[ Upstream commit 77bbbc0cf84834ed130838f7ac1988567f4d0288 ]
The POWER9 vCPU TLB management code assumes all threads in a core share
a TLB, and that TLBIEL execued by one thread will invalidate TLBs for
all threads. This is not the case for SMT8 capable POWER9 and POWER10
(big core) processors, where the TLB is split between groups of threads.
This results in TLB multi-hits, random data corruption, etc.
Fix this by introducing cpu_first_tlb_thread_sibling etc., to determine
which siblings share TLBs, and use that in the guest TLB flushing code.
[npiggin@gmail.com: add changelog and comment]
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210602040441.3984352-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8b2f37cf632434456182e9002d63cbc4cccc50c ]
When adding a PTE a ptesync is needed to order the update of the PTE
with subsequent accesses otherwise a spurious fault may be raised.
radix__set_pte_at() does not do this for performance gains. For
non-kernel memory this is not an issue as any faults of this kind are
corrected by the page fault handler. For kernel memory these faults
are not handled. The current solution is that there is a ptesync in
flush_cache_vmap() which should be called when mapping from the
vmalloc region.
However, map_kernel_page() does not call flush_cache_vmap(). This is
troublesome in particular for code patching with Strict RWX on radix.
In do_patch_instruction() the page frame that contains the instruction
to be patched is mapped and then immediately patched. With no ordering
or synchronization between setting up the PTE and writing to the page
it is possible for faults.
As the code patching is done using __put_user_asm_goto() the resulting
fault is obscured - but using a normal store instead it can be seen:
BUG: Unable to handle kernel data access on write at 0xc008000008f24a3c
Faulting instruction address: 0xc00000000008bd74
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA PowerNV
Modules linked in: nop_module(PO+) [last unloaded: nop_module]
CPU: 4 PID: 757 Comm: sh Tainted: P O 5.10.0-rc5-01361-ge3c1b78c8440-dirty #43
NIP: c00000000008bd74 LR: c00000000008bd50 CTR: c000000000025810
REGS: c000000016f634a0 TRAP: 0300 Tainted: P O (5.10.0-rc5-01361-ge3c1b78c8440-dirty)
MSR: 9000000000009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 44002884 XER: 00000000
CFAR: c00000000007c68c DAR: c008000008f24a3c DSISR: 42000000 IRQMASK: 1
This results in the kind of issue reported here:
https://lore.kernel.org/linuxppc-dev/15AC5B0E-A221-4B8C-9039-FA96B8EF7C88@lca.pw/
Chris Riedl suggested a reliable way to reproduce the issue:
$ mount -t debugfs none /sys/kernel/debug
$ (while true; do echo function > /sys/kernel/debug/tracing/current_tracer ; echo nop > /sys/kernel/debug/tracing/current_tracer ; done) &
Turning ftrace on and off does a large amount of code patching which
in usually less then 5min will crash giving a trace like:
ftrace-powerpc: (____ptrval____): replaced (4b473b11) != old (60000000)
------------[ ftrace bug ]------------
ftrace failed to modify
[<c000000000bf8e5c>] napi_busy_loop+0xc/0x390
actual: 11:3b:47:4b
Setting ftrace call site to call ftrace function
ftrace record flags: 80000001
(1)
expected tramp: c00000000006c96c
------------[ cut here ]------------
WARNING: CPU: 4 PID: 809 at kernel/trace/ftrace.c:2065 ftrace_bug+0x28c/0x2e8
Modules linked in: nop_module(PO-) [last unloaded: nop_module]
CPU: 4 PID: 809 Comm: sh Tainted: P O 5.10.0-rc5-01360-gf878ccaf250a #1
NIP: c00000000024f334 LR: c00000000024f330 CTR: c0000000001a5af0
REGS: c000000004c8b760 TRAP: 0700 Tainted: P O (5.10.0-rc5-01360-gf878ccaf250a)
MSR: 900000000282b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 28008848 XER: 20040000
CFAR: c0000000001a9c98 IRQMASK: 0
GPR00: c00000000024f330 c000000004c8b9f0 c000000002770600 0000000000000022
GPR04: 00000000ffff7fff c000000004c8b6d0 0000000000000027 c0000007fe9bcdd8
GPR08: 0000000000000023 ffffffffffffffd8 0000000000000027 c000000002613118
GPR12: 0000000000008000 c0000007fffdca00 0000000000000000 0000000000000000
GPR16: 0000000023ec37c5 0000000000000000 0000000000000000 0000000000000008
GPR20: c000000004c8bc90 c0000000027a2d20 c000000004c8bcd0 c000000002612fe8
GPR24: 0000000000000038 0000000000000030 0000000000000028 0000000000000020
GPR28: c000000000ff1b68 c000000000bf8e5c c00000000312f700 c000000000fbb9b0
NIP ftrace_bug+0x28c/0x2e8
LR ftrace_bug+0x288/0x2e8
Call Trace:
ftrace_bug+0x288/0x2e8 (unreliable)
ftrace_modify_all_code+0x168/0x210
arch_ftrace_update_code+0x18/0x30
ftrace_run_update_code+0x44/0xc0
ftrace_startup+0xf8/0x1c0
register_ftrace_function+0x4c/0xc0
function_trace_init+0x80/0xb0
tracing_set_tracer+0x2a4/0x4f0
tracing_set_trace_write+0xd4/0x130
vfs_write+0xf0/0x330
ksys_write+0x84/0x140
system_call_exception+0x14c/0x230
system_call_common+0xf0/0x27c
To fix this when updating kernel memory PTEs using ptesync.
Fixes: f1cb8f9beb ("powerpc/64s/radix: avoid ptesync after set_pte and ptep_set_access_flags")
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Tidy up change log slightly]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210208032957.1232102-1-jniethe5@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7de21e679e6a789f3729e8402bc440b623a28eae upstream.
A few archs like powerpc have different errno.h values for macros
EDEADLOCK and EDEADLK. In code including both libc and linux versions of
errno.h, this can result in multiple definitions of EDEADLOCK in the
include chain. Definitions to the same value (e.g. seen with mips) do
not raise warnings, but on powerpc there are redefinitions changing the
value, which raise warnings and errors (if using "-Werror").
Guard against these redefinitions to avoid build errors like the following,
first seen cross-compiling libbpf v5.8.9 for powerpc using GCC 8.4.0 with
musl 1.1.24:
In file included from ../../arch/powerpc/include/uapi/asm/errno.h:5,
from ../../include/linux/err.h:8,
from libbpf.c:29:
../../include/uapi/asm-generic/errno.h:40: error: "EDEADLOCK" redefined [-Werror]
#define EDEADLOCK EDEADLK
In file included from toolchain-powerpc_8540_gcc-8.4.0_musl/include/errno.h:10,
from libbpf.c:26:
toolchain-powerpc_8540_gcc-8.4.0_musl/include/bits/errno.h:58: note: this is the location of the previous definition
#define EDEADLOCK 58
cc1: all warnings being treated as errors
Cc: Stable <stable@vger.kernel.org>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Tony Ambardar <Tony.Ambardar@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200917135437.1238787-1-Tony.Ambardar@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eed5fae00593ab9d261a0c1ffc1bdb786a87a55a ]
The code relies on constant folding of cpu_has_feature() based
on possible and always true values as defined per
CPU_FTRS_ALWAYS and CPU_FTRS_POSSIBLE.
Build failure is encountered with for instance
book3e_all_defconfig on kisskb in the AMDGPU driver which uses
cpu_has_feature(CPU_FTR_VSX_COMP) to decide whether calling
kernel_enable_vsx() or not.
