Commit 2b3f12c2 added support for configurable SMC Rx buffer length on
8xx systems. Enable this feature on TQM8xx* based boards.
This fixes the problem that pasting text in the middle of a line
(i. e. inserting in edit mode) did not work - only the first two
characters got inserted, the rest was lost.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The Zoom2 power reset button is on the top right side of the
main board. Press and hold for about to 8 seconds to completely
reset the board.
Some of the beta boards have a hardware problem that prevents
using this feature. If is difficult to further characterize the
boards that fail. So disable resetting for all beta boards.
The Zoom1 reset button is the red circle on the top right,
front of the board. Press and hold the button for 8 seconds to
completely reset the board.
After analyzing beagle, it was determined that other boards
that use the twl4030 for power managment can also make use
this function.
The resetting is done by the power management part of the twl4030.
Since there is no existing drivers/power, add one.
The compilation of power/twl4030.h is controlled by the config
variable CONFIG_TWL4030_POWER
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
The TWL4030 supplies many peripherals for OMAP3 boards. These include
power management, usb and, keyboard.
The product description is found here:
http://focus.ti.com/docs/prod/folders/print/tps65950.html
Product reference document, tps65950.pdf, is found here:
http://www.ti.com/lit/gpn/tps65950
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
This problem is seen on Zoom1 and Zoom2 in the startup and
when i2c probe is used
Before :
In: serial
Out: serial
Err: serial
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_pin: I2C_STAT=1000
I2C read: I/O error
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
Die ID #327c00020000000004013ddd05026013
Hit any key to stop autoboot: 0
OMAP3 Zoom1# i2c probe
Valid chip addresses:timed out in wait_for_bb: I2C_STAT=1000
02 03 04 05 06 07 08 09 0A 0B 0C 0D <snip>
After :
In: serial
Out: serial
Err: serial
Die ID #327c00020000000004013ddd05026013
Hit any key to stop autoboot: 0
OMAP3 Zoom1# i2c probe
Valid chip addresses: 48 49 4A 4B
The addresses are for the twl4030.
The prescalar that converts the function clock to the sampling
clock is hardcoded to 0. The reference manual recommends 7
if the function clock is 96MHz.
Instead of just changing the hardcoded values, the prescalar
is calculated from the value I2C_IP_CLK.
The i2c #defines are in kHz. The speed passed into the
i2c init routine is in Hz. To be consistent, change the
defines to be in Hz.
The timing calculations are based on what is done in the
linux 2.6.30 kernel in drivers/i2c/buses/i2c_omap.c as
apposed to what is done in TRM.
The major variables in the timing caculations are
specified as #defines that can be overriden as required.
The variables and their defaults are
I2C_IP_CLK SYSTEM_CLOCK_96
I2C_INTERNAL_SAMPLING_CLK 19200000
I2C_FASTSPEED_SCLL_TRIM 6
I2C_FASTSPEED_SCLH_TRIM 6
I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM
I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM I2C_FASTSPEED_SCLH_TRIM
I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM
I2C_HIGHSPEED_PHASE_TWO_SCLH I2C_FASTSPEED_SCLH_TRIM
This was runtime verified on Zoom1, Zoom2, Beagle and Overo.
The 400kHz and 3.4M cases were verifed on test Zoom1,
Zoom2, Beagle and Overo configurations.
Testing for omap2 will be done in a second step as Nishanth
and Jean-Christophe commented.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
DDR2 Auto-calibration needs to be disabled on the NAND booting PPC4xx
targets. Otherwise the configured fixed init values for some DDR2
controller registers (e.g. RQDC) are not initialized at all resulting
in a non working SDRAM.
Signed-off-by: Stefan Roese <sr@denx.de>
Board support for the Guntermann & Drunck CompactCenter and
DevCon-Center.
