This patch allows to switch the CPU frequency to 800MHz on the
ST Microelectronics board (DK1/DK2 and EV1) or dh electronics SOM
using the STM32MP15x SOC and when it is supported by the HW
(for STM32MP15xD and STM32MP15xF).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function stmpic_init to early initialize the PMIC STPMIC1
- keep vdd on during the reset cycle (to avoid issue when backup battery
is absent)
- Check if debug is enabled to program PMIC according to the bit
This patch allows to remove the compilation of spl.c file from stm32mp1
board in dh_stm32mp1.
CONFIG_SPL_BOARD_INIT is removed as the new function is called earlier
in SPL, in the function board_early_init_f.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a weak functions to save the vddcore voltage value provided
in the OPP node when the clock tree is initialized.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This commit adds cpufreq support on stm32mp15x SOC. STM32 cpufreq uses
operating points V2 bindings (no legacy). Nvmem cells have to be used to
know the chip version and then which OPPs are available. Note that STM32
cpufreq driver is mainly based on "cpufreq-dt" driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add the bsec driver in SPL, as it is needed by SOC part number detection
to found the supported OPP.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- Resync Kconfiglib with the v14.1.0 release.
- Re-sync our <linux/compiler*h> files with v5.7-rc5 from upstream.
- Fully resync checkpatch.pl with v5.7 release.
To safely to all of the above, we have a few bugfixes about functions
that need a 'static inline' but weren't. We also stop setting
CROSS_COMPILE in arch/*/config.mk. Finally, with the above changes
boards can now opt-in to optimizing inlining and we do this for the
socfpga stratix10 platform for space savings.
currently gpio hog function is not tested with "ut dm gpio"
so add some basic tests for gpio hog functionality.
For this enable GPIO_HOG in sandbox_defconfig, add
in DTS some gpio hog entries, and add testcase in
"ut dm gpio" command.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace printf() and debug() by log_err() and log_debug().
"No reserved memory region found in source FDT\n" is not an error but a
debug information.
%s/can not/cannot/ - use the more common spelling.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Add L2 cache node to enable all cache ways from U-Boot proper.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
fdtdec_get_addr_size_no_parent is not an optimized version if parent
node is already available with the caller.
Use fdtdec_get_addr_size_auto_parent to read the "reg" property
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Not all errors are fatal. If a reserved memory node already exists in the
destination device tree, we can continue to boot without failing.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Starting from OpenSBI v0.7, the SBI firmware inserts/fixes up the
reserved memory node for PMP protected memory regions. All RISC-V
boards need to copy the reserved memory node from the device tree
provided by the firmware to the device tree used by U-Boot.
Turn on CONFIG_OF_BOARD_FIXUP by default for OF_SEPARATE.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The FDT blob might not have sufficient space to hold a copy of
reserved memory node. Expand it before the copy.
Reported-by: Rick Chen <rick@andestech.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The copy of reserved memory node from source dtb to destination dtb
can be avoided if they point to the same place. This is useful when
OF_PRIOR_STAGE is used.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Unless we mark the function as 'static inline' it may end up being
non-inlined by the compiled and result in duplicate functions.
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Vasut <marex@denx.de>
In order to update our <linux/compiler.h> to a newer version that no
longer provides ACCESS_ONCE() but only READ_ONCE()/WRITE_ONCE() we need
to convert arch/x86/include/asm/atomic.h to the other macros.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to update our <linux/compiler.h> to a newer version that no
longer provides ACCESS_ONCE() but only READ_ONCE()/WRITE_ONCE() we need
to convert arch/arm/mach-tegra/ivc.c to the other macros.
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to support the compiler providing information used within
Kconfig itself we cannot have the compiler be determined by
arch/*/config.mk as we will not be able to evaluate that yet. Given
that most documentation tells people to specify CROSS_COMPILE, remove
these references.
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Rick Chen <rick@andestech.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Add cpu aliases to U-Boot specific dtsi for hifive-unleashed.
