Commit Graph

686 Commits

Author SHA1 Message Date
Tom Rix
23b80982a0 Add support for Eukrea CPU9260/CPU9G20 SBC
these boards are built around Atmel's AT91SAM9260/9G20 and have
up to 64MB of NOR flash, up to 128MB of SDRAM, up to 2GB of NAND
and include a 10/100 Ethernet PHY in RMII mode.

Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-10-13 06:17:35 -05:00
Tom Rix
d8380c9d35 Add support for Eukrea CPUAT91 SBC
CPUAT91 is built around Atmel's AT91RM9200 and has up to 16MB of NOR
flash, up to 128MB of SDRAM, and includes a Micrel KS8721 PHY in RMII
mode.

Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-10-13 06:17:35 -05:00
Mingkai Hu
e40ac4870c On-chip ROM boot: MPC8536DS support
The MPC8536E is capable of booting from the on-chip ROM - boot from
eSDHC and boot from eSPI. When power on, the porcessor excutes the
ROM code to initialize the eSPI/eSDHC controller, and loads the mian
U-Boot image from the memory device that interfaced to the controller,
such as the SDCard or SPI EEPROM, to the target memory, e.g. SDRAM or
L2SRAM, then boot from it.

The memory device should contain a specific data structure with control
word and config word at the fixed address. The config word direct the
process how to config the memory device, and the control word direct
the processor where to find the image on the memory device, or where
copy the main image to. The user can use any method to store the data
structure to the memory device, only if store it on the assigned address.

The on-chip ROM code will map the whole 4GB address space by setting
entry0 in the TLB1, so the main image need to switch to Address space 1
to disable this mapping and map the address space again.

This patch implements loading the mian U-Boot image into L2SRAM, so
the image can configure the system memory by using SPD EEPROM.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-09-30 08:42:11 -05:00
Mingkai Hu
9a1a0aedbb NAND boot: MPC8536DS support
MPC8536E can support booting from NAND flash which uses the
image u-boot-nand.bin. This image contains two parts: a 4K
NAND loader and a main U-Boot image. The former is appended
to the latter to produce u-boot-nand.bin. The 4K NAND loader
includes the corresponding nand_spl directory, along with the
code twisted by CONFIG_NAND_SPL. The main U-Boot image just
like a general U-Boot image except the parts that included by
CONFIG_SYS_RAMBOOT.

When power on, eLBC will automatically load from bank 0 the
4K NAND loader into the FCM buffer RAM where CPU can execute
the boot code directly. In the first stage, the NAND loader
copies itself to RAM or L2SRAM to free up the FCM buffer RAM,
then loads the main image from NAND flash to RAM or L2SRAM
and boot from it.

This patch implements the NAND loader to load the main image
into L2SRAM, so the main image can configure the RAM by using
SPD EEPROM. In the first stage, the NAND loader copies itself
to the second to last 4K address space, and uses the last 4K
address space as the initial RAM for stack.

Obviously, the size of L2SRAM shouldn't be less than the size
of the image used. If so, the workaround is to generate another
image that includes the code to configure the RAM by SPD and
load it to L2SRAM first, then relocate the main image to RAM
to boot up.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-09-30 08:42:06 -05:00
Wolfgang Denk
5e498dfab8 Merge branch 'master' of /home/wd/git/u-boot/custodians 2009-09-24 23:40:25 +02:00
Paul Gortmaker
2738bc8df6 sbc8548: allow enabling PCI via a make config option
Prior to this commit, to enable PCI, you had to go manually
edit the board config header, and if you had 33MHz PCI, you
had to manually change CONFIG_SYS_NS16550_CLK too, which was
not real user friendly,

This adds the typical PCI and clock speed make targets to the
toplevel Makefile in accordance with what is being done with
other boards (i.e. using the "-t" to mkconfig).

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-09-24 12:05:00 -05:00
Peter Tyser
55f786d8ba MAKEALL: Use POSIX math
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-09-24 00:37:43 +02:00
Peter Tyser
40a28f0885 MAKEALL: Add summary information
This change adds some basic summary information to the MAKEALL script.
The summary information includes how many boards were compiled, how many
boards had compile warnings or errors, and which specific boards had
compile warnings or errors.

This information is useful when doing compile testing to quickly
determine which boards are broken.

As a side benefit, no empty $BOARD.ERR files are generated by MAKEALL.
Previously, each board had a corresponding $BOARD.ERR file, even if the
board compiled cleanly.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-09-24 00:37:41 +02:00
Wolfgang Denk
041a6a0c2e Merge branch 'master' of git://git.denx.de/u-boot-microblaze 2009-09-15 21:45:50 +02:00
Michal Simek
13916abf99 microblaze: Remove AtmarkTechno Suzaku board
Users should use microblaze-generic platform.
This platform is longer not supported.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-09-14 14:40:04 +02:00
Dirk Eibach
4c1883670a ppc4xx: Rename compactcenter to intip
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-09-11 10:37:47 +02:00
Wolfgang Denk
3ea43ff773 Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-09-07 23:12:46 +02:00
Frederik Kriewitz
c35d7cf071 Add support for the DevKit8000 board
This patch adds support for the DevKit8000 board.

Signed-off-by: Frederik Kriewitz <frederik@kriewitz.eu>
2009-09-05 01:33:14 +02:00
Harald Krapfenbauer
4640c2b869 Blackfin: cm-bf537u: new board port
The CM-BF537U is similar to the CM-BF537E module, but enough to need its
own board port.

Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-02 05:58:37 -04:00
Albin Tonnerre
2dc851e3b0 Support for the Calao TNY-A9260/TNY-A9G20 boards
The Calao TNY-A9260 and TNY-9G20 are boards manufactured and sold by
Calao Systems <http://www.calao-systems.com>. Their components are very
similar to the AT91SAM9260EK board, so their configuration is based on
the configuration of this board. There are however some differences:
different clocks, no LCD, no ethernet. They also can use SPI EEPROM to
store the environment.

