Fix the building warning as below:
---8<----
Warning (reg_format): "reg" property in /i2c-gpio-0/pcf8563@50 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /i2c-gpio-0/pcf8563@50
Warning (avoid_default_addr_size): Relying on default #size-cells value for /i2c-gpio-0/pcf8563@50
--->8----
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete
duplicated definitions of enum dma_data_direction.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add space around operator "+", make it
match the coding style.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Macro VA_BITS and PTE_BLOCK_BITS are not used
in the code, so remove them.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This allows to scan the DT including all "clocks" node's sub-nodes
in which fixed-clock are defined.
All fixed-clock should be defined inside a clocks node which collect all
external oscillators. Until now, all clocks sub-nodes can't be binded except
if the "simple-bus" compatible string is added which is a hack.
Update test.dts by moving clk_fixed node inside clocks.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a convenience macro to iterate over subnodes of a node. Make use of
this where appropriate in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert SANDBOX_BITS_PER_LONG to Kconfig and assign it a correct
number depending on which host we are going to build and run.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It seems most of the time we are building and running sandbox on 64-bit host.
But we do support 32-bit host as well. Introduce Kconfig option for this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the code to set the ethernet mac address from eeprom by using
the common code from the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace the code to set the ethernet mac address with the code from
the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Create board/$(VENDOR)/common folder to accommodate the common code
shared by other atmel boards, now put the code to set ethernet mac
address from eeprom, which uses the i2c eeprom driver.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for selecting proper dtb for
am57xx BeagleBoard X15 revC u-boot from FIT
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
AM571x supports DDR running at 666MHz. Right now it is
clocked at 532MHz which is lower than what is supported.
In order to have maximum performance on AM571-IDK,
switch DDR to 666MHz.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for selecting proper dtb for
dra76x u-boot from FIT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Separate out u-boot specific compatibles from dts files.
This will help in syncing dts files in future.
Also these will get deleted eventually once respective drivers
are capable of handling Linux dts files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
dra76-evm has the ddr parts connectedi running at 666MHz:
EMIF1: MT41K512M16HA-125 AIT:A x 2
EMIF2: MT41K512M8RH-125-AAT:E x 4
Add support for configuring the above DDR parts.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76-evm uses lp8736 and tps65917 pmic for powering on
various peripherals. Add data for these pmics and register
for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76 family is a high-performance, infotainment application
device, based on OMAP architecture on a 28-nm technology.
This contains most of the subsystems, peripherals that are
available on dra74, dra72 family. This SoC mainly features
Subsystems:
- 2 x Cortex-A15 with max speed of 1.8GHz
- 2 X DSP
- 2 X Cortex-M4 IPU
- ISS
- CAL
- DSS
- VPE
- VIP
Connectivity peripherals:
- 1 USB3.0 and 3 USB2.0 subsystems
- 1 x SATA
- 2 x PCI Express Gen2
- 3-port Gigabit ethernet switch
- 2 x CAN
- MCAN
Adding CPU detection support for the dra76 ES1.0 soc
and update prcm, control module, dplls data.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
LP87565 is present on dra76-evm. Select it for
TARGET_DRA7XX_EVM.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It is not necessary that ldo1 is used to power on mmc.
So, add support for passing ldo registers for powering on mmc.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
It is not necessary all omap5+ based uses the same PMIC
to poweron mmc. So add support for enabling mmc based on board.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
CCN-504 HPF registers were believed to be accessible only from EL3.
However, recent tests proved otherwise. Remove checking for exception
level to re-enable L3 cache flushing for all levels.
Signed-off-by: York Sun <york.sun@nxp.com>
Tested-by: Zhao Qiang <qiang.zhao@nxp.com>
The pcie config space of ls1088a is different from ls2080a.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In case high region memory doesn't have enough space for Management
Complex (MC), the return value should indicate a failure so the
caller can handle it accordingly.
Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Ebony Zhu <ebony.zhu@nxp.com>
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Low Frequency Periodic Singaling (LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receive
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values.
