Commit Graph

30832 Commits

Author SHA1 Message Date
Heiko Schocher
09c3280754 mtd, nand: Move common functions from cmd_nand.c to common place
Move common functions from cmd_nand.c (for calculating offset
and size from cmdline paramter) to common place, so they could
used from other commands which use mtd partitions.

For onenand the arg_off_size() is left in common/cmd_onenand.c.
It should use now the common arg_off() function, but as I could
not test onenand I let it there ...

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
2015-06-30 00:40:11 +05:30
Daniel Schwierzeck
9fe6d8716e mtd, spi: Add MTD layer driver
Add MTD layer driver for spi, original patch from:
http://git.denx.de/?p=u-boot/u-boot-mips.git;a=commitdiff;h=bb246819cdc90493dd7089eaa51b9e639765cced

Changes from Heiko Schocher against this patch:
- Remove compile error if not defining CONFIG_SPI_FLASH_MTD:

  LD      drivers/mtd/spi/built-in.o
drivers/mtd/spi/sf_probe.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
drivers/mtd/spi/sf_ops.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
make[1]: *** [drivers/mtd/spi/built-in.o] Fehler 1
make: *** [drivers/mtd/spi] Fehler 2

- Add a README entry.
- Add correct writebufsize, to fit with Linux v3.14
  MTD, UBI/UBIFS sync.

Note (From Jagan): For testing raw mtd parition erase/read/write operations
using cmd_sf, sf_mtd should be required to register the spi flash device to
MTD layer but the sf_mtd_info ops were not required until and unless if we
use any flash filesystem layer say for example UBI. Due to this the foot-print
got increased ~290bytes in non-UBI case here that should be acceptible.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
2015-06-30 00:40:11 +05:30
Haikun Wang
ecfbaa869a defconfig: ls1021a: Add OF_CONTROL and DM support
PI and QSPI only work when boot from QSPI on ls1021a.
This patch only enable options in qspi boot defconfig.

Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-06-30 00:40:11 +05:30
Haikun Wang
9dd3d3c00c arm: ls102xa: Enable Driver Model SPI for ls1021atwr
Enable Driver Model SPI for ls1021atwr board.
DSPI and QSPI only be enabled when boot from QSPI.
DSPI and QSPI are compatible under Driver Model SPI.

Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-06-30 00:40:11 +05:30
Haikun Wang
e5493d4e49 arm: ls102xa: Enable Driver Model SPI for ls1021aqds
Enable Driver Model SPI for ls1021aqds board.
DSPI and QSPI is enabled only when boot from QSPI.
DSPI and QSPI are compatible under Driver Model SPI.

Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-06-30 00:40:10 +05:30
Haikun Wang
69a27ea80b dm: ls1021aqds: dts: Use "spi_dataflash" driver instead of "spi_flash_std" for DSPI flash
The type of DSPI flash on ls1021aqds is AT45DB021, it has specail
commands and page-size.
Use the special spi flash driver instead of "spi_flash_std" driver.

Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-06-30 00:40:10 +05:30
Haikun Wang
79b4c08fc4 dm: sf: Add Atmel DataFlash spi flash driver
Atmel DataFlash chips have commands different from common spi
flash commands.
Atmel DataFlash also have special page-size.
This driver add support for accessing Atmel DataFlash.
It is based on the Driver Model.
Example:
=> sf probe 1:0
SPI DataFlash: Detected AT45DB021B with page size 264 Bytes, erase size 264 Bytes, total 264 KiB, revision d
=> sf erase 0 42000
SF: 270336 bytes @ 0x0 Erased: OK
=> mw.l 82000000 45444342 20000
=> sf write 82000000 0 42000
SF: 270336 bytes @ 0x0 Written: OK
=> sf read 83000000 0 42000
SF: 270336 bytes @ 0x0 Read: OK
=> cmp.b 82000000 83000000 42000
Total of 270336 byte(s) were the same

Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chakra Divi <cdivi@openedev.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-06-30 00:40:10 +05:30
Tom Rini
7853d76b0b Merge git://git.denx.de/u-boot-marvell 2015-06-28 16:31:32 -04:00
Kevin Smith
3fd38af704 db-88f6820-gp.h: Load data blobs into lower memory
By default on this platform, u-boot loads data into high memory
in the range of 0x7Fxxxxxx, which generates a data abort when the
kernel tries to read it.  Config the u-boot environment to load
the device tree and initrd image into lower memory to make them
accessible to the kernel.

Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
2015-06-28 17:52:41 +02:00
Kevin Smith
ae68763b6d mv-common.h: Include support for device trees
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
2015-06-28 17:52:41 +02:00
Ian Campbell
da9971d1b3 Revert "sunxi/nand: Add support to the SPL for loading u-boot from internal NAND memory"
This reverts commit f76eba38b3.

