The mvpp2_bm_bufs_add() currently creates a fake cookie by calling
mvpp2_bm_cookie_pool_set(), just to be able to call
mvpp2_pool_refill(). But all what mvpp2_pool_refill() does is extract
the pool ID from the cookie, and call mvpp2_bm_pool_put() with this ID.
Instead of doing this convoluted thing, just call mvpp2_bm_pool_put()
directly, since we have the BM pool ID.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.
This gets rid of the warnings:
CACHE: Misaligned operation at range ...
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit introduces timer driver for ARC.
ARC timers are configured via ARC AUX registers so we use special
functions to access timer control registers.
This driver allows utilization of either timer0 or timer1
depending on which one is available in real hardware. Essentially
only existing timers should be mentioned in board's Device Tree
description.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for fixed link to NETA driver.
This feature requreed for proper support of SFP modules
and onboard connected devices like Ethernet switches
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add ability to use board-specific initialization flow
to NETA driver (for instance Ethernet switch bring-up)
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The USB device should linked to VBUS regulator through "vbus-supply"
DTS property.
This patch adds handling for "vbus-supply" property inside the USB
device entry for turning on the VBUS regulator upon the host adapter probe.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for "marvell,reset-gpio" property to mvebu DW PCIe
driver.
This option is valid when CONFIG_DM_GPIO=y
Change-Id: Ic17c500449050c2fbb700731f1a9ca8b83298986
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
We used to get the address of the optionnal ctrl_mod_mmap register as the
third memory range of the "reg" property. the linux driver moved to use a
syscon instead. In order to keep the DTS as close as possible to that of
linux, we move to using a syscon as well.
If SYSCON is not supported, the driver reverts to the old way of getting
the address from the 3rd memory range
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In the DTS, the addresses are defined relative to the parent bus. We need
to translate them to get the address as seen by the CPU core.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
commit 2f11cd9121 ("dm: core: Handle global_data moving in SPL")
handles relocation of GD in SPL if spl_init() is called before
board_init_r(). So, uclass_root.next need not be initialized always
and accessing uclass_root.next->prev gives an abort. Update the
uclass_root only if it is available.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The Xenon SDHCI driver just missed the integration of this patch:
git ID 6d0e34bf
mmc: sdhci: Distinguish between base clock and maximum peripheral frequency
With this patch applied, the SDHCI subsystem complains now with this warning
while probing:
sdhci_setup_cfg: Hardware doesn't specify base clock frequency
This patch fixes this issue, by providing the missing host->max_clk
variable to the SDHCI subsystem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
It's redundant to send cmd13 after cmd9 whose response is not R1b. The
card devices will not be busy w/ cmd9.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
This patch adds Intel Tangier eMMC/SDHCI driver.
Intel Tangier SoC contains a hybrid of PCI and non-PCI devices. SDHCI
controller is one of the devices which are *not* on a PCI and, hence,
cannot be enumerated by standard PCI means. This driver, allows for
SDHCI controller on Tangier SoC to work in U-Boot.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't want pci_mmc to compile every time x86 compiles, only when
there's a platform that needs it. For that reason, we're adding a new
CONFIG_MMC_PCI which platforms can choose to enable.
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This patch fixup iommu-map property on pci node to have a valid
mapping of requester-id to stream-id. The requester-id to stream-id
mapping is based on PCI-LUT table initialization.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Layerscape Chasis-2 also uses same PCIe controller as Chasis-3
and have similar PCI-Lut.
Signed-off-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add nand_size() function to move the nand size print into initr_nand().
Remove nand size print from nand_init() to allow other function to call
nand_init() without printing nand size.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add initialization flag to avoid initializing NAND Flash multiple
times, otherwise it will calculate a wrong total size.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2088A and its variants have different PCIe node than LS2080A.
The compatible string is updated accordingly.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS2088A series SoCs has different physical memory map address and
CCSR registers address against LS2080A series SoCs.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SOC’s like LS1012A has only one chip select signal for QSPI flash.
Avoid scanning other flash.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MAC number used per QSGMII is not fixed. It may wary from SoC to SoC.
So move QSGMII wriop_init_dpmac() to SoC file.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In EP mode, to enable accesses from the Root Complex, the
CONFIG_READY bit must be set, otherwise any config attempts
from the Root Complex will be returned with config retry
status (CRS).
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch allows using i2c commands (e.g. "i2c probe", "i2c md", etc)
without the need to first select the bus number with e.g. "i2c dev 0".
This is the "i2c" command behavior similar to the one from pre DM, where
by default bus 0 was immediately accessible.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch updates the way in which psc, sscl and ssch I2C parameters are
calculated to be in sync with v4.9 Linux kernel
SHA1: 69973b830859bc6529a7a0468ba0d80ee5117826
in the ./drivers/i2c/busses/i2c-omap.c
The previous method was causing several issues:
- The internal I2C frequency (after prescaler) was far above recommended
one (7 - 12 MHz [*]) - the current approach brings better noise suppression
(as stated in Linux commit: SHA1: 84bf2c868f3ca996e5bb)
- The values calculated (psc, sscl and ssch) were far from optimal, which
caused on the test platform (AM57xx) the I2C0 SCL signal low time (Fast
Mode) of ~1.0us (the standard requires > 1.3 us).
