpu9260 and cpuat91 boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
clrsetbits_le32/clrbits_le32 takes mask of the bits as input that
are needed to be set/clear. But emif driver passes the shift of the bits.
Fixing it here.
Reported-by: Mark Mckeown <m-mckeown@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Because there is an originally defined CLK_DMA_ENABLE macro in clk.h,
no reason to add another DMA_CLK_ENABLE macro with the same value.
Remove DMA_CLK_ENABLE, since it does not follow naming convention from
the code, this implies renaming of DMA_CLK_ENABLE to CLK_DMA_ENABLE in
lpc32xx/devices.c file.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
The Wobo i5 top set box is a somewhat curious A10s based top set box,
it uses an AXP209 rather then the AXP152 usually used in combination
with the A10s. It has an ethernet phy connected to PORTD rather then
PORTA, and its built-in usb wifi is connected via the otg controller.
The dts file changes are identical to the changes submitted to the
upstream kernel.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This commits adds a generic support for q8 formfactor a13 based tablets.
These tablets ship in many variants, with the difference mainly being the
touchscreen controller / accelerometer / wifi chip used.
The wifi is USB based, and thus not listed in devicetree.
ATM the kernel does not support the touchscreen / accelerometer on these
devices. In the future we may need multiple configs with different
CONFIG_DEFAULT_DEVICE_TREE settings, this depends on how we solve the
hw differences on the kernel side.
For now this will suffice.
The dts files are identical to the dts files submitted to the upstream
kernel for these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The iNet-tek iNet-1 PCB is a PCB found in various generic 10.1" 1024x600
A10 based tablets such as the Point of View Protab2 XXL and the
Cherry M1007.
This patch has been tested on both rev2 and rev5 of this board / these
tablets.
These tablets feature the usual connectors: headphone, mini hdmi,
power-barrel, mini-usb and a micro-sd slot.
The dts is identical to the dts submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The inet9f-rev03 pcb is specially designed for gaming tablets, such as
the qware tb-g100 tablet.
These 7" tablets feature a dpad, firebuttons and 2 joysticks on the sides
of the screen.
Besides this they have the usual connectors: power-barrel, mini usb,
mini hdmi, headphone and micro-sd slot.
The dts is identical to the dts submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Point of View protab2-ips9 is a tablet with a 9" ips 1024x768 lcd
screen, microsd slot, headphones, mini hdmi, mini usb b and power barrel
connectors.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
USB PHY needs to be properly initialized per Quark firmware writer
guide, otherwise the EHCI controller on Quark SoC won't work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC holds the PCIe controller in reset following a power on.
U-Boot needs to release the PCIe controller from reset. The PCIe
controller (D23:F0/F1) will not be visible in PCI configuration
space and any access to its PCI configuration registers will cause
system hang while it is held in reset.
Enable PCIe controller per Quark firmware writer guide.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
If we convert to use driver model pci on quark, we will encounter
some chicken and egg problems like below:
- To enable PCIe root ports, we need program some registers on the
message bus via pci bus. With driver model, the first time to
access pci bus, the pci enumeration process will be triggered.
But without first enabling PCIe root ports, pci enumeration
just hangs when scanning PCIe root ports.
- Similar situation happens when trying to access GPIO from the
PCIe enabling codes, as GPIO requires its block base address
to be assigned via a pci configuration register in the bridge.
To avoid such dilemma, replace all pci calls in the quark codes
to use the local version which does not go through driver model.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Quark SoC has a low end x86 processor with only 400MHz
frequency. Currently it takes about 15 seconds for U-Boot to
boot to shell and the most time consuming part is with MRC,
which is about 12 seconds. MRC programs lots of registers on
the SoC internal message bus indirectly accessed via pci bus.
To speed up the boot, create an optimized version of pci config
read/write dword routines which directly operate on PCI I/O ports.
These two routines are inlined to provide better performance too.
Now it only takes about 3 seconds to finish MRC, which is really
fast (4 times faster than before).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add one more ethernet device node in the sandbox test device tree,
with name 'sbe5'. This is to support a new test case for testing
network device rotation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a PCI node to the device tree. This allows SPI flash and SATA to work
correctly. Also configure the video to come up correctly even though there
is no keyboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV
based board. The board can boot from SD/MMC. Ethernet is also supported.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add support for DENX MCV SoM, which is CycloneV based and the
associated DENX MCVEVK baseboard. The board can boot from eMMC.