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Low Frequency Periodic Signaling(LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter
settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receiver
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds support for RGMII protocol
NXP's LDPAA2 support RGMII protocol. LS1088A is the
first Soc supporting both RGMII and SGMII.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch add support of LS1088AQDS platform.
The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>
WIP: disable NAND for LS1088ARDB
For QSPI and IFC addresses execution shouldn't be allowed
when u-boot running from DDR. Revise the MMU final table
to enforce execute-never bits.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
According current code base, CONFIG_LS1012A should be
CONFIG_ARCH_LS1012A, or function fsl_fdt_disable(blob) will be
wrongly called to disable all dwc3 USB nodes on LS1012A, which
cause Linux USB function stop working at all.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080 family has CCN-504 cache coherent interconnet. Other SoCs
in LSCH3 family may have differnt interconnect.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Adds header address for PPA to be validated during ESBC phase for
ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It
must be initialized before the PPA.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Unify memory map for Layerscape based platforms. This patch includes
changes in bootscript, bootscript header and PPA header addresses
change as per unified memory map.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.
This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message, squashed patches for armv8 and armv7]
Reviewed-by: York Sun <york.sun@nxp.com>
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig.
Update defconfigs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on
USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and
LAN78XX options under new menu. Finally update the defconfigs that need
CONFIG_USB_HOST_ETHER.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With Makefiles testing for $(SPL_TPL_)SYSRESET, we need SPL_SYSRESET
for do_reset() in SPL for Rockchip SoCs.
References: 87c16d4 "drivers: spl: consistently use the $(SPL_TPL_) macro"
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
syscon id table need a dummy member as NULL ending, or else system
will panic while try to match a compatible in this table as a list.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Sometimes it's helpful to know the reset reason caused in the SoC.
Add reset reason detection for the RK3288 SoC.
This will set an environment variable which represents the reset reason.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The IPSR18 register bits were missing from the R8A7795 ES2.0+ PFC
tables, which triggered a BUG() in sh_pfc driver. This is because
of an out-of-bounds access to the pinmux_gpios[] array in the PFC
tables, which was too short due to the missing IPSR18 bits.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
It was noticed a few times, that the reboot from Linux (reboot command)
is different from the reboot (reset command) under U-Boot. The U-Boot
version does seem to reset the board more deeply (PCI cards etc) than
the Linux reboot.
This is actually caused by missing full reset bit in the reset register
value in the ACPI FADT table.
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SPL_OMAP3_ID_NAND
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_I2C_BUS_MAX
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Fix AM43XX drop AM44XX]
Signed-off-by: Tom Rini <trini@konsulko.com>
For consistency with other platforms and in preparation of Kconfig
migration, let's change Several TI platforms that use I2C_BUS_MAX
to CONFIG_SYS_I2C_BUS_MAX
Signed-off-by: Adam Ford <aford173@gmail.com>
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's
not strictly part of fastboot.
- Add some defaults for the fastboot buffer location and size
- Migrate all options listed in cmd/fastboot/Kconfig
- Cleanup the README
Signed-off-by: Tom Rini <trini@konsulko.com>
SUNXI_GMAC was still used to configure the code where as the
same has been renamed and moved to Kconfig in below commit
"sunxi: Move SUNXI_GMAC to Kconfig"
(sha1: 4d43d065db)
Signed-off-by: Dave Prue <dave@prue.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
[Tweek commit message, config_whitelist.txt, build-whitelist.sh]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Memory dt node update introduced by spl_fixup_fdt() in below
commit was making DDR configuration in-appropriate
to boot falcon mode. Hence added dram_init_banksize for
explicit assignment of proper base and size of DDR.
"boot: fdt: Perform arch_fixup_fdt() on the given device tree for falcon boot"
(sha1: 6e7585bb64)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The NXP i.MX 6UL and 6ULL do not support SATA and have no SATA
boot mode, hence remove it from the boot device detecion. This
fixes a build error introduced with 3bd1642d4d ("imx: fix USB
boot mode detection for i.MX 6UL and 6ULL")
Fixes: 3bd1642d4d ("imx: fix USB boot mode detection for i.MX 6UL and 6ULL")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
U-boots spi-nor support is currently considered a work in progress. For
now to avoid issues it is necessary to add a "spi-flash" compatible
string. Eventually the "jedec,spi-nor" will be sufficient when the core
U-boot code is updated to support it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This imply was added when the option was moved by the moveconfig tool,
but the intention is not clear. Move it to defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is now set up by the pinctrl driver when the NAND driver is
probed. Remove the legacy code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The new SoC PXs3 changed the address of PLL, but still uses the
same PLL name. We can not define SC_*PLLCTRL in the common header.