[*] for AM57xx TRM SPRUHZ6G, Table 24,7
"HS I2C Register Values for Maximum I2C Bit Rates in I2C F/S, I2C HS Modes"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
v4.9 Linux release:
SHA1: 69973b830859bc6529a7a0468ba0d80ee5117826
in the ./drivers/i2c/busses/i2c-omap.c
recommends to use SCLH=5 and SCLL=7 values.
This patch sets them to default.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Normally, this would probably be done by adding devicetree aliases
to the main dtsi file for the lpc32xx and using bus->req_seq instead.
Since we want to have consistent i2c numbering, we cannot force the
bus->req_seq because. If for instance we have 3 buses numbered
from 0 to 2 with i2c0 enabled, i2c1 disabled and i2c2 enabled;
i2c2 can be selected using 'i2c dev 1' and 'i2c dev 2' commands
because a bus can be probed using req_seq or seq interchangeably.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Since the lpc32xx i2c driver does not yet support the devicetree bindings,
this structure is also needed by the board file as the hardware description
is done there.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This is part of the prep work for the migration to the driver model.
It will enable the driver to support DM and non-DM configurations
using the same functions.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This is part of the prep work for the migration to the driver model.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This is part of the prep work for the migration to the driver model.
What used to be the probe function is now called probe_chip.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This patch adds a reset controller implementation for STMicroelectronics
STi family SoCs; it allows a group of related reset like controls found
in multiple system configuration registers to be represented by a single
controller device.
Driver code has been mainly extracted from kernel
drivers/reset/sti/reset-stih407.c
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In the description of function pci_match_one_id(), there are some
problems on arguments list and return value description, so correct
them.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is sometimes convenient to know how many and/or which resources are
currently loaded into a TPG, e.g. to test is a flush operation succeeded.
Hence, we add a command that lists the resources of a given type currently
loaded into the TPM.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
If we want to load a key into a TPM, we need to know the designated parent
key's handle, so that the TPM is able to insert the key at the correct place in
the key hierarchy.
However, if we want to load a key whose designated parent key we also
previously loaded ourselves, we first need to memorize this parent key's handle
(since the handles for the key are chosen at random when they are inserted into
the TPM). If we are, however, unable to do so, for example if the parent key is
loaded into the TPM during production, and its child key during the actual
boot, we must find a different mechanism to identify the parent key.
To solve this problem, we add a function that allows U-Boot to load a key into
the TPM using their designated parent key's SHA1 hash, and the corresponding
auth data.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).
For this purpose we introduce a new phy-driver, called "Fixed PHY".
Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.
Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).
During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Fixed cache misaligned issue in the net driver. The issue shows-up when
a call to flush_dcache_range is made with unaligned memory. The memory
must be aligned to ARCH_DMA_MINALIGN.
Signed-off-by: Suji Velupillai <suji.velupillai@broadcom.com>
Tested-by: Suji Velupillai <suji.velupillai@broadcom.com>
Reviewed-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Shamez Kurji <shamez.kurji@broadcom.com>
Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Cover Letter:
This series resolves issues specific to the Broadcom SF2 driver:
- fix cache misaligned issue
- convert to Kconfig
END
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently the mac address is programmed directly in _sunxi_emac_eth_init
making it a one time inflexible operation. By moving it into a separate
function, we can now use this more flexibly.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This replaces legacy arch/arc/lib/timer.c implementation and allows us
to describe ARC Timers in Device Tree. Among other things that way we
may properly inherit Timer's clock from CPU's clock s they really run
synchronously.
This commit introduces timer driver for ARC.
ARC timers are configured via ARC AUX registers so we use special
functions to access timer control registers.
This driver allows utilization of either timer0 or timer1
depending on which one is available in real hardware. Essentially
only existing timers should be mentioned in board's Device Tree
description.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for fixed link to NETA driver.
This feature requreed for proper support of SFP modules
and onboard connected devices like Ethernet switches
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add ability to use board-specific initialization flow
to NETA driver (for instance Ethernet switch bring-up)
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The USB device should linked to VBUS regulator through "vbus-supply"
DTS property.
This patch adds handling for "vbus-supply" property inside the USB
device entry for turning on the VBUS regulator upon the host adapter probe.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for "marvell,reset-gpio" property to mvebu DW PCIe
driver.
This option is valid when CONFIG_DM_GPIO=y
Change-Id: Ic17c500449050c2fbb700731f1a9ca8b83298986
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
We used to get the address of the optionnal ctrl_mod_mmap register as the
third memory range of the "reg" property. the linux driver moved to use a
syscon instead. In order to keep the DTS as close as possible to that of
linux, we move to using a syscon as well.
If SYSCON is not supported, the driver reverts to the old way of getting
the address from the 3rd memory range
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In the DTS, the addresses are defined relative to the parent bus. We need
to translate them to get the address as seen by the CPU core.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
commit 2f11cd9121 ("dm: core: Handle global_data moving in SPL")
handles relocation of GD in SPL if spl_init() is called before
board_init_r(). So, uclass_root.next need not be initialized always
and accessing uclass_root.next->prev gives an abort. Update the
uclass_root only if it is available.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The Xenon SDHCI driver just missed the integration of this patch:
git ID 6d0e34bf
mmc: sdhci: Distinguish between base clock and maximum peripheral frequency
With this patch applied, the SDHCI subsystem complains now with this warning
while probing:
sdhci_setup_cfg: Hardware doesn't specify base clock frequency
This patch fixes this issue, by providing the missing host->max_clk
variable to the SDHCI subsystem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
It's redundant to send cmd13 after cmd9 whose response is not R1b. The
card devices will not be busy w/ cmd9.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
This patch adds Intel Tangier eMMC/SDHCI driver.