This patch did not have a full and proper copyright/S-o-b chain.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>

Conflicts:
	include/configs/sun6i.h
	include/configs/sun8i.h
2015-06-28 11:46:31 -04:00
Joe Hershberger
ef0f2f5752 Move defaults from config_cmd_default.h to Kconfig
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-25 22:18:34 -04:00
Joe Hershberger
c9bb942e2f Move default y configs out of arch/board Kconfig
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.

Remove the configs that behave this way from the archs.

A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:

SPIFLASH
DISPLAY_BOARDINFO

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-25 22:17:55 -04:00
Joe Hershberger
3c85c8b9f9 a3m071: Add needed dependency on LIB_RAND
Boards using link-local need lib rand.

When link-local is moved to Kconfig, this dependency will be described
there.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2015-06-25 17:05:05 -04:00
Joe Hershberger
6aab5ae921 common: Add the CMD_ENV_EXISTS config to Kconfig
This command needs to exist in the Kconfig so that it can be moved from
the config_cmd_default.h.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2015-06-25 17:04:51 -04:00
Joe Hershberger
f38bec9f15 common: Fix comment for saveenv in Kconfig
The help for this was simply copied from another command.

Update it to reflect the command.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2015-06-25 17:04:47 -04:00
Joe Hershberger
22e04faaab mtd: spi: Add the SPI_FLASH config to Kconfig
This config needs to be available in the Kconfig to allow it to be
removed from arch defaults.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2015-06-25 17:04:43 -04:00
Marek Vasut
9f1b4456c9 mmc: bcm2835_sdhci: Restore original delay behavior
Patch 33fe2fb8df titled
"mmc: bcm283x: Remove get_timer_us() from mmc driver"
incorrectly replaced ad-hoc get_timer_us() function
with a plain get_timer(). The get_timer() operates in
mSec units instead of uSec though, which caused very
slow operation of the driver.

Restore the original behavior of the driver, but avoid
get_timer_us() and use timer_get_us() instead. The later
is part of the standard API.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jakub Kiciński <moorray3@wp.pl>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Jakub Kicinski <kubakici@wp.pl>
2015-06-25 17:04:37 -04:00
Tom Rini
325849ff3d Merge git://git.denx.de/u-boot-usb 2015-06-19 16:46:51 -04:00
Heiko Schocher
8c65a2fae8 siemens,am33x,thuban: rename dxr2 to thuban
Update new naming scheme.

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-19 16:46:50 -04:00
Heiko Schocher
578056c35d siemens,am33x,rastaban: add rastaban config
rastaban is a draco version with more flash, more RAM
and faster CPU. Number of partitions is the same but
rootfs partition is different.

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-19 16:46:50 -04:00
Chris Packham
3b10cf120b README: Describe CONFIG_SYS_NO_FLASH
Unlike most configuration options defining this actually disables
support for a feature (parallel flash). Eventually the logic behind this
should probably be flipped so that '#ifndef CONFIG_SYS_NO_FLASH' becomes
'#ifdef CONFIG_HAS_PARALLEL_FLASH' but for now lets document the
existing behaviour.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2015-06-19 16:46:50 -04:00
Lokesh Vutla
334bbb387f ARM: BeagleBoard-X15: Enable VTT regulator
BeagleBoard-X15 uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-19 16:46:49 -04:00
Mugunthan V N
f4787eab13 am43xx_evm: add eth boot support
add cpsw ethernet boot mode support to download spl and
u-boot.img via tftp protocol. Also adding a seperate config
for ethernet boot mode as the default build falcon mode and
environment on MMC is defined for ethernet boot mode
environment should be set to nowhere.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-19 16:46:49 -04:00
Mugunthan V N
aee119bd70 am43xx_evm: add usb host boot support
While booting via usb host mode, ROM uses DMA to copy MLO over USB so
ARM internal RAM cannot be used. Adding USB host boot support by
introducing new config target which sets SPL_TEXT_BASE to OCMC ram.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-19 16:46:49 -04:00
Tom Rini
46a14a6383 am43xx: Update CONFIG_SPL_TEXT_BASE
With 1.2 silicon this is now the documented starting usable point for
downloading images to (and corrects a problem with peripheral booting
with prior silicon).  Prior silicon is OK using this address as well.

Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-06-19 16:46:49 -04:00
Nishanth Menon
67055bee25 ARM: DRA7: Change configuration to prevent DDR reset control from EMIF
DRA7/AM57xx devices can be operated in many different configurations.
When the SoC is supposed to support a configuration where low power mode
state may involve the SoC completely powered off and DDR is in self
refresh, SoC EMIF controller should not be the master of the reset
signal and an external entity might be in control of things.

The default configuration of Linux on TI evms involve not powering off
the voltage rails (due to various reasons including reliability concerns)
and must not allow DDR reset to be controlled by EMIF. On platforms
where external entity might control the reset signal, this configuration
will be a "dont care".

