fdt_addr_t is a physical address. It can be either 64-bit or 32-bit,
depending on the architecture. It should be phys_addr_t instead of
u64 or u32. Similarly, fdt_size_t is changed to phys_size_t.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Simon Glass <sjg@chromium.org>
fdt_addr_t is changed to phys_addr_t. The format in debug should be updated
to %pa to match the type.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Simon Glass <sjg@chromium.org>
Spring is the first ARM-based HP Chromebook 11. It is similar to snow
and it uses the same Samsung Exynos5250 chip. But has some unusual
features. Mainline support for it has lagged snow (both in kernel and
U-Boot). Now that the exynos5 code is common we can support spring just
by adding a device tree and a few lines of configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove the old drivers (both the normal one and the cros_ec one) now that
we have new drivers that use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that most exynos5250 boards can use the generic exynos5 code, switch
over to it and remove the old code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that exynos5420 boards can use the generic exynos5 code, switch over to
it and remove the old code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Many options are duplicated on the exynos5 boards. Move these to the common
files. Also some options are not used so can be removed.
Tidy this up to make the files easier to maintain.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Some boards use device tree for almost all board-specific configuration.
They therefore do not need their own separate board code, but can all use
the same version. Add a common version of the board code. It uses the
PMIC, regulator and video bridge uclasses. This will support smdk5250,
smdk5420, snow, spring, pit and pi.
Signed-off-by: Simon Glass <sjg@chromium.org>
While the AP can access the main PMIC on snow, it must coordinate with the
EC which also wants access. Drop the old definition, which can in principle
generate collision errors. We will use the new arbitration driver instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
The new driver supports driver model and configuration via device tree. Add
a node for pit, which needs this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a description of the snow memory layout to assist flashing tools which
want to be able to deal with any exynos image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since a gpio_desc is allowed to be invalid we should return an error
indicating that the operation cannot be completed. This can happen if the
GPIO is optional - e.g. some devices may have a reset line and some may
not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Line up the display with the line below, e.g.:
CPU: Exynos5250 @ 1.7 GHz
Model: Google Spring
DRAM: 2 GiB
MMC: EXYNOS DWMMC: 0
Also show the speed as GHz where appropriate.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not print a message from the driver when the display is set up.
This is normal behaviour. Change this message to use debug().
Also remove the double newline on another debug message.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since the timeout is reported through normal channels, and is sometimes
expected (e.g. if the bus is being probed for a non-existent device),
don't display the message in the driver.
In general, drivers should not write to the console as this limits their
usefulness in error conditions.
Signed-off-by: Simon Glass <sjg@chromium.org>
This chip provides an eDP to LVDS bridge which is useful for SoCs that don't
support LVDS displays (or it would waste scarce pins). There is no setup
required by this chip, other than to adjust power-down and reset pins, and
those are managed by the uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
This chip provides an eDP to LVDS bridge which is useful for SoCs that don't
support LVDS displays (or it would waste scarce pins). The setup is included
in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
We haven't quite got pinctrl ready to apply to mainline. We don't want to
GPIO pull-up/down support to the driver model GPIO layer either. So work
around this for now.
We can address this when pinctrl is complete.
Signed-off-by: Simon Glass <sjg@chromium.org>
A video bridge typically converts video from one format to another, e.g.
DisplayPort to LVDS. Add driver model support for these with a simple
interface to control activation and backlight. The uclass supports GPIO
control of power and reset lines.
Signed-off-by: Simon Glass <sjg@chromium.org>
When a regulator command cannot honour the requested voltage, display the
limits to try to be helpful.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Not all regulators can be set up automatically. Adjust the code so that
regulators_enable_boot_on() will return success when some are skipped.
Only genuine errors are reported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Some regulators use the wrong voltage register and thus it is not possible
to control them. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This should write the register, not read it. Fix this bug.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The driver name should not have a space in it. Also the regulator names
should match the case of the device tree. Fix these problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This PMIC is used with SoCs which need a combination of BUCKs and LDOs. The
driver supports changing voltage and enabling/disabling each regulator. It
supports the standard device tree binding and supports driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This PMIC is used with SoCs which need a combination of BUCKs and LDOs. The
driver supports probing and basic register access. It supports the standard
device tree binding and supports driver model. A regulator driver can be
provided also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The TPS65090 has 7 FETs which are modelled as regulators. This allows them
to be controlled by drivers easier, accessed through the 'regulator' command
and used by other drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The existing TPS65090 driver does not support driver model. Add a new one
that does. This can be used as a base for a regulator driver also. It uses
the standard device tree binding.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
As a debugging aid, allow UART3 to be used as a debug UART in SPL. This
is a precursor to proper UART support, which requires a substantial
refactor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a debug UART implementation for this serial driver. It does not set up
pinmux automatically - this must be done before calling debug_uart_init().
