Before switching to the real Kbuild, drivers/usb/gadget/Makefile
must be fixed.
If none of CONFIG_USB_GADGET, CONFIG_USB_ETHER, CONFIG_USB_DEVICE
is defined, both obj- and obj-y get empty.
We need non-empty obj- or obj-y on each Makefile
to generate built-in.o on the real Kbuild.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
For LPC32XX high-speed UART it is required to send a carriage return
symbol along with line feed. The problem was introduced in e503f90a
commit.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
As mEMAC1 and mEMAC2 are dual-role MACs, which are used as 1G or 10G MAC.
So we update dynamically 'cell-index' to '2' and '3' for 10GEC3 and 10GEC4.
Also change 'fsl,fman-port-1g-rx' to 'fsl,fman-port-10g-rx', ditto for Tx.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
This adds a SPI flash driver which simulates SPI flash clients.
Currently supports the bare min that U-Boot requires: you can
probe, read, erase, and write. Should be easy to extend to make
it behave more exactly like a real SPI flash, but this is good
enough to merge now.
sjg@chromium.org added a README and tidied up code a little.
Added a required map_sysmem() for sandbox.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds a SPI framework for people to hook up simulated SPI clients.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This allows us to put the SPI flash chip inside the SPI interface node,
with U-Boot finding the correct bus and chip select automatically.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch define new names for GPIO pins on at91 devices. Follow up patches
will convert the whole infrastructure to use these new definitions.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Faraday FTSDC021 is a controller which is compliant with
SDHCI v3.0, SDIO v2.0 and MMC v4.3.
However this driver is only verified with SD memory cards.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
CC: Andy Fleming <afleming@gmail.com>
Existing eSDHC SPL framework assumes booting from sd-image
with boot_format header which contains final u-boot Image
offset and size. No such header is present in case of
corenet devices like T1040 as corenet deivces use PBI-RCW
based intialization.
So, for corenet deives, SPL bootloader use values provided
at compilation time. These values can be defined in board
specific config file.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
If platform provides "host->fifoth_val" it will be used for
initialization of DWMCI_FIFOTH register. Otherwise default value will be
used.
This implementation allows:
* escape unclear and recursive calculations that are currently in use
* use whatever custom value for DWMCI_FIFOTH initialization if any
particular SoC requires it
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
dw-mmc.c is the general driver file.
So, remove the exynos specific code at dw-mmc.c.
Instead, exynos specific cod can be move into exynos-dw_mmc.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
In commit bb1f327 we removed the UHH reset to fix NFS root (over usb
ethernet) problems with Beagleboard (3530 ES1.0). However, this
seems to cause USB detection problems for Pandaboard, about (3/8).
On further investigation, it seems that doing the UHH reset is not
the cause of the original Beagleboard problem, but in the way the reset
was done.
This patch adds proper UHH RESET mechanism for OMAP3 and OMAP4/5 based
on the UHH_REVISION register. This should fix the Beagleboard NFS
problem as well as the Pandaboard USB detection problem.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
For invalid bus number, current code returns NULL in the default case of
switch-case statements. In additional, pins[bus] is always not NULL because
it is the address of specific row of the two-dimensional array.
Thus this patch removes these unnecessary test.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
For invalid bus number, current code returns NULL in the default case of
switch-case statements. In additional, pins[bus] is always not NULL because
it is the address of specific row of the two-dimensional array.
Thus this patch removes these unnecessary test.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
This patch adds the U_BOOT_I2C_ADAP_COMPLETE defines for channels
on Exynos5420 and Exynos5250 and also adds support for init function
for hsi2c channels
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Writing zero into I2Ci.I2C_CNT register causes random I2C failures in OMAP3
based devices. This seems to be related to the following advisory which
apears in multiple erratas for OMAP3 SoCs (OMAP35xx, DM37xx), as well as
OMAP4430 TRM:
Advisory:
I2C Module Does Not Allow 0-Byte Data Requests
Details:
When configured as the master, the I2C module does not allow 0-byte data
transfers. Note: Programming I2Ci.I2C_CNT[15:0]: DCOUNT = 0 will cause
undefined behavior.