Intel Tangier SoC contains a hybrid of PCI and non-PCI devices. SDHCI
controller is one of the devices which are *not* on a PCI and, hence,
cannot be enumerated by standard PCI means. This driver, allows for
SDHCI controller on Tangier SoC to work in U-Boot.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't want pci_mmc to compile every time x86 compiles, only when
there's a platform that needs it. For that reason, we're adding a new
CONFIG_MMC_PCI which platforms can choose to enable.
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Move this in to Kconfig with a default of 115200.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang. Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
This driver uses the same pin control binding as that of linux, binding
document of this patch is copied from linux. One addition done is for
GPIO input and output mode configuration which was missing.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Before clock driver availability it was required to enable usart1 clock
for serial init but now with clock driver is taking care of usart1 clock.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
add basic clock driver support for stm32f7 to enable clocks required by
the peripherals.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds device tree support for stm32f7 serial driver & removes serial
platform data structure.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add compatible property for i.MX7ULP.
Add a weak init_usdhc_clk function, i.MX7ULP use this to init the clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add i.MX7ULP support.
The buadrate calculation on i.MX7ULP is different,so add a new setbrg
function for i.MX7ULP.
Add a enum lpuart_devtype for runtime check for different platforms.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@nxp.com>
Cc: Alison Wang <b18965@freescale.com>
Drop CONFIG_LPUART_32B_REG.
Move the register structure to a common file include/fsl_lpuart.h
Define lpuart_serial_platdata structure which includes the reg base and flags.
For 32Bit register access, use lpuart_read32/lpuart_write32 which handles
big/little endian.
For 8Bit register access, still use the orignal code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@nxp.com>
Cc: Alison Wang <b18965@freescale.com>
Add lpi2c driver for i.MX7ULP.
Need to enable the two options to use this driver:
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_IMX_LPI2C=y
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX7ULP pinctrl driver.
Select CONFIG_PINCTRL_IMX7ULP to use this driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by : Stefano Babic <sbabic@denx.de>
This driver implements the HW WATCHDOG functions. Which needs
to set CONFIG_HW_WATCHDOG to use them. This is disabled by default for
mx7ulp.
Use watchdog for reset cpu. Implement this in the driver.
Need to define CONFIG_ULP_WATCHDOG to build it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update the mxc_ocotp driver to support i.MX7ULP.
The read/write sequence has some changes due to
PDN and OUT_STATUS registers added and TIME register is
removed. Also update the bank size and number.
Add is_mx7ulp macro in sys_proto.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add the imx_rgpio2p driver for Rapid GPIO2P controllers on i.MX7ULP.
Have added all ports on RGPIO2P_0 and RGPIO2P_1.
The configurations CONFIG_IMX_RGPIO2P and CONFIG_DM_GPIO must be set
to y to enable the drivers.
To use the GPIO function, the IBE and OBE needs to set in IOMUXC.
We did not set the bits in driver, but leave them to IOMUXC settings
of the GPIO pins. User should use IMX_GPIO_NR to generate the GPIO number
for gpio APIs access.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Despite the comment in the code, CSC unit is never used. According to
the only public description of DW HDMI controller (i.MX6 manual), CSC
unit is bypassed in MC_FLOWCTRL register and then actually powered
down in MC_CLKDIS register.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Function hdmi_lookup_n_cts() is feed with clock in Hz, which gets
compared with clocks in kHz. Fix that by converting all clocks to Hz.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documentation says that we're returning true/false, not 1/0 so adapt
the function to return actual booleans.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Add rk3328 pinctrl driver and grf/iomux structure definition.
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a driver for setting up and modifying the various PLLs and peripheral
clocks on the RK3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Driver for the sysreset of Rockchip rk3188 socs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Add a driver which supports pin multiplexing setup for the most commonly
used peripherals.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Add necessary structs to have the driver also work for the serial
on the rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
The gpll and cpll init values are only used in rk_clk_init in the SPL
and therefore produce compile time warnings in regular uboot builds.
Fix that with an #ifdef.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
Right now the u-boot,dm-pre-reloc flag will make each marked node
always appear in both spl and tpl. But systems needing an additional
tpl might have special constraints for each, like the spl needing to
be very tiny.
So introduce two additional flags to mark nodes for only spl or tpl
environments and introduce a function dm_fdt_pre_reloc to automate
the necessary checks in code instances checking for pre-relocation
flags.