The failure is due to cpu_has_feature() not being inlined with
that configuration with gcc 4.9.
In the same way as commit acdad8fb4a15 ("powerpc: Force inlining of
mmu_has_feature to fix build failure"), for inlining of
cpu_has_feature().
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b231dfa040ce4cc37f702f5c3a595fdeabfe0462.1615378209.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eead089311f4d935ab5d1d8fbb0c42ad44699ada ]
lkp reported a build error in fsp2.o:
CC arch/powerpc/platforms/44x/fsp2.o
{standard input}:577: Error: unsupported relocation against base
Which comes from:
pr_err("GESR0: 0x%08x\n", mfdcr(base + PLB4OPB_GESR0));
Where our mfdcr() macro is stringifying "base + PLB4OPB_GESR0", and
passing that to the assembler, which obviously doesn't work.
The mfdcr() macro already checks that the argument is constant using
__builtin_constant_p(), and if not calls the out-of-line version of
mfdcr(). But in this case GCC is smart enough to notice that "base +
PLB4OPB_GESR0" will be constant, even though it's not something we can
immediately stringify into a register number.
Segher pointed out that passing the register number to the inline asm
as a constant would be better, and in fact it fixes the build error,
presumably because it gives GCC a chance to resolve the value.
While we're at it, change mtdcr() similarly.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210218123058.748882-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cea15316ceee2d4a51dfdecd79e08a438135416c upstream.
'lis r2,N' is 'addis r2,0,N' and the instruction encoding in the macro
LIS_R2 is incorrect (it currently maps to 'addis r0,r2,N'). Fix the
same.
Fixes: c71b7eff42 ("powerpc: Add ABIv2 support to ppc_function_entry")
Cc: stable@vger.kernel.org # v3.16+
Reported-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210304020411.16796-1-naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3de1e291fa58a1ab0f471a4b458eff2514e4b5f ]
In commit bf13718bc57a ("powerpc: show registers when unwinding
interrupt frames") we changed our stack dumping logic to show the full
registers whenever we find an interrupt frame on the stack.
However we didn't notice that on 64-bit this doesn't show the final
frame, ie. the interrupt that brought us in from userspace, whereas on
32-bit it does.
That is due to confusion about the size of that last frame. The code
in show_stack() calls validate_sp(), passing it STACK_INT_FRAME_SIZE
to check the sp is at least that far below the top of the stack.
However on 64-bit that size is too large for the final frame, because
it includes the red zone, but we don't allocate a red zone for the
first frame.
So add a new define that encodes the correct size for 32-bit and
64-bit, and use it in show_stack().
This results in the full trace being shown on 64-bit, eg:
sysrq: Trigger a crash
Kernel panic - not syncing: sysrq triggered crash
CPU: 0 PID: 83 Comm: sh Not tainted 5.11.0-rc2-gcc-8.2.0-00188-g571abcb96b10-dirty #649
Call Trace:
[c00000000a1c3ac0] [c000000000897b70] dump_stack+0xc4/0x114 (unreliable)
[c00000000a1c3b00] [c00000000014334c] panic+0x178/0x41c
[c00000000a1c3ba0] [c00000000094e600] sysrq_handle_crash+0x40/0x50
[c00000000a1c3c00] [c00000000094ef98] __handle_sysrq+0xd8/0x210
[c00000000a1c3ca0] [c00000000094f820] write_sysrq_trigger+0x100/0x188
[c00000000a1c3ce0] [c0000000005559dc] proc_reg_write+0x10c/0x1b0
[c00000000a1c3d10] [c000000000479950] vfs_write+0xf0/0x360
[c00000000a1c3d60] [c000000000479d9c] ksys_write+0x7c/0x140
[c00000000a1c3db0] [c00000000002bf5c] system_call_exception+0x19c/0x2c0
[c00000000a1c3e10] [c00000000000d35c] system_call_common+0xec/0x278
--- interrupt: c00 at 0x7fff9fbab428
NIP: 00007fff9fbab428 LR: 000000001000b724 CTR: 0000000000000000
REGS: c00000000a1c3e80 TRAP: 0c00 Not tainted (5.11.0-rc2-gcc-8.2.0-00188-g571abcb96b10-dirty)
MSR: 900000000280f033 <SF,HV,VEC,VSX,EE,PR,FP,ME,IR,DR,RI,LE> CR: 22002884 XER: 00000000
IRQMASK: 0
GPR00: 0000000000000004 00007fffc3cb8960 00007fff9fc59900 0000000000000001
GPR04: 000000002a4b32d0 0000000000000002 0000000000000063 0000000000000063
GPR08: 000000002a4b32d0 0000000000000000 0000000000000000 0000000000000000
GPR12: 0000000000000000 00007fff9fcca9a0 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 00000000100b8fd0
GPR20: 000000002a4b3485 00000000100b8f90 0000000000000000 0000000000000000
GPR24: 000000002a4b0440 00000000100e77b8 0000000000000020 000000002a4b32d0
GPR28: 0000000000000001 0000000000000002 000000002a4b32d0 0000000000000001
NIP [00007fff9fbab428] 0x7fff9fbab428
LR [000000001000b724] 0x1000b724
--- interrupt: c00
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210209141627.2898485-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5537fcb319d016ce387f818dd774179bc03217f5 ]
On many powerpc platforms the discovery and initalisation of
pci_controllers (PHBs) happens inside of setup_arch(). This is very early
in boot (pre-initcalls) and means that we're initialising the PHB long
before many basic kernel services (slab allocator, debugfs, a real ioremap)
are available.
On PowerNV this causes an additional problem since we map the PHB registers
with ioremap(). As of commit d538aadc2718 ("powerpc/ioremap: warn on early
use of ioremap()") a warning is printed because we're using the "incorrect"
API to setup and MMIO mapping in searly boot. The kernel does provide
early_ioremap(), but that is not intended to create long-lived MMIO
mappings and a seperate warning is printed by generic code if
early_ioremap() mappings are "leaked."
This is all fixable with dumb hacks like using early_ioremap() to setup
the initial mapping then replacing it with a real ioremap later on in
boot, but it does raise the question: Why the hell are we setting up the
PHB's this early in boot?
The old and wise claim it's due to "hysterical rasins." Aside from amused
grapes there doesn't appear to be any real reason to maintain the current
behaviour. Already most of the newer embedded platforms perform PHB
discovery in an arch_initcall and between the end of setup_arch() and the
start of initcalls none of the generic kernel code does anything PCI
related. On powerpc scanning PHBs occurs in a subsys_initcall so it should
be possible to move the PHB discovery to a core, postcore or arch initcall.
This patch adds the ppc_md.discover_phbs hook and a core_initcall stub that
calls it. The core_initcalls are the earliest to be called so this will
any possibly issues with dependency between initcalls. This isn't just an
academic issue either since on pseries and PowerNV EEH init occurs in an
arch_initcall and depends on the pci_controllers being available, similarly
the creation of pci_dns occurs at core_initcall_sync (i.e. between core and
postcore initcalls). These problems need to be addressed seperately.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[mpe: Make discover_phbs() static]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201103043523.916109-1-oohall@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=fZ3T
-----END PGP SIGNATURE-----
Merge tag 'v5.4.73' into 5.4-2.3.x-imx
This is the 5.4.73 stable release
Conflicts:
- arch/arm/boot/dts/imx6sl.dtsi:
Commit [a1767c9019] in NXP tree is now covered with commit [5c4c2f437c]
from upstream.
- drivers/gpu/drm/mxsfb/mxsfb_drv.c:
Resolve merge hunk for patch [ed8b90d303] from upstream
- drivers/media/i2c/ov5640.c:
Patch [aa4bb8b883] in NXP tree is now covered by patches [79ec0578c7]
and [b2f8546056] from upstream. Changes from NXP patch [99aa4c8c18] are
covered in upstream version as well.