Workaround(s):
No workaround. Do not use 0-byte data requests.
The writes in question are unnecessary from a functional point of view.
Most of them are done after I/O has finished, and the only one that preceds
I/O (in i2c_probe()) is also unnecessary because a stop bit is sent before
actual data transmission takes place.
Therefore, remove all writes that zero the cnt register.
Cc: Heiko Schocher <hs@denx.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lubomir Popov <lpopov@mm-sol.com>
Cc: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
For a eeprom with a 2-bytes address (e.g., Ateml AT24C1024B),
the r/w address should be serial out in MSB order.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Heiko Schocher <hs@denx.de>
Fix clock value initialisation for Exynos other than Exynos5 for hsi2c.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
This patch adapts the s3c24x0 driver to the new i2c framework.
Config file is modified for all the boards that use the driver.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Heiko Schocher <hs@denx.de>
CC: Inderpal Singh <inderpal.singh@linaro.org>
CC: David Müller <d.mueller@elsoft.ch>
CC: Chander Kashyap <k.chander@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Existing eSPI SPL framework assumes booting from spi-image
with boot_format header which contains final u-boot Image
offset and size. No such header is present in case of
corenet devices like T1040 as corenet deivces use PBI-RCW
based intialization.
So, for corenet deives, SPL bootloader use values provided
at compilation time. These values can be defined in board
specific config file.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
In 48ec5291, only TX path was optimized; this does the same also for RX
path. This results in huge increase of TFTP throughput on custom am3352
board (from 312KiB/s to 1.8MiB/s) and eliminates occasional transfer
timeouts.
Signed-off-by: Vladimir Koutny <vladimir.koutny@streamunlimited.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Tom Rini <trini@ti.com>
Align the ATA ID buffer to the cache-line boundary. This gets rid
of the below error mesages on ARM v7 platforms.
scanning bus for devices...
ERROR: v7_dcache_inval_range - start address is not aligned - 0xfee48618
ERROR: v7_dcache_inval_range - stop address is not aligned - 0xfee48818
CC: Aneesh V <aneesh@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
If malloc() fails, we don't want to continue in ahci_init() and
ahci_init_one(). Also print a more informative error message on
malloc() failures.
CC: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Added chip type detection and twl6032
support in the battery control
and charge functions.
Based on Balaji T K <balajitk@ti.com> patches for TI u-boot.
Signed-off-by: Oleg Kosheliev <oleg.kosheliev@ti.com>
The data struct is used to support different
PMIC chip types. It contains the chip type and
the data (e.g. registers addresses, adc multiplier)
which is different for twl6030 and twl6032.
Replaced some hardcoded values with the
structure vars.
Based on Balaji T K <balajitk@ti.com> patches for TI u-boot.
Signed-off-by: Oleg Kosheliev <oleg.kosheliev@ti.com>
This patch add new defines for usb phy for Exynos4x12.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
There is no need to pass p->bus differently when the PMIC is connected via SPI
or via I2C.
Handle the both cases in the same way.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add support for Freescale T2080/T2081 SoC.
T2080 includes the following functions and features:
- Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 mEMACs for network interfaces (four 1Gbps MACs and four 10Gbps/1Gbps MACs)
- High-speed peripheral interfaces
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
- Two serial ATA (SATA 2.0) controllers
- Two high-speed USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Differences between T2080 and T2081:
Feature T2080 T2081
1G Ethernet numbers: 8 6
10G Ethernet numbers: 4 2
SerDes lanes: 16 8
Serial RapidIO,RMan: 2 no
SATA Controller: 2 no
Aurora: yes no
SoC Package: 896-pins 780-pins
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
There are more than two 10GEC in single FMAN in some SoCs(e.g. T2080).
This patch adds support for 10GEC3 and 10GEC4.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Freescale IFC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the driver to driver/misc
and fix the header file includes.
