Commit Graph

67772 Commits

Author SHA1 Message Date
Ye Li
1468a1cc72 usb: ci_udc: Add function to remove usb device
When unregister gadget driver in ci_udc, the usb device is not
removed or stop. This causes next "usb start" fails to work.

Add a new interface "usb_remove_ehci_gadget" in usb-uclass to
remove the usb device for DM driver. Using "usb_lowlevel_stop" for
non-DM driver.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-01 14:47:43 +02:00
Ye Li
213fa47dac usb: gadget: Fix controller index in UMS
The usb mass storage (f_mass_storage.c) uses fixed usb index 0,
this causes problem while CDNS3 USB controller index is 1.
Modify the API of fsg to pass the controller index.

Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-01 14:47:43 +02:00
Hayes Wang
3a41086f6a eth/r8152: support RTL8153B/RTL8154B
This is used to support RTL8153B and RTL8154B.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2020-09-01 14:47:36 +02:00
Hayes Wang
9f6142aa0a eth/r8152: modify rtl_clear_bp function
The original rtl_clear_bp() is used to clear the firmware of both
PLA and USB MCU. The new one could clear the firmware of PLA or
USB independently. It is unnecessary to clear firmware, if there
is no one to be updated.

Besides, clear the firmware by writing the relative registers in
bulk.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2020-09-01 14:47:36 +02:00
Hayes Wang
16b9417b6a eth/r8152: reset PHY after setting it
Some settings of PHY have to work after resetting PHY.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2020-09-01 14:47:36 +02:00
Hayes Wang
d74a76234f eth/r8152: reset bmu after disabling Tx/Rx
Reset bmu after disabling Tx/Rx. This is used to clear the FIFO of
Tx/Rx. The remained data may be transferred after Tx/Rx is re-enabled.
And it results in garbage data.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2020-09-01 14:47:36 +02:00
Masahiro Yamada
23e333a5c0 MAINTAINERS: step down as maintainer of UniPhier SoCs
I am leaving Socionext. Orphan the UniPhier platform until somebody
takes the role.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-08-31 17:11:24 -04:00
Tom Rini
6ade057e37 Merge tag 'ti-v2020.10-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Update to ABI 3.0
- Fix i2c write in eeprom driver
2020-08-31 13:06:26 -04:00
Tom Rini
123f4f84f8 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell
- MVEBU Espressobin fixes and enhancements (fix switch security
  issue, enable MVNETA, enable SD-card, fix COMPHY nodes, default
  env variables, etc)
- MMC Xenon: Set signal voltage and max base clock
- a37xx PCI driver: Depend on DM_GPIO and remove #ifdef's
2020-08-31 09:43:13 -04:00
Pali Rohár
64430efe69 arm: mvebu: Espressobin: Update README.marvell file
Include information about permanent ethernet MAC address and add link how
to build ATF as U-Boot on Espressobin cannot be flashed without ATF.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2020-08-31 14:45:53 +02:00
Pali Rohár
6b61066210 arm: mvebu: Espressobin: Define fdt_addr and kernel_addr env aliases
Boot scripts for existing Espressobin Linux distributions, like OpenWRT,
expect that U-Boot set fdt_addr and kernel_addr envs. So add env aliases
from fdt_addr_r and kernel_addr_r values.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31 14:45:53 +02:00
Pali Rohár
996ecfd3ec arm: mvebu: Espressobin: Change default loadaddr
Current loadaddr is not writable on Espressobin and 'loadb' command cause
rebooting board. Marvell's U-Boot already set default loadaddr to value
0x06000000 [1] and after this change 'loadb' is working fine.

[1] - 0a5b159806

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31 14:45:53 +02:00
Pali Rohár
bb40fe1f6c arm: mvebu: Espressobin: Move env load addresses
According to Marvell's U-Boot description [1] current env load addresses
overlaps with ATF RT services region and TEE. Because the ATF RT service
and TEE region is going to be marked as secure and can't be overwritten,
use different different addresses for envs.