Move them to per-SoC .c file. Also, fix some PLL comments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The #include <common.h> was added for mdelay(). Later, the declaration
of mdelay was moved to <linux/delay.h> by commit 5bc516ed66 ("delay:
collect {m, n, u}delay declarations to include/linux/delay.h").
There is no need to include <common.h> now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The soc_boot_modes array is only used by bmode command
and not needed in SPL. Don't include it into SPL.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
There is no need to clear the control register 100 times in a
loop, a single zero write clears the register. I didn't find any
justification why clearing this register in a loop is needed
(no info in i.MX6 errata or GPT timer linux driver, linux driver
uses single write to clear this control register).
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
The eMMC controller for the A83T uses the new operating mode. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Almost all of the newer Allwinner SoCs have a new operating mode for the
eMMC clocks that needs to be enabled in both the clock and the MMC
controller.
Details about that mode are sparse, and the name itself (new mode vs old
mode) doesn't give much details, but it seems that the it changes the
sampling of the MMC clock. One side effect is also that it divides the
parent clock rate by 2.
Add support for it through a Kconfig option.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Since the gpr_init() function is common for boards using MX6S, MX6DL, MX6D,
MX6Q and MX6QP processors move it to the soc.c file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
While it is true that we no longer have 'ppcenv' and similar sections,
including env/embedded.o at all results in the text/etc sections being
available for the rest of the link. This in turn is required for the
setup used on ms7722se. This also, likely, needs further fine-tuning.
Fixes: f40ad66fa0 ("arch/sh: don't bring common/env_embedded.o into the link")
Signed-off-by: Tom Rini <trini@konsulko.com>
With this change, it will be possible to de-select falcon mode & spl
will only boot U-Boot.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Suggested-by: Bo Shen <voice.shen@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
kASLR support in kernel requires a random number to be passed via
chosen/kaslr-seed propert. sec_firmware generates this random seed
which can then be passed in the device tree node.
sec_firmware reserves JR3 for it's own usage. Node for JR3 is
removed from device-tree.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
do_switch_ecc() calls fsmc_nand_switch_ecc(), which is a direct
function call into drivers/mtd/nand/fsmc_nand.c. However, this
function is not guarded by CONFIG_NAND_FSMC, which results to a build
failure if CONFIG_NAND_FSMC is disabled.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The code in board/spear/common/ is not board-specific but
SoC-specific. Therefore, boards from other vendors than "spear" may
want to re-use this code, which is currently difficult with the code
being placed in board/spear/common/.
Since this code really is SoC-specific, this commit moves it to
arch/arm/cpu/arm926ejs/spear/, with the rest of the SPEAr related
code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The function interrupt_init_cpu() is given an int return type but does
not return anything but 0. Rework this to be a void function.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Mario Six <mario.six@gdsys.cc>
This re-syncs AM33xx DTS file with current file from
Linux v4.13-rc4 to ensure a consistent configuration. Upstream
Linux removed the redundant Interrupt-parent property from mmc,
mac, lcdc and tscadc sub nodes.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The linker script for SuperH brings the .ppcenv and .ppcenvr section
of common/env_embedded.o into the .text section. However, the .ppcenv
section is only ever filled in by env_embedded.o when
CONFIG_SYS_USE_PPCENV is defined, but no platforms in mainline U-Boot
use this.