The behaviour of the original flag stays untouched and still marks
a node for both spl and tpl.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Do not use the API which of-platdata not support.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
Change some API in order to enable of-platdata.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
rk3399 grf register bit defenitions should locate in header
file, so that not only pinctrl can use it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
- Move to DM clk driver
- Add clk support for zynq_sdhci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAljKWVcACgkQykllyylKDCEsgACfey0mgRaGVMLSxMMCGgJQIK70
/oYAn3raqYrJ2e2fsjb1B5WodYcDe8L5
=JYC5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2017.05' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2017.05
- Move to DM clk driver
- Add clk support for zynq_sdhci
This device tree has been extracted from v4.9 kernel
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add SDHCI host controller found on STMicroelectronics SoCs
On some ST SoCs, i.e. STiH407/STiH410, the MMC devices can live
inside a dedicated flashSS sub-system that provides an extend subset
of registers that can be used to configure the Arasan MMC/SD Host
Controller.
This means, that the SDHCI Arasan Controller can be configured to be
eMMC4.5 or 4.3 spec compliant.
W/o these settings the SDHCI will configure and use the MMC/SD
controller with limited features e.g. PIO mode, no DMA, no HS etc.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch adds support to ASC (asynchronous serial controller)
driver, which is basically a standard serial driver. This IP
is common across other STMicroelectronics SoCs
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since the reserved RAM is tracked by gd->arch.resv_ram, calculation
of MC memory blocks can be simplified. The MC RAM is guaranteed to be
aligned by the reservation process.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
The execution flow is currently like this for aldo_num == 1 or 2:
int axp_set_aldo(int aldo_num, unsigned int mvolt)
{
...
if (mvolt == 0)
return pmic_bus_clrbits(AXP809_OUTPUT_CTRL1,
AXP809_OUTPUT_CTRL1_ALDO1_EN << (aldo_num - 1));
...
return pmic_bus_clrbits(AXP809_OUTPUT_CTRL1,
AXP809_OUTPUT_CTRL1_ALDO1_EN << (aldo_num - 1));
}
I.e. aldo1 and aldo2 will always be disabled. This patch fixes it by
setting (rather than clearing) the enable bit when mvolt != 0.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Fixes: 795857df41 ("sunxi: power: add AXP809 support")
"unsigned long" is a lousy data type when it comes to match peripheral
hardware registers with a fixed size.
Just do the obvious and match a 32-bit display format with an "u32"
data type for casting.
This fixes the logo display on 64-bit architectures, which produced
a black line on the right side of the logo with non-black backgrounds.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When the zynq_gem driver initializes the phy it sets the supported
features that the phy can support and advertise. However instead of
masking the supported features such that it limits the available
features it sets the phy to have the exact supported features of the
zynq_gem. This is problematic as it will enable features that a phy does
not have or cannot advertise.
Specifically this appears as an issue when using a phy that is only
capable of 10/100, but the zynq_gem driver will override this and try to
enable and advertise 10/100/1000.
Reported-by: Arno Steffens <star@gmx.li>
Fixes: 80243528ef ("net: gem: Fix gem driver on 1Gbps LAN")
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Tested-by: Arno Steffens <star@gmx.li>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
For the boards such as smartweb on which the clock driver isn't
supported, the ethernet fail to be found when booting up with
the below log.
---8<---
Net: No ethernet found.
--->8---
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With this patch, USB Command Verifier is happy with our DFU
implementation on Chapter 9 tests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of only copying if strlen(s) is less than 32 characters, let's
just copy at most 31 characters regardless of the size of
serial#. This will guarantee that we always have a serial number if
serial# environment variable is set to anything.
Note that without a proper serial number, USB Command Verifier fails
our test of Device Descriptor since we will claim to have a serial
number without really providing one when requested.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If last packet is short, we shouldn't write req->length bytes to
non-volatile media, we should write only what's available to us, which
is held in req->actual.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
harmonize result with other handle_XXX() functions: return int for size
remove the define RET_STAT_LEN : no more necessary
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
return the correct size for DFU_GETSTATE result (1 byte in DFU 1.1 spec)
to avoid issue in USB protocol and the variable "value" is propagated
to req->lenght as all the in the other request with answer
- DFU_GETSTATUS
- DFU_DNLOAD
- DFU_UPLOAD
Then the buffer is correctly treated in USB driver
NB: it was the only request witch directly change "req->actual"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
The "DFU descriptor set" must contain the "DFU functional descriptor"
but it is missing today in U-Boot code
(cf: DFU spec 1.1, chapter 4.2 DFU Mode Descriptor Set)
This patch only allocate buffer and copy DFU functional descriptor
after interfaces.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Remove sys_proto.h inclusion which is not used by the driver.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Support the following DT properties:
"bias-disable"
"bias-pull-up"
"bias-pull-down"
"bias-pull-pin-default"
"input-enable"
"input-disable"
My main motivation is to support pull up/down biasing. For Pro5 and
later SoCs, the pupdctrl register number is the same as the pinmux
number, so this feature can be supported without having big pin
tables.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently the system hangs when the 'videomode' variable is not present
and a reset command is issued:
=> setenv videomode
=> saveenv
=> reset
(Board hangs)
lcdif_power_down() assumes that the LCDIF controller has been properly
configured and enabled, which may not be true.
To fix this issue check whether panel.frameAdrs has been initialized and
in case it has not been initialized, do not continue with the LCDIF
powerdown sequence.
Tested on a imx7dsabresd board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
The i.MX7 has the same GPMI controller as i.MX6 and is covered by the MXS
driver. Tell Kconfig that we can use this driver on the MX7 platform (the MXS
driver already has the few i.MX7-specific changes needed for basic operation
and the board itself sets the pinmux correctly).