[1] - 0a5b159806

Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2020-08-31 14:45:53 +02:00
Pali Rohár
835d969c1f arm64: a37xx: pci: Depends on DM_GPIO
For proper initialization of aardvark pci driver it is required to
de-assert reset GPIO. So depeneds on DM_GPIO option.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31 14:45:53 +02:00
Pali Rohár
a65e65939e arm: mvebu: Espressobin: Setup MTD partitions when booting kernel
Due to different partition layouts in different U-Boot versions, DTS for
Espressobin in Linux does not contain any definition of MTD partitions.
See commit https://git.kernel.org/stable/c/00954566464a4 for more details.

This patch via ft_board_setup() hook fills current partition layout used by
U-Boot, so booted kernel would see correct MTD partitions layout.

U-Boot env partition is calculated from CONFIG_ENV_OFFSET option.

First partition contains secure firmware, ARM trusted firmware and U-Boot
with checksums. So it is not possible to replace just one image (e.g.
U-Boot) without updating other parts where is stored checksum of U-Boot.
Therefore there is no extra partition defined for U-Boot and first
partition is called just 'firmware'.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31 14:45:53 +02:00
Pali Rohár
4366082bfe arm: mvebu: Espressobin: Make SPI env offset compatible with Marvell's U-Boot
Espressobin board comes with Marvell's U-Boot version where U-Boot env is
stored in SPI at offset 0x3F0000. This patch changes env offset in
Espressobin defconfig file to match Marvell's U-Boot version.

Users who want to use previous or different env offset can still change it
in .config file when compiling U-Boot.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31 14:45:53 +02:00
Wilson Ding
96fa3c4fda arm: dts: a37x0: enable sd card support on espressobin
Enabled SDIO slot 0 (south bridge) for SD card on
Espressobin board.

Change-Id: I51a2debf9fba276b9c4a2bc6da91328d47f443e3
Signed-off-by: Wilson Ding <dingwei@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/60945
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
[pali: Define cd-gpios and enable CONFIG_DM_REGULATOR_GPIO]
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31 14:45:53 +02:00
Evan Wang
91b85e25b6 mmc: xenon: set signal voltage and max base clock
- The SDIO signal voltage and max base clock frequency
  setting are missing in driver, which causes SDIO
  not working.
- The patch adds SDIO signal voltage switch support,
  which is based on regulator-gpio of vqmmc-supply, and
  sets the max base clock frequency.
- Fix the zero clock value in call to sdhci_setup_cfg()
  function.

Change-Id: I79c8860c65b8db166f4f70db56ede4097f71f1fa
Signed-off-by: Evan Wang <xswang@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/53589
Reviewed-by: Hua Jing <jinghua@marvell.com>
Tested-by: Hua Jing <jinghua@marvell.com>
[pali: Amended fixup patch]
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31 14:45:53 +02:00
Pali Rohár
828d326216 arm64: a37xx: pci: Assert PERST# signal when unloading driver
This change ensures that PCIe card is put into reset state when U-Boot
stops using it.

DM_FLAG_OS_PREPARE ensures that U-Boot executes driver's remove callback
prior booting Linux kernel.

Linux kernel pci-aardvark driver needs to reset PCIe card via PERST# signal
prior initializing it. If it does not issue reset then some PCIe cards
(specially Compex WiFi cards) are not detected at all.

Putting PCIe card into reset state prior booting Linux kernel would ensure
that card would be properly reset at time when Linux kernel starts
initializing pci-aardvark driver.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31 14:45:53 +02:00
Pali Rohár
563b85bd88 arm64: a37xx: pci: Make PCIe Reset GPIO DT compatible with Linux kernel DT
Change active-high to active-low and change DT property name from
reset-gpio to reset-gpios. This format of gpio reset is used by
pci-aardvark driver in Linux kernel.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31 14:45:53 +02:00
Marek Behún
545591132a arm64: dts: armada-3720-espressobin: fix COMPHY nodes
This commit fixes initialization of COMPHY on EspressoBin.