In addition, common/env_embedded.o is not always built (when you use
CONFIG_ENV_IS_NOWHERE for example), which causes the following build
failure:
Fixes:
LD u-boot
/home/thomas/sh4aeb-linux-musl/bin/sh4aeb-linux-ld.bfd: cannot find common/env_embedded.o
We fix this by no longer adding the .ppcenv and .ppcenvr sections from
common/env_embedded.o into the .text section.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The SuperH architecture allows to be run in either little or big
endian mode. Some SuperH SoCs get the little vs. big endian decision
through mode pins sampled at reset, so if big endian has been choosen
by HW designers, it cannot be easily changed.
Therefore, it makes sense to allow building U-Boot for SuperH in big
endian mode. To allow this, the only change needed is to adjust the
OUTPUT_FORMAT() in the linker script.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We need the clock available very early, add the u-boot,dm-pre-reloc
DT property on those nodes, so they come up very in the process.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
i.MX 6 serial downloader is not necessarily booting via UART but can
also boot from USB. In fact only some i.MX chips have serial
downloader support via UART (e.g. 6UL/ULL and Vybrid) but all of
them have serial downloader support via USB. Use the more appropriate
BOOT_DEVICE_BOARD define which is used for ROM provided recovery
mechanisms in general.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Add the reserved boot mode used in the bmode command for i.MX 6UL
and 6ULL as introduced in commit 3fd9579085 ("imx: mx6ull: fix USB
bmode for i.MX 6UL and 6ULL").
Also replace BMODE_UART with BMODE_RESERVED, which is more appropriate.
Commit 96aac843b6 ("imx: Use IMX6_BMODE_* macros instead of numericals")
added macros for boot modes, in the process the reserved boot mode got
named BMODE_UART. We use the reserved boot mode in the bmode command to
let the boot ROM enter serial downloader recovery mode. But this is only
a side effect, the actual boot mode is reserved...
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
These options should not be exposed to other platforms.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Let's imply the 'pci' command to access the de facto interconnect
bus in an x86 system.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Some Intel FSP (like Braswell) does SPI lock-down during the call
to fsp_notify(INIT_PHASE_BOOT). But before SPI lock-down is done,
it's bootloader's responsibility to configure the SPI controller's
opcode registers properly otherwise SPI controller driver doesn't
know how to communicate with the SPI flash device.
This introduces a Kconfig option CONFIG_FSP_LOCKDOWN_SPI for such
FSPs. When it is on, U-Boot will configure the SPI opcode registers
before the lock-down.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Some files for i.MX do not yet have the SPDX ID to reference the correct
license.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Since commit 576e3cc700 ("usb: host: xhci-dwc3: Add dual role mode
support from DT"), warning is displayed if dr_mode is not specified.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit 82d075e79f.
Commit 82d075e79f ("ARM: uniphier: fix ROM boot mode for PH1-sLD3")
was a workaround for sLD3. Now the sLD3 SoC support has been removed.
Revert it to allow to simplify the init code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit bcc51c1512.
Commit bcc51c1512 ("ARM: uniphier: move lowlevel debug init code
after page table switch") was intended to support lowlevel debug for
sLD3. Now the sLD3 SoC support has been removed.
Revert it to allow to enable lowlevel debug earlier.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit f0776a5517 ("spl: dm: Kconfig: SPL_CLK depends on
SPL_DM"), the following warning is displayed:
$ make uniphier_v8_defconfig
warning: (ARCH_ZYNQ && ARCH_ZYNQMP && STM32F7 && CLK_UNIPHIER) selects
SPL_CLK which has unmet direct dependencies (CLK && SPL_DM)
While I am here, I am removing the prompt to make it user-unconfigurable
option so that "select CLK_UNIPHIER" can be omitted.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The description for eMMC/SDIO/SDMMC src is not correct,
update the CRU_CLKSEL11_CON value definition according to TRM.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The DRAM start address is not 0, so need to update the last bank size
as:
DRAM start addr + DRAM_SIZE - last bank start addr
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
fdtdec.h is included, but not used in rk3399-board-spl.c: remove the
'#include'-statement.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There are two same gmac node, remove one.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Sysam stmark2 board is a generic and fully (hw and sw) open board, with
a mcf54415 Coldfire CPU, 128MB of DDR2, 16MB of SPI flash and SD card
as non volatile memories, and a wifi module included on-board.