Signed-off-by: York Sun <yorksun@freescale.com>
The DRAM base has been zero for Power SoCs. It could be non-zero
for ARM SoCs. Use a macro instead of hard-coding to zero.
Signed-off-by: York Sun <yorksun@freescale.com>
Some DDR registers' fields have expanded to accommodate larger values.
These changes are backward compatible. Some fields are removed for newer
DDR controllers. Writing to those fields are safely ignored.
TIMING_CFG_2 register is fixed. Additive latency is added to RD_TO_PRE
automatically. It was a misunderstanding in commit c360ceac.
Signed-off-by: York Sun <yorksun@freescale.com>
Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.
Signed-off-by: York Sun <yorksun@freescale.com>
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
Some GPIO connected LEDs have inverted polarity.
Introduce new config option: CONFIG_GPIO_LED_INVERTED_TABLE for the
specifying the inverted GPIO LEDs list and add support for this in the
gpio_led driver.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Ilya Ledvich <ilya@compulab.co.il>
Add a check for the gpio_request() function return value and do not try
to configure the GPIO if the gpio_request() call fails.
Also, print an error message indicating the gpio_request() has failed.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Ilya Ledvich <ilya@compulab.co.il>
This chip is compatible with the existing driver, except that it uses
BAR2 instead of BAR1 for the I/O memory region. Using this patch I can
use the PCIe ethernet interface on the CompuLab Trimslice to boot from
the network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276477
Instead of directly calling the low-level invalidate_dcache_range() and
flush_cache() functions, provide thin wrappers that take into account
alignment requirements.
While at it, fix a case where the cache was flushed but should have been
invalidated, two cases where the buffer data was flushed instead of the
descriptor and a missing cache invalidation before reading the packet
data that the NIC just wrote to memory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276474
Added d-cache support for zynq_gem.c,
Observed a difference of +0.8 MiB/s when downloading
a file of size of 3007944Bytes.
With d-cache OFF:
----------------
Filename 'uImage'.
Load address: 0x800
Loading: #################################################################
#################################################################
#################################################################
##########
1.3 MiB/s
done
Bytes transferred = 3007944 (2de5c8 hex)
With d-cache ON:
---------------
Filename 'uImage'.
Load address: 0x800
Loading: #################################################################
#################################################################
#################################################################
##########
2.1 MiB/s
done
Bytes transferred = 3007944 (2de5c8 hex)
Changes on zynq_gem for d-cache support:
- Tx and Rx buffers are cache-aligned
- Updated logic for invalidating Rx buffers and flushing Tx buffers.
- Tx and Rx BD's are allocated from non-cacheable region.
(When BDs are cached, we don't see a consistent link)
- Use TX BD status intead of txsr status checks.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When an unprogrammed EEPROM is attached to a dm9000, the dm9000 will
come up with a invalid MAC address of ff:ff:ff:ff:ff:ff. Add code that
gets enabled if CONFIG_RANDOM_MACADDR is enabled that generates a random
(and valid) locally administered MAC address that allows the system to
network boot until a real MAC address can be configured.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
The e1000 driver expects to always have some kind of non-volatile memory
attached directly to the ethernet controller chip. This means that I would
have to add an additional separate flash chip to my custom board just to
store essentially the MAC address. Since I don't want to do that, this patch
introduces a new config option CONFIG_E1000_NO_NVM. If defined it disables
all accesses to the NVM. I have tested the patch with a 82574 controller.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
The masks were ignoring the last 4 bits which didn't allow detection differences
between the ar8031 and ar8035.
Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Patch: 288018
The both AR8031 and AR8035 belong to Atheros 803x serial PHY.
So the phy id mask of AR8031 is the same to the phy id mask
of AR8035. The right mask value is 0x4fffff.
This patch has been tested on the P1010 and P1023.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Patch: 287748
Fix the 32-bit memory access that is not "endianess safe",
i.e. not giving the desired byte layout for LE cpus:
tempval = *((uint *) (tmpbuf + 4)), where 'char tmpbuf[]'.