- drivers/net/ethernet/freescale/fec_main.c:
Fix merge fuzz for patch [9e70485b40] from upstream.
- drivers/usb/cdns3/gadget.c:
Keep NXP version of the file, upstream version is not compatible.
- drivers/usb/dwc3/core.c:
- drivers/usb/dwc3/core.h:
Fix merge fuzz of patch [08045050c6] together wth NXP patch [b30e41dc1e]
- sound/soc/fsl/fsl_sai.c:
- sound/soc/fsl/fsl_sai.h:
Commit [2ea70e51eb72a] in NXP tree is now covered with commit [1ad7f52fe6]
from upstream.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
[ Upstream commit 1891ef21d92c4801ea082ee8ed478e304ddc6749 ]
fls() and fls64() are using __builtin_ctz() and _builtin_ctzll().
On powerpc, those builtins trivially use ctlzw and ctlzd power
instructions.
Allthough those instructions provide the expected result with
input argument 0, __builtin_ctz() and __builtin_ctzll() are
documented as undefined for value 0.
The easiest fix would be to use fls() and fls64() functions
defined in include/asm-generic/bitops/builtin-fls.h and
include/asm-generic/bitops/fls64.h, but GCC output is not optimal:
00000388 <testfls>:
388: 2c 03 00 00 cmpwi r3,0
38c: 41 82 00 10 beq 39c <testfls+0x14>
390: 7c 63 00 34 cntlzw r3,r3
394: 20 63 00 20 subfic r3,r3,32
398: 4e 80 00 20 blr
39c: 38 60 00 00 li r3,0
3a0: 4e 80 00 20 blr
000003b0 <testfls64>:
3b0: 2c 03 00 00 cmpwi r3,0
3b4: 40 82 00 1c bne 3d0 <testfls64+0x20>
3b8: 2f 84 00 00 cmpwi cr7,r4,0
3bc: 38 60 00 00 li r3,0
3c0: 4d 9e 00 20 beqlr cr7
3c4: 7c 83 00 34 cntlzw r3,r4
3c8: 20 63 00 20 subfic r3,r3,32
3cc: 4e 80 00 20 blr
3d0: 7c 63 00 34 cntlzw r3,r3
3d4: 20 63 00 40 subfic r3,r3,64
3d8: 4e 80 00 20 blr
When the input of fls(x) is a constant, just check x for nullity and
return either 0 or __builtin_clz(x). Otherwise, use cntlzw instruction
directly.
For fls64() on PPC64, do the same but with __builtin_clzll() and
cntlzd instruction. On PPC32, lets take the generic fls64() which
will use our fls(). The result is as expected:
00000388 <testfls>:
388: 7c 63 00 34 cntlzw r3,r3
38c: 20 63 00 20 subfic r3,r3,32
390: 4e 80 00 20 blr
000003a0 <testfls64>:
3a0: 2c 03 00 00 cmpwi r3,0
3a4: 40 82 00 10 bne 3b4 <testfls64+0x14>
3a8: 7c 83 00 34 cntlzw r3,r4
3ac: 20 63 00 20 subfic r3,r3,32
3b0: 4e 80 00 20 blr
3b4: 7c 63 00 34 cntlzw r3,r3
3b8: 20 63 00 40 subfic r3,r3,64
3bc: 4e 80 00 20 blr
Fixes: 2fcff790dc ("powerpc: Use builtin functions for fls()/__fls()/fls64()")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/348c2d3f19ffcff8abe50d52513f989c4581d000.1603375524.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1e78f723d6a52966bfe3804209dbf404fdc9d3bb upstream.
When SMC1 is relocated and early debug is selected, the
board hangs is ppc_md.setup_arch(). This is because ones
the microcode has been loaded and SMC1 relocated, early
debug writes in the weed.
To allow smooth continuation, the SMC1 parameter RAM set up
by the bootloader have to be copied into the new location.
Fixes: 43db76f418 ("powerpc/8xx: Add microcode patch to move SMC parameter RAM.")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b2f71f39eca543f1e4ec06596f09a8b12235c701.1607076683.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d85be8a49e733dcd23674aa6202870d54bf5600d upstream.
The placeholder for instruction selection should use the second
argument's operand, which is %1, not %0. This could generate incorrect
assembly code if the memory addressing of operand %0 is a different
form from that of operand %1.
Also remove the %Un placeholder because having %Un placeholders
for two operands which are based on the same local var (ptep) doesn't
make much sense. By the way, it doesn't change the current behaviour
because "<>" constraint is missing for the associated "=m".
[chleroy: revised commit log iaw segher's comments and removed %U0]
Fixes: 9bf2b5cdc5 ("powerpc: Fixes for CONFIG_PTE_64BIT for SMP support")
Cc: <stable@vger.kernel.org> # v2.6.28+
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/96354bd77977a6a933fe9020da57629007fdb920.1603358942.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78665179e569c7e1fe102fb6c21d0f5b6951f084 ]
On 8xx, we get the following features:
[ 0.000000] cpu_features = 0x0000000000000100
[ 0.000000] possible = 0x0000000000000120
[ 0.000000] always = 0x0000000000000000
This is not correct. As CONFIG_PPC_8xx is mutually exclusive with all
other configurations, the three lines should be equal.
The problem is due to CPU_FTRS_GENERIC_32 which is taken when
CONFIG_BOOK3S_32 is NOT selected. This CPU_FTRS_GENERIC_32 is
pointless because there is no generic configuration supporting
all 32 bits but book3s/32.
Remove this pointless generic features definition to unbreak the
calculation of 'possible' features and 'always' features.
Fixes: 76bc080ef5 ("[POWERPC] Make default cputable entries reflect selected CPU family")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/76a85f30bf981d1aeaae00df99321235494da254.1604426550.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6b79dd53082db11070b4368d85dd6699ff0b063 ]
Using DECLARE_STATIC_KEY_FALSE needs linux/jump_table.h.
Otherwise the build fails with eg:
arch/powerpc/include/asm/book3s/64/kup-radix.h:66:1: warning: data definition has no type or storage class
66 | DECLARE_STATIC_KEY_FALSE(uaccess_flush_key);
Fixes: 9a32a7e78bd0 ("powerpc/64s: flush L1D after user accesses")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[mpe: Massage change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201123184016.693fe464@canb.auug.org.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cef397038167ac15d085914493d6c86385773709 ]
Stefan Agner reported a bug when using zsram on 32-bit Arm machines
with RAM above the 4GB address boundary:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = a27bd01c
[00000000] *pgd=236a0003, *pmd=1ffa64003
Internal error: Oops: 207 [#1] SMP ARM
Modules linked in: mdio_bcm_unimac(+) brcmfmac cfg80211 brcmutil raspberrypi_hwmon hci_uart crc32_arm_ce bcm2711_thermal phy_generic genet
CPU: 0 PID: 123 Comm: mkfs.ext4 Not tainted 5.9.6 #1
Hardware name: BCM2711
PC is at zs_map_object+0x94/0x338
LR is at zram_bvec_rw.constprop.0+0x330/0xa64
pc : [<c0602b38>] lr : [<c0bda6a0>] psr: 60000013
sp : e376bbe0 ip : 00000000 fp : c1e2921c
r10: 00000002 r9 : c1dda730 r8 : 00000000
r7 : e8ff7a00 r6 : 00000000 r5 : 02f9ffa0 r4 : e3710000
r3 : 000fdffe r2 : c1e0ce80 r1 : ebf979a0 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 30c5383d Table: 235c2a80 DAC: fffffffd
Process mkfs.ext4 (pid: 123, stack limit = 0x495a22e6)
Stack: (0xe376bbe0 to 0xe376c000)
As it turns out, zsram needs to know the maximum memory size, which
is defined in MAX_PHYSMEM_BITS when CONFIG_SPARSEMEM is set, or in
MAX_POSSIBLE_PHYSMEM_BITS on the x86 architecture.