Ethernet and USB is supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Add support for Terasic SoCkit, which is CycloneV based board.
The board can boot either from SD/MMC or QSPI. Ethernet is also
supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Instead of calling board_init_r() directly from board_init_f(), just
return from board_init_f(). This will make the code continue executing
in crt0.S _main(), from which the board_init_r() is called. This patch
aligns the SoCFPGA SPL with the correct SPL design as well as reduces
the stack utilisation slightly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
The SoCFPGA probes mostly from OF and the OF is mandatory both in
U-Boot itself and U-Boot SPL. Enable it by default.
Signed-off-by: Marek Vasut <marex@denx.de>
This fix makes sure that the ISWGRP0 and ISWGRP1 registers are
correctly inited. In case those registers are not initialized,
it is not possible to access the registers synthesised in the
FPGA through the bridges. Any such access produces data abort.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Rework the driver to probe the MMC controller from Device Tree
and make it mandatory. There is no longer support for probing
from the ancient qts-generated header files.
This patch now also removes previous temporary workaround.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Booting the kernel fails on RK3288 (and probably other rockchip SoCs)
when the i-cache is disabled/flushed before d-cache.
I have not investigated whether this is due to U-Boot hanging or whether
it's very early in the linux boot, but following the approach of the
various rockchip U-Boot forks (first disable d-cache then i-cache) makes
things work.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot can't use the sdio card so turn it of to prevent things getting
confused/struck when trying to use the card as storage.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The Firefly RK3288 is a suitable target board for initial mainline Rockchip
support. It includes a good set of peripherals, a recent SoC and it is
readily available.
This adds only some basic files required to allow the baord to display a
serial message in SPL and hang.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a SPI driver for the Rockchip RK3288, using driver model. It should work
for other Rockchip SoCs also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an I2C driver for the Rockchip RK3288, using driver model. It should work
for other Rockchip SoCs also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add code for starting up U-Boot SPL and U-Boot proper. This is generic and
makes use of devices provided by the board- or SoC-specific code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add code to set up the SDRAM in SPL, ready for loading U-Boot. This uses
device tree for configuration so should be able to support other RAM
configurations. It may be possible to generalise the code to support other
SoCs at some point.
Signed-off-by: Simon Glass <sjg@chromium.org>
PMU is the power management unit and GRF is the general register file. Both
are heavily used in U-Boot. Add header files with register definitions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add header files for the peripherals and clocks supported on Rockchip
platforms. The particular implementation (and register set) for each is
SoC-specific, but it seems that the naming can be generic.
Signed-off-by: Simon Glass <sjg@chromium.org>
In SPL we need access to the CRU and other peripherals so we can set up
SDRAM. Mark these so that they will remain in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Bring in required device tree files from Linux. Since mainline Linux is
somewhat behind, use the files from the Chromium tree. We can re-sync once
further code is acccepted upstream.
Signed-off-by: Simon Glass <sjg@chromium.org>
There can be only one do_reset(). When CONFIG_RESET is enabled this is
provided by the reset uclass, and ARM's version should be disabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
These have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Dan Malek <dan@embeddedalley.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Remove CONFIG_LWMON5 references.
(Also, remove undefined CONFIG_WD_MAX_RATE while I am here.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
These have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tolunay Orkun <torkun@nextio.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
Since we need to support runtime check for different drivers, we need
to add get_cpu_rev for vf610, otherwise there will be build errors.
This patch introduces a dummy CPU id which is not read from chip
silicon. Later when we can get the real id from chip, can fix the
value of MXC_CPU_VF610 then.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Suggested-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
There is a hole in shadow registers address map of size 0x100
between bank 5 and bank 6 on iMX6QP, iMX6DQ, iMX6SDL, iMX6SX and iMX6UL.
Bank 5 ends at 0x6F0 and Bank 6 starts at 0x800. When reading the fuses,
we should account for this hole in address space.