Free the stack from rendundant local vars:
tmpbuf[] and i.
Use a portable type (u32) for the 32bit tsec register value
holder: tempval.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Use cross arch portable u32 instead of uint for the
tsec registers. Remove the typedefs for the register
struct definitions in the process. Fix long lines.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Currently, the buffer descriptor (BD) fields cannot be
correctly accessed by a little endian processor. This
patch fixes the issue by making the access of BDs to be
portable among different cpu architectures.
Use portable data types for the Rx/Tx buffer descriptor
fields. Use portable I/O accessors to insure that the
big endian BDs are correctly accessed by little endian
cpus too, and to insure proper sync with the H/W.
Removed the redundant RTXBD "volatile" type, as proper
synchronization around BD data accesses is provided by
the I/O accessors now.
The "sparse" tool was also used to verify the correctness
of these changes.
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Fix bufPtr and the rxIdx/ txIdx occurrences to
solve the related checkpatch warnings for the
coming patches.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Remove tsec_t typedef. Define macros as getters of
tsec and mdio register memory regions, for consistent
initialization of various 'regs' fields and also to
manage overly long initialization lines.
Use the __iomem address space marker to address sparse
warnings in tsec.c where IO accessors are used, like:
tsec.c:394:19: warning: incorrect type in argument 1 (different
address spaces)
tsec.c:394:19: expected unsigned int volatile [noderef]
<asn:2>*addr
tsec.c:394:19: got unsigned int *<noident>
[...]
Add the __iomem address space marker for the tsec pointers
to struct tsec_mii_mng memory mapped register regions.
This solves the sparse warnings for mixig normal pointers
with __iomem pointers for tsec.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Access to privlist[1] (hardcoded referece to the 2nd tsec's
priv area) is neither correct nor does it make sense in the
current context. Each tsec dev has access to its own priv
instance only, and hence to its own set of group address
registers (GADDR) to filter multicast addresses.
This fix leads to removal of the unused (faulty) privlist[]
and related global static vars. Note that mcast() can be
called only after eth_device allocation and init, and hence
after priv area allocation, so dev->priv is correctly
initialized upon mcast() call.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Patch: 278990
There are several implementation issues for tsec_mcast_addr()
addressed by this patch:
* unmanaged, not portable r/w access to registers; fixed with
setbits_be32()/ clrbits_be32()
* use of volatile pointers
* unnecessary forced cast to u8 for the ether_crc() result
* removed redundant parens
* corrected some comment slips
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Patch: 279000
This fixes the following compiler warnings when activating
CONFIG_MCAST_TFTP:
tsec.c: In function 'tsec_mcast_addr':
tsec.c:130:2: warning: passing argument 2 of 'ether_crc' makes pointer
from integer without a cast [enabled by default]
In file included from /work/u-boot-net/include/common.h:874:0,
from tsec.c:15:
/work/u-boot-net/include/net.h:189:5: note: expected 'const unsigned
char *' but argument is of type 'u8'
tsec.c: In function 'tsec_initialize':
tsec.c:646:13: warning: assignment from incompatible pointer type
[enabled by default]
eth.c: In function 'eth_mcast_join':
eth.c:358:2: warning: passing argument 2 of 'eth_current->mcast' makes
integer from pointer without a cast [enabled by default]
eth.c:358:2: note: expected 'u32' but argument is of type 'u8 *'
In the eth_mcast_join() implementation, eth_current->mcast()
takes a u8 pointer to the multicast mac address and not a ip
address value as implied by its prototype.
Fix parameter type mismatch for tsec_macst_addr() (tsec.c):
ether_crc() takes a u8 pointer not a u8 value.
mcast() is given a u8 pointer to the multicats mac address.
Update parameter type for the rest of mcast() instances.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Patch: 278989
It's important that buffer descriptors are aligned in accordance to GMAC
data bus width (32/64/128-bit). It's safe to align to 128-bit (16-bytes)
for every bus width type.