The same problem will be hit on all 32-bit architectures that have a
physical address space larger than 4GB and happen to not enable sparsemem
and include asm/sparsemem.h from asm/pgtable.h.
After the initial discussion, I suggested just always defining
MAX_POSSIBLE_PHYSMEM_BITS whenever CONFIG_PHYS_ADDR_T_64BIT is
set, or provoking a build error otherwise. This addresses all
configurations that can currently have this runtime bug, but
leaves all other configurations unchanged.
I looked up the possible number of bits in source code and
datasheets, here is what I found:
- on ARC, CONFIG_ARC_HAS_PAE40 controls whether 32 or 40 bits are used
- on ARM, CONFIG_LPAE enables 40 bit addressing, without it we never
support more than 32 bits, even though supersections in theory allow
up to 40 bits as well.
- on MIPS, some MIPS32r1 or later chips support 36 bits, and MIPS32r5
XPA supports up to 60 bits in theory, but 40 bits are more than
anyone will ever ship
- On PowerPC, there are three different implementations of 36 bit
addressing, but 32-bit is used without CONFIG_PTE_64BIT
- On RISC-V, the normal page table format can support 34 bit
addressing. There is no highmem support on RISC-V, so anything
above 2GB is unused, but it might be useful to eventually support
CONFIG_ZRAM for high pages.
Fixes: 61989a80fb ("staging: zsmalloc: zsmalloc memory allocation library")
Fixes: 02390b87a9 ("mm/zsmalloc: Prepare to variable MAX_PHYSMEM_BITS")
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Link: https://lore.kernel.org/linux-mm/bdfa44bf1c570b05d6c70898e2bbb0acf234ecdf.1604762181.git.stefan@agner.ch/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 178d52c6e89c38d0553b0ac8b99927b11eb995b0 upstream.
In kup.h we currently include kup-radix.h for all 64-bit builds, which
includes Book3S and Book3E. The latter doesn't make sense, Book3E
never uses the Radix MMU.
This has worked up until now, but almost by accident, and the recent
uaccess flush changes introduced a build breakage on Book3E because of
the bad structure of the code.
So disentangle things so that we only use kup-radix.h for Book3S. This
requires some more stubs in kup.h.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a32a7e78bd0cd9a9b6332cbdc345ee5ffd0c5de upstream.
IBM Power9 processors can speculatively operate on data in the L1 cache
before it has been completely validated, via a way-prediction mechanism. It
is not possible for an attacker to determine the contents of impermissible
memory using this method, since these systems implement a combination of
hardware and software security measures to prevent scenarios where
protected data could be leaked.
However these measures don't address the scenario where an attacker induces
the operating system to speculatively execute instructions using data that
the attacker controls. This can be used for example to speculatively bypass
"kernel user access prevention" techniques, as discovered by Anthony
Steinhauser of Google's Safeside Project. This is not an attack by itself,
but there is a possibility it could be used in conjunction with
side-channels or other weaknesses in the privileged code to construct an
attack.
This issue can be mitigated by flushing the L1 cache between privilege
boundaries of concern. This patch flushes the L1 cache after user accesses.
This is part of the fix for CVE-2020-4788.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f79643787e0a0762d2409b7b8334e83f22d85695 upstream.
[backporting note: we need to mark some exception handlers as out-of-line
because the flushing makes them take too much space -- dja]
IBM Power9 processors can speculatively operate on data in the L1 cache
before it has been completely validated, via a way-prediction mechanism. It
is not possible for an attacker to determine the contents of impermissible
memory using this method, since these systems implement a combination of
hardware and software security measures to prevent scenarios where
protected data could be leaked.
However these measures don't address the scenario where an attacker induces
the operating system to speculatively execute instructions using data that
the attacker controls. This can be used for example to speculatively bypass
"kernel user access prevention" techniques, as discovered by Anthony
Steinhauser of Google's Safeside Project. This is not an attack by itself,
but there is a possibility it could be used in conjunction with
side-channels or other weaknesses in the privileged code to construct an
attack.
This issue can be mitigated by flushing the L1 cache between privilege
boundaries of concern. This patch flushes the L1 cache on kernel entry.
This is part of the fix for CVE-2020-4788.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec72024e35dddb88a81e40071c87ceb18b5ee835 upstream.
Similar to commit 89c140bbaeee ("pseries: Fix 64 bit logical memory block panic")
make sure different variables tracking lmb_size are updated to be 64 bit.
This was found by code audit.
Cc: stable@vger.kernel.org
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Acked-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201007114836.282468-2-aneesh.kumar@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 66acd46080bd9e5ad2be4b0eb1d498d5145d058e ]
powerpc uses IPIs in some situations to switch a kernel thread away
from a lazy tlb mm, which is subject to the TLB flushing race
described in the changelog introducing ARCH_WANT_IRQS_OFF_ACTIVATE_MM.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200914045219.3736466-3-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a665eec0a22e11cdde708c1c256a465ebe768047 ]
Commit 0cef77c779 ("powerpc/64s/radix: flush remote CPUs out of
single-threaded mm_cpumask") added a mechanism to trim the mm_cpumask of
a process under certain conditions. One of the assumptions is that
mm_users would not be incremented via a reference outside the process
context with mmget_not_zero() then go on to kthread_use_mm() via that
reference.
That invariant was broken by io_uring code (see previous sparc64 fix),
but I'll point Fixes: to the original powerpc commit because we are
changing that assumption going forward, so this will make backports
match up.
Fix this by no longer relying on that assumption, but by having each CPU
check the mm is not being used, and clearing their own bit from the mask
only if it hasn't been switched-to by the time the IPI is processed.
This relies on commit 38cf307c1f20 ("mm: fix kthread_use_mm() vs TLB
invalidate") and ARCH_WANT_IRQS_OFF_ACTIVATE_MM to disable irqs over mm
switch sequences.
Fixes: 0cef77c779 ("powerpc/64s/radix: flush remote CPUs out of single-threaded mm_cpumask")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au>
Depends-on: 38cf307c1f20 ("mm: fix kthread_use_mm() vs TLB invalidate")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200914045219.3736466-5-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66943005cc41f48e4d05614e8f76c0ca1812f0fd ]
According to the MPC750 Users Manual, the SITV value in Thermal
Management Register 3 is 13 bits long. The present code calculates the
SITV value as 60 * 500 cycles. This would overflow to give 10 us on
a 500 MHz CPU rather than the intended 60 us. (But according to the
Microprocessor Datasheet, there is also a factor of 266 that has to be
applied to this value on certain parts i.e. speed sort above 266 MHz.)
Always use the maximum cycle count, as recommended by the Datasheet.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/896f542e5f0f1d6cf8218524c2b67d79f3d69b3c.1599260540.git.fthain@telegraphics.com.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7746406baa3bc9e23fdd7b7da2f04d86e25ab837 ]
With commit: 0034d395f8 ("powerpc/mm/hash64: Map all the kernel
regions in the same 0xc range"), we now split the 64TB address range
into 4 contexts each of 16TB. That implies we can do only 16TB linear
mapping.
On some systems, eg. Power9, memory attached to nodes > 0 will appear
above 16TB in the linear mapping. This resulted in kernel crash when
we boot such systems in hash translation mode with 4K PAGE_SIZE.