Signed-off-by: Simon Glass <sjg@chromium.org>
The debug UART code needs to perform the same init as the normal UART
driver. In preparation for this, move the init code into two functions, one
for the basic init and one for setting the baud rate. This will make adding
debug UART support easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a driver to support the special LDO access used by spring. This is a
custom method in the cros_ec protocol - it does not use an I2C
pass-through.
There are two implementation choices:
1. Write a special LDO driver which can talk across the EC. Duplicate all
the logic from TPS65090 for retrying when the LDO fails to come up.
2. Write a special I2C bus driver which pretends to be a TPS65090 and
transfers reads and writes using the LDO message.
Either is distasteful. The latter method is chosen since it results in less
code duplication and a fairly simple (30-line) implementation of the core
logic.
The crosec 'ldo' subcommand could be removed (since i2c md/mw will work
instead) but is retained as a convenience.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Chrome OS EC supports tunnelling through to an I2C bus on the EC. This
currently uses a copy of the I2C command code and a special 'crosec'
sub-command.
With driver model we can define an I2C bus which tunnels through to the EC,
and use the normal 'i2c' command to access it. This simplifies the code and
removes some duplication.
Add an I2C driver which tunnels through to the EC. Adjust the EC code to
support binding child devices so that it can be set up. Adjust the existing
I2C xfer function to fit driver model better.
For now the old code remains to allow things to still work. It will be
removed in a later patch once the new flow is fully enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
On pit and pi the TPS65090 regulator is connected only to the EC and we
must use a tunnel to get to it. The existing U-Boot support relies on a
special driver. Add a tunnel definition so that the new device-model
TPS65090 driver can be used unmodified.
Signed-off-by: Simon Glass <sjg@chromium.org>
Snow and smdk5250 use a max77686 PMIC. We have a driver for this, so add
the relevant node to the device tree so it can be used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The kernel uses upper case for I2C unit addresses. Follow the same
convention to reduce differences.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The existing driver model implementation uses the old non-driver-model code
to operate, but has become impossibly tangled as a result. The actual
algorithm is quite simple.
Also the normal-speed and high-speed buses are quite different and it
doesn't seem that useful to put them in the same driver.
Finally, there is a bug which breaks communication with the Maxim sound
codec and may cause problems with other device.
Rewrite the driver model code for normal-speed operation so that it is
easier to understand, and fix the bug. Add a TODO to split the drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
This function should not use mixed case, and it is simpler to use
clrbits_le32() when clearing bits. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
While I2C supports multi-master buses this is difficult to get right.
The implementation on the master side in software is quite complex.
Clock-stretching and the arbitrary time that an I2C transaction can take
make it difficult to share the bus fairly in the face of high traffic.
When one or more masters can be reset independently part-way through a
transaction it is hard to know the state of the bus.
This driver provides a scheme based on two 'claim' GPIOs, one driven by the
AP (Application Processor, meaning the main CPU) and one driven by the EC
(Embedded Controller, a small CPU aimed at handling system tasks). With
these they can communicate and reliably share the bus. This scheme has
minimal overhead and involves very little code. It is used on snow to
permit the EC and the AP to share access to the main system PMIC and
battery. The scheme can survive reboots by either side without difficulty.
This scheme has been tested in the field with millions of devices.
Since U-Boot runs on the AP, the terminology used is 'our' claim GPIO,
meaning the AP's, and 'their' claim GPIO, meaning the EC's. This terminology
is used by the device tree bindings in Linux also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new I2C_MUX uclass. Devices in this class can multiplex between
several I2C buses, selecting them one at a time for use by the system.
The multiplexing mechanism is left to the driver to decide - it may be
controlled by GPIOs, for example.
The uclass supports only two methods: select() and deselect().
The current mux state is expected to be stored in the mux itself since
it is the only thing that knows how to make things work. The mux can
record the current state and then avoid switching unless it is necessary.
So select() can be skipped if the mux is already in the correct state.
Also deselect() can be made a nop if required.
Signed-off-by: Simon Glass <sjg@chromium.org>