Similar hole exists between bank 14 and bank 15 of size
0x80 on iMX6QP, iMX6DQ, iMX6SDL and iMX6SX.
Note: iMX6SL has only 0-7 banks and there is no hole.
Note: iMX6UL doesn't have this one.
When reading, we use register offset, so need to account for holes
to get the correct address.
When writing, we use bank/word index, there is no need to account
for holes, always use bank/word index from fuse map.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
there is a 2b board version of the aristainetos2
board. Differences to the v2:
- spi cs for the nor flash and display controller
changed
- some pinmux changes
- LED gpio settings changed
Signed-off-by: Heiko Schocher <hs@denx.de>
There is no need to expose SoC choice to user, we already got
the SoC according to the build target. So default "select MX6UL"
for MX6UL_14x14_EVK target.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
To i.MX6UL, SYS_L2CACHE_OFF is selected, but there is no Kconfig entry
for SYS_L2CACHE_OFF. Then "select SYS_L2CACHE_OFF" does not effect for
i.MX6UL, which is not expected.
Since SYS_L2CACHE_OFF is mainly used by ARM architecture, add it to
arch/arm/Kconfig.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Add SPL boot support for mx6slevk board.
1. Introduce a configuration file mx6slevk_spl_defconfig.
2. i.MX6SL has same DRAM space with i.MX6SX, need to change SPL DRAM SPACE.
3. Include imx6_spl.h and related SPL macro in mx6slevk.h.
4. select SUPPORT_SPL for TARGET_MX6SLEVK.
5. Add SPL board code to do related initialization.
Boot Log:
U-Boot SPL 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59 +0000)
CPU: Freescale i.MX6SL rev1.2 996 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 50C
Reset cause: POR
Board: MX6SLEVK
I2C: ready
DRAM: 1 GiB
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Add LPDDR2 support:
1. Implement a function mx6_lpddr2_cfg to initialize MMDC for LPDDR2.
2. Introduce a structure mx6_lpddr2_cfg, most entrys are same to
mx6_ddr3_cfg, but still keep it a single one for easy to choose
parameters for LPDDR2.
3. If ddr_type is LPDDR2, use mx6_lpddr2_cfg to init MMDC.
4. Update comments.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
To i.MX6, DDR3 and LPDDR2 is supported, so rename function mx6_dram_cfg
to mx6_ddr3_cfg and the original mx6_dram_cfg function only is a wrapper.
The new reimplemented function mx6_dram_cfg only invokes mx6_ddr3_cfg
when ddr_type is for DDR3. Later we can use ddr_type to initialize
MMDC for LPDDR2.
Initialize ddr_type for different boards which enable SPL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add ddr_type entry for mx6_ddr_sysinfo. It will be used for
differenrate DDR3 and LPDDR2.
Introduce an enum type for ddr_type.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Add mpzqlp2ctl entry for mx6_mmdc_calibration.
MMDC_MPZQLP2CTL register is for init tZQINIT, tZQCL, tZQCS for LPDDR2 chips.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Define two structure mx6sl_iomux_ddr_regs and mx6sl_iomux_grp_regs.
Add a new function mx6sl_dram_iocfg to configure dram io.
Add header file to define macros for register address.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
To Chip density 4Gb, tRFC should be 300ns, see
"Table 61 — Refresh parameters by device density" of JESD79-3E.
tXS(min) is max(5nCK, tRFC(min) + 10ns).
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
i.MX 6SoloLite only supports MMDC0, so do not access MMDC1 for i.MX 6SL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
* Add mxc_gpio support for imx7d SoC
* Use CONFIG_MX7 to extend mxc gpio driver support for imx7d
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
* Add imx7d support for iomux controller
* imx7d has two iomux controllers iomuxc (0x3033000) and iomuxc-lpsr
(0x302C0000) each conroller provides control and mux mode pad
registers but shares iomuxc input select register with iomuxc-lpsr
IOMUX_CONFIG_LPSR flag is used to properly set daisy chain settings
for iomuxc-lpsr pads.
* Since mx7d introduces LPSR IOMUX pins, add new base to IOMUX v3
driver for these LPSR pins.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
To i.MX6SX/UL, two ethernet interfaces are supported.