Tested on i.MX7D with the Sabre board and a NAND Flash soldered to U12.
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
With gcc-6.x we see:
drivers/i2c/fsl_i2c.c:86:3: warning: ‘fsl_i2c_speed_map’ defined but not
used [-Wunused-const-variable=]
The easy way to fix this is that since we only use fsl_i2c_speed_map at
all on __M68K__ move the existing guards around slightly.
Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
The maximum supported peripheral clock frequency of the zynq depends on
the IO routing. The MIO and EMIO support a maximum frequency of 50 MHz
respectively 25 MHz. Use the max-frequency value of the device tree to
determine the maximal supported peripheral clock frequency.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The zynq_sdhci controller driver use CONFIG_ZYNQ_SDHCI_MAX_FREQ as base
clock frequency but this clock is not fixed and depends on the hardware
configuration. Additionally the value of CONFIG_ZYNQ_SDHCI_MAX_FREQ
doesn't match the real base clock frequency of SDIO_FREQ. Use the clock
framework to determine the frequency at run time.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the optional ethernet emio clock source to the zynq
clock framework driver.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move the zynq to clock framework and remove unused functions as well as
the CONFIG_ZYNQ_PS_CLK_FREQ configuration.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a clock framework driver for the zynq platform. The driver is based
on the platform zynq clock driver but reworked to use static functions
instead of run-time generated objects even for unused clocks.
Additionally the CONFIG_ZYNQ_PS_CLK_FREQ is replaced by the
ps-clk-frequency from the device tree.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If available use the clock framework to set the tx clock rate of the
zynq ethernet controller.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The gem[0-1]_rclk_ctrl registers control the source of the rx clock,
control and data signals and configure via ps7_init function. Don't
overwrite the register with the default value.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With the Kconfig re-sync with Linux 4.10, characters such as
'}', ';' in Kconfig help message cause warnings:
$ make defconfig
*** Default configuration is based on 'sandbox_defconfig'
drivers/i2c/Kconfig:132:warning: ignoring unsupported character '}'
drivers/i2c/Kconfig:132:warning: ignoring unsupported character ';'
Drop the Device Tree fragment from the help.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.
During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.
This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.
[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'
[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'
[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
It was incorrect to always include "asm/arch-omap3/mux.h" constantly.
This introduced warnings on non-omap3 where certain values will conflict
between the various families. Conditionally guard the inclusion in
order to correct the problem.
Fixes: 6aca17c9b7 ("drivers: mmc: omap_hsmmc: Fix IO Buffer on OMAP36xx")
Signed-off-by: Tom Rini <trini@konsulko.com>
MMC devices accessed exclusively via the driver model were not
being initialized before being exposed as block devices, causing
issues in scenarios where the MMC device is first accessed via the
uclass block interface.
Signed-off-by: Fiach Antaw <fiach.antaw@uqconnect.edu.au>
On the OMAP36xx/37xx the CONTROL_WKUP_CTRL register has
a field (bit 6) named GPIO_IO_PWRDNZ. If 0, the IO buffers which
are related to GPIO_126, 127 and 129 are disabled. Some boards may
need this for MMC. After the PBIAS is configured, this bit should
be set high to enable these GPIO pins.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
ftsdc021_sdhci.c is dead file.
There is no reason to maintain this host controller.
Removes the entire ftsdc021_sdhci.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If there are alias nodes as "mmc", use the devnum as alias index
number.
This patch is for fixing a problem of Exynos4 series.
Problem is the below thing.
Current legacy mode:
EXYNOS DWMMC: 0, SAMSUNG SDHCI: 1
After using DM:
SAMSUNG SDHCI: 0, EXYNOS DWMMC: 1
Dev index is swapped.
Then u-boot can't find the kernel image..because it is already set to 0 as mmcdev.
If change from legacy to DM, also needs to touch all exynos4 config file.
For using simply, just supporting the fixed devnum with alias node is better than it.
Usage:
alaise {
....
mmc0 = &sdhci2; /* eMMC */
mmc1 = &sdhci1; /* SD */
...
}
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the max8997 controller for Driver model.
Exynos4210 is using max8997 pmic controller.
(pmic_max8997.c should be deprecated.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The array indices used currently are dispalaced by 1 for
SMPS6 through SMPS10 in the respective places of voltage and ctrl
arrays hence fix the same as to assign the right voltage and ctrl
registers.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Both CONFIG_PWM_TEGRA and CONFIG_PWM_EXYNOS depend on CONFIG_DM_PWM,
i.e. they are already guarded by Kconfig correctly. Remove unneeded
ifdef CONFIG_DM_PWM ... endif.
While we are here, let's tidy up alignment and sort the lines
alphabetically in Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
cpsw driver tries to get macid for am43xx SoCs using the compatible
ti,am4372. But not all variants of am43x uses this complatible like
epos evm uses ti,am438x. So use a generic compatible ti,am43 to get
macid for all am43 based platforms.
Tested-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fix H-PLL and M-PLL rate calculation in ast2500 clock driver.