This patch updates the kernel mapping such that we now start supporting upto
61TB of memory with 4K. The kernel mapping now looks like below 4K PAGE_SIZE
and hash translation.
vmalloc start = 0xc0003d0000000000
IO start = 0xc0003e0000000000
vmemmap start = 0xc0003f0000000000
Our MAX_PHYSMEM_BITS for 4K is still 64TB even though we can only map 61TB.
We prevent bolt mapping anything outside 61TB range by checking against
H_VMALLOC_START.
Fixes: 0034d395f8 ("powerpc/mm/hash64: Map all the kernel regions in the same 0xc range")
Reported-by: Cameron Berkenpas <cam@neo-zeon.de>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200608070904.387440-3-aneesh.kumar@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5e179aa3a39c818db8fbc2dce8d2cd24adaf657 ]
At memory hot-remove time we can retrieve an LMB's nid from its
corresponding memory_block. There is no need to store the nid
in multiple locations.
Note that lmb_to_memblock() uses find_memory_block() to get the
corresponding memory_block. As find_memory_block() runs in sub-linear
time this approach is negligibly slower than what we do at present.
In exchange for this lookup at hot-remove time we no longer need to
call memory_add_physaddr_to_nid() during drmem_init() for each LMB.
On powerpc, memory_add_physaddr_to_nid() is a linear search, so this
spares us an O(n^2) initialization during boot.
On systems with many LMBs that initialization overhead is palpable and
disruptive. For example, on a box with 249854 LMBs we're seeing
drmem_init() take upwards of 30 seconds to complete:
[ 53.721639] drmem: initializing drmem v2
[ 80.604346] watchdog: BUG: soft lockup - CPU#65 stuck for 23s! [swapper/0:1]
[ 80.604377] Modules linked in:
[ 80.604389] CPU: 65 PID: 1 Comm: swapper/0 Not tainted 5.6.0-rc2+ #4
[ 80.604397] NIP: c0000000000a4980 LR: c0000000000a4940 CTR: 0000000000000000
[ 80.604407] REGS: c0002dbff8493830 TRAP: 0901 Not tainted (5.6.0-rc2+)
[ 80.604412] MSR: 8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 44000248 XER: 0000000d
[ 80.604431] CFAR: c0000000000a4a38 IRQMASK: 0
[ 80.604431] GPR00: c0000000000a4940 c0002dbff8493ac0 c000000001904400 c0003cfffffede30
[ 80.604431] GPR04: 0000000000000000 c000000000f4095a 000000000000002f 0000000010000000
[ 80.604431] GPR08: c0000bf7ecdb7fb8 c0000bf7ecc2d3c8 0000000000000008 c00c0002fdfb2001
[ 80.604431] GPR12: 0000000000000000 c00000001e8ec200
[ 80.604477] NIP [c0000000000a4980] hot_add_scn_to_nid+0xa0/0x3e0
[ 80.604486] LR [c0000000000a4940] hot_add_scn_to_nid+0x60/0x3e0
[ 80.604492] Call Trace:
[ 80.604498] [c0002dbff8493ac0] [c0000000000a4940] hot_add_scn_to_nid+0x60/0x3e0 (unreliable)
[ 80.604509] [c0002dbff8493b20] [c000000000087c10] memory_add_physaddr_to_nid+0x20/0x60
[ 80.604521] [c0002dbff8493b40] [c0000000010d4880] drmem_init+0x25c/0x2f0
[ 80.604530] [c0002dbff8493c10] [c000000000010154] do_one_initcall+0x64/0x2c0
[ 80.604540] [c0002dbff8493ce0] [c0000000010c4aa0] kernel_init_freeable+0x2d8/0x3a0
[ 80.604550] [c0002dbff8493db0] [c000000000010824] kernel_init+0x2c/0x148
[ 80.604560] [c0002dbff8493e20] [c00000000000b648] ret_from_kernel_thread+0x5c/0x74
[ 80.604567] Instruction dump:
[ 80.604574] 392918e8 e9490000 e90a000a e92a0000 80ea000c 1d080018 3908ffe8 7d094214
[ 80.604586] 7fa94040 419d00dc e9490010 714a0088 <2faa0008> 409e00ac e9490000 7fbe5040
[ 89.047390] drmem: 249854 LMB(s)
With a patched kernel on the same machine we're no longer seeing the
soft lockup. drmem_init() now completes in negligible time, even when
the LMB count is large.
Fixes: b2d3b5ee66 ("powerpc/pseries: Track LMB nid instead of using device tree")
Signed-off-by: Scott Cheloha <cheloha@linux.ibm.com>
Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200811015115.63677-1-cheloha@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d6792ffe140240ae54c881cc4183f9acc24b4df ]
The drmem lmb list can have hundreds of thousands of entries, and
unfortunately lookups take the form of linear searches. As long as
this is the case, traversals have the potential to monopolize the CPU
and provoke lockup reports, workqueue stalls, and the like unless
they explicitly yield.
Rather than placing cond_resched() calls within various
for_each_drmem_lmb() loop blocks in the code, put it in the iteration
expression of the loop macro itself so users can't omit it.
Introduce a drmem_lmb_next() iteration helper function which calls
cond_resched() at a regular interval during array traversal. Each
iteration of the loop in DLPAR code paths can involve around ten RTAS
calls which can each take up to 250us, so this ensures the check is
performed at worst every few milliseconds.
Fixes: 6c6ea53725 ("powerpc/mm: Separate ibm, dynamic-memory data from DT format")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200813151131.2070161-1-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
* tag 'v5.4.70': (3051 commits)
Linux 5.4.70
netfilter: ctnetlink: add a range check for l3/l4 protonum
ep_create_wakeup_source(): dentry name can change under you...
...
Conflicts:
arch/arm/mach-imx/pm-imx6.c
arch/arm64/boot/dts/freescale/imx8mm-evk.dts
arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
drivers/crypto/caam/caamalg.c
drivers/gpu/drm/imx/dw_hdmi-imx.c
drivers/gpu/drm/imx/imx-ldb.c
drivers/gpu/drm/imx/ipuv3/ipuv3-crtc.c
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c
drivers/net/ethernet/freescale/enetc/enetc.c
drivers/net/ethernet/freescale/enetc/enetc_pf.c
drivers/thermal/imx_thermal.c
drivers/usb/cdns3/ep0.c
drivers/xen/swiotlb-xen.c
sound/soc/fsl/fsl_esai.c
sound/soc/fsl/fsl_sai.c
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
[ Upstream commit 1dff3064c764b5a51c367b949b341d2e38972bec ]
On P9 DD2.2 due to a CPU defect some TM instructions need to be emulated by
KVM. This is handled at first by the hardware raising a softpatch interrupt
when certain TM instructions that need KVM assistance are executed in the
guest. Althought some TM instructions per Power ISA are invalid forms they
can raise a softpatch interrupt too. For instance, 'tresume.' instruction
as defined in the ISA must have bit 31 set (1), but an instruction that
matches 'tresume.' PO and XO opcode fields but has bit 31 not set (0), like
0x7cfe9ddc, also raises a softpatch interrupt. Similarly for 'treclaim.'
and 'trechkpt.' instructions with bit 31 = 0, i.e. 0x7c00075c and
0x7c0007dc, respectively. Hence, if a code like the following is executed
in the guest it will raise a softpatch interrupt just like a 'tresume.'
