[ Upstream commit 2270ad2f4e123336af685ecedd1618701cb4ca1e ]
This patch fixes the tristate and pullup configuration for UART 1 to 3
on the Tamonten SOM.
Signed-off-by: Andreas Obergschwandtner <andreas.obergschwandtner@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd7cd5b716d594e27a933c12f026d4f2426d7bf4 ]
PPD has only one ACHC device, which effectively is a Kinetis
microcontroller. It has one SPI interface used for normal
communication. Additionally it's possible to flash the device
firmware using NXP's EzPort protocol by correctly driving a
second chip select pin and the device reset pin.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210802172309.164365-3-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dc6c59892ead17a9febd11202c9f6794aac1895 ]
Since new code doesn't take old clk names in account, it does fixes
error:
msm_dsi 4700000.mdss_dsi: dev_pm_opp_set_clkname: Couldn't find clock: -2
and following kernel oops introduced by
b0530eb1191 ("drm/msm/dpu: Use OPP API to set clk/perf state").
Also removes warning about deprecated clock names.
Tested against linux-5.10.y LTS on Nexus 7 2013.
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210707131453.24041-1-david@ixit.cz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72ccc373b064ae3ac0c5b5f2306069b60ca118df ]
After enabling CONFIG_REGULATOR_DEBUG=y we observer below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: 087a1d8b4e ("ARM: dts: meson8b: ec100: add the VDDEE regulator")
Fixes: 3e7db1c1b7 ("ARM: dts: meson8b: ec100: improve the description of the regulators")
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-4-linux.amoon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 876228e9f935f19c7afc7ba394d17e2ec9143b65 ]
After enabling CONFIG_REGULATOR_DEBUG=y we observe below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: 524d96083b ("ARM: dts: meson8b: odroidc1: add the CPU voltage regulator")
Fixes: 8bdf38be71 ("ARM: dts: meson8b: odroidc1: add the VDDEE regulator")
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[narmstrong: fixed typo in commit s/observer/observe/]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-2-linux.amoon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44cf630bcb8c5ec78125805c9447dd5766792224 ]
We are seeing "imprecise external abort (0x1406)" errors during boot
(which then cause the whole board to hang) on Meson8 (but not Meson8m2).
These are observed while trying to access the GPU's registers when the
MALI clock is running at it's default setting of 24MHz. The 3.10 vendor
kernel uses 318.75MHz as "default" GPU frequency. Using that makes the
"imprecise external aborts" go away.
Add the assigned-clocks and assigned-clock-rates properties to also bump
the MALI clock to 318.75MHz before accessing any of it's registers.
Fixes: 7d3f6b536e ("ARM: dts: meson8: add the Mali-450 MP6 GPU")
Reported-by: Demetris Ierokipides <ierokipides.dem@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210711214023.2163565-1-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c295b7f3d01359ff4336fcb6e406e6ed37957d6 ]
The HVI3C shall be a group of I3C function, not an independent function.
Correct the function name from "HVI3C" to "I3C".
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Fixes: f510f04c8c ("ARM: dts: aspeed: Add AST2600 pinmux nodes")
Link: https://lore.kernel.org/r/20201029062723.20798-1-dylan_hung@aspeedtech.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47091f473b364c98207c4def197a0ae386fc9af1 ]
Once the new schema interrupt-controller/arm,vic.yaml is added, we get
the below warnings:
arch/arm/boot/dts/ste-nomadik-nhk15.dt.yaml:
intc@10140000: $nodename:0: 'intc@10140000' does not match
'^interrupt-controller(@[0-9a-f,]+)*$'
Fix the node names for the interrupt controller to conform
to the standard node name interrupt-controller@..
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210617210825.3064367-2-sudeep.holla@arm.com
Link: https://lore.kernel.org/r/20210626000103.830184-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20a6b3fd8e2e2c063b25fbf2ee74d86b898e5087 ]
Based on the latest timing specifications for the TPS65218 from the data
sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206
from November 2014, we must change the i2c bus speed to better fit within
the minimum high SCL time required for proper i2c transfer.
When running at 400khz, measurements show that SCL spends
0.8125 uS/1.666 uS high/low which violates the requirement for minimum
high period of SCL provided in datasheet Table 7.6 which is 1 uS.
Switching to 100khz gives us 5 uS/5 uS high/low which both fall above
the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low.
Without this patch occasionally a voltage set operation from the kernel
will appear to have worked but the actual voltage reflected on the PMIC
will not have updated, causing problems especially with cpufreq that may
update to a higher OPP without actually raising the voltage on DCDC2,
leading to a hang.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68ef4ad180e09805fa46965d15e1dfadf09ffa5 ]
This device tree include file describes a fixed-regulator
connecting smps7_reg output (1.8V) to some 1.8V rail and
consumers (vdds_1v8_main).
This regulator does not physically exist.
I assume it was introduced as a wrapper around smps7_reg
to provide a speaking signal name "vdds_1v8_main" as label.
This fixed-regulator without real function was not an issue
in driver code until
Commit 98e48cd9283d ("regulator: core: resolve supply for boot-on/always-on regulators")
introduced a new check for regulator initialization which
makes Palmas regulator registration fail:
[ 5.407712] ldo1: supplied by vsys_cobra
[ 5.412748] ldo2: supplied by vsys_cobra
[ 5.417603] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator
The reason is that the supply-chain of regulators is too
long and goes from ldo3 through the virtual vdds_1v8_main
regulator and then back to smps7. This adds a cross-dependency
of probing Palmas regulators and the fixed-regulator which
leads to probe deferral by the new check and is no longer
resolved.
