There is no need to keep a separate coreboot_fb.dtsi since now we
have a generic coreboot payload dts.
While we are here, this also remove the out-of-date description in
the documentation regarding to coreboot framebuffer driver with
U-Boot loaded as a payload from coreboot. As the testing result with
QEMU 2.5.0 shows, the driver just works like a charm.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently building U-Boot as the coreboot payload requires user
to change the build configuration for a specific board during
menuconfig process. This uses the board's native device tree
to configure the hardware. For example, the device tree provides
PCI address range for the PCI host controller and U-Boot will
re-program all PCI devices' BAR to be within this range. In order
to make sure we don't mess up the hardware, we should guarantee
the range matches what coreboot programs the chipset.
But we really should make the coreboot payload support easier.
Just like EFI payload, we can create a generic coreboot payload
for all x86 boards as well. The payload is configured to include
as many generic drivers as possible. All stuff that touches low
level initialization are not allowed as such is the coreboot's
responsibility. Platform specific drivers (like gpio, spi, etc)
are not included.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Since gcc-8 the --enable-default-pie starts producing code which assembler
can't translate in case of U-Boot. The build fails with
{standard input}: Assembler messages:
{standard input}:21100: Error: junk at end of line, first unrecognized character is `@'
{standard input}:21120: Error: junk at end of line, first unrecognized character is `@'
and so on.
This is usually the case for x86 platform because in many cases it uses host
compiler from the Linux distributions, where PIE is enabled by default.
Previously (gcc-7 and earlier) that was a potential issue due to absence of
constructions like
.long end.5561@gotoff-start.5558@gotoff
which are a cause of above error messages in gcc-8.
Fix all these by disabling PIE on Makefile level.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
After creating CONS_INDEX and migrating a bunch of boards to it,
there are a bunch of defined references to CONFIG_SERIALx which
are not referenced in any C code or #ifdef, so they can now be
removed
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_TWL4030_LED
CONFIG_TWL4030_INPUT
This also removes dead references to:
CONFIG_TWL4030_KEYPAD
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_MISC_INIT_R
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate boards which set bootlimit in the environment to Kconfig.
We exclude gurnard_defconfig which includes a bootlimit=, but doesn't set
CONFIG_BOOTCOUNT_LIMIT, so we'd fail to include a bootlimit setting
if we migrated it.
display5_defconfig and display5_factory_defconfig share a SYS_CONFIG_NAME,
but only display5_defconfig enables CONFIG_BOOTCOUNT_LIMIT, so we fail to
set bootlimit= in display5_factory_defconfig. This is okay because the
display5_factory_defconfig doesn't need to have it set, as it is only
meant to prepare the board in the factory.
Environment changes for all modified configs as seen from buildman:
boards.cfg is up to date. Nothing to do.
Summary of 3 commits for 32 boards (8 threads, 1 job per thread)
01: Merge git://git.denx.de/u-boot-x86
arm: + draco etamin rastaban pxm2 display5 thuban rut
02: Add BOOTCOUNT_BOOTLIMIT to set reboot limit
03: Migrate bootlimit to Kconfig
- display5_factory: bootlimit=3
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Replaced misspelled words "parition"/"paritioning" (missing 't') in two
Kconfig files by correct words "partition"/"partitioning"
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
If CONFIG_NR_DRAM_BANKS is bigger than the default
value (4) define MEMORY_BANKS_MAX as CONFIG_NR_DRAM_BANKS.
Fixes: 2a1f4f1758 ("Revert "fdt_support: Use CONFIG_NR_DRAM_BANKS if defined"")
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
While we have long since migrated to CONFIG_SYS_GENERIC_BOARD being
enabled, we had just a few places left that still referenced or defined
it. Update.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable support for USB PHY on the R-Car Gen2. This allows for both
of the USB host ports to be used on such boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add a PHY driver for the R-Car Gen2 which allows configuring the mux
connected to the EHCI controllers and USBHS controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The code fails to copy the last PHY phandle argument, so it is
missing from the adjusted phandle args and the consumer cannot
use it to determine what the PHY should do.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Use clock framework functions to fetch clock information now that there
is a clock driver for Arria10, instead of custom coded register parsing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add support for fetching the clock frequency both using the legacy
method in case clock framework is disabled as well as via the clock
framework if it is enabled. This allows for migration to the clock
framework on platforms which supports it while not breaking legacy
platforms. That said, the legacy method must be removed eventually.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add clock driver for the Arria10, which allows reading the clock
frequency from all the clock described in the DT. The driver also
allows enabling and disabling the clock. Reconfiguring frequency
is not supported thus far.
Since the DT bindings for the SoCFPGA clock are massively misdesigned
and the handoff DT adds additional incorrectly described entries to
the DT, the driver contains workarounds which attempt to rectify all
of those problems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add the pre-reloc DT markers to clock nodes needed in SPL and early
U-Boot stages. This is required to let the Arria10 clock driver start
early and provide clock information for UART and SDMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The variables removed in this patch are never used, they are only ever
assigned and then waste precious memory. Drop both the assignment and
the variables.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The L4SP and MMC clock precalculation is specific to Gen5, it is not
needed on Arria10/Stratix10. Isolate it to Gen5 until there is a proper
clock driver for Gen5, at which point this will go away completely.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Bind fixed clock driver to the base clock instantiated in the handoff
DT and use DM clock framework to get their clock rate. This replaces
the ad-hoc DT parsing present thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Enable DM ethernet framework on Arria10, so that the designware GMAC
can be probed from DT as it should be.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Remove ad-hoc ethernet syscon registers configuration and reset support.
Reset is now handled by the reset framework and the syscon registers are
set in the dwmac_socfpga.c driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Remove code from the reset manager that is never called.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add wrapper around the designware MAC driver to handle the SoCFPGA
specific configuration bits. On Arria10, this is configuration of
syscon phy_intf.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The UART reset handling is now done via reset framework using the
SoCFPGA reset driver. The UART console assignment is done using the
DM and console framework. Nuke all this comlexity, since it is just
duplicating the same functionality, badly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Enable the DM I2C framework on Arria10, so that the DM capable
Designware I2C driver can handle the reset via DM reset framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Enable the DM reset framework and DM reset driver on Arria10 both
in U-Boot and in SPL. This lets U-Boot parse reset control from DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The A10 SoCDK is missing the I2C bus alias, so DM I2C cannot assign
the I2C bus a bus number. Add the missing alias.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The I2Cx resets are missing from DT, so the reset manager
cannot control them. Add the missing DT reset entries.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add the GMAC0,1 OCP resets, which must also be ungated for those GMACs
to work and add GMAC2 reset and OCP resets which were missing altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The UART0 and UART1 resets are missing from DT, so the reset manager
cannot control them. Add the missing DT reset entries.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The Altera reset manager block must be available very early on, since
it controls ie. UART resets. Flag it as pre-reloc.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The restructuring of the SPL dropped registration of the FPGA in SPL,
readd it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Fixes: c859f2a77d ("arm: socfpga: Restructure the SPL file")
Some of the code for low level system initialization in SPL's
board_init_f() and U-Boot's arch_early_init_r() is the same,
so let's combine it into a single function called from both.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Device trees need to have the serial console device available
before relocation and require a stdout-path in chosen at least
for SPL to have a console.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This patch fix the following warnings for for stm32f429
evaluation and discovery boards:
unnecessary #address-cells/#size-cells without "ranges" or
child "reg" property
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>