Without this fix, valid setting can lead to division by zero
when requesting the rate of H-PLL or M-PLL clocks.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for version 3 of the ec protocol. It basically works by
stitching some additional header in front (special command code),
and having a result and packet_length stitched on for the reply.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: u-boot@lists.denx.de
Acked-by: Simon Glass <sjg@chromium.org>
Tested on snow:
Tested-by: Simon Glass <sjg@chromium.org>
Just do nothing in post_bind if of-platdata enabled,
for there is no dm_scan_fdt_dev().
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fixed subject line typo:
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Replace dm_i2c_write() / dm_i2c_read() with transaction using
struct i2c_msg[2] in order to allow for i2c controller to detect
write/read cycle to emit a repeated start condition.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: u-boot@lists.denx.de
Acked-by: Simon Glass <sjg@chromium.org>
Tested on snow:
Tested-by: Simon Glass <sjg@chromium.org>
Provide the necessary Kconfig symbols so that PHYLIB support may be
enabled in Kconfig, as opposed to needing to #define these symbols in
C source headers.
BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as
they don't seem to explicitly depend on it (i.e. they do not use the
phy_driver class).
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Modifying content of dev->name leads to the device tree corruption
because it points to the node name located there.
Signed-off-by: Daniel Strnad <strnadda@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In Uboot for Meson GX the compatible string in meson-gxbb.dtsi so far is:
compatible = "amlogic,meson6-dwmac", "snps,dwmac";
On Linux in the same dt file it's
compatible = "amlogic,meson-gx-dwmac", "amlogic,meson-gxbb-dwmac", "snps,dwmac";
To avoid breaking ethernet with the next DT synch from Linux to U-Boot
(planned as prerequisite for adding Meson GX MMC driver to U-Boot) add
"amlogic,meson-gx-dwmac" to the compatibility list in the designware
driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for programmable MAC impedance configuration and
fix typo in DT impedance parameters names.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 79e86ccb37 "vitesse: remove duplicated
argument to ||" correctly removed a redundant check.
However, I believe that the original code was simply wrong, and should have
been checking against RGMII_ID.
To fix this and avoid similar problems in the future, use the
phy_interface_is_rgmii helper function.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This device also works with the 88E1518 code, so we just adjust
the UID mask accordingly.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The mask for the 88E1510 meant that the 88E1518 code would never be
used.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There is code that is specifically for RGMII_TXID interface, but this
will never get used because the code checks that the RGMII interface
is RGMII_ID to RGMII_RXID; RGMII_TXID is after this.
To fix this and avoid similar problems in the future, use the
phy_interface_is_rgmii helper function.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Remove the redundant #ifdef CONFIG_DM_ETH/#endif.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Due to introducing the at91 clock driver, add the clock support.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some files are missing this declaration. Add it to avoid build errors when
we actually need the declaration.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We should use unsigned long rather than u32 for addresses. Update this so
that the table-generation code builds correctly on 64-bit machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add an option for building Platorm Controller Hub drivers in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new Kconfig option to allow timer drivers to be used in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new Kconfig option to allow RTC drivers to be used in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new Kconfig option to allow PCI drivers to be used in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new Kconfig option to allow CPU drivers to be used in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds a function to the TPM library, which allows U-Boot to
flush resources, e.g. keys, from the TPM.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for Marvell 88E1680 Integrated Octal
10/100/1000 Mbps Energy Efficient Ethernet Transceiver.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Armada 38x has four PCI ports, not three.
The optimization in pci_init_board() seems to assume that every port has
three lanes. This is obviously wrong, and breaks support for Armada 38x.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Now that the SD/SDIO/MMC DT properties are updated in the Marvell
A3700 and A7/8k DT files, we need to match the checks for compatible
node in the PHY driver as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fixup port_mac_address property in MC DPC with values from the u-boot
environment. Since u-boot already reads the environment MAC addresses
when probing the PHYs, use these values.
The u-boot environment MAC addresses take precedence over any eventual
ones defined in the DPC, except for the case where they are randomly
assigned (no u-boot env value declared for port).
The patch assumes the "/board_info/ports/" node is present in the DPC.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[York S: Fix several indentations]
Reviewed-by: York Sun <york.sun@nxp.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_AT91".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_ROCKCHIP".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_ZYNQ || ARCH_ZYNQMP".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[1] Rename CONFIG_SANDBOX_MMC to CONFIG_MMC_SANDBOX for consistency
I want all MMC driver options prefixed with CONFIG_MMC_.
[2] Fix dependency
Add necessary depends on to avoid compile error.
Instead "depends on MMC" is unneeded because this config entry
resides inside of "if MMC".
[3] Currently, this config symbol is not referenced at all.
Use it to enable/disable the driver in Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.
Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig. Almost all
of the defines will go away.
I see only two exceptions:
configs/blanche_defconfig
configs/sandbox_noblk_defconfig
They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something
might be wrong with these two boards, so should be checked later.
Anyway, this is the output of the moveconfig tool.
This commit was created as follows:
[1] create a config entry in drivers/mmc/Kconfig
[2] tools/moveconfig.py -r HEAD GENERIC_MMC
[3] manual clean-up of garbage comments in doc/README.* and
include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The readl_poll_timeout() is a useful helper to poll registers
and error out if the condition is not met.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds support for SMSC LAN8742 in phylib
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds glue code required for enabling the designware
mac on stm32f7 devices.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Clock Driver
This driver is ast2500-specific and is not compatible with earlier
versions of this chip. The differences are not that big, but they are
in somewhat random places, so making it compatible with ast2400 is not
worth the effort at the moment.