Fixes: 536d874708 ("ARM: DRA7: Update DDR IO registers")
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-19 16:46:48 -04:00
Guillaume GARDET
3683c3d1f7 ti: omap4: remove CONFIG_SPL_EXT_SUPPORT from ti_omap4_common.h since it is now in ti_armv7_common.h
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-19 16:46:48 -04:00
Guillaume GARDET
bd2c4522c2 ti: armv7: enable EXT support in SPL (using ti_armv7_common.h)
Tested on Pandaboard (rev. A3) and Beagleboard xM (rev. B).
Compilation tested on TI armv7 boards and OMAP boards from other vendors.

Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-19 16:46:48 -04:00
Heiko Schocher
61159b7684 arm, am33xx: update for siemens am335x based boards
updates for the siemens am335x based boards:

- draco: add delay for DDR3 configuration
- change MTD partition layout and add a possibility
  to redefine MTD layout in board header.
- move ubi support to common header file
- draco: improve dtb naming
- draco: set CONFIG_SYS_CBSIZE to 1024
- add generic env based led
  Leds can now be defined in Environment
- add generic env based dfu button
  Which gpio is used for the dfu button can be defined
  through the Environment
- set MACH_TYPE only if defined
- draco: increase CPU freq to 300MHz
- Add time command to siemens am33xx boards
- DDR3: increase default tRFC
- draco: enable pullup for DFU and ERST pin
- change print format DDR3

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>

Signed-off-by: Heiko Schocher <hs@denx.de>
2015-06-19 16:46:47 -04:00
Paul Kocialkowski
8607c4f127 common: cmd_part: start and size sub-commands introduction
This introduces the part start and part size sub-commands. The purpose of these
is to store the start block and size of a partition in a variable, given the
device and partition number.

This allows reading raw data that fits a single partition more easily.
For instance, this could be used to figure out the start block and size of a
kernel partition when a partition table is present, given the partition number.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Stephen Warren <swarren@nvidia.com>
[trini: Change "%lx" to LBAF]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-19 16:46:47 -04:00
Paul Kocialkowski
a78f78ebeb common: cmd_part: Proper alignment
This fixes a misaligned declaration.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-06-19 16:46:47 -04:00
Vitaly Andrianov
437a7293a7 keystone2: use correct EFUSE_BOOTROM fileds to configure speed
The get_max_arm_speed() and get_max_dev_speed() used wrong register
fields to get the maximum speeds. This commit fixes the bug.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-19 16:46:46 -04:00
Hans de Goede
de451493f1 usb: kbd: Disable idle input reports when we do not need them
When we're polling and thus handling key-repeat in software, make sure
to disable idle reports, some keyboards may have these enabled by default
messing up our software keyrepeat.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-06-19 14:33:29 +02:00
Hans de Goede
7f59d16a50 usb: ehci: Properly deal with data toggle for interrupt endpoints
Without this we loose every other interrupt packet. We never noticed this
because with keyboards the packets which we were loosing would normally
be key release packets.

But now that we do keyrepeat in software instead of relying on the hid
idle functionality, missing a release will result in key repeat triggering.

This commit fixes this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-06-19 14:33:28 +02:00
Hans de Goede
b335fe6810 usb.h: Always declare usb function prototypes
There is no harm in declaring the function prototypes even if nothing
implements them, and when CONFIG_DM_USB=y the various usb functions are
available regardless of any controller drivers being enabled.

This fixes compile warnings due to missing prototypes on ARCHs where
the ARCH Kconfig always enables CONFIG_DM_USB and various usb drivers.

One could argue that in the case of no controllers CONFIG_DM_USB should not
be set, but this problem is typically seen during bringup of boards which
do actually have usb controllers.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-06-19 14:32:12 +02:00
Tom Rini
c6265f7f34 CPCI4052: Remove CONFIG_SYS_LONGHELP
With the change to make sure that CONFIG_CMD_NET is enabled this board
no longer fits into the linker script:

powerpc-linux-ld.bfd: section .resetvec loaded at [fffffffc,ffffffff] overlaps section .u_boot_list loaded at [ffffff58,00000723]
powerpc-linux-ld.bfd: u-boot: section .resetvec lma 0xfffffffc adjusted to 0x724
powerpc-linux-ld.bfd: u-boot: section `.resetvec' can't be allocated in segment 0
LOAD: .data.init .text .rodata .reloc .data .u_boot_list .resetvec
powerpc-linux-ld.bfd: final link failed: File truncated

Drop CONFIG_SYS_LONGHELP to free up space.

Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-18 16:19:00 -04:00
Paul Kocialkowski
3ae8f4c8ae spl: spl_mmc: MMC boot mode provisions checks
This allows using only one of either raw or fs mode for SPL mmc boot, without
the need to have provisions for the other. In particular, a device may have
U-Boot installed on a file system on the mmc, without ever needing to read
U-Boot from raw memory. Thus, there is no reason to provide a sector or
partition for raw mode. This allows this behaviour and still provides a robust
fallback mechanism in case provisions for both modes are defined.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-06-18 16:11:42 -04:00
Paul Kocialkowski
1ec264695f spl: spl_mmc: Minor cosmetics
This switches some printf calls to puts and avoids a test repetition.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-06-18 16:11:42 -04:00
Peter Robinson
0b367380a5 tools/env/fw_env.h: Correct include order
When building tools-only (or env) we need to be sure that we do use
<linux/kconfig.h> and do not use <generated/autoconf.h>.  This will fix
problems such as running 'make defconfig' or 'make sandbox_config' and
then 'make tools-only'.

Based on the responses below to the thread add linux/kconfig.h higher in
the includes and drop the now unneeded autoconf.h lower down to ensure
the default environment is included correctly

http://lists.denx.de/pipermail/u-boot/2015-June/216849.html

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
2015-06-18 16:11:42 -04:00
Łukasz Majewski
7eee2b500d fix: samsung: common: autoboot.cmd: Correct itbcfg definition
This fix is necessary to avoid booting the default ITB configuration.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2015-06-18 16:11:41 -04:00
Tom Rini
180f87fcc5 mmc_write.c: Make mmc_berase do 32bit safe 64bit math
We want to see if the requested start or total block count are
unaligned.  We discard the whole numbers and only care about the
remainder.  Update the code to use div_u64_rem here and add a comment.

Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
2015-06-18 16:11:41 -04:00
Hannes Petermaier
14ec12fa6f board/BuR/tseries: remove lpj= from environment-variable
since we have now various processor-speeds it isn't useful anymore to
preinitialize kernels-delay loop.

Rather we want the kernel to calibrate it on every boot.
This wastes around 80ms boottime but is compatible to all CPU-speeds.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
2015-06-18 16:11:41 -04:00
Hannes Petermaier
9b63ba3727 board/BuR/common: support timer5 for pwm-backlight
in future we support yet another b&r am335x based board, where Timer 5 is
wired to backlight-driver.

So we introduce a new driver-type '2' to setup timer5 instead timer6.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-06-18 16:11:40 -04:00
Cooper Jr., Franklin
60480f8121 ti: am335x/am437x/omap5 devices: Fix breakage when CONFIG_CMD_NET is not used
Currently there is no default value for NETARGS if CONFIG_CMD_NET=y isn't set.
This results in build errors which was first discovered when trying to run
make env.

By defining a blank NETARGS these errors can be avoided.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Tested-by: Maxin B. John <maxin.john@enea.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-18 16:11:40 -04:00
Jeroen Hofstee
817aa32b93 boards: tam3517-common: enable gpmc prefetch mode
Since the tam3517 base board has a 16bit wide nand connected to
the gpmc, enable the prefetch mode, since that is now supported.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: pekon gupta <pekon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Tapani Utriainen <tapani@technexion.com>

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-18 11:23:45 -04:00
Jeroen Hofstee
cb2fc338f8 mtd: OMAP: Enable GPMC prefetch mode for 16 bit access
commit c316f57 "mtd: OMAP: Enable GPMC prefetch mode" only enabled
prefetch mode for 8 bit nand access, this adds 16 bit as well.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-18 11:23:45 -04:00
Jeroen Hofstee
c07361145f omap_gpmc: move prefetch out of CONFIG_NAND_OMAP_ELM
The prefech mode is a feature of the gpmc, not the ELM. An am3517
does not have an elm, but can do prefeches, so move the code out
of the CONFIG_NAND_OMAP_ELM ifdef.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-18 11:23:45 -04:00
Karsten Merker
24e7412696 MSI_Primo81_defconfig: enable USB OTG port and keyboard support
The MSI Primo 81 is an Allwinner A31s-based tablet on which the
OTG port is the only accessible USB interface.  The existing
defconfig had VGA console on the LCD enabled, but was missing
keyboard support because the prerequisites for that (sunxi MUSB
support and AXP221 GPIO support) had not been available before.
All previously missing dependencies are available now, so this
patch enables keyboard support and its prerequisites in the
defconfig.

Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-06-17 15:31:20 +02:00
Hans de Goede
fc175434f9 sun6i: cpu_reset: Do not return from cpu_reset()
Currently on sun6i after a "reset" the prompt returns and the user can
even type stuff until the watchdog triggers and does the actual reset.

This is somewhat unexpected behavior for the "reset" command, this
commit adds an endless loop to wait for the watchdog to trigger so that
we do not return to the prompt.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-06-17 15:22:47 +02:00