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-09-01 22:35:58 +02:00
Albin Tonnerre
9453967e28 Add support for the Calao SBC35-A9G20 board
The Calao SBC35-A9G20 board is manufactured and sold by Calao Systems
<http://www.calao-systems.com>. It is built around an AT91SAM9G20 ARM SoC
running at 400MHz. It features an Ethernet port, an SPI RTC backed by an onboard
battery , an SD/MMC slot, a CompactFlash slot, 64Mo of SDRAM, 256Mo of NAND
flash, two USB host ports, and an USB device port. More informations can be
found at <http://www.calao-systems.com/articles.php?lng=en&pg=5936>

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
2009-09-01 22:13:37 +02:00
Ilya Yanok
10bc241dfc imx27lite: add support for imx27lite board from LogicPD
This patch adds support for i.MX27-LITEKIT development board from
LogicPD. This board uses i.MX27 SoC and has 2MB NOR flash, 64MB NAND
flash, FEC ethernet controller integrated into i.MX27.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Wolfgang Denk <wd@denx.de>
2009-09-01 22:10:55 +02:00
Poonam Aggrwal
c17b79fbd0 85xx: Added support for P1011RDB and P2010RDB
P1011 and P2010 are single core variants of P1010 and P2020 respectively.
The board(RDB) will be same.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28 17:12:42 -05:00
Poonam Aggrwal
bf488bc094 85xx: P1020RDB Support Added
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28 17:12:41 -05:00
Poonam Aggrwal
728ece343e 85xx: Add support for P2020RDB board
The code base adds P1 & P2 RDB platforms support.
The folder and file names can cater to future SOCs of P1/P2 family.
P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series.

Tested following on P2020RDB:
1. eTSECs
2. DDR, NAND, NOR, I2C.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28 17:12:38 -05:00
Eric Millbrandt
5b53b29bc2 Add support for the galaxy5200
Add support for the DEKA Research and Development galaxy5200 board

The galaxy5200 is an Freescale mpc5200 based embedded industrial
control board.

Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
2009-08-25 12:57:55 +02:00
Wolfgang Denk
cb32ed1fc2 Merge branch 'next' of git://git.denx.de/u-boot-coldfire 2009-08-04 21:54:11 +02:00
Wolfgang Denk
d7b0781e2b Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2009-07-29 09:25:52 +02:00
Dirk Eibach
ab4c62c1ba ppc4xx: Add GDsys CompactCenter board support.
Board support for the Guntermann & Drunck CompactCenter and
DevCon-Center.
Based on the AMCC Canyonlands board support by Stefan Roese.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-28 07:20:34 +02:00
Reinhard Arlt
c2e49f706b mpc83xx: Add esd VME8349 board support
This patch adds support for the esd VME8349 board equipped with the
MPC8349. It's a VME PMC carrier board equipped with the Tundra
TSI148 VME-bridge.

Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-07-27 18:36:36 -05:00
Matthias Fuchs
99d8b23bc7 ppc4xx: Add 405EP based PMC405DE board
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24 06:47:40 +02:00
Peter Tyser
10c1b21855 xpedite1k: Move to X-ES vendor directory
The XPedite1000 is an X-ES product thus it can be put in board/xes along
with other X-ES boards.  Along with the move, the board was renamed to
XPedite1000 from XPedite1K to fit X-ES's standard naming convention.
Maintainership was also transfered to Peter Tyser.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24 06:42:32 +02:00
Dirk Eibach
b209a11482 ppc4xx: Add DL-Vision 405EP board support
Board support for the Guntermann & Drunck DL-Vision.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24 06:42:31 +02:00
Prafulla Wadaskar
fbc8365ad7 Marvell RD6281A Board support
This is Marvell's 88F6281_A0 based reference design board

This patch is tested for-
1. Boot from DRAM/NAND flash/NFS
2. File transfer using tftp and loadb
3. NAND flash read/write/erase

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-07-23 00:14:40 +02:00
Prafulla Wadaskar
4abc5bffea Marvell MV88F6281GTW_GE Board support
This is Marvell's 88F6281_A0 based custom board developed
for wireless access point product

This patch is tested for-
1. Boot from DRAM/SPI flash/NFS
2. File transfer using tftp and loadb
3. SPI flash read/write/erase
4. Booting Linux kernel and RFS from SPI flash
5. Boot from USB supported

Reviewed-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2009-07-18 20:41:42 +02:00
Prafulla Wadaskar
55dd4ba541 Marvell Sheevaplug Board support
Reference:
http://plugcomputer.org/
http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support

This patch is tested for-
1. Boot from DRAM/NAND flash
2. File transfer using tftp
3. NAND flash read/write/erase
4. Linux kernel and RFS Boot from NAND
5. Enabled USB PHY init for kernel need
6. Boot from USB supported

Note: to boot Kirkwood kernel with USB support,
	you should add "usb start" in the boot sequence

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2009-07-18 18:46:09 +02:00
TsiChung Liew
bf9a521529 ColdFire: Add M5208EVB and MCF520x CPU support
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
2009-07-14 09:27:17 -05:00
Wolfgang Denk
87abce6e91 Merge branch 'master' of /home/wd/git/u-boot/master 2009-07-14 00:00:04 +02:00
Wolfgang Denk
c3ae126c2c Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-07-13 23:45:02 +02:00
Sedji Gaouaou
5ccc2d99d6 at91: Introduction of at91sam9g10 SOC.
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
2009-07-12 17:56:11 +02:00
Sedji Gaouaou
22ee647380 at91: Introduction of at91sam9g45 SOC.
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
2009-07-12 17:43:34 +02:00
Nobuhiro Iwamatsu
74d9c16a68 sh: Add support ESPT-GIGA borad
ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.

More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-07-11 09:02:21 +09:00
Jon Smirl
c9969947a4 board support patch for phyCORE-MPC5200B-tiny
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1

Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
2009-07-10 23:21:32 +02:00
Wolfgang Denk
a48ecc969f Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	drivers/spi/Makefile

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-07 22:22:05 +02:00
Jean-Christophe PLAGNIOL-VILLARD
ceb70b466e nhk8815: fix MAKEALL
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-07-06 21:53:21 +02:00
Magnus Lilja
d08e5ca301 MX31: Add NAND SPL boot support to i.MX31 PDK board.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2009-07-06 21:53:18 +02:00
Stefano Babic
040f8f63e9 xscale: add support for the polaris board
The Polaris board is based on the TrizepsIV module of
Keith & Koep (http://www.keith-koep.com).

