The OMAP36xx/OMAP37xx family uses L3 frequency of 200MHz instead of 165MHz
used by OMAP34xx/OMAP35xx.
Also fix checkpatch warning about alignment.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Currently in OMAP3 SPL, the GPMC for NAND is configured for 16bit
access. This patch adds support for 8bit NAND devices as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
The timer_init function is called before relocation and writes to bss data
were corrupting relocation data. Fix this by removing the call to
reset_timer_masked. The initial timer count should be 0 or near 0 anyway,
so initializing the variables are not needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The 150MHz clock rate gives u-boot time functions problems and there's no
benefit to a fast clock, so lower the rate.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
Provide proper setting for the APLL fout frequency calculation for
Exynos4 based targets (especially Exynos4210 - Trats board).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
There are differnce with clock calcuation by cpu variations.
This patch will fix it according to user manual.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
This patch performs the following:
1) Convert the assembly code for memory and clock initialization to C code.
2) Move the memory and clock init codes from board/samsung to arch/arm
3) Creat a common lowlevel_init file across Exynos4 and Exynos5. Converted
the common lowlevel_init from assembly to C-code
4) Made spl_boot.c and tzpc_init.c common for both exynos4 and exynos5.
5) Enable CONFIG_SKIP_LOWLEVEL_INIT as stack pointer initialisation is already
done in _main.
6) exynos-uboot-spl.lds made common across SMDKV310, Origen and SMDK5250.
TEST: Tested SD-MMC boot on SMDK5250 and Origen.
Tested USB and SPI boot on SMDK5250
Compile tested for SMDKV310.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch configures the gpio values for UART
on Origen and SMDKV310 using pinmux
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds APIs to get power reset status and exit the wakeup condition for
both exynos5 and exynos4
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The omap_gpio driver is used by AM33XX, OMAP3/4, OMAP54XX and DRA7XX SoCs.
These SoCs have different gpio count but currently omap_gpio driver uses hard
coded 192 which is wrong.
This patch fixes this issue by:
1. Move define of OMAP_MAX_GPIO to all arch/arm/include/asm/arch-omap*/gpio.h.
2. Update gpio bank settings and enable GPIO modules 7 & 8 clocks for OMAP5.
Thanks for Lubomir Popov to provide valuable comments to fix this issue.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Heiko Schocher <hs@denx.de>
During SDRAM_AUTO_DETECTION MA is not configured.
For Soc's > OMAP4460 MA is present. So populating
MA for the same.
Tested on OMAP4430 PANDA, OMAP4460 PANDA.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
For tracing to work it has to be able to access the microsecond timer
without causing a recursive call to the function entry/exit handlers.
Add attributes to the relevant functions to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
move uart soft reset code to common place and call
this function from board code, instead of copy and paste
this code for every board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
[trini: Fix igep0033 build, remove 'regval' on pcm051]
Signed-off-by: Tom Rini <trini@ti.com>
upcoming support for siemens boards switches mpu pll clk in board
code. So make this configurable.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
move rtc32k_enable() to common place so all am33xx boards can use it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
This patch initialises the local variable 'shift' to zero.
The uninitialised local variable 'shift' had garbage value and was
resulting in unwnated results in the functions exynos5_get_mmc_clk()
and exynos4_get_mmc_clk().
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
auxclk0 and auxclk1 are utilized on some OMAP5 boards.
Define the infrastructure needed for accessing them
without using magic numbers.
Also remove unrelated TPS62361 defines from clocks.h
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
DRA7 EVM board has the below configuration. Adding the
settings for the same here.
2Gb_1_35V_DDR3L part * 2 on EMIF1
2Gb_1_35V_DDR3L part * 4 on EMIF2
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update PLL values.
SYS_CLKSEL value for 20MHz is changed to 2. In other platforms
SYS_CLKSEL value 2 represents reserved. But in sys_clk array
ind 1 is used for 13Mhz. Since other platforms are not using
13Mhz, reusing index 1 for 20MHz.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
The sys_clk on the dra evm board is 20MHZ.
