Icenowy Zheng 3cfecee49c sunxi: set the default CPUx frequency of H5 to 816MHz ... Some H5 boards are designed to start at 1.1V CPUx voltage (e.g. Nano Pi NEO2), which may not work properly at 1008MHz if the chip's quality is not so good. Lower the default CPUx frequency of H5 to 816MHz. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Jagan Teki <jagan@openedev.com>		2017-12-02 21:55:25 +05:30
..
dram_timings	sunxi: add LPDDR3 timing from stock boot0	2017-06-08 22:37:55 +05:30
board.c	arm: sunxi: Move spl_boot_device in a separate function	2017-10-03 19:12:06 +02:00
clock_sun4i.c	sunxi: Move cpu independent code to mach directory	2016-04-01 09:52:28 +02:00
clock_sun6i.c	sunxi: switch PRCM to non-secure on H3/H5 SoCs	2017-08-11 15:49:39 +05:30
clock_sun8i_a83t.c	sunxi: Move cpu independent code to mach directory	2016-04-01 09:52:28 +02:00
clock_sun9i.c	sunxi: add initial clock setup for sun9i for SPL	2016-10-30 11:38:04 +01:00
clock.c	sunxi: add gtbus-initialisation for sun9i	2016-10-30 11:38:04 +01:00
cpu_info.c	sunxi: add basic V3s support	2017-04-21 09:23:17 +02:00
dram_helpers.c	ARM: Rework and correct barrier definitions	2016-08-05 07:23:57 -04:00
dram_sun4i.c	sunxi: Move cpu independent code to mach directory	2016-04-01 09:52:28 +02:00
dram_sun6i.c	sunxi: Move cpu independent code to mach directory	2016-04-01 09:52:28 +02:00
dram_sun8i_a23.c	sunxi: Move cpu independent code to mach directory	2016-04-01 09:52:28 +02:00
dram_sun8i_a33.c	sunxi: Move cpu independent code to mach directory	2016-04-01 09:52:28 +02:00
dram_sun8i_a83t.c	sunxi: Move cpu independent code to mach directory	2016-04-01 09:52:28 +02:00
dram_sun9i.c	sunxi: DRAM initialisation for sun9i	2016-10-30 11:38:04 +01:00
dram_sunxi_dw.c	sunxi: add LPDDR3 DRAM type support for DesignWare-like DRAM controller	2017-06-08 22:37:55 +05:30
gtbus_sun9i.c	sunxi: add gtbus-initialisation for sun9i	2016-10-30 11:38:04 +01:00
Kconfig	sunxi: set the default CPUx frequency of H5 to 816MHz	2017-12-02 21:55:25 +05:30
Makefile	sunxi: Add selective DRAM type and timing	2017-06-08 22:37:55 +05:30
p2wi.c	sunxi: Move cpu independent code to mach directory	2016-04-01 09:52:28 +02:00
pinmux.c	sunxi: Move cpu independent code to mach directory	2016-04-01 09:52:28 +02:00
pmic_bus.c	sunxi: Enable AXP221s in I2C mode with the R40 SoC	2017-04-20 13:30:00 +02:00
prcm.c	sunxi: Move cpu independent code to mach directory	2016-04-01 09:52:28 +02:00
rmr_switch.S	sunxi: A64: do an RMR switch if started in AArch32 mode	2017-01-04 16:37:42 +01:00
rsb.c	sunxi: Move cpu independent code to mach directory	2016-04-01 09:52:28 +02:00
usb_phy.c	sunxi: usb_phy: invert the USB phy_ctl condition	2017-10-03 19:12:06 +02:00