Signed-off-by: Stefano Babic <sbabic@denx.de>
2009-07-06 21:52:58 +02:00
Daniel Gorsulowski
33b1d3f43a at91: Add esd gmbh MEESC board support
This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.

Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
2009-07-06 21:52:50 +02:00
Magnus Lilja
8449f287f5 MX31: Add basic support for Freescale i.MX31 PDK board.
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).

This patch assumes that some other program performs the actual
NAND boot.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-07-06 21:52:38 +02:00
Peter Tyser
5da6f806b4 86xx: XPedite5170 board support
Initial support for Extreme Engineering Solutions XPedite5170 -
a MPC8640-based 3U VPX single board computer with a PMC/XMC
site.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-07-01 23:25:48 -05:00
Ilko Iliev
3294923297 at91: add support for the PM9261 board of Ronetix GmbH
The PM9261 board is based on the AT91SAM9261-EK board.

Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.html

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:11 +02:00
Hoan Hoang
0f52b560f1 Blackfin: ibf-dsp561: new board port
Signed-off-by: Hoan Hoang <hnhoan@i-syst.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:11 -04:00
Mike Frysinger
3088189a15 Blackfin: blackstamp: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:11 -04:00
Mike Frysinger
59ac972970 Blackfin: bf537-srv1: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:10 -04:00
Mike Frysinger
d7fdc1410b Blackfin: bf537-minotaur: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:09 -04:00
Mike Frysinger
cb4b5e874f Blackfin: bf537-pnav: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:08 -04:00
Mike Frysinger
59e4be945b Blackfin: cm-bf527: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:07 -04:00
Mike Frysinger
8b219cf07c Blackfin: cm-bf548: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:07 -04:00
Mike Frysinger
9417d9a213 Blackfin: tcm-bf537: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:06 -04:00
Mike Frysinger
e548321af0 Blackfin: cm-bf561: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:06 -04:00
Mike Frysinger
8a9bab08a6 Blackfin: cm-bf537e: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:05 -04:00
Mike Frysinger
e82d8a1f02 Blackfin: cm-bf533: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:04 -04:00
Srikanth Srinivasan
feb7838f97 85xx: Add P2020DS support
The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.

Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-12 17:16:25 -05:00
Stefan Roese
e53b507cee mpc512x: Add esd gmbh mecp5123 board support
MECP5123 is a MPC5121E based module by esd gmbh.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
2009-06-12 20:47:19 +02:00
Wolfgang Denk
52568c3654 MPC512x: add support for ARIA board
ARIA is a MPC5121E based COM Express module by Dave/DENX.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
2009-06-12 20:47:16 +02:00
Wolfgang Denk
72601d04fd Rename ads5121 board into mpc5121ads
We rename the board so we use a consistent name in U-Boot and in
Linux.  Also, we use this opportunity to move the board into the
Freecale vendor directory.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
2009-06-12 20:47:16 +02:00
David Brownell
28b00324be dm355 evm support
Initial U-Boot support for the DaVinci DM355 EVM.  This is a board
from Spectrum Digital.  Board docs include schematic and firmware
for its microcontroller:

  http://c6000.spectrumdigital.com/evmdm355/revd/

Most of the DM355 chip is fully documented by TI, the most notable
exception being the MPEG/JPEG coprocessor (programmable using codecs
available at no cost from TI), which is omitted from its DM335 sibling:

  http://focus.ti.com/docs/prod/folders/print/tms320dm355.html

This version can boot from the on-board DM9000 Ethernet chip, after
being loaded (from NAND, MMC/SD, or UART).  In the near future, NAND
and USB support could be added ... NAND support is being held back
until the support for the 4-bit ECC hardware is ready.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-06-12 20:39:51 +02:00
Tom Rix
376aee78dd ZOOM2 Add initial support for Zoom2
Zoom2 is a new board from Texas Instruments and LogicPD

The logicpd web site is a good source for general information on this board.
Please start looking here if the below links are broken.
http://www.logicpd.com

This is a pdf of the product
http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf
This is the product description web page
http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp

This patch provides a zoom2 base target by copying zoom1 and by making some
obvious changes.

To configure, run
make omap3_zoom2_config

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:50 +02:00
Heiko Schocher
3c1d89545d 82xx, ids8247: added ids8247 board to MAKEALL script
Signed-off-by: Heiko Schocher <hs@denx.de>
2009-05-15 21:17:27 +02:00
Ilko Iliev
f0a2c7b4b6 at91: add support for the PM9263 board of Ronetix GmbH
The PM9263 board is based on the AT91SAM9263-EK board.

Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.html

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-16 21:30:48 +02:00
Ulf Samuelsson
cb82a53266 Add support for the AT91RM9200EK Board.
The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507

with
	- NOR (cfi driver)
	- DataFlash
	- USB OHCI
	- Net
	- I2C (hard)

Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04 20:42:20 +02:00
Mike Frysinger
84a9dda324 Blackfin: bf518f-ezbrd: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:46 -04:00
Mike Frysinger
0c31ddf7b7 Blackfin: bf526-ezbrd: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:42 -04:00
Mike Frysinger
5c45f7cac2 Blackfin: bf538f-ezkit: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:38 -04:00
Mike Frysinger
d9a5d113b9 Blackfin: bf527-ezkit: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:35 -04:00
Mike Frysinger
76d21803dd Blackfin: bf548-ezkit: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:29 -04:00
Haiying Wang
765547dc5e MPC85xx: Add MPC8569MDS board support
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-03-30 13:33:51 -05:00
Wolfgang Denk
aaa0e0812f Merge branch 'master' of git://git.denx.de/u-boot-at91 2009-03-26 22:27:45 +01:00
Guennadi Liakhovetski
0c6926736e ARM: Add the imx31_phycore_eet board to MAKEALL
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2009-03-25 22:23:07 +01:00
Nicolas Ferre
df486b1fa3 at91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.

The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337

Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 14:48:16 +01:00
Grzegorz Bernacki
5c4fa9b474 Add support for the digsy MTC board.
This is the InterControl custom device based on the MPC5200B chip.