Based on the AMCC Canyonlands board support by Stefan Roese.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the esd VME8349 board equipped with the
MPC8349. It's a VME PMC carrier board equipped with the Tundra
TSI148 VME-bridge.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Up to this point in time, the sbc8349 board was storing the u-boot
image in flash 2x. One for the HRCW value at the beginning of
flash (0xff80_0000), and once close to the end of flash (0xfff8_0000)
for the actual image that got executed.
This moves the TEXT_BASE to be the beginning of flash, which makes
the second copy of the image redundant, and frees up the flash
from the end of the environment storage to the end of the flash
device itself.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Commit 7024aa14 was supposed to fix the #ifdef/#endif pairing in
include/configs/at91cap9adk.h, but did not cate all problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The reordering of include/common.h by commit fcd3c87e49 broke
boards with status LED support, resulting in
error: #error Status LED configuration missing
errors. Undo this reordering to avoid this issue.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 70ebf316 factored out the ROUND() macro into include/common.h,
not realizing that the primary use of this macro on AT91 systems was
in start.S where common.h was not included, and could not be included
because it contains a lot of C code which the assembler doesn't
understand.
This patch wraps such code in common.h in a "#ifndef __ASSEMBLY__"
construct, and then adds an include to cpu/arm926ejs/start.S thus
solving the problem.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch updates the support for EB+MCF-EV123 board and needs
the [PATCH 1/2 V3] new video driver for bus vcxk framebuffers
* remove the board framebuffer driver
* use the common bus_vcxk framebuffer driver
* adds bmp support
* adds splashimage support
* fix serveral cosmetical errors
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
[agust@denx.de: fixed some style issues before applying]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch adds a new video driver
* adds common bus_vcxk framebuffer driver
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
[agust@denx.de: fixed lots of style issues before applying]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
include/lcd.h has different vidinfo for different platforms,
and several extern declaration, but one for the default case was
missing. This makes them a single extern declaration for everyone.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
This patch adds support for the AVR32 LCD controller. This patch is
based off the latest u-boot-video.
A quick summary of what's going on:-
Enable LCDC pixel clock
Enable LCDC port pins
Add framebuffer pointer to global_data struct
Allocate framebuffer
To use the new code, update your board config to include something like
this:-
#define CONFIG_LCD 1
#if defined(CONFIG_LCD)
#define CONFIG_CMD_BMP
#define CONFIG_ATMEL_LCD 1
#define LCD_BPP LCD_COLOR16
#define CONFIG_BMP_16BPP 1
#define CONFIG_FB_ADDR 0x10600000
#define CONFIG_WHITE_ON_BLACK 1
#define CONFIG_VIDEO_BMP_GZIP 1
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE 262144
#define CONFIG_ATMEL_LCD_BGR555 1
#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
#define CONFIG_SPLASH_SCREEN 1
#endif
The standard U-Boot BMP and Splash-screen features should just work.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
[agust@denx.de: fixed some style issues]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This moves some extern declaration from lcd.c to lcd.h, removing
unneeded ifdef around a pair of them. Additionally, since
gunzip_bmp() was declared static in cmd_bmp.c but extern in lcd.c, I
removed the static. The extra "#include <lcd.h>" in cmd_bmp.c is
added to ensure the header is consistent with the source.
This has been compile-tested on both ARM (at91 boards) and PowerPC
(HH405_config, TQM823L_LCD_config, mcc200_config), to test all use
combinations.
Signed-off-by: Alessandro Rubini <rubini@gnudd.it>
[agust@denx.de: removed gunzip_bmp() fixes as commit c01171ea did it]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This reverts commit b201171f2b.
The commit caused problems for example when unpacking kernel images:
Uncompressing Kernel Image ... Error: inflate() returned -2
GUNZIP: uncompress, out-of-mem or overwrite error - must
RESET board to recover
Conflicts:
include/u-boot/zlib.h
lib_generic/zlib.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch removes the "alterpll" command and replaces it with the now
ppc4xx standard "chip_config" command to configure the I2C bootstrap
EEPROM.