The board is actually used mainly for Coldfire custodian testing activity
related to the mcf5441x Coldfire family.
For further information please see: http://sysam.it/cff_stmark2.html
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
---
Changes in v2:
- remove CMD_REGINFO
- add board information in commit message
For certain boot types and sbf, for V4 cpu's, an early ddr/sdram init
is required. This patch moves this ddr/sdram early initalization
away from start.S (to be board related).
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Update the tx_delay and rx_delay to match the timing for
rk3399-firefly board to improve the stability of gmac data
transfer.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
All boards which use DM_MMC have now been converted to use DM_MMC_OPS.
Drop the option and good riddance.
Signed-off-by: Simon Glass <sjg@chromium.org>
The command handling in this driver is awful, esp. because the driver
depends on command numbers to determine whether this is APPCMD or not.
Also, handling of command RSP response types is totally wrong.
This patch at least plucks out some of the custom command encoding and
fixes the APPCMD handling. The RSP handling still needs work, yet that
might not be needed as it turns out the uniphier-sd.c driver is in much
better shape and supports the same IP, so we might be able to just drop
this driver in favor of the uniphier one.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
We are now using an env_ prefix for environment functions. Rename these
other functions as well, for consistency:
getenv_vlan()
getenv_bootm_size()
getenv_bootm_low()
getenv_bootm_mapsize()
env_get_default()
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
commonly used functions, for consistency. Also add function comments in
common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix build warning when CONFIG_IMX_RDC not defined in defconfig.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
As M4 is sourcing UART clk from OSC, to make UART work
when M4 is enabled, need to select OSC as clk parent,
24M OSC is enough for debug UART in uboot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
There is not LDO_SOC/PU/ARM/MMDC1 on i.MX6SLL, also no need to gate/ungate
all PFDs to make PFD working.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Under very rare timing circumstances, transitioning into streaming
mode might create a data corruption. Present on Two or more processors
or 1 core with ACP, all revisions. This erratum can be worked round
by setting bit[22] of the undocumented Diagnostic Control Register to 1.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The ARM errata 751472, 794072, 761320 only applied
to the following configuration:
This erratum affects configurations with either:
- One processor if the ACP is present
- Two or more processors
i.MX6 family does not have the ACP and thus only the MPCore system
will be impacted, which are the i.MX6DQ, i.MX6DL, and i.MX6QP.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Use the env_save() function directly now that there is only one
implementation of saveenv().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present we support multiple environment drivers but there is not way to
select between them at run time. Also settings related to the position and
size of the environment area are global (i.e. apply to all locations).
Until these limitations are removed we cannot really support more than one
environment location. Adjust the location to be a choice so that only one
can be selected. By default the environment is 'nowhere', meaning that the
environment exists only in memory and cannot be saved.
Also expand the help for the 'nowhere' option and move it to the top since
it is the default.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Move all of the imply logic to default X if Y so it works again]
Signed-off-by: Tom Rini <trini@konsulko.com>
About a quarter of the files in common/ relate to the environment. It
seems better to put these into their own subdirectory and remove the
prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
OLimex A64-OLinuXino is an open-source hardware board
using the Allwinner A64 SOC.
OLimex A64-OLinuXino has
- A64 Quad-core Cortex-A53 64bit
- 1GB or 2GB RAM DDR3L @ 672Mhz
- microSD slot and 4/8/16GB eMMC
- Debug TTL UART
- HDMI
- LCD
- IR receiver
- 5V DC power supply
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.
Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
A few years ago STM32F1 SoCs support has been added :
0144caf22c gpio: stm32: add stm32f1 support
2d18ef2364 ARMv7M: add STM32F1 support
But neither STM32F1 dedicated defconfig nor board was
associated to these commits.
Got confirmation from Tom Rini and Matt Porter to remove
all this code [1]
[1] http://u-boot.10912.n7.nabble.com/Remove-STM32F1-support-td301603.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
OMAP5432 did go into production with AVS class0 registers which were
mutually exclusive from AVS Class 1.5 registers.