Commit 22f418935b ("phy: marvell: a3700: Use comphy_mux on Armada
37xx.") introduced usage of comphy_mux on Armada 37xx comphy driver.
The lanes are defined in comphy_a3700.c as described in functional
specification, that is:
  lane 0 is SGMII1 or USB3
  lane 1 is PCIe or SGMII0
  lane 2 is SATA or USB3

But the DTS for EspressoBin configures PCIe on lane 0 and USB3 on
lane 1, which is wrong in the sense of the specification and doesn't
work with the comphy_mux code, which is 2 years now (the aardvark driver
causes synchronous abort in U-Boot).

It worked till the above mentioned commit, because the code for powering
up PCIe PHY doesn't work with lane number at all, and the code for
powering up USB3 PHY works differently only if USB3 is on lane 2, ie.
the check goes like:
  if (lane == 2)
    something
  else
    something else
so it does not differentiate between lanes 0 and 1.

In the future I shall post patches that remove the comphy_a3700 driver
and add comphy driver which uses calls to ATF, like Linux' driver does.
This will have the advantage of same DTS bindings as Linux', but till
this is done, we need this patch.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Pali Rohár <pali@kernel.org>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31 14:45:53 +02:00
Pali Rohár
a68676535f arm: mvebu: Espressobin: Enable CONFIG_MVNETA
Espressobin uses mvneta ethernet driver.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31 14:45:53 +02:00
Pali Rohár
48f2c8a37f arm: mvebu: Espressobin: Disallow forwarding packets between wan and lan ports
By default Topaz switch on Espressobin board forwards packets between all
ethernet ports, including CPU (port 0), wan (port 1) and lan (ports 2,3).

This default U-Boot setup is unsuitable for using Espressobin as router as
it opens security hole in forwarding all packets between wan and lan ports.
E.g. dhcp packets from wan network leaks to lan network during small time
window until U-Boot boots Linux kernel which loads network drivers which
disallows forwarding between wan and lan.

This patch fixes above problem. For Espressobin board prior putting Topaz
switch into forwarding mode, Topaz switch is reconfigured to allow
forwarding packets from wan and lan ports only to CPU port. This ensures
that packets from wan port are not forwarded to lan ports and vice-versa.
Packets from CPU port are still forwarded to all other ports, so U-Boot
network boot works with any ethernet port as before.

This problem was already discussed on Espressobin forum [1] and on
Marvell's github issue tracker [2]. As a workaround people on Espressobin
forum patched U-Boot to completely disable lan ports on Topaz switch which
prevented forwarding packets. That workaround had an issue that U-Boot was
unable to netboot via lan ports anymore. Change in this patch does not have
such issue.

This security issue has been dicussed here as well: [3].

[1] - https://web.archive.org/web/20191231164238/http://espressobin.net/forums/topic/boot-behavior-of-the-switch-and-security/
[2] - https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/issues/18
[3] - https://forum.armbian.com/topic/12635-espressobin-uboot-security-concerns-switch-init-portmask/

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31 14:44:14 +02:00
Michal Simek
b892b6d1e0 ti: common: Remove additional i2c read for board detection
There shouldn't be a need to call additional i2c read if above failed
already. Based on comment it should be enough to try to detect legacy
boards which are mentioned in the comment.

Fixes: 2463f6728e ("ti: common: board_detect: Allow DM I2C without CONFIG_DM_I2C_COMPAT")
Fixes: 0bea813d00 ("ARM: omap-common: Add standard access for board description EEPROM")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-08-31 14:40:28 +05:30
Lokesh Vutla
e66ae8e16b arm: dts: k3-am65: Update the RM resource types
Update the ringacc and udma dt nodes to use the latest RM resource types
similar to the ones used in k3-j721e dt nodes.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-08-31 14:39:39 +05:30
Lokesh Vutla
4986b15485 firmware: ti_sci: Drop unused structure ti_sci_rm_type_map
struct ti_sci_rm_type_map is no longer used. Drop its definition and its
declarations.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-08-31 14:39:39 +05:30
Lokesh Vutla
2fe03a1c82 firmware: ti_sci: drop the device ids to resource id translation table
With ABI 3.0, sysfw deprecated special resource types used for AM65x
SoC. Instead started using device id as resource type similar to the
convention used in J721E SOC.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-08-31 14:39:38 +05:30
Tom Rini
9f04a634ef Merge branch '2020-08-27-misc-fixes'
- Fix for gd->ram_top and bootm_size calculations
- Assorted Kconfig entry cleanups / fixes.
- Make checkpatch.pl error on fdt_high/initrd_high=0xffffffff
- Resync scripts/setlocalversion
- Other minor bugfixes
2020-08-28 08:51:37 -04:00
Rasmus Villemoes
2ed1b242ab scripts/setlocalversion: sync with linux 5.8
The linux changes since v3.16 are