Signed-off-by: Stefan Roese <sr@denx.de>
Kilauea has an AT24C02 EEPROM which has an 8 byte page. Without defining
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS to 3 the "eeprom" command doesn't
work correctly.
Additionally the page write delay (CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS)
is set to a more defensive value of 10ms.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds a generic command for programming I2C bootstrap
eeproms on PPC4xx. An implementation for Canyonlands board is
included.
The command name is intentionally chosen not to be PPC4xx specific.
This way other CPU's/SoC's can implement a similar command under
the same name, perhaps with a different syntax.
Usage on Canyonlands:
=> chip_config
Available configurations (I2C address 0x52):
600-nor - NOR CPU: 600 PLB: 200 OPB: 100 EBC: 100
600-nand - NAND CPU: 600 PLB: 200 OPB: 100 EBC: 100
800-nor - NOR CPU: 800 PLB: 200 OPB: 100 EBC: 100
800-nand - NAND CPU: 800 PLB: 200 OPB: 100 EBC: 100
1000-nor - NOR CPU:1000 PLB: 200 OPB: 100 EBC: 100
1000-nand - NAND CPU:1000 PLB: 200 OPB: 100 EBC: 100
1066-nor - NOR CPU:1066 PLB: 266 OPB: 88 EBC: 88 ***
1066-nand - NAND CPU:1066 PLB: 266 OPB: 88 EBC: 88
=> chip_config 600-nor
Using configuration:
600-nor - NOR CPU: 600 PLB: 200 OPB: 100 EBC: 100
done (dump via 'i2c md 52 0.1 10')
Reset the board for the changes to take effect
Other 4xx boards will be migrated to use this command soon
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
The XPedite1000 is an X-ES product thus it can be put in board/xes along
with other X-ES boards. Along with the move, the board was renamed to
XPedite1000 from XPedite1K to fit X-ES's standard naming convention.
Maintainership was also transfered to Peter Tyser.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The XPedite1000 only has 2 available ethernet ports:
ppc_4xx_eth2 (EMAC2) and ppc_4xx_eth3 (EMAC3)
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Previously an I2C EEPROM was used. The EEPROM had size, reliability,
and access issues which are resolved by storing the environment in
flash.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The XPedite1000 can be built with 4 total flashes:
- 512KB AMD socketed
- 16MB Intel soldered
- 2 x 32MB AMD MirrorBit flashes
Add support for the optional 2 32MB CFI-compliant AMD flashes
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
By default, the XPedite1000 comes installed with xMon, a proprietary
bootloader. xMon stores its MAC address in an onboard EEPROM. Rather
than requiring a non-standard location in the EEPROM to be reserved for
MAC addresses, store the MAC addresses in U-Boot's standard environment.
A U-Boot application or OS application can be used to migrate xMon MAC
addresses to U-Boot's environment if necessary.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Using the CFI flash driver will allow write access to the 16MB Intel
StrataFlash present on the XPedite1000. The 512KB socketed (non
CFI-compliant flash) will no longer be writable.
The mapping of the 16MB Strata flash was moved to 0xff000000 and the
512KB AMD socketed flash was moved to 0xfe000000.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds I2C support for mvBC-P and defines flash layout
matching the shipped product.
Signed-off-by: Andr Schwarz <andre.schwarz@matrix-vision.de>
This patch updates zlib to the latest stable version.
Only relevant zlib parts were ported to u-boot tree, as was done for
the previously used version of zlib (0.95). New zlib gives faster
inflate performance and other improvements, see www.zlib.net
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Reviewed-by: Angelo Castello <angelo.castello@st.com>
Edited commit message
Signed-off-by: Wolfgang Denk <wd@denx.de>
All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
- changed CONFIG_DRIVER_SMC911X* to CONFIG_SMC911X*
- cleaned up line lengths
- modified all boards that override weak function in this driver
- added
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Tested-by: Mike Frysinger <vapier@gentoo.org>
On 04 Oct 2008 Pieter posted a dns implementation for U-Boot.
http://www.mail-archive.com/u-boot-users@lists.sourceforge.net/msg10216.html
>
> DNS can be enabled by setting CFG_CMD_DNS. After performing a query,
> the serverip environment var is updated.