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2009-03-20 22:39:14 +01:00
Heiko Schocher
1b6275dfb1 8xx: add support for new keymile kmsupx4 board.
This patch adds support for the kmsupx4 board from Keymile,
based on a Freescale MPC852T CPU

- serial console on SMC1
- 32 MB SDRAM
- 32 MB NOR Flash
- Ethernet over SCC3
- I2C Bitbang

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-03-18 20:50:05 +01:00
Wolfgang Denk
9eb468da3f Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-02-19 00:46:32 +01:00
Wolfgang Grandegger
a865bcdac8 MPC85xx: TQM8548: add support for the TQM8548_AG module
The TQM8548_AG is a variant of the TQM8548 module with 1 GiB memory,
CAN and without PCI/PCI-X and RTC. U-Boot can be built for this module
with "$ make TQM8548_AG_config".

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:05:59 -06:00
Wolfgang Grandegger
ad7ee5d43b MPC85xx: TQM8548: add support for the TQM8548_BE module
The TQM8548_BE is a variant of the TQM8548 module with NAND and CAN
interface. With NAND support, the image is significantly larger and
TEXT_BASE is adjusted accordingly. U-Boot can be built for this
module with "$ make TQM8548_BE_config".

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:05:59 -06:00
Ilya Yanok
0d19f6c8cb qong: support for Dave/DENX QongEVB-LITE board
This patch adds support for Dave/DENX QongEVB-LITE i.MX31-based board.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-10 00:22:31 +01:00
Wolfgang Denk
6c6e042ab3 Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-02-01 21:38:07 +01:00
Dirk Behme
7379f45a7b OMAP3: Add Zoom1 board support
Support for Zoom MDK with OMAP3430. Details of Zoom MDK available here:
http://www.logicpd.com/products/devkit/ti/zoom_mobile_development_kit

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:40:16 +01:00
Dirk Behme
2be2c6cc67 OMAP3: Add Pandora support
Add Pandora support.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:39:58 +01:00
Dirk Behme
ad9bc8e52d OMAP3: Add EVM board
Add EVM board support.

Signed-off-by: Manikandan Pillai <mani.pillai@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:39:58 +01:00
Dirk Behme
9d0fc8110e OMAP3: Add Overo board
Add Overo board support.

Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:39:57 +01:00
Dirk Behme
f904cdbb68 OMAP3: Add common power code, README, and BeagleBoard
Add BeagleBoard support, common power code and README.

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-01-28 21:39:15 +01:00
Wolfgang Denk
49ad480171 Merge branch 'master' of git://git.denx.de/u-boot-mips 2009-01-27 20:55:57 +01:00
Stefan Roese
2a61eff6a8 MIPS: Add VCT board series support (Part 3/3)
Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-27 23:08:26 +09:00
Dirk Eibach
89b8619aae ppc4xx: Add GDsys PowerPC 440 ETX board support.
Board support for the Guntermann & Drunck PowerPC 440 ETX module.
Based on the AMCC Yosemite board support by Stefan Roese.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-26 10:13:30 +01:00
Alessandro Rubini
d5254f149d Initial support for Nomadik 8815 development board
The NMDK8815 board is distributed by ST Microelectornics.
Other (proprietary) code must be run to unlock the CPU before
U-Boot runs. doc/README.nmdk8815 outlines the boot sequence.

This is the initial port, with basic infrastructure and
a working serial port.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-24 18:10:37 +01:00
Wolfgang Denk
8f86a3636e Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2009-01-24 02:17:02 +01:00
Wolfgang Denk
1ea0823786 Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx 2009-01-24 02:08:31 +01:00
Graeme Russ
c620c01e96 Added initial eNET board support
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2009-01-24 01:01:16 +01:00
Kim Phillips
833d94bcdc Merge branch 'next' 2009-01-23 17:48:24 -06:00
Heiko Schocher
de0443614a powerpc: 83xx: add support for the kmeter1 board
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.

- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-01-24 00:36:19 +01:00
Kumar Gala
18af1c5f0f 85xx: Add a 36-bit physical configuration for MPC8572DS
We move all IO addressed (CCSR, localbus, PCI) above the 4G boundary
to allow for larger memory sizes.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-23 17:09:18 -06:00
Ron Madrid
5bb907a492 mpc83xx: New board support for SIMPC8313
This patch will create a new board, SIMPC8313, from Sheldon Instruments.  This
board boots from NAND devices and is configureable for either large or small
page devices.  The board supports non-soldered DDR2, one ethernet port, a
Marvell 88E1118 PHY, and PCI host support.  The board also has a FPGA connected
to the eLBC providing glue logic to a TMS320C67xx DSP.

Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-01-23 11:31:18 -06:00
Michal Simek
52a822ed9c microblaze: Rename ml401 to microblaze-generic
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-01-23 10:39:56 +01:00
Kim Phillips
be4880ebe4 Merge branch 'master' into next 2009-01-21 18:38:51 -06:00
Peter Tyser
78bbc5ce15 XPedite5200 board support
Initial support for Extreme Engineering Solutions XPedite5200 -
a MPC8548-based PMC single board computer.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-19 18:18:51 -06:00
Peter Tyser
ccf0fdd02b XPedite5370 board support
Initial support for Extreme Engineering Solutions XPedite5370 -
a MPC8572-based 3U VPX single board computer with a PMC/XMC
site.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-19 18:11:49 -06:00
Michal Simek
8fab49ea91 microblaze: Remove XUPV2P board
---

Microblaze platforms use generic settings and to have
many platforms is confusing that's why I decided to remove this
platform from U-BOOT. ml401 tree is sufficient for covering
all Microblaze platforms.

This change will go through microblaze custodian tree.
2008-12-10 09:25:33 +01:00
Wolfgang Denk
7fa6a2f3b6 MAKEALL: Automatically use parallel builds
Add logic to the MAKEALL script to determine the number of CPU cores
on the system, and run a parallel build if there is more than one.
Usually this significantrly accelerates builds.

Allow to manually adjust the number of parallel make jobs by using
the "BUILD_NCPUS" environment variable.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-09 00:39:08 +01:00
Heiko Schocher
fed36ac5ae powerpc: 83xx: add support for the kmeter1 board
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.

- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-11-20 15:29:32 -06:00
Wolfgang Denk
23b7b87a37 Merge branch 'master' of git://git.denx.de/u-boot-at91 2008-11-09 00:09:51 +01:00
Sergey Lapin
1079432e04 Custom AFEB9260 board support
This patch provides support for AFEB9260 board, a product of
OpenSource hardware and software. Some commertial projects
are made with this design. A board is basically AT91SAM9260-EK
with some modifications and different peripherals and different
parts used. Main purpose of this project is to gain experience in
hardware design.
More info: http://groups.google.com/group/arm9fpga-evolution-board
(In Russian only, sorry).
Subversion repository: svn://194.85.238.22/home/users/george/svn/arm9eb

Signed-off-by: Sergey Lapin <slapin@ossfans.org>
2008-11-04 23:47:17 +01:00
TsiChung Liew
536e7dac16 ColdFire: Add MCF5301x CPU and M53017EVB support
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-11-03 09:45:58 -07:00
Georg Schardt
5deb8022c3 ppc4xx: New board avnet fx12 minimodul
This patch adds support for the avnet fx12 minimodul.
It needs the "ppc4xx: Generic architecture for xilinx ppc405"
patch from Ricardo.

Signed-off-by: Georg Schardt <schardt@team-ctech.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-24 17:34:26 +02:00
Dirk Eibach
d7b26d5832 ppc4xx: Add GDSys neo 405EP board support
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21 17:35:02 +02:00
Adam Graham
f09f09d389 ppc4xx: Add AMCC Arches board support (dual 460GT)
The Arches Evaluation board is based on the AMCC 460GT SoC chip.
This board is a dual processor board with each processor providing
independent resources for Rapid IO, Gigabit Ethernet, and serial
communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR
FLASH, UART, EEPROM and temperature sensor, along with a shared debug
port. The two 460GT's will communicate with each other via shared
memory, Gigabit Ethernet and x1 PCI-Express.

Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21 17:34:46 +02:00
Ricardo Ribalda Delgado
e07f4a8033 ppc44x: Unification of virtex5 pp440 boards
This patch provides an unificated way of handling xilinx v5 ppc440 boards.

It unificates 3 different things:

1) Source code
A new board called ppc440-generic has been created. This board includes
a generic tlb initialization (Maps the whole memory into virtual) and
defines board_pre_init, checkboard, initdram and get_sys_info weakly,
so, they can be replaced by specific functions.

If a new board needs to redefine any of the previous functions
(specific initialization) it can create a new directory with the
specific initializations needed. (see the example ml507 board).

2) Configuration file
Common configurations are located under configs/xilinx-ppc440.h, this
header file interpretes the xparameters file generated by EDK and
configurates u-boot in correspondence. Example: if there is a Temac,
allows CMD_CONFIG_NET
Specific configuration are located under specific configuration file.
(see the example ml507 board)

3) Makefile
Some work has been done in order to not duplicate work in the Main
Makefile. Please see the attached code.

In order to support new boards they can be implemented in the next way:

a) Simple Generic Board  (90% of the time)
Using EDK generates a new xparameters.h file, replace
ppc440-generic/xparameters.h  and run make xilinx-ppc440-generic_config
&& make

b) Simple Boards with special u-boot parameters (9 % of the time)
Create a new file under configs for it (use ml507.h as example) and
change your paramaters. Create a new Makefile paragraph and compile

c) Complex boards (1% of the time)
Create a new folder for the board, like the ml507

Finally, it adds support for the Avnet FX30T Evaluation board, following
the new generic structure:

Cheap board by Avnet for evaluating the Virtex5 FX technology.

This patch adds support for:
 - UartLite
 - 16MB Flash
 - 64MB RAM

Prior using U-boot in this board, read carefully the ERRATA by Avnet
to solve some memory initialization issues.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-05 11:51:22 +02:00
Nick Spence
64ac1eb5af mpc83xx: fix mpc8313 in-tree building with NAND
and add mpc8313 NAND build to MAKEALL

Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-09-03 16:09:52 -05:00
Wolfgang Denk
a13b2d9379 Merge branch 'master' of git://git.denx.de/u-boot-arm 2008-09-01 00:06:05 +02:00
Nobuhiro Iwamatsu
3aeb1ff748 sh: Add support sh2 to MAKEALL
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31 23:08:42 +09:00
Nobuhiro Iwamatsu
6f0da4972e sh: Renesas Solutions AP325RXA board support
AP325RXA is SH7723's reference board.
This has SCIF, NOR Flash, Ethernet, USB host, LCDC, SD Host, Camera and other.
In this patch, support SCIF, NOR Flash, and Ethernet.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31 23:05:41 +09:00
Nobuhiro Iwamatsu
c655fad06b sh: Renesas RSK+ 7203 board support
This adds initial support for the RTE RSK+ SH7203 board.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31 23:02:04 +09:00
Nobuhiro Iwamatsu
0d53a47dc0 sh: Renesas R0P7785LC0011RL board support
This board has SH7785, 512MB DDR2-SDRAM, NOR Flash,
Graphic, Ethernet, USB, SD, RTC, and I2C controller.

This patch supports the following functions:
 - 128MB DDR2-SDRAM (29-bit address mode only)
 - NOR Flash
 - USB host
 - Ethernet

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31 22:45:08 +09:00
Guennadi Liakhovetski
11edcfe260 ARM: Add support for S3C6400 based SMDK6400 board
SMDK6400 can only boot U-Boot from NAND-flash. This patch adds a nand_spl
driver for it too. The board can also boot from the NOR flash, but due to
hardware limitations it can only address 64KiB on it, which is not enough
for U-Boot. Based on the original sources by Samsung for U-Boot 1.1.6.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-08-31 00:39:47 +02:00
Kumar Gala
9490a7f1a9 mpc85xx: Add support for the MPC8536DS reference board
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-27 11:43:54 -05:00
Kumar Gala
129ba616b3 mpc85xx: Add support for the MPC8572DS reference board
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-27 11:43:53 -05:00
Andre Schwarz
306620b762 remove MVS1 board
MVS1 board has reached end-of-life and can be removed completely.

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
2008-08-26 23:58:46 +02:00
Haavard Skinnemoen
d3c23a790f Merge branch 'next' of git://git.denx.de/u-boot-avr32
Conflicts:

	MAINTAINERS
2008-08-20 09:37:09 +02:00
Haavard Skinnemoen
7321d7e7b6 Merge branch 'mimc200' of git://git.denx.de/u-boot-avr32
Conflicts:

	MAKEALL
	Makefile
2008-08-20 09:12:28 +02:00
Mark Jackson
13b50fe3bc avr32: Add MIMC200 board
The MIMC200 board is based on Atmel's NGW100 dev kit, but with an extra
8MByte FLASH and 128KByte FRAM.

Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-20 09:10:31 +02:00
TsiChung Liew
05316f8ece ColdFire: Add M54451EVB platform support for MCF5445x
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-08-14 12:31:56 -06:00
TsiChung Liew
6d33c6acfa ColdFire: Add M5253DEMO platform support for MCF5253
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-08-14 12:30:10 -06:00
Haavard Skinnemoen
7772c13ba0 Merge branch 'favr-32' of git://git.denx.de/u-boot-avr32
Conflicts:

	MAINTAINERS
	MAKEALL
	Makefile
2008-08-06 15:12:38 +02:00
Hans-Christian Egtvedt
0eb5717a85 avr32: add support for EarthLCD Favr-32 board
This patch adds support for the Favr-32 board made by EarthLCD.

This kit, which is also called ezLCD-101 when running with EarthLCD firmware,
has a 10.4" touch screen LCD panel, 16 MB 32-bit SDRAM, 8 MB parallel flash,
Ethernet, audio out, USB device, SD-card slot, USART and various other
connectors for cennecting stuff to SPI, I2C, GPIO, etc.

Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-06 15:10:50 +02:00
Stefan Roese
f2302d4430 Fix merge problems
Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-06 14:05:38 +02:00
Ricardo Ribalda Delgado
01a004313c ppc4xx: ML507: U-Boot in flash and System ACE
This patch allows booting from FLASH the ML507 board by Xilinx.
Previously, U-Boot needed to be loaded from JTAG or a Sytem ACE CF

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-30 11:31:37 +02:00
Julien May
5c374c9ee1 Add support for the hammerhead (AVR32) board
The Hammerhead platform is built around a AVR32 32-bit microcontroller
from Atmel.  It offers versatile peripherals, such as ethernet, usb
device, usb host etc.

The board also incooperates a power supply and is a Power over Ethernet
(PoE) Powered Device (PD).

Additonally, a Cyclone III FPGA from Altera is integrated on the board.
The FPGA is mapped into the 32-bit AVR memory bus. The FPGA offers two
DDR2 SDRAM interfaces, which will cover even the most exceptional need
of memory bandwidth. Together with the onboard video decoder the board
is ready for video processing.

For more information see: http:///www.miromico.com/hammerhead

Signed-off-by: Julien May <mailinglist@miromico.ch>
[haavard.skinnemoen@atmel.com: various small fixes and adaptions]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-07-30 10:06:11 +02:00
Adrian Filipi
7610db17fd Removed support for the adsvix board.
Support for the adsvix was originally provided by Applied Data
Systems (ADS), inc., now EuroTech, Inc.
The board never shipped aside from some sample boards.

Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>
2008-07-30 00:26:03 +02:00
Ricardo Ribalda Delgado
086511fc96 ppc4xx: ML507 Board Support
The Xilinx ML507 Board is a Virtex 5 prototyping board that includes,
	among others:
	-Virtex 5 FX FPGA (With a ppc440x5 in it)
	-256MB of SDRAM2
	-32MB of Flash
	-I2C Eeprom
	-System ACE chip
	-Serial ATA connectors
	-RS232 Level Conversors
	-Ethernet Transceiver

This patch gives support to a standard design produced by EDK for this
board: ppc440, uartlite, xilinx_int and flash

- Includes Changes propossed by Stefan Roese and Michal Simek

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Acked-by: Stefan Roese <sr@denx.de>
2008-07-18 12:31:17 +02:00
Stefan Roese
42246dacf6 Merge branch 'master' of /home/stefan/git/u-boot/u-boot into next 2008-07-17 10:41:06 +02:00
Andre Schwarz
5e0de0e216 mpc5xxx: Add MVBC_P board support
The MVBC_P is a MPC5200B based camera system with Intel Gigabit ethernet
controller (using e1000) and custom Altera Cyclone-II FPGA on PCI.

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-07-15 10:12:58 -06:00
Stefan Roese
4b326101d6 Merge branch 'master' of /home/stefan/git/u-boot/u-boot into next 2008-07-14 10:45:47 +02:00
Wolfgang Denk
0740ac26f4 Merge branch 'master' of git://git.denx.de/u-boot-coldfire 2008-07-13 14:44:04 +02:00
TsiChung Liew
f94945b517 ColdFire: Fix incorrect board name in MAKEALL for M5253EVBE
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-07-11 10:45:58 -06:00
Feng Kan
0ce5c8675b ppc4xx: Initial framework of the AMCC PPC460SX redwood reference board.
Add AMCC Redwood reference board that uses the latest
PPC 464 CPU processor combined with a rich mix of peripheral
controllers. The board will support PCIe, mutiple Gig ethernet
ports, advanced hardware RAID assistance and IEEE 1588.

Signed-off-by: Feng Kan <fkan@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-11 13:18:12 +02:00
Jean-Christophe PLAGNIOL-VILLARD
fdd70d1921 MAKEALL: remove duplicated at91 from ARM9 list and add LIST_at91 to arm
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-07-10 23:01:02 +02:00
Nobuhiro Iwamatsu
9e23fe0560 sh: Fix SH-boards compile error
By Cleanup out-or-tree building for some boards (.depend)
(commit:c8a3b109f07f02342d097b30908965f7261d9f15)
because filse ware changed, some SH-boards have compile error.
I revised this problem.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-07-08 12:03:24 +09:00
Hugo Villeneuve
c7f879ec2b ARM: Add support for Lyrtech SFF-SDR board (ARM926EJS)
This patch adds support for the Lyrtech SFF-SDR board,
based on the TI DaVinci architecture (ARM926EJS).

Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Philip Balister <philip@balister.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-06-28 22:54:21 +02:00
Wolfgang Denk
b77cddc7b5 Merge branch 'master' of git://www.denx.de/git/u-boot-sh 2008-06-11 22:54:47 +02:00
Wolfgang Denk
5ea67393b8 Merge branch 'master' of git://www.denx.de/git/u-boot-mpc85xx
Conflicts:

	include/asm-ppc/fsl_lbc.h

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-06-11 21:33:16 +02:00
Wolfgang Grandegger
1287e0c55a TQM8548: Basic support for the TQM8548 modules
This patch adds basic support for the TQM8548 module from TQ-Components
(http://www.tqc.de/) including DDR2 SDRAM initialisation and support for
eTSEC 3 and 4

Furthermore Flash buffer write has been enabled to speed up output to
the Flash by approx. a factor of 10.

Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2008-06-11 00:01:43 -05:00
Andre Schwarz
a1293e549b add MPC8343 based board mvBlueLYNX-M7 (board+make files)
Add MPC8343 based board mvBlueLYNX-M7.
It's a single board stereo camera system.
Please read doc/README.mvblm7 for details.

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-06-10 13:07:58 -05:00
Nobuhiro Iwamatsu
7faddaecea sh: Renesas Solutions SH7763RDP board support
SH7763RDP has SCIF, NOR Flash, Ethernet, USB host, LCDC and MMC.
In this patch, support SCIF, NOR Flash, and Ethernet.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-06-09 14:23:19 +09:00
Wolfgang Denk
912810eeca Merge remote branch 'u-boot-at91/for-1.3.4' 2008-06-03 00:24:36 +02:00
Wolfgang Denk
7a68389a23 Merge remote branch 'u-boot-avr32/master' 2008-06-03 00:19:57 +02:00
Wolfgang Denk
9d2459f353 Merge remote branch 'u-boot-ppc4xx/master' 2008-06-02 23:28:39 +02:00
Haavard Skinnemoen
0a2e48792d avr32: Add support for the ATSTK1006 board
This is a replacement for ATSTK1002 with 64MB SDRAM and NAND flash on
board. It's currently in production and will be available soon.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-05-27 15:27:29 +02:00
Jean-Christophe PLAGNIOL-VILLARD
602cac1389 MAKEALL: add at91 list
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-24 12:58:36 +02:00
Jean-Christophe PLAGNIOL-VILLARD
42fd5f87b1 Merging Stelian Pop AT91 patches
Merge branch 'testing-V2'

Conflicts:

	board/atmel/at91cap9adk/Makefile
                Fixing copyright
	board/atmel/at91sam9260ek/Makefile
                Fixing copyright
	board/atmel/at91sam9260ek/u-boot.lds
                Delete no more needed ld script

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-24 12:56:53 +02:00
Stefan Roese
97f7d27c8e Merge branch 'quad100hd' 2008-05-21 17:39:24 +02:00
Sergei Poselenov
5d108ac8f4 Initial support for "Socrates" board
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
2008-05-20 23:27:46 +02:00
Wolfgang Denk
a38dc3ea86 TQM8272: fix out-of-tree building
...and add to MAKEALL script

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-15 00:42:45 +02:00
Stelian Pop
2118ebb44d AT91SAM9RLEK support
This patch adds support for the AT91SAM9RL chip and the AT91SAM9RLEK
board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:35:23 +02:00
Stelian Pop
8e429b3eee AT91SAM9263EK support
This patch adds support for the AT91SAM9263 chip and the AT91SAM9263EK
board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:34:29 +02:00
Stelian Pop
d99a8ff66d AT91SAM9261EK support
This patch adds support for the AT91SAM9261 chip and the AT91SAM9261EK
board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:32:08 +02:00
Gary Jennejohn
73ccb3410a ppc4xx: Add the Harris QUAD100HD AMCC 405EP-based board
Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-05-08 16:44:01 +02:00
Wolfgang Denk
12a67a9e51 MAKEALL: add inka4x0 board
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-05 12:52:36 +02:00
Wolfgang Denk
d9a42c0ace MAKEALL: sort entries / lists.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-04-20 15:35:52 -07:00
Guennadi Liakhovetski
b5dc9b304d Support for the MX31ADS evaluation board from Freescale
This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by
Freescale.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-04-18 10:05:14 -07:00
Guennadi Liakhovetski
61525f2ffa Support for LinkStation / KuroBox HD and HG PPC models
This patch is based on the port by Mihai Georgian (see linkstation.c for
Copyright information) and implements support for LinkStation / KuroBox HD
and HG PPC models from Buffalo Technology, whereby HD is deactivated at
the moment, pending network driver fixing.

Notice to users: this is pretty much a barebone port. Support for network
on HG models is already in the U-Boot mainline, but you might also want
patches to switch fan / phy modes depending on the negotiated ethernet
parameters. This patch also doesn't support console switching, booting EM
mode, Buffalo specific ext2 magic number. So, if you want to use any of
those, you need additional patches. Otherwise this patche provides a fully
functional u-boot with a network console on your system.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-04-13 23:08:40 -07:00
Sascha Hauer
5ad862166a Phytec Phycore-i.MX31 support
This patch adds support for the Phytec Phycore-i.MX31 board

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-04-13 14:29:18 -07:00
Sascha Hauer
caebc95be3 mx31 litekit support
This patch adds support for the mx31 litekit board

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-04-13 14:28:24 -07:00
Wolfgang Denk
7cc399c86b Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze 2008-04-13 09:30:26 -07:00
Wolfgang Denk
58a3cbbf24 Merge branch 'master' of git://www.denx.de/git/u-boot-sparc 2008-04-13 09:21:00 -07:00
Wolfgang Denk
950a392464 Revert merge of git://www.denx.de/git/u-boot-arm, commit 62479b18:
Reverting became necessary after it turned out that the patches in
the u-boot-arm repo were modified, and in some cases corrupted.