Without aliases we see that the CPU device sequence numbers are set
randomly and the cpu list/detail command will show it as follows:
=> cpu list
1: cpu@1 rv64imafdc
2: cpu@2 rv64imafdc
3: cpu@3 rv64imafdc
0: cpu@4 rv64imafdc
Seems like CPU probing with dm-model also relies on aliases as observed
in case spi. The fu540-c000-u-boot.dtsi has cpu nodes and so adding
corresponding aliases we can ensure that cpu devices are assigned
proper sequence as follows:
=> cpu list
1: cpu@1 rv64imafdc
2: cpu@2 rv64imafdc
3: cpu@3 rv64imafdc
4: cpu@4 rv64imafdc
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
The Sipeed Maix series is a collection of boards built around the RISC-V
Kendryte K210 processor. This processor contains several peripherals to
accelerate neural network processing and other "ai" tasks. This includes a
"KPU" neural network processor, an audio processor supporting beamforming
reception, and a digital video port supporting capture and output at VGA
resolution. Other peripherals include 8M of sram (accessible with and
without caching); remappable pins, including 40 GPIOs; AES, FFT, and SHA256
accelerators; a DMA controller; and I2C, I2S, and SPI controllers. Maix
peripherals vary, but include spi flash; on-board usb-serial bridges; ports
for cameras, displays, and sd cards; and ESP32 chips. Currently, only the
Sipeed Maix Bit V2.0 (bitm) is supported, but the boards are fairly
similar.
Documentation for Maix boards is located at
<http://dl.sipeed.com/MAIX/HDK/>. Documentation for the Kendryte K210 is
located at <https://kendryte.com/downloads/>. However, hardware details are
rather lacking, so most technical reference has been taken from the
standalone sdk located at
<https://github.com/kendryte/kendryte-standalone-sdk>.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Where possible, I have tried to find compatible drivers based on the layout
of registers. However, many devices remain untested. All untested devices
have been left disabled, but some tentative properties (such as compatible
strings, and clocks, interrupts, and resets properties) have been added.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Currently, one cannot use a reset driver on RISC-V. Follow the MIPS
example, and disable the default reset handler when the sysreset driver is
enabled.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some older processors (notably the Kendryte K210) use an older version of
the RISC-V privileged specification. The primary changes between the old
and new are in virtual memory, and in the merging of three separate counter
enable CSRs. Using the new CSR on an old processor causes an illegal
instruction exception. This patch adds an option to use the old CSRs
instead of the new one.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The previous IPI code initialized the device whenever the first call was
made to a riscv_*_ipi function. This made it difficult to determine when
the IPI device was initialized. This patch introduces a new function
riscv_init_ipi. It is called once during arch_cpu_init_dm. In SPL, it is
called in spl_invoke_opensbi. Before this point, no riscv_*_ipi functions
should be called.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
On some platforms (k210), the previous stage bootloader may have not
cleared pending IPIs before transferring control to U-Boot. This can cause
race conditions, as multiple harts all attempt to initialize the IPI
controller at once. This patch clears IPIs before enabling them, ensuring
that only one hart modifies shared memory at once.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This header depended on bd_t and ulong, but did not include the appropriate
headers.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds a generic reset driver. It is designed to be useful when
one has a register in a regmap which contains bits that reset other
devices. I thought this seemed like a very generic use, so here is a
generic driver. The overall structure has been modeled on the syscon-reboot
driver.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This type of bus is used in Linux to designate buses which have power
domains and/or clocks which need to be enabled before their child devices
can be used. Because power domains are automatically enabled before probing
in U-Boot, we just need to enable any clocks present.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Minor updates to some platforms I am the listed maintainer of.
Notably this removes the ti814x_evm which stopped building with the PXA
MMC migration series (oops) but hasn't been functional in some time.