78283edf2c01 kbuild: setlocalversion: print error to STDERR
b24413180f56 License cleanup: add SPDX GPL-2.0 license identifier to files with no license
6147b1cf1965 scripts/setlocalversion: git: Make -dirty check more robust
8ef14c2c41d9 Revert "scripts/setlocalversion: git: Make -dirty check more robust"
ff64dd485730 scripts/setlocalversion: Improve -dirty check with git-status --no-optional-locks
7a82e3fa28f1 scripts/setlocalversion: clear local variable to make it work for sh
991b78fbd223 scripts: setlocalversion: fix a bashism
3c96bdd0ebfa scripts: setlocalversion: replace backquote to dollar parenthesis

and it's ff64dd485730 that is the motivation for this sync. It fixes
false positive "-dirty" added to the version string when building with
Yocto
(https://lists.openembedded.org/g/openembedded-core/message/137702).

There has been one U-Boot specific patch since this was synced with
linux 3.16: 81630a3b38 (scripts: setlocalversion: safely extract
variables from auto.conf using awk).  Keep these changes applied.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
[trini: Re-add 81630a3b38 and reword message]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-27 15:55:18 -04:00
Baruch Siach
7f98b4eeee image: don't exceed gd->ram_top in bootm_size
When board_get_usable_ram_top() limits gd->ram_top, env_get_bootm_size()
must not exceed that limit. Otherwise, boot_relocate_fdt() might put fdt
out of the allowed RAM range.

The similar commit 8ce1f10cf2 ("ARM: bootm: take into account
gd->ram_top") exposed this bug.

This fixes boot on Armada 8040 based Clearfog GT-8K where ram_top is set
to 0x80000000 (2GB), but bi_dram[0].size might be up to 0xc0000000
(3GB). Note the relocated fdt address (0xbfff4000) in the console output
listed below:

Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
62 bytes read in 21 ms (2 KiB/s)
1:	linux
Retrieving file: /extlinux/Image
13740544 bytes read in 1266 ms (10.4 MiB/s)
Retrieving file: /extlinux/armada-8040-clearfog-gt-8k.dtb
33368 bytes read in 31 ms (1 MiB/s)
   Booting using the fdt blob at 0x4f00000
   Loading Device Tree to 00000000bfff4000, end 00000000bffff257 ... "Synchronous Abort" handler, esr 0x96000045
elr: 000000000006e1cc lr : 0000000000068fd8 (reloc)
elr: 000000007ffa91cc lr : 000000007ffa3fd8
x0 : ffffffffffffffff x1 : 00000000bfffc258
x2 : 0000000000000000 x3 : ffffffffffff7da7
x4 : 0000000004f08258 x5 : 00000000bfff4000
x6 : 00000000bfff4000 x7 : 000000000000000f
x8 : 000000007fb23bf8 x9 : 0000000000000008
x10: 00000000bffff257 x11: 00000000bffff257
x12: 0000000000000000 x13: fffffffffffff000
x14: 00000000bfff4000 x15: 0000000000000021
x16: 000000007ff7bc38 x17: 0000000000000000
x18: 000000007fb2add0 x19: 00000000bfff4000
x20: 0000000004f00000 x21: 000000000000b258
x22: 0000000058820000 x23: 0000000000000010
x24: 000000007ffe3c40 x25: 000000007fb23cb8
x26: 00000000c0000000 x27: 0000000000000000
x28: 000000007fc3fd50 x29: 000000007fb23bd0

Code: 54000061 aa0603e0 d65f03c0 38606882 (38206822)
Resetting CPU ...