when the TM facility is enabled ('tabort. 0' in the example is used only
to enable the TM facility):
int main() { asm("tabort. 0; .long 0x7cfe9ddc;"); }
Currently in such a case KVM throws a complete trace like:
[345523.705984] WARNING: CPU: 24 PID: 64413 at arch/powerpc/kvm/book3s_hv_tm.c:211 kvmhv_p9_tm_emulation+0x68/0x620 [kvm_hv]
[345523.705985] Modules linked in: kvm_hv(E) xt_conntrack ipt_REJECT nf_reject_ipv4 xt_tcpudp ip6table_mangle ip6table_nat
iptable_mangle iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ebtable_filter ebtables ip6table_filter
ip6_tables iptable_filter bridge stp llc sch_fq_codel ipmi_powernv at24 vmx_crypto ipmi_devintf ipmi_msghandler
ibmpowernv uio_pdrv_genirq kvm opal_prd uio leds_powernv ib_iser rdma_cm iw_cm ib_cm ib_core iscsi_tcp libiscsi_tcp
libiscsi scsi_transport_iscsi ip_tables x_tables autofs4 btrfs blake2b_generic zstd_compress raid10 raid456
async_raid6_recov async_memcpy async_pq async_xor async_tx libcrc32c xor raid6_pq raid1 raid0 multipath linear tg3
crct10dif_vpmsum crc32c_vpmsum ipr [last unloaded: kvm_hv]
[345523.706030] CPU: 24 PID: 64413 Comm: CPU 0/KVM Tainted: G W E 5.5.0+ #1
[345523.706031] NIP: c0080000072cb9c0 LR: c0080000072b5e80 CTR: c0080000085c7850
[345523.706034] REGS: c000000399467680 TRAP: 0700 Tainted: G W E (5.5.0+)
[345523.706034] MSR: 900000010282b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]> CR: 24022428 XER: 00000000
[345523.706042] CFAR: c0080000072b5e7c IRQMASK: 0
GPR00: c0080000072b5e80 c000000399467910 c0080000072db500 c000000375ccc720
GPR04: c000000375ccc720 00000003fbec0000 0000a10395dda5a6 0000000000000000
GPR08: 000000007cfe9ddc 7cfe9ddc000005dc 7cfe9ddc7c0005dc c0080000072cd530
GPR12: c0080000085c7850 c0000003fffeb800 0000000000000001 00007dfb737f0000
GPR16: c0002001edcca558 0000000000000000 0000000000000000 0000000000000001
GPR20: c000000001b21258 c0002001edcca558 0000000000000018 0000000000000000
GPR24: 0000000001000000 ffffffffffffffff 0000000000000001 0000000000001500
GPR28: c0002001edcc4278 c00000037dd80000 800000050280f033 c000000375ccc720
[345523.706062] NIP [c0080000072cb9c0] kvmhv_p9_tm_emulation+0x68/0x620 [kvm_hv]
[345523.706065] LR [c0080000072b5e80] kvmppc_handle_exit_hv.isra.53+0x3e8/0x798 [kvm_hv]
[345523.706066] Call Trace:
[345523.706069] [c000000399467910] [c000000399467940] 0xc000000399467940 (unreliable)
[345523.706071] [c000000399467950] [c000000399467980] 0xc000000399467980
[345523.706075] [c0000003994679f0] [c0080000072bd1c4] kvmhv_run_single_vcpu+0xa1c/0xb80 [kvm_hv]
[345523.706079] [c000000399467ac0] [c0080000072bd8e0] kvmppc_vcpu_run_hv+0x5b8/0xb00 [kvm_hv]
[345523.706087] [c000000399467b90] [c0080000085c93cc] kvmppc_vcpu_run+0x34/0x48 [kvm]
[345523.706095] [c000000399467bb0] [c0080000085c582c] kvm_arch_vcpu_ioctl_run+0x244/0x420 [kvm]
[345523.706101] [c000000399467c40] [c0080000085b7498] kvm_vcpu_ioctl+0x3d0/0x7b0 [kvm]
[345523.706105] [c000000399467db0] [c0000000004adf9c] ksys_ioctl+0x13c/0x170
[345523.706107] [c000000399467e00] [c0000000004adff8] sys_ioctl+0x28/0x80
[345523.706111] [c000000399467e20] [c00000000000b278] system_call+0x5c/0x68
[345523.706112] Instruction dump:
[345523.706114] 419e0390 7f8a4840 409d0048 6d497c00 2f89075d 419e021c 6d497c00 2f8907dd
[345523.706119] 419e01c0 6d497c00 2f8905dd 419e00a4 <0fe00000> 38210040 38600000 ebc1fff0
and then treats the executed instruction as a 'nop'.
However the POWER9 User's Manual, in section "4.6.10 Book II Invalid
Forms", informs that for TM instructions bit 31 is in fact ignored, thus
for the TM-related invalid forms ignoring bit 31 and handling them like the
valid forms is an acceptable way to handle them. POWER8 behaves the same
way too.
This commit changes the handling of the cases here described by treating
the TM-related invalid forms that can generate a softpatch interrupt
just like their valid forms (w/ bit 31 = 1) instead of as a 'nop' and by
gently reporting any other unrecognized case to the host and treating it as
illegal instruction instead of throwing a trace and treating it as a 'nop'.
Signed-off-by: Gustavo Romero <gromero@linux.ibm.com>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-By: Michael Neuling <mikey@neuling.org>
Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 103a8542cb35b5130f732d00b0419a594ba1b517 ]
If the hypervisor doesn't support hugepages, the kernel ends up allocating a large
number of page table pages. The early page table allocation was wrongly
setting the max memblock limit to ppc64_rma_size with radix translation
which resulted in boot failure as shown below.
Kernel panic - not syncing:
early_alloc_pgtable: Failed to allocate 16777216 bytes align=0x1000000 nid=-1 from=0x0000000000000000 max_addr=0xffffffffffffffff
CPU: 0 PID: 0 Comm: swapper Not tainted 5.8.0-24.9-default+ #2
Call Trace:
[c0000000016f3d00] [c0000000007c6470] dump_stack+0xc4/0x114 (unreliable)
[c0000000016f3d40] [c00000000014c78c] panic+0x164/0x418
[c0000000016f3dd0] [c000000000098890] early_alloc_pgtable+0xe0/0xec
[c0000000016f3e60] [c0000000010a5440] radix__early_init_mmu+0x360/0x4b4
[c0000000016f3ef0] [c000000001099bac] early_init_mmu+0x1c/0x3c
[c0000000016f3f10] [c00000000109a320] early_setup+0x134/0x170
This was because the kernel was checking for the radix feature before we enable the
feature via mmu_features. This resulted in the kernel using hash restrictions on
radix.
Rework the early init code such that the kernel boot with memblock restrictions
as imposed by hash. At that point, the kernel still hasn't finalized the
translation the kernel will end up using.
We have three different ways of detecting radix.
1. dt_cpu_ftrs_scan -> used only in case of PowerNV
2. ibm,pa-features -> Used when we don't use cpu_dt_ftr_scan
3. CAS -> Where we negotiate with hypervisor about the supported translation.
We look at 1 or 2 early in the boot and after that, we look at the CAS vector to
finalize the translation the kernel will use. We also support a kernel command
line option (disable_radix) to switch to hash.
Update the memblock limit after mmu_early_init_devtree() if the kernel is going
to use radix translation. This forces some of the memblock allocations we do before
mmu_early_init_devtree() to be within the RMA limit.
Fixes: 2bfd65e45e ("powerpc/mm/radix: Add radix callbacks for early init routines")
Reported-by: Shirisha Ganta <shiganta@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200828100852.426575-1-aneesh.kumar@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fdfe7cbd58806522e799e2a50a15aee7f2cbb7b6 upstream.