The TI814x (DM814x) platform is rather old and in need of a lot of
migration work. As much of that work is well past the deadline, remove
this platform.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAl76U4wACgkQKPlOlyTy
XBhKeg/6Au6lPC5QLnjEO5gpuhI/eF555jRoABXUNoM8FUjkcqA207Sgd3iTH9lS
imOGHkzwipYno5pY1UoiXr7RKJgAkJfKYWRrZ46qgITrEkgQ8Xyp46xIqhoHvpuH
Qs1YeDllHeRViBt2ZP6UJsYfUIA9xnU/o9tLh4lx2SiCPWbNDns7cB0Ajazh47Cx
8UT2ZwbATaaFfN9m4Lg65O6Fe1G/cHAw5H/xsDajpVOpskHk0RZxRxzob6XLQete
sVkZdjYmH7zG+7THLkPriu2y/qlc5t2re3OeAr/5YwYJODnj3aN7iI20Sl9xMwDP
eDcSt19HMs+Ng60+yqwHxoU+AQ2BjswYHssb2vdY8OQhlRpoFke6nT+oQtCQCYhZ
At/b2O8kh9IM9alsc8xltMABLgrOhREfxC6VQg7bsCH01+qcojGX8dhVQrYsWkKQ
GrCs6SAl8zR78j8s3OGSsvTczMkTrBTglYWIYrlvA5fFhVg5Yz38S+ioTqPc4QDc
ZJ9bDDO00CY4hJC8sx4TQcsn0OmSJeN394dy6CUoxL6fEXBdRmNRLBUnmuTmPmYT
suLB9qaG+Q6cEttXjfNN1VotSG+61COUZ0uoed47cGUo8AxLMTEe62twUc0aDPNS
NMUoMwHqVbivaGUBfG16mu8bnVfaCqFyR/LLGa6J3yQSQ8qeu30=
=dnTK
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-06-29' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next
- net: pcnet: cleanup and add DM support
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
This patch moves the CONFIG_DM_SPI_FLASH and CONFIG_SPI_FLASH_DATAFLASH
to be defined in Kconfig, not in board specific header file
(include/configs/<board>.h).
Before this change the CONFIG_DM_SPI_FLASH was not set in .config (so it
was not possible to use CONFIG_IS_ENABLED(DM_SPI_FLASH) in SPI DM/DTS
converted drivers), but it was set in u-boot.cfg file.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
This patch fixes issue with defining the DM_SPI_FLASH in the
configs/include/<board.h> instead of enabling this option in Kconfig.
The problem is that CONFIG_IS_ENABLED(DM_SPI_FLASH) shows false as there
is no DM_SPI_FLASH=y in .config (but the define is set in u-boot.cfg).
As a result conversion of DM_SPI_FLASH to using CONFIG_IS_ENABLED() is not
working properly.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
In the future if we have separate symbols for DM_SPI_FLASH and
SPL_DM_SPI_FLASH we will not always have function declarations available
for some DM calls. This in turn leads to build warnings but not
failures as the code isn't used and is discarded at link time.
Restructure things to not build code we won't use for TPL anyways.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the setting for noc remap out of SPL code. Changing
noc remap inside SPL results in breaking back to BROM
boot.
Fixes commit c14fe2a8e1 ("rockchip: rk3188: Move SoC
one time setting into arch_cpu_init()").
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
While in most cases CSF_SIZE is handled via Kconfig we have some i.MX8M
platforms that set the size based on the now-renamed CONFIG_SECURE_BOOT
symbol. Update things so that CSF_SIZE itself depends on IMX_HAB being
enabled and provide the default value for i.MX8M family of parts.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ye Li <ye.li@nxp.com>
There are a few remaining places where we say CONFIG_SECURE_BOOT rather
than CONFIG_IMX HAB. Update these instances.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Fix EMAC register address calculation, address need to multiply
with sizeof(u32) or 4.
This fixes write to invalid address.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Set this value in global_data so that it is reported correctly on x86
boards.
In fact, U-Boot allocates space for the frame buffer even though it is not
used. Then the FSP picks the address itself (e.g. 0xb0000000). So the
value set by U-Boot (high in memory with everything else that is
relocated), is not actually the correct value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't have an easy way to share these three lines of code with two
architectures. We also want to make it clear that this code is actually
arch-specific.
So just duplicate it in each arch-specific file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We don't really want to have m68k-specific code in a generic file. Create
a new arch-specific function to hold it, and move it into that.
Make the function weak so that any arch can implement it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Tested-by: Angelo Dureghello <angelo.dureghello@timesys.com>
We don't really want to have PPC-specific code in a generic file. Create
a new arch-specific function to hold it, and move it into that.
Make the function weak so that any arch can implement it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We don't really want to have ARM-specific code in a generic file. Create
a new arch-specific function to hold it, and move it into that.
Make the function weak so that any arch can implement it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
