OF_CONTROL is setup by default and memory reading is done via DT. Remove
all config files with memory references.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Specify max_bus_width directly in usdhc_cfg static definition instead
of tweaking it in the board_mmc_init() function.
Signed-off-by: Julien Corjon <corjon.j@ecagroup.com>
USDHC2 does not exist on mx6quq7 board, as USDHC4 was already been
declared this is probably a typo.
Signed-off-by: Julien Corjon <corjon.j@ecagroup.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
When running the 'ums' command we get:
=> ums 0 mmc 0
UMS: disk start sector: 0x0, count: 0xe18000
g_dnl_register: failed!, error: -22
ERROR: g_dnl_register failed
at common/cmd_usb_mass_storage.c:107/do_usb_mass_storage()
Fix this by initializing USB OTG1 port as USB device mode instead of host.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This adds basic support to Intel Cougar Canyon 2 board, a board
based on Chief River platform with an Ivy Bridge processor and
a Panther Point chipset.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Versatile Industrial Communication platform is a community oriented
board from Landis + Gyr. It comes with:
- an RS-485 port
- 2 Ethernet ports
- a wireless M-BUS
- a 4G modem
- a 4MB SPI flash
- a 4GB eMMC
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[rebase on current TOT]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add support for DENX MA5D4 SoM and MA5D4EVK board, based on the
Atmel SAMA5D4 SoC. The SoM contains the SoC, eMMC, SPI NOR, SPI
CAN controllers and DRAM, the baseboard contains UART connectors,
ethernet port, microSD slot, LCD header, 2x CAN connector and a
lot of expansion headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the PMC_PLLICPR init function, use this
function to clean up the code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the new PLLB clock handle functions,
use these functions to clean up the PLLB enable code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Heiko Schocher <hs@denx.de>
Due to introducing the new UTMI PLL clock handle functions,
use the functions to reduce the duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the new peripheral clock handle functions,
use these functions to reduce duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
[Rebased on current master, fixup for at91rm9200ek]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Move this driver over to use driver model. This involves rearranging the
code somewhat. The effect is that everything is run from the probe() method.
Boards which use this are fixed up, but only seaboard is tested.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This option refers only to the tegra20 video driver, so name it as such
to avoid confusion with tegra124.
Also move this option to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
According to Data Manual(SPRS915P) of AM572x, TI QSPI controller on
DRA74 EVM(rev 1.1+) can support up to 64MHz in MODE-0, whereas MODE-3 is
limited to 48MHz. Hence, switch to MODE-0 for better throughput.
Also, add IODelay parameters for the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
I will take this over from Peter Barada, since I work with it daily
at Logic PD.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peter Barada <peter.barada@logicpd.com>
There are various different boards with the same hardware sold as LG Optimus
Black, such as P970, P970g and KU5900. Since this port is functional for all
variants, it doesn't make sense to keep references to P970.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Let's set "ethaddr" when we get the ethernet address too, so that
fdt_fixup_ethernet() sets the address in the device tree and the Linux
driver can pick it up.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
remove board_eth_init when CONFIG_DM_ETH is defined
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Android Fastboot requires USB. The TWL4030 PMIC on omap3_logic handles USB traffic.
This patch sets up the USB gadget and Android Fastboot to match what is done in the
omap3_beagle project.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Previously, Omap3_logic assumed X-loader was present. With this
patch, we can finally replace X-loader with an MLO generated by
U-Boot. This requires ECC to be setup to match the Linux Kernel
and the PBIAS confgured for the SD card.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The P5 header was not present on "Model B" any board prior to Revision 2.0,
there's no need for a separate device tree.
Also, it looks like "rev2" is incorrectly used to only cover the 512MiB
memory models; there also were 256MiB 2.0 boards.
I don't have all of the boards to check this, I'm following this table:
http://elinux.org/RPi_HardwareHistory#Board_Revision_History
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
This source has been blessed by Dom Cobley at the RPi Foundation, so seems
like the best source to refer to. It's a superset of and consistent with
the other sources.
Cc: Lubomir Rintel <lkundrak@v3.sk>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
This patch removes the uart clock enable from serial driver & move it in the
board code.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
asm/arch/gpio.h is not needed anymore as we get the GPIO base from
PCH driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Implement board_mmc_get_env_dev for the boards.
Following is examples:
SD1/SD2/SD3: return devno;
SD2/SD3: return devno - 1;
SD2/SD4: if (devno == 2), return dev - 2; return dev - 1;
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Move mmc_get_env_devno to soc.c and rename to mmc_get_env_dev to
match the one in common/env_mmc.c.
Introduce a weak function board_mmc_get_env_dev. Different
boards can implement this according to sdhc controller which
is used by the board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The i.MX6SX SABRESD board supports MCIMX28LCD (800x480x24) at LCDIF1
port, enable this display feature by adding relevant BSP codes
and configurations.
Signed-off-by: Ye Li <ye.li@nxp.com>
The BOOTCFG value used by bmode for SABRESD eMMC boot are actually for SD card.
Fixed the value to correct one.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
According to the LAN8720 datasheet tpurstd (time that reset line should
stay asserted) is 25ms.
So do as suggested by the LAN8720 datasheet.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Since commit 59370f3fcd ("net: phy: delay only if reset handler is
registered") Ethernet is no longer functional.
This commit does not have an issue in itself, but it revelead a problem
with the Ethernet initialization.
According to the LAN8720 datasheet tpurstd (time that reset line should
stay asserted) is 25ms.
So do as suggested in order to have Ethernet working again.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Initial version for mx6sx SABREAUTO board support with features:
PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander.
Signed-off-by: Ye Li <ye.li@nxp.com>
Enable the DDR calibration functionality on Novena to deal with the
memory SoDIMM on this board. Moreover, tweak the initial DDR DRAM
parameters so the calibration works properly.
Signed-off-by: Marek Vasut <marex@denx.de>
The sama5d2 Xplained SPL supports the boot medias: spi flash
and SD Card.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add struct atmel_mpddrc_config to accommodate the mpddrc register
configurations, not using the mpddrc register map structure,
struct atmel_mpddrc, in order to increase readability and reduce
run-time memory use.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
This adds support for Microchip PIC32MZ[DA] StarterKit board
based on a PIC32MZ[DA] family of microcontroller.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Rather than passing the I/O port base address to the Super I/O code,
switch it to using outb such that it makes use of the I/O port base
address automatically.
Drop the extern keyword to satisfy checkpatch whilst here.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Set the I/O port base earlier, from board_early_init_f, in preparation
for it being used by the serial driver.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