Most OMAP5-uEVM boards use the pre-production Class1.5 which has
production efuse registers set to 0. However on production devices,
these are set to valid data.
scale_vcore logic is already smart enough to detect this and use the
"Nominal voltage" on devices that do not have efuse registers populated.
On a test production device populated as follows:
MPU OPP_NOM:
=> md.l 0x04A0021C4 1
4a0021c4: 03a003e9 ....
(0x3e9 = 1.01v) vs nom voltage of 1.06v
MPU OPP_HIGH:
=> md.l 0x04A0021C8 1
4a0021c8: 03400485 ..@.
MM OPP_NOM:
=> md.l 0x04A0021A4 1
4a0021a4: 038003d4 ....
(0x3d4 = 980mV) vs nom voltage of 1.025v
MM OPP_OD:
=> md.l 0x04A0021A8 1
4a0021a8: 03600403 ..`.
CORE OPP_NOM:
=> md.l 0x04A0021D8 1
4a0021d8: 000003cf ....
(0x3cf = 975mV) vs nom voltage of 1.040v
Since the efuse values are'nt currently used, we do not regress on
existing pre-production samples (they continue to use nominal voltage).
But on boards that do have production samples populated, we can leverage
the optimal voltages necessary for proper operation.
Tested on:
a) 720-2644-001 OMAP5UEVM with production sample.
b) 750-2628-222(A) UEVM5432G-02 with pre-production sample.
Data based on OMAP5432 Technical reference Manual SWPU282AF (May
2012-Revised Aug 2016)
NOTE: All collaterals on OMAP5432 silicon itself seems to have been
removed from ti.com, though EVM details are still available:
http://www.ti.com/tool/OMAP5432-EVM
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The if in the else branch is superfluous.
We can use a simple if.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
It does not make sense to check if info is NULL after
dereferencing it.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
For DEVICE_NON_SHARED the newly assigned value of attr
is overwritten due to a missing break.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
It does not make sense first to dereference c and then
to check if it is NULL.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
mmc using 150000000 as max-frequency like what rk3288 sets.
This can speed up the mmc read/write, the actual mmc clock is:
Before this patch: 37.125M
After this patch: 49.5M
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
add node for sdmmc in dts and rk3229-evb.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Disable the ddr secure region setting in SPL and the ddr memory
becomes non-secure, every one can access it. the trust firmware
like OPTEE should have the correct setting for it after SPL if
there is one.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
It should be '<<' instead of '<' for _MASK definition, fix it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the new way of doing things (i.e. the hierarchical selection of
SPL_LDSCRIPT via Kconfig) in place, this moves the SPL_LDSCRIPT setting
for the RK3368 from defconfig back into Kconfig.
With this done, there should be no lingering cases of SPL_LDSCRIPT
outside of Kconfig files.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With SPL_LDSCRIPT moved to Kconfig (and this being a 'string' config
node), all the lingering definitions in header files will cause
warnings/errors due to the redefinition of the configuration item.
As we don't want to pollute the defconfig files (and values should
usually be identical for entire architectures), the defaults are moved
into Kconfig. Kconfig will always pick the first default that
matches, so please keep these values at the end of each file (to allow
any board-specific Kconfig, which will be included earlier) to
override with an unconditional default setting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the changes to split SPL/TPL for the RK3368, I apparently missed
some needed adjustments to the RK3188 Kconfig and rock_defconfig.
This fixes build-issues for the rock board after applying the RK3368
enablement (and SPL/TPL) set that resulted from TPL_SERIAL_SUPPORT,
TPL_ROCKCHIP_BACK_TO_BROM and TPL_TINY_MEMSET being separate symbols
now.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Device drivers like debug serial, dmc should be enabled before
relocation, so add u-boot.dtsi files to contain devices that
should be marked as dm-pre-reloc.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using DM timers w/ the timer0 block within the RK3368, we no
longer depend on the ARMv8 generic timer counting. This allows us to
drop the secure timer initialisation from the TPL and SPL stages.