Since we do not control what device tree files including this
one reference (either &vdds_1v8_main or &smps7_reg or both)
we keep both labels for smps7 for compatibility.
Fixes: 98e48cd9283d ("regulator: core: resolve supply for boot-on/always-on regulators")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d9e30a52047f2d464efdfd1d561ae1f707a0286 ]
The pinctrl_power_button/pinctrl_power_out each define single GPIO
pinmux, except it is exactly the other one than the matching gpio-keys
and gpio-poweroff DT nodes use for that functionality. Swap the two
GPIOs to correct this error.
Fixes: 50d29fdb76 ("ARM: dts: imx53: Add power GPIOs on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd8e83884fdd7b5fc411f201a58d8d01890198a2 ]
The AR803x PHY used on this modules seems to require the reset line to
be asserted for around 10ms in order to avoid rare cases where the PHY
gets stuck in an incoherent state that prevents it to function
correctly.
The previous value of 2ms was found to be problematic on some setups,
causing intermittent issues where the PHY would be unresponsive
every once in a while on some sytems, with a low occurrence (it typically
took around 30 consecutive reboots to encounter the issue).
Bumping the delay to the 10ms makes the issue dissapear, with more than
2500 consecutive reboots performed without the issue showing-up.
Fixes: 208d7baf80 ("ARM: imx: initial SolidRun HummingBoard support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Hervé Codina <herve.codina@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82a1c67554dff610d6be4e1982c425717b3c6a23 ]
Once the new schema interrupt-controller/arm,vic.yaml is added, we get
the below warnings:
arch/arm/boot/dts/versatile-ab.dt.yaml:
intc@10140000: $nodename:0: 'intc@10140000' does not match
'^interrupt-controller(@[0-9a-f,]+)*$'
arch/arm/boot/dts/versatile-ab.dt.yaml:
intc@10140000: 'clear-mask' does not match any of the regexes
Fix the node names for the interrupt controller to conform
to the standard node name interrupt-controller@.. Also drop invalid
clear-mask property.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210701132118.759454-1-sudeep.holla@arm.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f07edc41220b14ce057a4e6d7161b30688ddb8a2 ]
A test with rockchip-io-domain.yaml gives notifications
for supply properties in io-domains nodes.
Fix them all into ".*-supply$" format.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210606181632.13371-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf24b91f4baf7e421c770a1d9c7d381b10206ac9 ]
Fix following warning observed with "make dtbs_check W=1" command.
It concerns f429 eval and disco boards, f769 disco board.
Warning (unit_address_vs_reg): /gpio_keys/button@0: node has a unit name,
but no reg or ranges property
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2566d5b8c1670f7d7a44cc1426d254147ec5c421 ]
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b644c5e01c870056e13a096e14b9a92075c8f682 ]
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14cdc1f243d79e0b46be150502b7dba9c5a6bdfd ]
Serial interface uart3 on phyFLEX board is capable of 5-wire connection
including signals RTS and CTS for hardware flow control.
Fix signals UART3_CTS_B and UART3_RTS_B padmux assignments and add
missing property "uart-has-rtscts" to allow serial interface to be
configured and used with the hardware flow control.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 970cdc53cb1afa73602028c103dbfb6a230080be ]
Use more generic names (as recommended in the device tree specification
or the binding documentation)
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3bcbcd396175ac26aa54919c0b31c7d2878fc24 ]
Use more generic names (as recommended in the device tree specification
or the binding documentation)
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2948781a72f0d8cf2adf31758c357f2f35e6c79 ]
Use more generic names (as recommended in the device tree specification
or the binding documentation)
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b46d674ac000b101fdad92cf16cc11d90b72f86 ]
Fixed order is the device-tree convention.
The timer driver currently gets clocks by name,
so no changes are needed there.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: https://lore.kernel.org/r/20210506111136.3941-3-ezequiel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfbfb86a43f9a5bbd166d88bca9e07ee4e1bff31 ]
A test with the command below aimed at powerpc generates
notifications in the Rockchip ARM tree.
Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3036-kylin and rk3288
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc5b59b945b546e27977e99a5ca6fe61179ff0d2 ]
ethernet-phy is not the right name for mdio, fix it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddc873cd3c0af4faad6a00bffda21c3f775126dd ]
The i2c bus can freeze at the end of transaction so the bus can no longer work.
This scenario is improved by adding scl/sda gpios definitions to implement the
i2c bus recovery mechanism.
Fixes: 52c7a088ba ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2bdd3484890441b9cc2560413a86e8f2aa04157 ]
To make the ethernet cable plugin detection reliable the
power detection of the smsc phy has been disabled.
Fixes: 52c7a088ba ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c016c26c1631f539c652b5d82242a3ca402545c1 ]
Fix ethernet reset time properties as described in
Documentation/devicetree/bindings/net/ethernet-phy.yaml
Fixes: 52c7a088ba ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b11fec7345f21995f4ea4bafb0e108b9a620238 ]
ti,pindir-d0-out-d1-in property is expected to be of type boolean.
Therefore, fix the property accordingly.
Fixes: b0b039515445 ("ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Andrey Zhizhikin