Warm reset on OMAP5 freezes when USB cable is connected.
Fix requires PRM_RSTTIME.RSTTIME1 to be programmed
with the time for which reset should be held low for the
voltages and the oscillator to reach stable state.
There are 3 parameters to be considered for calculating
the time, which are mostly board and PMIC dependent.
-1- Time taken by the Oscillator to shut + restart
-2- PMIC OTP times
-3- Voltage rail ramp times, which inturn depends on the
PMIC slew rate and value of the voltage ramp needed.
In order to keep the code in u-boot simple, have a way
for boards to specify a pre computed time directly using
the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
option. If boards fail to specify the time, use a default
as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead.
Using the default value translates into some ~22ms and should work in
all cases.
However in order to avoid this large delay hiding other bugs,
its recommended that all boards look at their respective data
sheets and specify a pre computed and optimal value using
'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
In order to help future board additions to compute this
config option value, add a README at doc/README.omap-reset-time
which explains how to compute the value. Also update the toplevel
README with the additional option and pointers to
doc/README.omap-reset-time.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[rnayak@ti.com: Updated changelog and added the README]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Adding new board files for DRA7XX socs.
The pad registers layout is changed completely from OMAP5
So introducing the new structure here and also adding the
minimal data.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Adapt omap_mmc_init call for last 2 params]
Signed-off-by: Tom Rini <trini@ti.com>
After power-up SRCOMP cells are by-passed by default in OMAP5.
Software has to enable these SRCOMP sells.
For ES2: All 5 SRCOMP cells needs to be enabled.
For ES1: Only 4 SRCOMP cells in core power domain are enabled.
The 1 in wkup domain is not enabled because smart i/os
of wkup domain work with default compensation code.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Tom Rini <trini@ti.com>
There is some code duplication in the ddr io settings code.
This is avoided by moving the data to a Soc specific place and
letting the code generic.
This avoids unnessecary code addition for future socs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
The current PRCM structure prototype directly matches the hardware
register layout. So there is a need to change this for every new silicon
revision which has register space changes.
Avoiding this by making the prototye generic and populating the register
addresses seperately for all Socs.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Only omap4/5 currently have a meaningful set of display text and overo
had been adding a function to display nothing. Change how this works to
be opt-in and only turned on for omap4/5 now.
Signed-off-by: Tom Rini <trini@ti.com>
Errata ID:i727
Description: The refresh rate is programmed in the EMIF_SDRAM_REF_CTRL[15:0]
REG_REFRESH_RATE parameter taking into account frequency of the device.
When a warm reset is applied on the system, the OMAP processor restarts
with another OPP and so frequency is not the same. Due to this frequency
change, the refresh rate will be too low and could result in an unexpected
behavior on the memory side.
Workaround:
The workaround is to force self-refresh when coming back from the warm reset
with the following sequence:
• Set EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE to 0x2
• Set EMIF_PWR_MGMT_CTRL[7:4] REG_SR_TIM to 0x0
• Do a dummy read (loads automatically new value of sr_tim)
This will reduce the risk of memory content corruption, but memory content
can't be guaranteed after a warm reset.
This errata is impacted on
OMAP4430: 1.0, 2.0, 2.1, 2.2, 2.3
OMAP4460: 1.0, 1.1
OMAP4470: 1.0
OMAP5430: 1.0
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Certain modules are not affected by means of
a warm reset and need not be configured again.
Adding an API to detect the reset reason warm/cold.
This will be used to skip the module configurations
that are retained across a warm reset.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The different silicon revision variable names was defined for OMAP4 and
OMAP5 socs. Making the variable common so that some code can be
made generic.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
OMAP Voltage controller is used to generically talk to
PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code
in multiple SoC code, introduce a common voltage controller
logic which can be re-used from elsewhere.
With this change, we replace setup_sri2c with omap_vc_init which
has the same functionality, and replace the voltage scale
replication in do_scale_vcore and do_scale_tps62361 with
omap_vc_bypass_send_value. omap_vc_bypass_send_value can also
now be used with any configuration of PMIC.
NOTE: Voltage controller controlling I2C_SR is a write-only data
path, so no register read operation can be implemented.
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Configuration header(CH) is 512 byte header attached to an OMAP
boot image that will help ROM code to initialize clocks, SDRAM
etc and copy U-Boot directly into SDRAM. CH can help us in
by-passing SPL and directly boot U-boot, hence it's an alternative
for SPL. However, we intend to support both CH and SPL for OMAP4/5.
Initialization done through CH is limited and is not equivalent
to that done by SPL. So U-Boot has to distinguish between the
two cases and handle them accordingly. This patch takes care
of doing this.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Adding the correct configurations required for
dplls, clocks, for omap5 Soc.
Also changes are done to retain some part of the code common
for OMAP4/5 and move only the remaining to the Soc specific
directories.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.
OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