If buffer descriptor is improperly aligned GMAC discards lower bits of
provided address and as a result reads from improper location that
doesn't match expected fields.
Commit ef76025a99 "net: Multiple
updates/enhancements to designware.c" introduced another structure
member "link_printed" right before buffer descriptors while "padding"
member was left untouched. This together with alignment of structure
itself to 16-byte boundary forces buffer descriptoprs always to be
4-byte aligned that causes driver complete disfunction if GMAC bus width
is 64 or 128-bit.
Proposed change makes sure all buffer descriptors are 16-byte (128-bit)
aligned.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Patch: 277902
"bus mode" register contains lots of fields and some of them don't
expect to be written with 0 (zero). So since we're only interested in
resetting MAC (which is done with setting the least significant bit of
this register with "0") I believe it's better to modify only 1 bit of
the register.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Vipin Kumar <vipin.kumar@st.com>
Patch: 277864
R8A7791 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7791.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Joe Hershberger <joe.hershberger@gmail.com>
AR8035 driver will be never applied because of wrong mask for
AR8031 driver. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reported-by: Pavel Nakonechny <pavel.nakonechny@skitlab.ru>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Patch: 276944
This chip is compatible with other RTL8168 chips and can be found on the
NVIDIA Cardhu and Beaver boards.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276475
currticks() is defined as get_timer(0), which returns an unsigned long,
so use %lu instead of %d to print the result.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276473
The 'get_phy_driver' code in 'drivers/net/phy/phy.c' uses the following
method to determine which driver is to be loaded for a particular PHY
module:
list_for_each(entry, &phy_drivers) {
drv = list_entry(entry, struct phy_driver, list);
if ((drv->uid & drv->mask) == (phy_id & drv->mask))
return drv;
}
This means that a drv->mask of 0xfffff0 will return incorrect phy driver
for the logic above, even if the drv->uid is anything other than
something ending with a 0x0.
For e.g. if the RTL8211E drv->uid is 0x1cc915 and drv->mask is 0xffffff
and the RTL8211B drv->uid is 0x1cc910 and drv->mask is 0xffffff0, then
the phy driver selected will always be RTL8211B even though the
underlying phy connected on the board is a 8211E module.
This patch fixes this issue.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
This patch adds support for VSC8514 PHY module which can be
found on Freescale's T1040RDB boards.
Signed-off-by: Arpit Goel <B44344@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
R8A7790 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7790.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The sh-eth of rmobile needs to use invalidate_cache* function.
This patch adds invalidate_cache* function.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Patch: 268948
sh-eth can change the alignment size of a packet descriptor according to BUS
size. This patch adds this function.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The cache API of SH was changed from dcache_wback_range to flush_dcache_range.
sh-eth uses dcache_wback_range. This patch changes to flush_dcache_range.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Avoid a recently introduced unused variable warning for boards that
use mvgbe but not phylib.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
Patch: 266334
As AR8031 and AR8033 have same PHY ID 0x4dd074, they use the
common driver. Currently AR8031_driver didn't work for AR8033,
hence updated it to have it work on AR8031/AR8033.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed
CONFIG_xx used for selecting NAND ecc-schemes.
This patch aims at solving following issues.
1) Currently ecc-scheme is tied to SoC platform, which prevents user to select
other ecc-schemes also supported in hardware. like;
- most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite
the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with
software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW).
- most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware
supports BCH16 ecc-scheme also.
2) Different platforms use different CONFIG_xx to select ecc-schemes, which
adds confusion for user while migrating platforms.
- *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only
8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW)
whereas ELM hardware engine supports other ecc-schemes also like; BCH4,
and BCH16 (in future).
- *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error
correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW).
- *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library
Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency
on SoC platform and NAND driver. And user can select ecc-scheme independently
foreach board.
