Commit Graph

34108 Commits

Author SHA1 Message Date
Shaohui Xie
f8642ba6dd net: phy: added aquantia PHY AQR405 support
The phy can share driver with other aquantia PHYs, so we only
add PHY ID.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:13 -08:00
Prabhakar Kushwaha
b401736463 armv8: ls2085a: Add workaround of errata A009635
If the core runs at higher than x3 speed of the platform, there is
possiblity about sev instruction to getting missed by other cores.
This is because of SoC Run Control block may not able to sample
the EVENTI(Sev) signals.

Configure Run Control and EPU to periodically send out EVENTI signals to
wake up A57 cores.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:12 -08:00
Prabhakar Kushwaha
5380335e66 board/ls2080qds: Fix typo in README for QSGMII riser card
DPMACx to PHY mapping for SGMII is mentioned as QSGMII.

So fix typo in README for QSGMII rise card.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Change from ls2085aqds to ls2080aqds]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:12 -08:00
Alison Wang
99fe454171 arm: ls102xa: Update fdt_high and initrd_high for LS1021AQDS board
As 3G/1G user/kernel memory split is used on LS1021A, the Linux kernel
fails to access the device tree blob on boot. The reason is that u-boot
relocates the device tree blob into high memory when booting the kernel
and the kernel is unable to access the blob.

To avoid this issue, fdt_high is set to the value of 0xffffffff. The
device tree blob will not get relocated and is still in low memory to
make it accessible to the kernel.

For the same reason, initrd_high is set to the value of 0xffffffff too.

This patch is to update fdt_high and initrd_high for LS1021AQDS board.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:12 -08:00
York Sun
1f6236f06b armv8: fsl-layerscape: Fix "cpu release" command
When one core is released, other cores may not have valid entry
address. Those cores are trapped by "wfe" and wait for further
instruction. When their address is set, they need to be kicked
off by "sev".

Signed-off-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:12 -08:00
York Sun
da305b9f57 drivers/ddr/fsl: Fix typo in BIST test for DDR4
BIST test code has a typo, resulting the binding registers not
maintained as expected. This typo results BIST runs twice on
the covered memory.

Signed-off-by: York Sun <yorksun@freescale.com>
Reported-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2015-11-30 09:11:12 -08:00
Alison Wang
d764129d30 armv8/layerscape: Update MMU table with execute-never bits
For most device addresses excution shouldn't be allowed. Revise
the MMU table to enforce execute-never bits. OCRAM, DDR and IFC
are allowed for excution.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reported-by: Zhichun Hua <zhichun.hua@freescale.com>
2015-11-30 09:11:11 -08:00
York Sun
61bd2f75f5 drivers/ddr/fsl: Enable detection of one DDR controller operation for LSCH3
Freescale LSCH3 platforms use two DDR controlers interleaving mode out of
reset. It can be configured to disable one controller. To support this
operation, the driver needs to detect and skip the disabled controller.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:11 -08:00
Gong Qianyu
7023100971 armv8/ls1043ardb: add USB support
Add support for the third USB controller for LS1043A.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:11 -08:00
Gong Qianyu
28752cf83b armv8/ls1043ardb: add DSPI support
Use the U-Boot Driver Model. Just enable Freescale DSPI driver
and set DSPI related parameters in dts file.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:11 -08:00
Gong Qianyu
630532f51f armv8/ls1043aqds: dts: add dtb support
Reuse the dts files from ls1043a linux kernel.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:11 -08:00
Shaohui Xie
02b5d2ed86 armv8/ls1043aqds: add LS1043AQDS board support
LS1043AQDS Specification:
-------------------------
Memory subsystem:
 * 2GByte DDR4 DIMM
 * 128 Mbyte NOR flash single-chip memory
 * 512 Mbyte NAND flash
 * 16 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card