This reverts the following commits:

	066bebd635
	7a837b7310
	c88ae20580
	a147e56f03
	d6674e0e2a
	8c8463cce4
	c98b47ad24
	8bf69d8178
	8c16cb0d3b
	a574a73852
	1377b5583a
	1704dc2091

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-04-11 15:11:26 +02:00
Michal Simek
f91374f65e microblaze: Sort microblaze boards in MAKEALL script 2008-04-08 15:38:15 +02:00
Daniel Hellstrom
ab68f921d9 SPARC/LEON2: added support for Gaisler simulator GRSIM/TSIM for SPARC/LEON2 targets. See www.gaisler.com for information.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
2008-04-08 07:58:33 +00:00
Daniel Hellstrom
6ed8a43a19 SPARC/LEON3: added support for GR-CPCI-AX2000 FPGA AX board. The FPGA is exchangeable but a standard LEON3 design is assumed. See www.gaisler.com for information.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
2008-04-08 07:58:33 +00:00
Daniel Hellstrom
6940383d9e SPARC/LEON3: added support for Altera NIOS Development kit (STRATIX II Edition) with GRLIB template design. See www.gaisler.com for information.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
2008-04-08 07:58:32 +00:00
Daniel Hellstrom
823edd8a66 SPARC/LEON3: added support for Gaisler GRSIM/TSIM2 SPARC/LEON3 simulatorn. See www.gaisler.com for information.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
2008-04-08 07:58:32 +00:00
Daniel Hellstrom
71d7e4c048 SPARC/LEON3: added support for GR-XC3S-1500 board with GRLIB template design. See www.gaisler.com for board information.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
2008-04-08 07:58:32 +00:00
Daniel Hellstrom
c2f02da21a SPARC: Added generic support for SPARC architecture.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
2008-04-08 07:58:32 +00:00
Wolfgang Denk
a1b215e2a2 Merge branch 'master' of git://www.denx.de/git/u-boot-at91 2008-04-08 00:16:36 +02:00
Wolfgang Denk
2c78febd11 Merge branch 'master' of git://www.denx.de/git/u-boot-coldfire 2008-04-08 00:10:17 +02:00
Wolfgang Denk
62479b1814 Merge branch 'master' of git://www.denx.de/git/u-boot-arm 2008-04-08 00:05:42 +02:00
Wolfgang Denk
5c395393cc Merge branch 'master' of git://www.denx.de/git/u-boot-sh 2008-04-08 00:04:39 +02:00
Stelian Pop
0176d43e75 Add support for AT91SAM9260EK
Support for booting from internal DataFlash, external DataFlash card
or NAND flash is available.

Signed-off-by: Stelian Pop <stelian@popies.net>
2008-04-01 01:46:12 +02:00
TsiChung Liew
48ead7a7a9 ColdFire: Remove R5200 board
This board never went into production

Signed-off-by: Zachary P. Landau <zachary.landau@labxtechnologies.com>
Acked-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>
2008-03-31 15:10:24 -06:00
Matthew Fettke
545c8e0a7c ColdFire: Added M5275EVB support.
Signed-off-by: Matthew Fettke <mfettke@videon-central.com>
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>
2008-03-31 15:10:11 -06:00
David Brownell
a3543d6dc5 add missing ARM boards to MAKEALL
Add some missing ARM boards to MAKEALL.  These build correctly,
unlike several of the boards already listed.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2008-03-30 14:09:55 +02:00
Guennadi Liakhovetski
7a837b7310 Support for the MX31ADS evaluation board from Freescale
This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by Freescale.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-03-30 11:32:30 +01:00
Sascha Hauer
c88ae20580 Phytec Phycore-i.MX31 support
This patch adds support for the Phytec Phycore-i.MX31 board

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-03-30 11:32:27 +01:00
Sascha Hauer
a147e56f03 mx31 litekit support
This patch adds support for the mx31 litekit board

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-03-30 11:32:24 +01:00
Peter Pearse
8c16cb0d3b Add pmdra into MAKEALL
Signed-off-by: Peter Pearse <peter.pearse@arm.com>
2008-03-30 11:23:05 +01:00
Nobuhiro Iwamatsu
f5e2466f7b sh: Add support Renesas Solutions R2D plus board
R2D plus is SH reference board used with SH7751R.
This board has 266Mhz CPU, 64MB SDRAM, Cardbus, CF interface,
one PCI bus, VGA, and two Ethernet controller.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-03-28 14:16:13 +09:00
Mark Jonas
3313e0e262 sh: Added support for SH7720 based board MPR2.
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-03-28 14:16:12 +09:00
Yusuke Goda
c133c1fb0b sh: Add support Renesas Solutions R7780MP
Renesas Solutions R7780MP is a reference board on SH7780.
This board has serial, 10/100 base Ethernet deivice, CF slot
and VGA devices. This board can set extension board.
Extension board has 10/100/1000 base Ethernet device, PCI slot,
S-ATA, iDVR slot.

Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-03-28 14:16:12 +09:00
goda.yusuke
c2042f5952 sh: Add support Renesas Solutions Migo-R board
Migo-R is a board based on SH7722 and has may devices.
In this patch, supported SCIF, NOR flash and Ethernet.

Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-03-28 14:16:11 +09:00
Stefan Roese
4c9e855734 ppc4xx: Add AMCC Glacier 406GT eval board support
This patch adds support for the AMCC Glacier 460GT eval board.
The main difference to the Canyonlands board are listed here:

- 4 ethernet ports instead of 2
- no SATA port
- no USB port

Currently EMAC2+3 are not working. This will be fixed in a later
release.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-27 09:54:41 +01:00
Stefan Roese
71665ebf88 ppc4xx: Add Canyonlands NAND booting support
460EX doesn't support a fixed bootstrap option to boot from 512 byte page
NAND devices. The only bootstrap option for NAND booting is option F for
2k page devices. So to boot from a 512 bype page device, the I2C bootstrap
EEPROM needs to be programmed accordingly.

This patch adds basic NAND booting support for the AMCC Canyonlands aval
board and also adds support to the "bootstrap" command, to enable NAND
booting I2C setting.

Tested with 512 byte page NAND device (32MByte) on Canyonlands.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15 07:28:05 +01:00
Stefan Roese
c813f1f835 ppc4xx: Add AMCC Canyonlands support (460EX) (3/3)
This patch adds support for the AMCC Canyonlands 460EX evaluation
board.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15 07:28:05 +01:00
Niklaus Giger
b05f35436b ppc4xx: Add 405GPr based MCU25 board. Global files
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2008-03-15 07:26:21 +01:00
Peter Pearse
d7d9afa48c Merge branch '080131_artila' of git://linux-arm.org/u-boot-armdev 2008-02-15 12:59:56 +00:00
Peter Pearse
ae92069abe Merge branch '080116_at91cap9' of git://linux-arm.org/u-boot-armdev 2008-02-15 12:59:15 +00:00
Mike Frysinger
208447f8e9 Do not specify a CROSS_COMPILE default when executing size
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-02-14 23:41:40 +01:00