The 'flags' field of 'struct mmu_notifier_range' is used to indicate
whether invalidate_range_{start,end}() are permitted to block. In the
case of kvm_mmu_notifier_invalidate_range_start(), this field is not
forwarded on to the architecture-specific implementation of
kvm_unmap_hva_range() and therefore the backend cannot sensibly decide
whether or not to block.
Add an extra 'flags' parameter to kvm_unmap_hva_range() so that
architectures are aware as to whether or not they are permitted to block.
Cc: <stable@vger.kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Message-Id: <20200811102725.7121-2-will@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c83b277ada72b585e6a3e52b067669df15bcedb upstream.
Recently random.h started including percpu.h (see commit
f227e3ec3b5c ("random32: update the net random state on interrupt and
activity")), which broke corenet64_smp_defconfig:
In file included from /linux/arch/powerpc/include/asm/paca.h:18,
from /linux/arch/powerpc/include/asm/percpu.h:13,
from /linux/include/linux/random.h:14,
from /linux/lib/uuid.c:14:
/linux/arch/powerpc/include/asm/mmu.h:139:22: error: unknown type name 'next_tlbcam_idx'
139 | DECLARE_PER_CPU(int, next_tlbcam_idx);
This is due to a circular header dependency:
asm/mmu.h includes asm/percpu.h, which includes asm/paca.h, which
includes asm/mmu.h
Which means DECLARE_PER_CPU() isn't defined when mmu.h needs it.
We can fix it by moving the include of paca.h below the include of
asm-generic/percpu.h.
This moves the include of paca.h out of the #ifdef __powerpc64__, but
that is OK because paca.h is almost entirely inside #ifdef
CONFIG_PPC64 anyway.
It also moves the include of paca.h out of the #ifdef CONFIG_SMP,
which could possibly break something, but seems to have no ill
effects.
Fixes: f227e3ec3b5c ("random32: update the net random state on interrupt and activity")
Cc: stable@vger.kernel.org # v5.8
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200804130558.292328-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df4d4ef22446b3a789a4efd74d34f2ec1e24deb2 ]
We have two uses of CONFIG_BOOK3S_601, which doesn't exist. Fix them
to use CONFIG_PPC_BOOK3S_601 which is the correct symbol.
Fixes: 12c3f1fd87 ("powerpc/32s: get rid of CPU_FTR_601 feature")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200724131728.1643966-5-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c9450c053f88e525b2db1e6990cdf34d14e7696 ]
Compilation error:
arch/powerpc/perf/perf_regs.c:80:undefined reference to `.is_sier_available'
Currently is_sier_available() is part of core-book3s.c, which is added
to build based on CONFIG_PPC_PERF_CTRS.
A config with CONFIG_PERF_EVENTS and without CONFIG_PPC_PERF_CTRS will
have a build break because of missing is_sier_available().
In practice it only breaks when CONFIG_FSL_EMB_PERF_EVENT=n because
that also guards the usage of is_sier_available(). That only happens
with CONFIG_PPC_BOOK3E_64=y and CONFIG_FSL_SOC_BOOKE=n.
Patch adds is_sier_available() in asm/perf_event.h to fix the build
break for configs missing CONFIG_PPC_PERF_CTRS.
Fixes: 333804dc3b ("powerpc/perf: Update perf_regs structure to include SIER")
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
[mpe: Add detail about CONFIG_FSL_SOC_BOOKE]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200614083604.302611-1-maddy@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec2fc2a9e9bbad9023aab65bc472ce7a3ca8608f ]
Partition suspension, used for hibernation and migration, requires
that the OS place all but one of the LPAR's processor threads into one
of two states prior to calling the ibm,suspend-me RTAS function:
* the architected offline state (via RTAS stop-self); or
* the H_JOIN hcall, which does not return until the partition
resumes execution
Using H_CEDE as the offline mode, introduced by
commit 3aa565f53c ("powerpc/pseries: Add hooks to put the CPU into
an appropriate offline state"), means that any threads which are
offline from Linux's point of view must be moved to one of those two
states before a partition suspension can proceed.
This was eventually addressed in commit 120496ac2d ("powerpc: Bring
all threads online prior to migration/hibernation"), which added code
to temporarily bring up any offline processor threads so they can call
H_JOIN. Conceptually this is fine, but the implementation has had
multiple races with cpu hotplug operations initiated from user
space[1][2][3], the error handling is fragile, and it generates
user-visible cpu hotplug events which is a lot of noise for a platform
feature that's supposed to minimize disruption to workloads.
With commit 3aa565f53c ("powerpc/pseries: Add hooks to put the CPU
into an appropriate offline state") reverted, this code becomes
unnecessary, so remove it. Since any offline CPUs now are truly
offline from the platform's point of view, it is no longer necessary
to bring up CPUs only to have them call H_JOIN and then go offline
again upon resuming. Only active threads are required to call H_JOIN;
stopped threads can be left alone.
[1] commit a6717c01dd ("powerpc/rtas: use device model APIs and
serialization during LPM")
[2] commit 9fb603050f ("powerpc/rtas: retry when cpu offline races
with suspend/migration")
[3] commit dfd718a2ed ("powerpc/rtas: Fix a potential race between
CPU-Offline & Migration")
Fixes: 120496ac2d ("powerpc: Bring all threads online prior to migration/hibernation")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-3-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b506923ee44ae87fc9f4de16b53feb313623e146 upstream.
This reverts commit d2a91cef9bbdeb87b7449fdab1a6be6000930210.
This commit moved too much work in kasan_init(). The allocation
of shadow pages has to be moved for the reason explained in that
patch, but the allocation of page tables still need to be done
before switching to the final hash table.
First revert the incorrect commit, following patch redoes it
properly.
Fixes: d2a91cef9bbd ("powerpc/kasan: Fix shadow pages allocation failure")
Cc: stable@vger.kernel.org
Reported-by: Erhard F. <erhard_f@mailbox.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208181
Link: https://lore.kernel.org/r/3667deb0911affbf999b99f87c31c77d5e870cd2.1593690707.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c2e929b18cea6cbf71364f22d742d9aad7f4677a ]
Booting a power9 server with hash MMU could trigger an undefined
behaviour because pud_offset(p4d, 0) will do,
0 >> (PAGE_SHIFT:16 + PTE_INDEX_SIZE:8 + H_PMD_INDEX_SIZE:10)
Fix it by converting pud_index() and friends to static inline
functions.
UBSAN: shift-out-of-bounds in arch/powerpc/mm/ptdump/ptdump.c:282:15
shift exponent 34 is too large for 32-bit type 'int'
CPU: 6 PID: 1 Comm: swapper/0 Not tainted 5.6.0-rc4-next-20200303+ #13
Call Trace:
dump_stack+0xf4/0x164 (unreliable)
ubsan_epilogue+0x18/0x78
__ubsan_handle_shift_out_of_bounds+0x160/0x21c
walk_pagetables+0x2cc/0x700
walk_pud at arch/powerpc/mm/ptdump/ptdump.c:282
(inlined by) walk_pagetables at arch/powerpc/mm/ptdump/ptdump.c:311
ptdump_check_wx+0x8c/0xf0
mark_rodata_ro+0x48/0x80
kernel_init+0x74/0x194
ret_from_kernel_thread+0x5c/0x74
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20200306044852.3236-1-cai@lca.pw
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ffa8b7dc11752827329e4e84a574ea6aaf24716 ]
Aneesh increased the size of struct pt_regs by 16 bytes and started
seeing this WARN_ON:
smp: Bringing up secondary CPUs ...