>
> Probably there are some cosmetic issues with the patch. Unfortunatly I
> do not have the time to correct these. So if anybody else likes DNS
> support in U-Boot and has the time, feel free to patch it in the main tree.
Here it is again - slightly modified & smaller:
- update to 2009-06 (Pieter's patch was for U-Boot 1.2.0)
- README.dns is added
- syntax is changed (now takes a third option, the env var to store
the result in)
- add a random port() function in net.c
- sort Makefile in ./net/Makefile
- dns just returns unless a env var is given
- run through checkpatch, and clean up style issues
- remove packet from stack
- cleaned up some comments
- failure returns much faster (if server responds, don't wait for
timeout)
- use built in functions (memcpy) rather than byte copy.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Pieter Voorthuijsen <pieter.voorthuijsen@prodrive.nl>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The net code is mostly consistent in using 'Packet' rather than 'Pkt', so
rename the minor detractor to follow suite.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This is Marvell's 88F6281_A0 based reference design board
This patch is tested for-
1. Boot from DRAM/NAND flash/NFS
2. File transfer using tftp and loadb
3. NAND flash read/write/erase
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Use the MPC8572's eLBC to access 1 GB (or greater) onboard NAND flash
via the 'nand' command.
Previously, the XPedite5370's NAND chip selects were properly
configured, but NAND support was not enabled.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Increasing CONFIG_SYS_BOOTM_LEN from 8 MB to 16 MB is necessary to
support uncompressing images larger than 8 MB when using the bootm
command.
Note that recent Linux kernels for the 85xx and 86xx map greater than
16MB of memory on bootup, but we use 16MB to maintain compatibility with
older Linux kernels for now.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Buffered writes are possible on the XPedite5200 and XPedite5370 and greatly
improve NOR flash write speeds
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rename sdram_mode_1 to sdram_mode and sdram_cfg_1 to sdram_cfg to match
the 86xx user's manual and other Freescale architectures
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p2020DS, MPC8536DS, MPC8572DS, MPC8544DS boards are capable of
swizzling the upper address bits of the NOR flash we boot out of which
creates the concept of "virtual" banks. This is useful in that we can
flash a test of image of u-boot and reset to one of the virtual banks
while still maintaining a working image in "bank 0".
The PIXIS FPGA exposes registers on LBC which we can use to determine
which "bank" we are booting out of (as well as setting which bank to
boot out of).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8641HPCN board is capable of swizzling the upper address bit of
the NOR flash we boot out of which creates the concept of "virtual"
banks. This is useful in that we can flash a test of image of u-boot
and reset to one of the virtual banks while still maintaining a
working image in "bank 0".
The PIXIS FPGA exposes registers on LBC which we can use to determine
which "bank" we are booting out of (as well as setting which bank to
boot out of).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A large number of boards (all AT91 based) duplicated the ROUND()
macro in their board specific config files. Add the definition to
include/common.h and clean up the board config files.
Signed-off-by: Wolfgang Denk <wd@denx.de>
We have always mapped at least 16M in the kernel and we have seen cases
with new kernel features that a kernel image needs more than 8M of
memory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_MALLOC_LEN is defined in the board config, and
the keymile-common.h, which collects common options used
by all keymile-boards. This results in a compile error
when compiling the kmeter1 board. So remove this define
in the board config file.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds the possibility to call a board specific
i2c bus reset routine for the fsl_i2c bus driver, and adds
this option for the keymile kmeter1 board.
The deblock sequence for this board is implemented and
tested in the following way:
CR = 0x20 (release SDA and SCL pin)
CR = 0xa0 (start read)
dummy read
dummy read
if 2. dummy read == 0x00
3. dummy read
CR = 0x80 (SDA and SCL now 1 SR = 0x86)
CR = 0x00 (Modul reset SR=0x81)
CR = 0x80 (SDA and SCL = 1, SR = 0x81)
Signed-off-by: Heiko Schocher <hs@denx.de>
- CONFIG_SYS_MAX_I2C_BUS changed to 1
We use only one I2C hardwarecontroller on this boards, so
change the CONFIG_SYS_MAX_I2C_BUS to 1.