Thanks to Patrice CHOTARD who directed me to the right way.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2020-08-27 11:26:58 -04:00
Michal Simek
0b2b9b85d0 cmd: mem: Remove already removed CONFIG_SYS_MEMTEST_SCRATCH
The commit e519f03a18 ("cmd: mem: Remove CONFIG_SYS_MEMTEST_SCRATCH
mapping") removed CONFIG_SYS_MEMTEST_SCRATCH but commit 0914011310
("command: Remove the cmd_tbl_t typedef") has added it back. That's why
symbol is still in the tree that's why remove it again.

Fixes: 0914011310 ("command: Remove the cmd_tbl_t typedef
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-08-27 11:26:58 -04:00
Heinrich Schuchardt
de95930946 lib/rsa: correct check after allocation in fdt_add_bignum()
After allocating to pointer ctx we should check that pointer and not
another pointer already checked above.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-08-27 11:26:58 -04:00
Heinrich Schuchardt
4431a9889c test: undefined reference to 'sscanf'
Compiling with CONFIG_UNIT_TEST=y leads to:

aarch64-linux-gnu-ld.bfd:
test/lib/sscanf.c:50: undefined reference to `sscanf'

Add missing build dependency.

Fixes:e87dfb0526be ("lib: sscanf: add sscanf implementation")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-08-27 11:26:58 -04:00
Tom Rini
12178b51c2 checkpatch.pl: Make fdt / initrd relocation disabling an error
Entirely disabling relocation of the device tree or initrd is almost
never the right answer.  Doing this by default leads to hard to diagnose
run-time failures.

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-27 11:26:58 -04:00
Michal Simek
076617847a env: Kconfig: Add missing dependency for ENV_IS_IN_EXT4
ENV_IS_IN_EXT4 also need to enable FS_EXT4 which is not covered in Kconfig.
Kconfig reports this as:
WARNING: unmet direct dependencies detected for EXT4_WRITE
  Depends on [n]: FS_EXT4 [=n]
  Selected by [y]:
  - ENV_IS_IN_EXT4 [=y] && !CHAIN_OF_TRUST [=n]

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2020-08-27 11:26:58 -04:00
Michal Simek
7b56432c7b arc: Kconfig: Add missing DM dependency
ARC is selecting TIMER which depends on DM but DM is not selected and
doesn't need to be enabled. Fix it by selecting DM for ARC architecture.

Kconfig is showing this missing dependency by:
WARNING: unmet direct dependencies detected for TIMER
  Depends on [n]: DM [=n]
  Selected by [y]:
  - ARC [=y] && <choice>

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-08-27 11:26:58 -04:00
Michal Simek
6e741cfa93 cmd: Kconfig: Change dependency for CMD_ADC
CMD_ADC selected DM_REGULATOR unconditionally without enabling DM.
That's why change select to depends on to cover it.

Kconfig is showing this issue as:
WARNING: unmet direct dependencies detected for REGMAP
  Depends on [n]: DM [=n]
  Selected by [y]:
  - DM_REGULATOR_PBIAS [=y] && DM_REGULATOR [=y]

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Update CMD_ADC=y configs to enable DM_REGULATOR now]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-27 11:26:39 -04:00
Michal Simek
a261fdce38 pci: kconfig: Setup proper dependency for PCIE_ROCKCHIP
There is missing dependency for PCIE_ROCKCHIP which selects
PHY_ROCKCHIP_PCIE which directly depends on ARCH_ROCKCHIP.

WARNING: unmet direct dependencies detected for PHY_ROCKCHIP_PCIE
  Depends on [n]: ARCH_ROCKCHIP [=n]
  Selected by [y]:
  - PCIE_ROCKCHIP [=y] && PCI [=y]

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2020-08-27 11:20:33 -04:00
Ruben Di Battista
67e62c7468 drivers: usb: Fix config indentation
The indentation was messing up with the scripts/build-whitelist.sh that
was marking SYS_USB_EVENT_POLL_VIA_INT_QUEUE (and probably also the
other indented options) erroneously as ad-hoc configure option with the
following error:

```
Error: You must add new CONFIG options using Kconfig
The following new ad-hoc CONFIG options were detected:
CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE
```
2020-08-27 11:20:33 -04:00
Tom Rini
f87c80ade3 Prepare v2020.10-rc3
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-26 17:30:22 -04:00
Tom Rini
d86bf9124f configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-26 17:26:24 -04:00
Tom Rini
7a1a01c602 For 2020.10
-----------
 