SDRAM MC driver
The driver is very ast2500-specific and is completely incompatible
with previous versions of the chip.
The memory controller is very poorly documented by Aspeed in the
datasheet, with any mention of the whole range of registers missing. The
initialization procedure has been basically taken from Aspeed SDK, where
it is implemented in assembly. Here it is rewritten in C, with very limited
understanding of what exactly it is doing.
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Watchdog Timer, which is compatible with AST2400 and
AST2500 watchdogs. There is no uclass for Watchdog yet, so the driver
does not follow the driver model. It also uses fixed clock, so no clock
driver is needed.
Add support for timer for Aspeed ast2400/ast2500 devices.
The driver actually controls several devices, but because all devices
share the same Control Register, it is somewhat difficult to completely
decouple them. Since only one timer is needed at the moment, this should
be OK. The timer uses fixed clock, so does not rely on a clock driver.
Add sysreset driver, which uses watchdog timer to do resets and particular
watchdog device to use is hardcoded (0)
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver implementes platform specific code for the Xenon SDHCI
controller which is integrated in the Marvell MVEBU Armada 37xx and
Armada 7k / 8K SoCs.
History:
This driver is ported from the Marvell U-Boot version 2015.01 which is
written by Victor Gu <xigu@marvell.com> with minor changes ported from
the Linux driver which is written by Ziji Hu <huziji@marvell.com>.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Some SDHCI drivers might need to do some special controller configuration
after the common clock set_ios() function has been called (speed / width
configuration). This patch adds a call to the newly created function
set_ios_port() when its configured in the host driver.
This will be used by the Xenon SDHCI controller driver used on the
Marvell Armada 3700 and 7k/8k ARM64 SoCs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch completely clears the SDHCI_CLOCK_CONTROL register before the
new value is configured instead of just clearing the 2 bits
SDHCI_CLOCK_CARD_EN and SDHCI_CLOCK_INT_EN. Without this change, some
clock configurations will lead to the "Internal clock never stabilised."
error message on the Xenon SDHCI controller used on the Marvell Armada
3700 and 7k/8k ARM64 SoCs.
The Linux SDHCI core driver also writes 0 to this register before
the new value is configured. So this patch simplifies the driver a bit
and brings the U-Boot driver more in-line with the Linux one.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The read-only-write-enable bit is set by default and must be cleared
to prevent overwriting read-only registers. This should be done
immediately after resetting the PCI Express controller.
Reviewed-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
[York S: Move SYS_FSL_ERRATUM_A007815 to Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
Print the error code for non-zero (failure case) instead
of making debug statement without any condition, this
usually gives proper clue in failure condition.
Log:
The sdhci controller assumes that the base clock frequency is fully supported by
the peripheral and doesn't support hardware limitations. The Linux kernel
distinguishes between base clock (max_clk) of the host controller and maximum
frequency (f_max) of the card interface. Use the same differentiation and allow
the platform to constrain the peripheral interface.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.
TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Move all of the status LED feature to drivers/led/Kconfig.
doc/README.LED updated to reflect the Kconfig implementation.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
commit: 65f83802b7 "serial: 16550: Add getfcr accessor"
breaks u-boot commandline working with long commands
sending to the board.
Since the above patch, you have to setup the fcr register.
For board/archs which enable OF_PLATDATA, the new field
fcr in struct ns16550_platdata is not filled with a
default value ...
This leads in not setting up the uarts fifo, which ends
in problems, when you send long commands to u-boots
commandline.
Detected this issue with automated tbot tests on am335x
based shc board.
The error does not popup, if you type commands. You need
to copy&paste a long command to u-boots commandshell
(or send a long command with tbot)
Possible boards/plattforms with problems:
./arch/arm/cpu/arm926ejs/lpc32xx/devices.c
./arch/arm/mach-tegra/board.c
./board/overo/overo.c
./board/quipos/cairo/cairo.c
./board/logicpd/omap3som/omap3logic.c
./board/logicpd/zoom1/zoom1.c
./board/timll/devkit8000/devkit8000.c
./board/lg/sniper/sniper.c
./board/ti/beagle/beagle.c
./drivers/serial/serial_rockchip.c
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move fdt fixup of 'status' property into a weak function. This allows
board to define 'status' fdt fixup by themselves.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds a simple pmic driver for the mc34vr500 pmic which
is used in conjunction with the fsl T1 and LS1 series SoC.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch is to add 'fsl,esdhc' into of_match table to support
driver model for QorIQ eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
There would be compiling error as below when enable driver model for esdhc.
undefined reference to `dm_gpio_get_value'
undefined reference to `gpio_request_by_name_nodev'
This patch is to make GPIO support optional with CONFIG_DM_GPIO. Because
all boards of QorIQ platform don't need it and they just check register for
CD/WP status, only some boards of i.MX platform require this.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: York Sun <york.sun@nxp.com>
All Layerscape SoCs have supported new PCIe driver based on DM.
