Add power_domain_lookup_name interface to power domain uclass to find
a power domain device by its DTB node name, not using its associated
client device.
Through this interface, we can operate the power domain devices directly.
This is needed for non-DM drivers.
Modified from Ye's NXP downstream patch
only for legacy imx8 power domain driver, since we have not migrated
to use new power domain driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beacon EmbeddedWorks, formerly known as Logic PD, is releasing
a devkit based on the i.MX8M Mini SoC consisting of baseboard +
SOM.
It supports eMMC on the SOM, microSD on the baseboard, various
GPIO, the PINCTRL, and UART.
Signed-off-by: Adam Ford <aford173@gmail.com>
enable the GPMI NAND driver for i.MX8, i.MX8 use similar controller as
i.MX8M
- register definition for i.mx8
- DMA structure must be 32bit address
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the gpmi/apbh_dma/bch drivers and relevant registers for i.MX8M.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is a porting of
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/
commit/?h=imx_4.1.15_1.0.0_ga&id=e4dacc44d22e9474ec456cb330df525cd805ea38
"
i.MX6QP and i.MX7D BCH module integrated a new feature to detect the
bitflip number for erased NAND page. So for these two platform, set the
erase threshold to gf/2 and if bitflip detected, GPMI driver will
correct the data to all 0xFF.
Also updated the imx6qp dts file to ditinguish the GPMI module for i.MX6Q
with the one for i.MX6QP.
"
In this patch, i.MX6UL is added and threshold changed to use ecc_strength.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
So far u-boot only load SNSR25C for TMU main probe (probe 0). However,
kernel enables two probes. So it also needs to set default SNSR25C of
TCALIV1 for blank samples.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MP thermal which has two probes and supports temperature range
from -40 to 125. The driver still uses default 1p HW
calibration at 25C and loads calibration parameters from fuse.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Like iMX8MM, iMX8MN also needs SW to load TMU TASR and TCALIV registers
value from fuse before enabling TMU calibration. Otherwise the calibration
is not exact.
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On iMX8MM, the default value of TMU registers TCALIV and TASR need
be loaded from fuse. HW won't do this, it expect SW loads them before
using TMU.
Reviewed-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
imx_get_mac_from_fuse is used to load MAC address from fuse. On imx8mp,
we have two different ENET controllers and both need to call this
function. So decouple its declare from fec driver.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There are different parts from one SoC. Take i.MX6ULL for example,
some part might not have ENET, some might have; some might not have
USB, some might have. The information could be got from OCOTP,
to make one image support the different parts, we need runtime
disable linux kernel dts node and uboot driver probe if the
corresponding module not exists in the part.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier
board. Currently working is ethernet, serial, eMMC. DT is imported
from Linux 5.4.28 ("462afcd6e7ea") .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
If dcache is switched OFF to ON state and if non-cached memory is
used, this non-cached memory must be re-declared as uncached to mmu
each time dcache is set ON.
Introduce noncached_set_region() to set this non-cached region's mmu
settings. Let architecture override it by defining it as a weak
function.
For ARM architecture, noncached_set_region() defines all noncached
region as non-cacheable.
Issue found on STM32MP1 platform using dwc_eth_qos ethernet driver,
when going from dcache OFF to dcache ON state, ethernet driver issued
TX timeout errors when performing dhcp or ping.
It can be reproduced with the following sequence:
dhcp
while true ; do
ping 192.168.1.300 ;
dcache off ;
ping 192.168.1.300 ;
dcache on ;
done
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The Juno board features a standard compliant EHCI/OHCI USB host
controller pair, which we can just enable.
The platform data is taken from the device tree.
This allows to use USB mass storage (the only storage on a Juno r0)
for loading.
At least on my board USB seems a bit flaky, I need two "usb reset"
sequences after the "usb start" to detect an USB hard drive.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
So far the Juno board wasn't implementing reset. Let's just use the
already existing PSCI_RESET based method to avoid any extra code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Arm Juno board was still somewhat stuck in "hardcoded land", even
though there are stable DTs around, and one happens to actually be on
the memory mapped NOR flash.