 - mx6: SOCs user selectable
        Fix for imx6q_logic
        Some DM conversion
 - mx7: introduce secondary boot device
 
 Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/720918010
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCX0UiVw8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76bhlACgj8NxL/lQcxfcaI4Dwfic5Mz5EiwAnihxUGff
 KQdAHwZpCj4NOby3VRGz
 =BI7Q
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20200825' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

For 2020.10
-----------

- mx6: SOCs user selectable
       Fix for imx6q_logic
       Some DM conversion
- mx7: introduce secondary boot device

Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/720918010

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-25 23:12:43 -04:00
Tom Rini
9f9ecd3e4d Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell
- Add basic Marvell/Cavium OcteonTX/TX2 support (Suneel)
- Infrastructure changes to PCI uclass to support these SoC's (Suneel)
- Add PCI, MMC & watchdog driver drivers for OcteonTX/TX2 (Suneel)
- Increase CONFIG_SYS_MALLOC_F_LEN for qemu-x86 (Stefan)
2020-08-25 13:38:29 -04:00
Tom Rini
ec54217ddc Merge tag 'i2c-bugfixes-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c
i2c bugfixes for v2020.10
- fix some issues with octeon_i2c driver on ARM Octeon TX2
- fix link failure with CONFIG_SPL and CONFIG_I2C_MUX_PCA954x
2020-08-25 08:19:41 -04:00
Tom Rini
e49a9d4ddb Merge tag 'u-boot-rockchip-20200820' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Fix rk3399 evb sdcard support
- Fix for SPL_LED support
2020-08-25 08:19:14 -04:00
Tom Rini
078656186f Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscv
- Sipeed Maix support S-mode.
- Provide command sbi.
- Use fdtdec_get_addr_size_auto_parent to get fu540 cache base address.
- Fix a compiler error with CONFIG_SPL_SMP=n.
- Fix sifive ram driver 32 compiler warnings.
- Fix kendryte/pll.h redefine nop() warning.
2020-08-25 08:18:50 -04:00
Tom Rini
8ee3a24fdc Merge branch '2020-08-24-misc-improvements'
- Squashfs compression support
- Coverity fixes
- XEN guest updates
- Finish previous MediaTek updates
- Arm Total Compute platform support
2020-08-25 08:12:05 -04:00
Stefan Roese
6944937f9c x86: qemu-x86_defconfig: Increase CONFIG_SYS_MALLOC_F_LEN
With the upcoming increase of the malloc area in U-Boot
("pci: pci-uclass: Dynamically allocate the PCI regions"), the CI QEMU
x86 test fails:

U-Boot 2020.10-rc2-g0a668f6d38 (Aug 25 2020 - 06:12:51 +0000)

alloc space exhausted
Error binding driver 'cpu_qemu': -12
Some drivers failed to bind
alloc space exhausted
initcall sequence fff6a760 failed at call fff13b3d (err=-19)

This patch now increases CONFIG_SYS_MALLOC_F_LEN to 0x1000, which is
already used on qemu-x86_64_defconfig.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
2020-08-25 11:37:57 +02:00
Grygorii Tertychnyi
acbc1d86f1 imx8m: config: convert to bootm_size
Restrict the memory range available for image processing in the
"bootm" to 256 MiB so the kernel can access it and FDT or initrd are
not overwritten on ARM64.

Signed-off-by: Grygorii Tertychnyi <grygorii.tertychnyi@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2020-08-25 10:26:38 +02:00
Adam Ford
74d8f9d562 ARM: imx6q_logic: Fix broken booting by moving fdt_addr_r address
The loading address is too close to the kernel address, so newer kernels
may overlap memory space, so loading the device tree may corrupt zImage.

This patch moves the fdt_addr_r to 0x14000000 which is also consistent
with guidance that the kernel be allocated 32MB.  This places it
in the same place as the ramdisk, so this patch moves the ramdisk address
512KB after the fdt.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-08-25 10:26:31 +02:00