However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still
depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand)
Signed-off-by: Pekon Gupta <pekon@ti.com>
BCH8_ECC scheme implemented in omap_gpmc.c driver has following favours
+-----------------------------------+-----------------+-----------------+
|ECC Scheme | ECC Calculation | Error Detection |
+-----------------------------------+-----------------+-----------------+
|OMAP_ECC_BCH8_CODE_HW |GPMC |ELM H/W engine |
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |GPMC |S/W BCH library |
+-----------------------------------+-----------------+-----------------+
Current implementation limits the BCH8_CODE_HW only for AM33xx device family.
(using CONFIG_AM33XX). However, other SoC families (like TI81xx) also have
ELM hardware module, and can support ECC error detection using ELM.
This patch
- removes CONFIG_AM33xx
Thus this driver can be reused by all devices having ELM h/w engine.
- adds omap_select_ecc_scheme()
A common function to handle ecc-scheme related configurations. This
can be used both during device-probe and via user-space u-boot commads
to change ecc-scheme. During device probe ecc-scheme is selected based
on CONFIG_NAND_OMAP_ELM or CONFIG_NAND_OMAP_BCH8
- enables CONFIG_BCH
S/W library (lib/bch.c) required by OMAP_ECC_BCHx_CODE_HW_DETECTION_SW
is enabled by CONFIG_BCH.
- enables CONFIG_SYS_NAND_ONFI_DETECTION
for auto-detection of ONFI compliant NAND devices
- updates following README doc
doc/README.nand
board/ti/am335x/README
doc/README.omap3
Signed-off-by: Pekon Gupta <pekon@ti.com>
[scottwood@freescale.com: fixed unused variable warning]
Signed-off-by: Scott Wood <scottwood@freescale.com>
ELM hardware engine which is used for ECC error detection, is present on all
latest OMAP SoC (like OMAP4xxx, OMAP5xxx, DRA7xxx, AM33xx, AM43xx). Thus ELM
driver should be moved to common drivers/mtd/nand/ folder so that all SoC
having on-chip ELM hardware engine can re-use it.
This patch has following changes:
- mv arch/arm/include/asm/arch-am33xx/elm.h arch/arm/include/asm/omap_elm.h
- mv arch/arm/cpu/armv7/am33xx/elm.c drivers/mtd/nand/omap_elm.c
- update Makefiles
- update #include <asm/elm.h>
- add CONFIG_NAND_OMAP_ELM to compile driver/mtd/nand/omap_elm.c
and include in all board configs using AM33xx SoC platform.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Current IFC driver supports till 4K page size NAND flash.
Add support of 8K NAND flash
- Program Spare region size in csor_ext
- Add nand_ecclayout for 4 bit & 8 bit ecc
- Defines constants
- Add support of 8K NAND boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Liu Po <po.liu@freescale.com>
nand_ecclayout is present in mtd.h at Linux.
Move this structure to mtd.h to comply with Linux.
Also, increase the ecc placement locations to 640 to suport device having
writesize/oobsize of 8KB/640B. This means that the maximum oobsize has gone
up to 640 bytes and consequently the maximum ecc placement locations have
also gone up to 640.
Changes from Prabhabkar's version (squashed into one patch to preserve
bisectability):
- Added _LARGE to MTD_MAX_*_ENTRIES
This makes the names match current Linux source, and resolves
a conflict between
http://patchwork.ozlabs.org/patch/280488/
and
http://patchwork.ozlabs.org/patch/284513/
The former was posted first and is closer to matching Linux, but
unlike Linux it does not add _LARGE to the names. The second adds
_LARGE to one of the names, and depends on it in a subsequent patch
(http://patchwork.ozlabs.org/patch/284512/).
- Made max oobfree/eccpos configurable, and used this on tricorder,
alpr, ASH405, T4160QDS, and T4240QDS (these boards failed to build
for me without doing so, due to a size increase).
On tricorder SPL, this saves 2576 bytes (and makes the SPL build
again) versus the new default of 640 eccpos and 32 oobfree, and
saves 336 bytes versus the old default of 128 eccpos and 8 oobfree.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Vipin Kumar <vipin.kumar@st.com>
[scottwood@freescale.com: changes as described above]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