Changing the configuration for the same.
And also moving V_SCLK, V_OSCK defines to
arch/clock.h for OMAP4+ boards.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Slew rate compensation cells are not present for DRA7xx
Soc's. So return from function srcomp_enable() if soc is not
OMAP54xx.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DRA752 now uses AVS Class 0 voltages which are voltages in efuse.
This means that we can now use the optimized voltages which are
stored as mV values in efuse and program PMIC accordingly.
This allows us to go with higher OPP as needed in the system without
the need for implementing complex AVS logic.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In DRA7xx Soc's voltage scaling is done using GPI2C.
So i2c_init should happen before scaling. I2C driver
uses __udelay which needs timer to be initialized.
So moving timer_init just before voltage scaling.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
TPS659038 is the power IC used in DRA7XX boards.
Adding support for this and also adding pmic data
for DRA7XX boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Voltage scaling can be done in two ways:
-> Using SR I2C
-> Using GP I2C
In order to support both, have a function pointer in pmic_data
so that we can call as per our requirement.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
SGX clocks should be enabled only for OMAP5 ES1.0.
So this can be removed.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The newly introduced function setup_warmreset_time(), called
from within prcm_init(), tries to write to the prm_rsttime
OMAP5 register. The struct member holding this register's
address is however initialized for OMAP5 ES2.0 only. On ES1.0
devices this uninitialized value causes a second (warm) reset
at startup.
Add .prm_rsttime address init to the ES1.0 struct.
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Tom Rini <trini@ti.com>
Patch adds a call of abb_setup() function, and proper registers
definitions needed for ABB setup sequence. ABB is initialized
for MPU voltage domain.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Adaptive Body Biasing (ABB) modulates transistor bias voltages
dynamically in order to optimize switching speed versus leakage.
Adaptive Body-Bias ldos are present for some voltage domains
starting with OMAP3630. There are three modes of operation:
* Bypass - the default, it just follows the vdd voltage
* Foward Body-Bias - applies voltage bias to increase transistor
performance at the cost of power. Used to operate safely at high
OPPs.
* Reverse Body-Bias - applies voltage bias to decrease leakage and
save power. Used to save power at lower OPPs.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
We need to call the save_omap_boot_params function on am33xx/ti81xx and
other newer TI SoCs, so move the function to boot-common. Only OMAP4+
has the omap_hw_init_context function so add ifdefs to not call it on
am33xx/ti81xx. Call save_omap_boot_params from s_init on am33xx/ti81xx
boards.
Reviewed-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This requires that cpu_is_exynos4/5 should be made available before tzpc_init.
Hence this patch also makes necessary changes to have cpu_info in spl and
invokes arch_cpu_init before tzpc_init in low_level_init.S for smdk5250.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
tzpc_init is common for all exynos5 boards, hence move it to
armv7/exynos so that all other boards can use it.
Also update the smdk5250 Makefile and config file.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds generic codes to support Freescale's Vybrid VF610 CPU.
It aligns Vybrid VF610 platform with i.MX platform. As there are
some differences between VF610 and i.MX platforms, the specific
codes are in the arch/arm/cpu/armv7/vf610 directory.
Signed-off-by: Alison Wang <b18965@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Replace all relocate_code routines from ARM start.S files
with a single instance in file arch/arm/lib/relocate.S.
For PXA, this requires moving the dcache unlocking code
from within relocate_code into c_runtime_cpu_setup.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Simon Glass <sjg@chromium.org>
According to the latest exynos5 user manual, the equation for
calculating PLL output was changed to
FOUT= MDIV x FIN/(PDIV x 2^SDIV)
earlier it was
FOUT= MDIV x FIN/(PDIV x 2^(SDIV -1))
So updating the clock code accordingly.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add sama5d3xek support with following feature
- boot from NAND flash, PMECC support, 4bit ECC @ 512 bytes sector
- boot from SPI flash support
- boot from SD card support
- LCD support
- EMAC support
- USB OHCI support
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