- common: dont print errormsg if second IVM Block lacks.
- 82xx, mgcoge: fix double mtdpart entry in environment
- 82xx, mgcoge: activate on second Flash the second bank.
- common: CONFIG_ENV_SIZE 0x4000 for all keymile boards
- common: Change malloc size to 1MByte for all Keymile boards
We need a bigger malloc area for the environment support (128k)
on some Keymile boards (kmeter1) and the upcoming UBI support.
Change it to 1MB for all Keymile boards to be on the save side.
Also define CONFIG_SYS_64BIT_VSPRINTF which is needed for
UBI/UBIFS support.
- Add UBI support to all Keymile boards
- change manner of writing "/localbus/ranges" node
instead of writting the complete "/localbus/ranges" node
before booting Linux, only update the ranges entries
which gets dynamical detected (size of flashes).
This is needed, because keymile adds in the DTS
"/localbus/ranges" node entries, which u-boot must
not overwrite/delete.
- kmeter, mgcoge: define 2 seperate regions needed for the Intel P30 chips
The Intel P30 chip has 2 non-identical chips on
one die, so we need to define 2 seperate regions
that are scanned by physmap_of independantly.
- kmeter1: Add MTD concat support to Keymile boards
- 82xx, mgcoge: add "unlock=yes" to default environment
- added CONFIG_MTD_DEVICE to get in sync with mainline code
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds unaligned.h for ARM (needed to build with LZO
compression). The file is taken from the linux kernel, but includes
u-boot headers instead.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Acked-by: Stefan Roese <sr@denx.de>
Shove a lot of the HOSTCC and related #ifdef checking crap into the new
compiler.h header so that we can keep all other headers nice and clean.
Also introduce custom uswap functions so we don't have to rely on the non
standard implementations that a host may (or may not in the case of OS X)
provide. This allows mkimage to finally build cleanly on an OS X system.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Commit 2419169f removed support for legacy NAND and disk on chip but
missed to update the code for a few boards. This patch fixes the
resulting build issues.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds unaligned.h for ARM (needed to build with LZO
compression). The file is taken from the linux kernel, but includes
u-boot headers instead.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Acked-by: Stefan Roese <sr@denx.de>
This patch adds a SATA harddisk driver for the canyonlands.
This patch is kernel driver's porting.
This patch corresponded to not cmd_scsi but cmd_sata.
This patch divided an unused member with ifndef __U_BOOT__ in the structure.
[environment variable, boot script]
setenv bootargs root=/dev/sda7 rw
setenv bootargs ${bootargs} console=ttyS0,115200
ext2load sata 0:2 0x400000 /canyonlands/uImage
ext2load sata 0:2 0x800000 /canyonlands/canyonlands.dtb
fdt addr 0x800000 0x4000
bootm 0x400000 - 0x800000
If you drive SATA-2 disk on Canyonlands, you must change parts from
PI2PCIE212 to PI2PCIE2212 on U25. We confirmed to boot by using
following disks:
1.Vendor: Fujitsu Type: MHW2040BS
2.Vendor: Fujitsu Type: MHW2060BK
3.Vendor: HAGIWARA SYS-COM:HFD25S-032GT
4.Vendor: WesternDigital Type: WD3200BJKT (CONFIG_LBA48 required)
5.Vendor: WesternDigital Type: WD3200BEVT (CONFIG_LBA48 required)
6.Vendor: Hitachi Type: HTS543232L9A300 (CONFIG_LBA48 required)
7.Vendor: Seagate Type: ST31000333AS (CONFIG_LBA48 required)
8.Vendor: Transcend Type: TS32GSSD25S-M
9.Vendor: MTRON Type: MSD-SATA1525-016
Signed-off-by: Kazuaki Ichinohe <kazuichi at fsi.co.jp>
From: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
This patch adds support for the Tundra TSI148 VME-bridge. It's used on
the upcoming esd VME8349 board.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
While the 1.0 and 1.2 spin of the bf533-stamp boards can handle the higher
SCLK speeds just fine, the 1.1 spin cannot due to the bugs introduced with
the shortened SDRAM traces. So lower the SCLK speed down to a value that
all three can handle.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Part of the mini Blackfin ABI with operating systems is that they can use
0x4f0-0x4f8 to pass log buffers to/from bootloaders. So add support to
U-Boot for reading the log buffer.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.