The secure timer will later be set up by ATF, which starts the ARMv8
generic timer. Thus, there will be a dependency from Linux to the ATF
through the ARMv8 generic timer... this seems reasonable, as Linux
will require the ATF (and PSCI) to start up the secondary cores anyway
(in other words: we don't add any new dependencies).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To use it with the DM timer driver in SPL and TPL, timer0 needs to be
marked as pre-reloc.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To fully support DM timer in SPL and TPL, we need a few things cleaned
up and normalised:
- inclusion of the uclass and drivers should be an all-or-nothing
decision for each stage and under control of $(SPL_TPL_)TIMER
instead of having the two-level configuration with TIMER and
$(SPL_TPL_)TIMER_SUPPORT
- when $(SPL_TPL_)TIMER is enabled, the ARMv8 generic timer code can
not be compiled in
This normalises configuration to $(SPL_TPL_)TIMER and moves the config
options to drivers/timer/Kconfig (and cleans up the collateral damage
to some defconfigs that had SPL_TIMER_SUPPORT enabled).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We can finally drop TPL_STACK, TPL_TEXT_BASE and TPL_MAX_SIZE off the
whitelist (this time it's really happening!) and migrate the setting
(only used on the RK3368-uQ7 so far) into Kconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3368 needs to have a different base-address and stack-pointer
for its TPL stage. Now that we want to do this via Kconfig, we need
to tick the appropriate 'TPL_NEEDS_...' boxes.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that TPL_STACK has been moved off the whitelist (ok, I'm lying:
the 'moving off the whitelist' part comes in once moveconfig
runs... which will be a few commits down the line) and added to
Kconfig, we need to test CONFIG_TPL_NEEDS_SEPARATE_STACK to see
whether the value from TPL_STACK should be used or whether we try to
inherit whatever SPL uses.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3368-uQ7 (codenamed 'Lion') is a micro-Qseven (40mm x 70mm,
MXM-230 edge connector compatible with the Qseven specification)
form-factor system-on-module based on the octo-core Rockchip RK3368.
It is designed, supported and manufactured by Theobroma Systems.
It provides the following features:
- 8x Cortex-A53 (in 2 clusters of 4 cores each)
- (on-module) up to 4GB of DDR3 memory
- (on-module) SPI-NOR flash
- (on-module) eMMC
- Gigabit Ethernet (with an on-module KSZ9031 PHY)
- USB
- HDMI
- MIPI-DSI/single-channel LVDS (muxed on the 'LVDS-A' pin-group)
- various 'slow' interfaces (e.g. UART, SPI, I2C, I2S, ...)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With SPL and TPL support for the RK3368 in place, mark SPL and TPL as
supported from Kconfig for the RK3368. As this is primarily tested on
the RK3368-uQ7, we'll leave it to board's individual defconfig to
enable.
Also enable DEBUG_UART_BOARD_INIT for the RK3368, so we get output
during the early boot-up, as we turn on TPL and SPL.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds SPL support for the RK3368 (assuming that our TPL stage has
initialised DRAM and set up the memory firewall).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to reuse the support for the u-boot,spl-boot-order property
from the rk3399, we split it into a reusable module that can be
included by the SPL code for any of our boards.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds the TPL support for the RK3368, including the u-boot-tpl.lds.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For full SPL support, including DRAM initialisation, we need a few
nodes from the DTS: this commit adds the DMC (DRAM controller) node,
the service_msch (memory scheduler) node and marks GRF, PMUGRF and CRU
as 'u-boot,dm-pre-reloc'. In addition to this, we also include the
dt-binding for the DMC to allow DTS files including this DTSI to refer
to the symbolic constants for the DDR3 bin and for the
memory-schedule.
Note that the DMC contains both the memory regions for the
(Designware) protocol controller as well as the DDR PHY.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a DRAM controller driver for the RK3368 and places it in
drivers/ram/rockchip (where the other DM-enabled DRAM controller
drivers for rockchip devices should also be moved eventually).
At this stage, only the following feature-set is supported:
- DDR3
- 32-bit configuration (i.e. fully populated)
- dual-rank (i.e. no auto-detection of ranks)
- DDR3-1600K speed-bin
This driver expects to run from a TPL stage that will later return to
the RK3368 BROM. It communicates with later stages through the
os_reg2 in the pmugrf (i.e. using the same mechanism as Rockchip's DDR
init code).