The lagecy PCIe driver code is unused and can be removed.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
There are more than five kinds of Layerscape SoCs. unfortunately,
PCIe controller of each SoC is a little bit different. In order
to avoid too many macro definitions, the patch addes a new
implementation of PCIe driver based on DM. PCIe dts node is
used to describe the difference.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
To make the layerscape pcie driver clear, move the kernel DT fixup
code from pcie_layerscape.c to pcie_layerscape_fixup.c.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
There may be multiple PCIe controllers in a SoC.
It is not correct that always calling pci_bus_to_hose(0) to get
the first PCIe controller for the PCIe device connected other
controllers. We just remove this calling because hose always point
the correct PCIe controller.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
for the legacy PCI driver, the function pci_bus_to_hose() returns
the real PCIe controller. To keep consistency, this function is
changed to return the PCIe controller pointer of the root bus
instead of the current PCIe bus.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The generic probe code in dm works, so get rid of the leftover cruft.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
Revision 1.0 of this IP has a quirk where if during a long read transfer
the transfer_size register will go to 0, the master will send a NACK to
the slave prematurely.
The way to work around this is to reprogram the transfer_size register
mid-transfer when the only the receive fifo is known full, i.e. the I2C
bus is known non-active.
The workaround is based on the implementation in the linux-kernel.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
Reorder the timeout loop such that we first check if the
condition is already true, and then call udelay() so if
the condition is already true, break early.
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
Revision 1.0 of this IP has a couple of issues, such as not supporting
repeated start conditions for read transfers.
So scan through the list of i2c messages for these conditions
and report an error if they are attempted.
This has been fixed for revision 1.4 of the IP, so only report the error
when the IP can really not do it.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
For mux check if the parent is already a device of UCLASS_I2C and if yes
just use that. Otherwise see if someone specified an i2c-parent phandle.
This mimics the behavior found in the Kernel, as it removes the
requirement to explicitly specify a i2c-parent phandle.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
If CONFIG_SYS_I2C_S3C24X0_SLAVE isn't defined, then complie error should
be occurred.
This patch is for preventing it.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Latest gcc 6.2 compiler is throwing the below warning for am335x_baltos_defconfig
drivers/usb/gadget/ether.c:501:17: warning: 'mdlm_detail_desc' defined but not used [-Wunused-const-variable=]
static const u8 mdlm_detail_desc[] = {
Guard mdlm_detail_desc with CONFIG_USB_ETH_SUBSET to avoid the warning
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Drop board_ehci_power when dm usb used and switch to use
regulator api to handle vbus.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Implement ofdata_to_platdata to set the type to host or device.
- Check "dr-mode" property.
- If there is no "dr-mode", check phy_ctrl for i.MX6
and phy_status for i.MX7
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
GCC 6.1 complains about this.
drivers/usb/gadget/dwc2_udc_otg.c:72:19: warning: 'driver_desc'
defined but not used [-Wunused-const-variable=]
static const char driver_desc[] = DRIVER_DESC;
^~~~~~~~~~~
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Dropped becuase
- driver not used any board.
- no dm conversion.
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Richard Retanubun <richardretanubun@ruggedcom.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Acked-by: Angelo Dureghello <angelo@sysam.it>
Unfortunately version 2 of this patch was applied which was missing some
changes. Fix this.
Signed-off-by: Meng Yi <meng.yi@nxp.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Replace hardcoded value with defined constant SECTOR_BYTES.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is no CONFIG_OF_PLATDATA, only CONFIG_SPL_OF_PLATDATA, so rename
the two references to CONFIG_OF_PLATDATA to CONFIG_SPL_OF_PLATDATA.
Signed-off-by: Tom Rini <trini@konsulko.com>
Dropped becuase
- driver and related configs not used any board.
- no dm conversion.
Cc: Heiko Schocher <hs@denx.de>
Cc: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
If the splash file doesn't exist, the booting stops bricking
the boards. Check return value of prepare function and stop
decoding the logo data if splash prepare stage failed.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Commit f401e907fc ("ARM: sunxi: remove bare default for
CONFIG_MMC") dropped "depends on UART0_PORT_F", but it is still
needed. Revive it as a prerequisite of CONFIG_MMC_SUNXI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Until recently, sdhci_ops was used only for overriding IO accessors.
(so, host->ops was not set by any drivers except bcm2835_sdhci.c)
Now, we have more optional callbacks, get_cd, set_control_reg, and
set_clock. However, the code
if (host->ops->get_cd)
host->ops->get_cd(host);
... expects host->ops is set for all drivers.
Commit 5e96217f04 ("mmc: pic32_sdhci: move the code to
pic32_sdhci.c") and commit 62226b6863 ("mmc: sdhci: move the
callback function into sdhci_ops") added sdhci_ops for pic32_sdhci.c
and s5p_sdhci.c, but the other drivers still do not (need not) set
host->ops because all callbacks in sdhci_ops are optional.
host->ops must be checked to avoid the system crash caused by NULL
pointer access.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a new driver for the GMAC ethernet interface present in Rockchip
RK3288 SOCs. This driver subclasses the generic design-ware driver to
add the glue needed specifically for Rockchip.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Export all functions so that drivers can use them, or not, as the need
arises.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With rockchip we need to make adjustments after the link speed is set but
before enabling received/transmit. In preparation for this, split these
two pieces into separate functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