This patch covers the non-PPC boards that were missed in the previous
patch (commit 170c1972).
Signed-off-by: Wolfgang Denk <wd@denx.de>
This is Marvell's 88F6281_A0 based custom board developed
for wireless access point product
This patch is tested for-
1. Boot from DRAM/SPI flash/NFS
2. File transfer using tftp and loadb
3. SPI flash read/write/erase
4. Booting Linux kernel and RFS from SPI flash
5. Boot from USB supported
Reviewed-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Reference:
http://plugcomputer.org/http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support
This patch is tested for-
1. Boot from DRAM/NAND flash
2. File transfer using tftp
3. NAND flash read/write/erase
4. Linux kernel and RFS Boot from NAND
5. Enabled USB PHY init for kernel need
6. Boot from USB supported
Note: to boot Kirkwood kernel with USB support,
you should add "usb start" in the boot sequence
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Commit 8e55258f created function uec_standard_init() to initialize
all UEC interfaces for 83xx and 85xx but failed to provide a
prototype for it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
So far the console API uses the following naming convention:
======Extract======
typedef struct device_t;
int device_register (device_t * dev);
int devices_init (void);
int device_deregister(char *devname);
struct list_head* device_get_list(void);
device_t* device_get_by_name(char* name);
device_t* device_clone(device_t *dev);
=======
which is too generic and confusing.
Instead of using device_XX and device_t we change this
into stdio_XX and stdio_dev
This will also allow to add later a generic device mechanism in order
to have support for multiple devices and driver instances.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Edited commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
A bug was introduced by commit e94e460c6e
which affected non-MPC83xx/85xx/86xx ppc boards which had CONFIG_DDR_ECC
defined and resulted in errors such as:
Configuring for canyonlands board...
fsl_dma.c:50:2: error: #error "Freescale DMA engine not supported on your
processor"
make[1]: *** No rule to make target `.depend', needed by `libdma.a'. Stop.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
arranged configurations in alphabetical order
CONFIG_CMD_FLASH moved under ifndef CONFIG_SYS_NO_FLASH
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Legacy NAND had been scheduled for removal. Any boards that use this
were already not building in the previous release due to an #error.
The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed. There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This is needed for the MPC512x NAND driver (fsl_nfc_nand.c) which already
defines such a 4k plus 218 bytes ECC layout.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch simply converts the board to the hwconfig infrastructure.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
fdt_fixup_esdhc() will either disable or enable eSDHC nodes, and
also will fixup clock-frequency property.
Plus, since DR USB and eSDHC are mutually exclusive, we should
only configure the eSDHC if asked through hwconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for eSDHC on MPC837XERDB boards. The WP
switch doesn't seem to work on RDB boards though, the WP pin is
always asserted (can see the pin state when it's in GPIO mode).
FSL DR USB and FSL eSDHC are mutually exclusive because of pins
multiplexing, so user should specify 'esdhc' or 'dr_usb' options
in the hwconfig environment variable to choose between the
devices.
p.s.
Now we're very close to a monitor len limit (196 bytes left using
gcc-4.2.0), so also increase the monitor len by one sector (64 KB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This patch implements fdt_fixup_esdhc() function that is used to fixup
the device tree.