Unlike other DMC drivers for RK32xx and RK33xx parts, the required
timings are calculated within the driver based on a target frequency
and a DDR3 speed-bin (only the DDR3-1600K speed-bin is support at this
time).
The RK3368 also has the DDRC0_CON0 (DDR ch. 0, control-register 0)
register for controlling the operation of its (single-channel) DRAM
controller in the GRF block. This provides for selecting DDR3, mobile
DDR modes, and control low-power operation.
As part of this change, DDRC0_CON0 is also added to the GRF structure
definition (at offset 0x600).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Handling TPL and SPL in the Makefile for mach-rockchip was based on
nested if checks and/or if-else-if paths. This can be simplified and
made more readable by using $(SPL_TPL_) and by introducing
intermediate variables for the aggregation of SPL and TPL features.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GMAC in the RK3368 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3368-specific logic necessary to reuse this driver.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To enable the GMAC on the RK3368, we need to set up the clocking
appropriately to generate a tx_clk for the MAC.
This adds an implementation that implements the use of the <&ext_gmac>
clock (i.e. an external 125MHz clock for RGMII provided by the PHY).
This is the clock setup used by the boards currently supported by
U-Boot (i.e. Geekbox, Sheep and RK3368-uQ7).
This includes the change from commit
- rockchip: clk: rk3368: define GMAC_MUX_SEL_EXTCLK
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The original clock support for MMC/SD cards on the RK3368 suffered
from a tendency to select a divider less-or-equal to the the one
giving the requested clock-rate: this can lead to higher-than-expected
(or rather: higher than supported) clock rates for the MMC/SD
communiction.
This change rewrites the MMC/SD clock generation to:
* always generate a clock less-than-or-equal to the requested clock
* support reparenting among the CPLL, GPLL and OSC24M parents to
generate the highest clock that does not exceed the requested rate
In addition to this, the Linux DTS uses HCLK_MMC/HCLK_SDMMC instead of
SCLK_MMC/SCLK_SDMMC: to match this (and to ensure that clock setup
always works), we adjust the driver appropriately.
This includes the changes from:
- rockchip: clk: rk3368: convert MMC_PLL_SEL_* definitions to shifted-value form
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On he RK3368, we need to temporarily disable security on the DMA
engines during TPL and SPL to allow the MMC host to DMA into DRAM. To
do so, we need to reset the two DMA engines, which in turn requires
the DMA1_SRST_REQ and DMA2_SRST_REQ constants to refer to the
appropriate bits in the CRU.
As the ATF correctly initialises security (and only leaves EL3 after
doing so), this can not pose a security issue.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no real reason to keep the bit-definitions for the IOMUX in
the grf header file (which defines the register layout of the GRF block):
these should only be used by our pinctrl driver (with the possible
exception of early debug-init code in TPL/SPL).
This moves the relevant definitions from the grf_rk3368.h header
into the pinctrl driver pinctrl_rk3368.c.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We will to drop device security temporarily (until the ATF initialises
it fully) from the TPL/SPL stage: this requires access to some
registers in the SGRF.
This adds the sgrf node to the rk3368.dtsi, so we can then bind a
syscon device onto it and access its memory ranges.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3368 GRF header was still defines with a shifted-mask but with
non-shifted function selectors for the IOMUX defines. As the RK3368
support is still fresh enough to allow a quick change, we do this now
before having more code use this.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
In TPL we will need to configure security in the SGRF of the RK3368.
This change adds support for the SGRF as a syscon device, so we can
retrieve its address range through the syscon API in TPL (and can
avoid having to hard-code the address).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3368 has both a limited TPL size (just 0x7000 bytes) and the
added challenge of booting in AArch64, which increases the code size
for TPL (particularily when using the LP64 programming model). For
this reason we expect the RK3368 to always use OF_PLATDATA for its
TPL stage.
This change adds support for the MSCH, PMUGRF and GRF register regions
in syscon, which are necessary for initialising the RK3368's DRAM
controller.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