Enable the configuration options to let the board use OF_CONTROL, and
add a routine to find the address of the DTB partition in NOR
flash, to use that for U-Boot's own purposes.
This can also passed on via $fdtcontroladdr to any kernel or EFI
application, removing the need to actually load a device tree.
Since the existing "afs" command and its flash routines require
flash_init() to be called before being usable, and this is done much
later in the boot process, we introduce a stripped-down partition finder
routine in vexpress64.c, to scan the NOR flash partitions for the
DT partition. This location is then used for U-Boot to find and probe
devices.
The name of the partition can be configured, if needed, but defaults
to "board.dtb", which is used by Linaro's firmware image provided.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
- dts clean up to use -u-boot for px30, rk3399 boards
- dts sycn from upstream kernel for rk3328, rk3399
- add rockchip rng driver
- new board support: rk3328-roc-cc, rk3399-roc-pc,Nanopi M4 2GB
This resolves issues with certain SFP modules.
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Add REVC informaiton.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The correct syntax is 'select SYS_...' and not 'select CONFIG_SYS...'
Fixes: d5c819b885 ("actions: Move defconfig options to Kconfig")
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_SPL_FAT_SUPPORT was removed in commit 0c3a9ed409
("spl: Kconfig: Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT").
Fixup a leftover use of the symbol.
Fixes: 9d86dbd9cf ("imx: spl: implement spl_boot_mode for i.MX7/8/8M")
Signed-off-by: Harald Seiler <hws@denx.de>
It is hard to read code which contains nested ifdef blocks. Replace
them with normal if-blocks and the IS_ENABLED() macro. This is not only
more readable but also helps as both arms are validated by the compiler
in all cases.
Signed-off-by: Harald Seiler <hws@denx.de>
The CONFIG_SPL_FORCE_MMC_BOOT config flag is not needed as its behavior
is the correct one in all cases; using spl_boot_device() instead of the
boot_device parameter will lead to inconsistency issues, for example,
when a board_boot_order() is defined. In fact, this is the reason the
parameter was introduced in the first place, in commit 2b1cdafa9f
("common: Pass the boot device into spl_boot_mode()").
This reverts commit 772b55723b.
Link: https://lists.denx.de/pipermail/u-boot/2020-April/405979.html
Signed-off-by: Harald Seiler <hws@denx.de>
Boards may extend or re-define the boot list in their board_boot_order()
function by modifying spl_boot_list. E.g. a board might boot SPL from a
slow SPI NOR flash and then load the U-Boot from an eMMC or SD-card.
Or it might use additional MMC boot device in spl_boot_list for cases
when the image in SPI NOR flash is not found, so it could fall back to
eMMC, SD-card or another boot device.
Getting the MMC boot mode in spl_mmc will fail when we are trying to
boot from an MMC device in the spl_boot_list and the original board
boot mode (as returned by spl_boot_device()) is not an MMC boot mode.
Fix it by checking the asked MMC boot device from the spl_mmc_boot_mode()
argument.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
initr_enable_interrupts() is an ARM-specific wrapper over
enable_interrupts(), which is run during the common init sequence. It can
be eliminated by moving the enable_interrupts() call to the end of
interrupt_init() function, in arch/arm/lib/interrupts*.c.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Solved the overflow on phys_addr_t type for start + size in
mmu_set_region_dcache_behaviour() function.
This overflow is avoided by dividing start and end by 2 before addition,
and we only expecting that start and size are even.
This patch doesn't change the current function behavior if the
parameters (start or size) are not aligned on MMU_SECTION_SIZE.
For example, this overflow occurs on ARM32 with:
start = 0xC0000000 and size = 0x40000000
then start + size = 0x100000000 and end = 0x0.
For information the function behavior change with risk of regression,
if we just shift start and size before the addition.