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at arch/powerpc/kernel/process.c:455 giveup_all+0xb4/0x110
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.7.0-rc2-gcc-8.2.0-1.g8f6a41f-default+ #318
NIP: c00000000001a2b4 LR: c00000000001a29c CTR: c0000000031d0000
REGS: c0000000026d3980 TRAP: 0700 Not tainted (5.7.0-rc2-gcc-8.2.0-1.g8f6a41f-default+)
MSR: 800000000282b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 48048224 XER: 00000000
CFAR: c000000000019cc8 IRQMASK: 1
GPR00: c00000000001a264 c0000000026d3c20 c0000000026d7200 800000000280b033
GPR04: 0000000000000001 0000000000000000 0000000000000077 30206d7372203164
GPR08: 0000000000002000 0000000002002000 800000000280b033 3230303030303030
GPR12: 0000000000008800 c0000000031d0000 0000000000800050 0000000002000066
GPR16: 000000000309a1a0 000000000309a4b0 000000000309a2d8 000000000309a890
GPR20: 00000000030d0098 c00000000264da40 00000000fd620000 c0000000ff798080
GPR24: c00000000264edf0 c0000001007469f0 00000000fd620000 c0000000020e5e90
GPR28: c00000000264edf0 c00000000264d200 000000001db60000 c00000000264d200
NIP [c00000000001a2b4] giveup_all+0xb4/0x110
LR [c00000000001a29c] giveup_all+0x9c/0x110
Call Trace:
[c0000000026d3c20] [c00000000001a264] giveup_all+0x64/0x110 (unreliable)
[c0000000026d3c90] [c00000000001ae34] __switch_to+0x104/0x480
[c0000000026d3cf0] [c000000000e0b8a0] __schedule+0x320/0x970
[c0000000026d3dd0] [c000000000e0c518] schedule_idle+0x38/0x70
[c0000000026d3df0] [c00000000019c7c8] do_idle+0x248/0x3f0
[c0000000026d3e70] [c00000000019cbb8] cpu_startup_entry+0x38/0x40
[c0000000026d3ea0] [c000000000011bb0] rest_init+0xe0/0xf8
[c0000000026d3ed0] [c000000002004820] start_kernel+0x990/0x9e0
[c0000000026d3f90] [c00000000000c49c] start_here_common+0x1c/0x400
Which was unexpected. The warning is checking the thread.regs->msr
value of the task we are switching from:
usermsr = tsk->thread.regs->msr;
...
WARN_ON((usermsr & MSR_VSX) && !((usermsr & MSR_FP) && (usermsr & MSR_VEC)));
ie. if MSR_VSX is set then both of MSR_FP and MSR_VEC are also set.
Dumping tsk->thread.regs->msr we see that it's: 0x1db60000
Which is not a normal looking MSR, in fact the only valid bit is
MSR_VSX, all the other bits are reserved in the current definition of
the MSR.
We can see from the oops that it was swapper/0 that we were switching
from when we hit the warning, ie. init_task. So its thread.regs points
to the base (high addresses) in init_stack.
Dumping the content of init_task->thread.regs, with the members of
pt_regs annotated (the 16 bytes larger version), we see:
0000000000000000 c000000002780080 gpr[0] gpr[1]
0000000000000000 c000000002666008 gpr[2] gpr[3]
c0000000026d3ed0 0000000000000078 gpr[4] gpr[5]
c000000000011b68 c000000002780080 gpr[6] gpr[7]
0000000000000000 0000000000000000 gpr[8] gpr[9]
c0000000026d3f90 0000800000002200 gpr[10] gpr[11]
c000000002004820 c0000000026d7200 gpr[12] gpr[13]
000000001db60000 c0000000010aabe8 gpr[14] gpr[15]
c0000000010aabe8 c0000000010aabe8 gpr[16] gpr[17]
c00000000294d598 0000000000000000 gpr[18] gpr[19]
0000000000000000 0000000000001ff8 gpr[20] gpr[21]
0000000000000000 c00000000206d608 gpr[22] gpr[23]
c00000000278e0cc 0000000000000000 gpr[24] gpr[25]
000000002fff0000 c000000000000000 gpr[26] gpr[27]
0000000002000000 0000000000000028 gpr[28] gpr[29]
000000001db60000 0000000004750000 gpr[30] gpr[31]
0000000002000000 000000001db60000 nip msr
0000000000000000 0000000000000000 orig_r3 ctr
c00000000000c49c 0000000000000000 link xer
0000000000000000 0000000000000000 ccr softe
0000000000000000 0000000000000000 trap dar
0000000000000000 0000000000000000 dsisr result
0000000000000000 0000000000000000 ppr kuap
0000000000000000 0000000000000000 pad[2] pad[3]
This looks suspiciously like stack frames, not a pt_regs. If we look
closely we can see return addresses from the stack trace above,
c000000002004820 (start_kernel) and c00000000000c49c (start_here_common).
init_task->thread.regs is setup at build time in processor.h:
#define INIT_THREAD { \
.ksp = INIT_SP, \
.regs = (struct pt_regs *)INIT_SP - 1, /* XXX bogus, I think */ \
The early boot code where we setup the initial stack is:
LOAD_REG_ADDR(r3,init_thread_union)
/* set up a stack pointer */
LOAD_REG_IMMEDIATE(r1,THREAD_SIZE)
add r1,r3,r1
li r0,0
stdu r0,-STACK_FRAME_OVERHEAD(r1)
Which creates a stack frame of size 112 bytes (STACK_FRAME_OVERHEAD).
Which is far too small to contain a pt_regs.
So the result is init_task->thread.regs is pointing at some stack
frames on the init stack, not at a pt_regs.
We have gotten away with this for so long because with pt_regs at its
current size the MSR happens to point into the first frame, at a
location that is not written to by the early asm. With the 16 byte
expansion the MSR falls into the second frame, which is used by the
compiler, and collides with a saved register that tends to be
non-zero.
As far as I can see this has been wrong since the original merge of
64-bit ppc support, back in 2002.
Conceptually swapper should have no regs, it never entered from
userspace, and in fact that's what we do on 32-bit. It's also
presumably what the "bogus" comment is referring to.
So I think the right fix is to just not-initialise regs at all. I'm
slightly worried this will break some code that isn't prepared for a
NULL regs, but we'll have to see.
Remove the comment in head_64.S which refers to us setting up the
regs (even though we never did), and is otherwise not really accurate
any more.
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200428123130.73078-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d2a91cef9bbdeb87b7449fdab1a6be6000930210 upstream.
Doing kasan pages allocation in MMU_init is too early, kernel doesn't
have access yet to the entire memory space and memblock_alloc() fails
when the kernel is a bit big.
Do it from kasan_init() instead.
Fixes: 2edb16efc8 ("powerpc/32: Add KASAN support")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c24163ee5d5f8cdf52fefa45055ceb35435b8f15.1589866984.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a66a24f6060e6775f8c02ac52329ea0152d7e58 upstream.
At the time being, KASAN_SHADOW_END is 0x100000000, which
is 0 in 32 bits representation.
This leads to a couple of issues:
- kasan_remap_early_shadow_ro() does nothing because the comparison
k_cur < k_end is always false.
- In ptdump, address comparison for markers display fails and the
marker's name is printed at the start of the KASAN area instead of
being printed at the end.
However, there is no need to shadow the KASAN shadow area itself,
so the KASAN shadow area can stop shadowing memory at the start
of itself.
With a PAGE_OFFSET set to 0xc0000000, KASAN shadow area is then going
from 0xf8000000 to 0xff000000.
Fixes: cbd18991e2 ("powerpc/mm: Fix an Oops in kasan_mmu_init()")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ae1a3c0d19a37410c209c3fc453634cfcc0ee318.1589866984.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey Zhizhikin