The function adds status = "disabled" propery if esdhc pins muxed away,
otherwise it fixups clock-frequency for esdhc nodes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This patch implements simple hwconfig infrastructure: an
interface for software knobs to control a hardware.
This is very simple implementation, i.e. it is implemented
via `hwconfig' environment variable. Later we could write
some "hwconfig <enable|disable|list>" commands, ncurses
interface for Award BIOS-like interface, and frame-buffer
interface for AMI GUI[1] BIOS-like interface with mouse
support[2].
Current implementation details/limitations:
1. Doesn't support options dependencies and mutual exclusion.
We can implement this by integrating apt-get[3] into the
u-boot. But I didn't bother yet.
2. Since we don't implement hwconfig command, i.e. we're working
with the environement directly, there is no way to tell that
toggling a particular option will need a reboot to take
an effect. So, for now it's advised to always reboot the
target after modifying hwconfig variable.
3. We support hwconfig options with arguments. For example,
set hwconfig dr_usb:mode=peripheral,phy_type=ulpi
That means:
- dr_usb - enable Dual-Role USB controller;
- dr_usb:mode=peripheral - USB in Function mode;
- dr_usb:phy_type=ulpi - USB should work with ULPI PHYs;
The purpose of this simple implementation is to define some
internal API and then we can continue improving user experience
by adding more mature interface, like hwconfig command with
bells and whistles. Or not adding, if we feel that current
interface fits its needs.
[1] http://en.wikipedia.org/wiki/American_Megatrends
[2] Regarding ncurses and GUI with mouse support -- I'm just
kidding.
[3] The comment regarding apt-get is also a joke, meaning that
dependency tracking could be non-trivial. For example, for
enabling HW feature X we may need to disable Y, and turn Z
into reduced mode (like RMII-only interface for ethernet,
no MII).
It's quite trivial to implement simple cases though.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Saving the environment leads to overwriting u-boot itself,
bricking boards. Increase u-boot's image size so the environment
base address doesn't end up overlapping u-boot text.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
When enabling NAND support for a board, one must also define
CONFIG_SYS_64BIT_VSPRINTF because this is needed in nand_util.c
for correct output.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Ron Madrid <ron_madrid@sbcglobal.net>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Remove individual CPU specific DSPI driver.
Add required feature for the common DSPI driver in cpu_init and
in platform configuration file.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Update serial boot DRAM's Internal RAM, vector table and DRAM in
start.S, serial flash's read status command over SPI and NOR
flash.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Remove dead code that was obviously a left-over from copy & paste.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Now that we have 3 boards for the MPC512x it turns out that they all
use the very same fixed_sdram() code.
This patch factors out this common code into cpu/mpc512x/fixed_sdram.c
and adds a new header file, include/asm-ppc/mpc512x.h, with some
macros, inline functions and prototype definitions specific to MPC512x
systems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
When enabling NAND support for a board, one must also define
CONFIG_SYS_64BIT_VSPRINTF because this is needed in nand_util.c
for correct output.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
The current defition for CKEN_B register bits is nonsense. Adding 32 to
the shifted value is equal to '| (1 << 5)', and this bit is marked
'reserved' in the PXA docs.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The KSEG1ADDR macro used to be necessary for the RTL8139 Ethernet
driver, but the code that used that macro was removed over a year
ago, so board configuration files no longer need to define it.
The _IO_BASE macro is also automatically defined to 0 if it isn't
already set, so there's no need to define that macro either in the
board configuration files.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The cm-bf561 module can easily hook up to the EXT-BF5xx-USB-ETH2 extender
board, so add a simple example of how to do that in the board config.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The latest blackstamp boards can only run the SPI flash at 15MHz before
they start to crap out, so lower the max speeds accordingly. The new SPI
flash also has different sector requirements, so update the environment
sizes as well.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch use blackfin errno.h implementation which
correspond Linux kernel one.
MIPS implemetation is different that's why I keep it.
I removed ppc_error_no.h from Marvell boards which
was the same too.