Example with 2MB section size:
MMU_SECTION_SIZE 0x200000 and MMU_SECTION_SHIFT = 21
with start = 0x1000000, size = 0x1000000,
- with the proposed patch, start = 0 and end = 0x1 as previously
- with the more simple patch:
end = (start >> MMU_SECTION_SHIFT) + (size >> MMU_SECTION_SHIFT)
the value of end change:
start >> 21 = 0, size >> 21 = 0 and end = 0x0 !!!
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the new flags DCACHE_DEFAULT_OPTION to define the default
option to use according the compilation flags
CONFIG_SYS_ARM_CACHE_*.
This new compilation flag allows to simplify dram_bank_mmu_setup()
and can be used as third parameter (option=dcache option to select)
of mmu_set_region_dcache_behaviour function.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add protection in dram_bank_mmu_setup() to avoid access to bd->bi_dram
before relocation.
This patch allow to use the generic weak function dram_bank_mmu_setup
to activate the MMU and the data cache in SPL or in U-Boot before
relocation, when bd->bi_dram is not yet initialized.
In this cases, the MMU must be initialized explicitly with
mmu_set_region_dcache_behaviour function.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Move CONFIG_SYS_ARM_CACHE_WRITETHROUGH and
CONFIG_SYS_ARM_CACHE_WRITEALLOC into Kconfig done by moveconfig.py.
Kconfig uses a choice between the 3 values supported in U-Boot,
including the new configuration CONFIG_SYS_ARM_CACHE_WRITEBACK
(the default configuration).
The patch also avoids to select simultaneously 2 configurations.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add initial support for Google's Coral Dev Board based on i.MX8MQ.
https://coral.ai/products/dev-board
The Phanbell naming has been used here to match the naming convention
used in Google's U-Boot source tree:
https://coral.googlesource.com/uboot-imx/
Co-developed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Tested-by: Marco Franchi <marcofrk@gmail.com>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
imx8m has the only implementation of reset_cpu() which does not ignore
the addr parameter and instead gives it some meaning as the base address
of watchdog registers. This breaks convention with the rest of U-Boot
where the parameter is ignored and callers are passing in 0.
Fixes: d2041725e8 ("imx8m: restrict reset_cpu")
Co-developed-by: Harald Seiler <hws@denx.de>
Signed-off-by: Harald Seiler <hws@denx.de>
Signed-off-by: Claudius Heine <ch@denx.de>
The SPL can also be compiled with sysreset drivers just fine, so
update the condition to cater for that option.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
If the cpu-idle-states is missing from the DT in the first place, do
not fail on removing in. Just move on and do not even print an error,
since not being able to remove something which is not there in the
first place is not an error and surely does not justify failing to
boot.
Turn the surrounding prints into debugs to reduce the useless noise.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This patch synchronizes the device tree with that from 5.6.7.
This also adds nodes for crypto and ddrc, which makes keeping
the device tree files from individual boards in sync with the
Linux kernel. This is helpful when boads reference those nodes.
Signed-off-by: Adam Ford <aford173@gmail.com>
imx8m has the only implementation of `reset_cpu` which does not ignore
the addr parameter and instead gives it some meaning as the base address
of watchdog registers. This breaks convention with the rest of U-Boot
where the parameter is ignored and callers are passing in 0.
Fixes: d2041725e8 ("imx8m: restrict reset_cpu")
Co-Authored-by: Harald Seiler <hws@denx.de>
Signed-off-by: Claudius Heine <ch@denx.de>
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
In case CONFIG_SYSRESET is set, do_reset from reset.c will not be available
anywere, even if SYSRESET is disabled for SPL/TPL.
'do_reset' is called from SPL for instance from the panic handler and
PANIC_HANG is not set
Signed-off-by: Claudius Heine <ch@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a module to configure the tamper and secure violation of
the SNVS using the SCU API.
The module also adds some commands:
- snvs_cfg: Configure the SNVS HP and LP registers
- snvs_dgo_cfg: Configure the SNVS DGO bloc if present (8QXP)
- tamper_pin_cfg: Change the configuration of the tamper pins
- snvs_clear_status: Allow to write to LPSR and LPTDSR to clear
status bits
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