Add ENET2 clock support:
1. Introduce a new input parameter "fec_id", only 0 and 1 are allowed.
To value 1, only i.MX6SX/UL can pass the check.
2. Modify board code who use this api to follow new api prototype.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nikolaos Pasaloukos <Nikolaos.Pasaloukos@imgtec.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Move most macro definitions and prototypes into
"arch/arm/include/asm/imx-common/sys_proto.h" to avoid duplicated
function prototypes and marco definitions for different i.MX SoCs.
This patch do not remove the sys_proto.h for different i.MX SoCs,
because we need to modify lots of driver code and others. This patch
remove duplicated macros and prototypes and incude "sys_proto.h"
of imx-common for each sys_proto.h of different i.MX platforms.
Then later we should avoid add stuff in sys_proto.h of each platform,
and modify driver to include common sys_proto.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Rewrite get_cpu_rev, from "static const char *get_cpu_rev(void)" to
"u32 get_cpu_rev(void)". To align with get_cpu_rev of other i.MXes.
Also write get_imx_type to replace get_cpu_type, since we have
macro named get_cpu_type.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Use new formula for get_cpu_rev, since we need to use this formula
to do runtime check for all i.MXes.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Implement get_cpu_rev to support runtime check using is_cpu_type.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Move TARGET_xx Kconfig option based on mx6 to arch/arm/cpu/armv7/mx6/Kconfig.
Add enable "CONFIG_ARCH_MX6" for boards based on mx6.
Then we can choose target boards using "make ARCH=arm menuconfig"
with ARCH_MX6 defined.
If using original way, we have no chance to enable ARCH_MX6 when
"make menuconfig". Even define CONFIG_ARCH_MX6=y in xx_defconfig,
kconfig will complains "arch/../configs/platinum_titanium_defconfig:3:
warning: override: TARGET_PLATINUM_TITANIUM changes choice state"
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Soeren Moch <smoch@web.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Soeren Moch <smoch@web.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This commit adds ethernet support to the TS4800. Note that the
MAC address is not fused on this board and have to be read from
FEC PALR PAUR registers (this is how the kernel provided by
Technologic Systems does it).
signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Stefano Babic <sbabic@denx.de>
This commit adds basic support including:
MMC, Serial console, TS4800 watchdog
The config use CONFIG_SKIP_LOWLEVEL_INIT as U-boot is used as a second
stage bootloader.
Signed-off-by: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Stefano Babic <sbabic@denx.de>
Remove this ad-hoc mkimage invocation in MXS Makefile and replace
it with the standard mkimage rule instead.
This patch fixes recent build issues introduced by the patch
92a655c mkimage: Set up a file size parameter and keep it updated
These build issues could be triggered by building for example the
MX28EVK and the u-boot.sb image:
$ make mx28evk_defconfig
$ make V=1 u-boot.sb
[...]
make -f ./scripts/Makefile.build obj=arch/arm/cpu/arm926ejs/mxs u-boot.sb
./tools/mkimage -n arch/arm/cpu/arm926ejs/mxs/mxsimage.mx28.cfg -T mxsimage u-boot.sb
./tools/mkimage: Can't open (null): Bad address
arch/arm/cpu/arm926ejs/mxs/Makefile:82: recipe for target 'u-boot.sb' failed
make[1]: *** [u-boot.sb] Error 1
Makefile:989: recipe for target 'u-boot.sb' failed
make: *** [u-boot.sb] Error 2
With this patch:
./tools/mkimage -n arch/arm/cpu/arm926ejs/mxs/mxsimage.mx28.cfg -T mxsimage -d arch/arm/cpu/arm926ejs/mxs/mxsimage.mx28.cfg u-boot.sb
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Juha Lumme <juha.lumme@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently we need to build one U-boot image for each of the udoo
variants: quad and dual-lite.
By switching to SPL we can support all two variants with a single binary.
Based on the SPL for wandboard.
Tested with OpenELEC (Open Embedded Linux Entertainment Center)
on both boards.
Signed-off-by: Peter Vicman <peter.vicman@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Peter Vicman <peter.vicman@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch rewrites MMU translation table entries. To start, all table
entries are written as "invalid", then "device-ngnrnr" and "normal" are
written to the entries to enable access to specific addresses.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