I have got ack from ppc40x, blackfin, arm, coldfire and avr custodians.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch fixes 2 problems with FDT EBC mappings on Canyonlands.
First, NAND EBC mapping was missing, making Linux NAND driver
unusable on this board. Second, NOR remapping code assumed that
NOR is always on CS0, however when booting from NAND NOR is on CS3.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently, when booting from NAND using nand_spl, in the beginning the default
environment is used until later in boot process the dynamic environment is read
out. This way environment variables that must be interpreted early, like the
baudrate or "silent", cannot be modified dynamically and remain at their
default values. Fix this problem by reading out main and redundand (if used)
copies of the environment in the nand_spl code.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
nand_util currently uses size_t which is arch dependent and not always a
unsigned long. Now use loff_t, as does the linux mtd layer.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The BF537-STAMP Blackfin board had a driver for working with NAND devices
that are simply memory mapped. Since there is nothing Blackfin specific
about this, generalize the driver a bit so that everyone can leverage it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Update chipselect handling in davinci_nand.c so that it can
handle 2 GByte chips the same way Linux does: as one device,
even though it has two halves with independent chip selects.
For such chips the "nand info" command reports:
Device 0: 2x nand0, sector size 128 KiB
Switch to use the default chipselect function unless the board
really needs its own. The logic for the Sonata board moves out
of the driver into board-specific code. (Which doesn't affect
current build breakage if its NAND support is enabled...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
All DaVinci SOC's use a CLE mask of 0x10 and an ALE mask of 0x8
except the DM646x. This was decided by the design team driving the design.
This patch updates the CLE and ALE values for DM646x.
Updated patches for DM646x will be sent shortly.
This applies to u-boot-nand-flash git
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The ALE mask used by DaVinci SOCs is wrong. The patch changes the mask value
from '0xa' to '0x8'. This is the mask we use for all TI releases.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Remove CONFIG_SYS_DAVINCI_BROKEN_ECC option. It's not just nasty;
it's also unused by any current boards, and doesn't even match the
main U-Boot distributions from TI (which use soft ECC, or 4-bit ECC
on newer chips that support it).
DaVinci GIT kernels since 2.6.24, and mainline Linux since 2.6.30,
match non-BROKEN code paths for 1-bit HW ECC. The BROKEN code paths
do seem to partially match what MontaVista/TI kernels (4.0/2.6.10,
and 5.0/2.6.18) do ... but only for small pages. Large page support
is really broken (and it's unclear just what software it was trying
to match!), and the ECC layout was making three more bytes available
for use by filesystem (or whatever) code.
Since this option itself seems broken, remove it. Add a comment
about the MV/TI compat issue, and the most straightforward way to
address it (should someone really need to solve it).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Minor cleanup for DaVinci NAND code:
- Use I/O addresses from nand_chip; CONFIG_SYS_NAND_BASE won't
be defined when there are multiple chipselect lines in use
(as with common 2 GByte chips).
- Cleanup handling of EMIF control registers
* Only need one pointer pointing to them
* Remove incorrect and unused struct supersetting them
- Use the standard waitfunc; we don't need a custom version
- Partial legacy cleanup:
* Don't initialize every board like it's a DM6446 EVM
* #ifdef a bit more code for BROKEN_ECC
Sanity checked with small page NAND on dm355 and dm6446 EVMs;
and large page on dm355 EVM (packaged as two devices, not one).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller. Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
There is only one public release of the Nomadik chip, so the ifdef
in reset code as well as a define in the config file are not needed
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
To enable CAN init, CONFIG_CAN has to be defined in the board config file
and at91_can_hw_init() has to be called in the board specific code.
CAN is available on AT91SAM9263 and AT91CAP9 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).
This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Defining the next two configs allows to switch the serial port from the
console using the setenv stdin and stdout
1. #define CONFIG_SERIAL_MULTI 1 /* Enable both serial ports */
2. #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initial support for Extreme Engineering Solutions XPedite5170 -
a MPC8640-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