Ethernet:
 * Two RGMII ports
 * XFI 10G port
 * SGMII
 * QSGMII with 4x 1G ports

PCIe: supports Gen 1 and Gen 2

SATA 3.0: one SATA 3.0 port

USB 3.0: two micro AB connector and one type A connector

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
[York Sun: Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:10 -08:00
Gong Qianyu
e1cecb4d42 armv8/ls1043ardb: dts: add dtb support
Reuse dts files from ls1043a linux kernel. Some parts in dts files
may not be needed by U-Boot.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:10 -08:00
Gong Qianyu
18a0d8eb46 armv8/fsl-layerscape: Remove reference to gdata
The global_data pointer (gd) has been set earlier in crt0_64.S.
So there's no need to assign it again. Remove gdata since it is going
away in U-Boot.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:10 -08:00
Mingkai Hu
af523a0d56 pci/layerscape: add support for LS1043A PCIe LUT register access
The endian and base address of PEX LUT register region is different
between Chassis 2 and Chassis 3, so move the base address definition
to chassis specific header file and add pex_lut_* functions to access
LUT register.

Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:10 -08:00
Prabhakar Kushwaha
06b5301043 armv8: ls2085a: Add support of LS2085A SoC
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.

Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
           Dropped #ifdef in cpu.h
           Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:10:47 -08:00
Prabhakar Kushwaha
449372148f armv8: LS2080A: Rename LS2085A to reflect LS2080A
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)

Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:04 -08:00
Prabhakar Kushwaha
14480454c7 driver: net: ldpaa: Fix Rx buffer alignment
MC 0.7.1.2 enforces limitation i.e.: "Packets may be corrupted
in several combinations of buffer size and frame offsets.
Workaround: Use buffers that are of size that is a multiple of 256, and
frame offset that is a multiple of 256"

Updating the DPNI Eth driver to comply with the restriction.

Signed-off-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:03 -08:00
Prabhakar Kushwaha
5038d3e5f2 driver: net: ldpaa: Add debug information
Add following debug information in the driver
 - Get various DPNI counter values
 - Get link status of DPNI objects
 - Get information of both ends of connection (DPMAC - DPNI)

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:03 -08:00
Prabhakar Kushwaha
c919ab9ee5 driver: net: ldpaa: Use DPMAC as net device
As per current implementation of DPAA2 ethernet driver DPNI is used as
net device. DPNI is tangible objects can be multiple connected to same physical lane.

Use DPMAC as net device where it represents physical lane.
Below modification done in driver
 - Use global DPNI object
 - Connect DPMAC to DPNI
 - Create and destroy DPMAC

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:03 -08:00
Prabhakar Kushwaha
1730a17db9 driver: net: fsl-mc: Create DPAA2 object at run-time
Freescale's DPAA2 ethernet driver depends upon the static DPL for the
DPRC, DPNI, DPBP, DPIO objects.

Instead of static objects, Create DPNI, DPBP, DPIO objects at run-time.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:03 -08:00
Prabhakar Kushwaha
fb4a87a737 driver: net: fsl-mc: Add DPAA2 commands to manage MC
Management complex Firmware, DPL and DPC are depolyed during u-boot boot
sequence.

Add new DPAA2 commands to manage Management Complex (MC) i.e. start mc, aiop
and apply DPL from u-boot command prompt.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:03 -08:00
Prabhakar Kushwaha
553d2751c1 driver: net: fsl-mc: Increase MC command timeout
dpni_create API take takes more time as comapred to existing supported
APIs of MC Flib.
So increase MC command timeout.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:02 -08:00
Prabhakar Kushwaha
f9127a046d driver: ldpaa: Add api to return linked PHY ID of DPMAC
DPMAC represents physical line on the board. This physical
line eventually asscociate with on-board PHY.

So Add an api to return linked PHY ID of DPMAC object.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:02 -08:00
Prabhakar Kushwaha
25af413740 armv8: ls2085aqds: Print function name during SerDes error
Print function name along with SerDes Protocol during SerDes Protocol
not supported error.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:02 -08:00
Prabhakar Kushwaha
872d48a777 driver: net: fsl-mc: Add APIs for DPMAC objects in FLIB
DPMAC object of Management complex controls Physical MAC and MDIO controller.
It provides APIs for MDIO and link state updates. It also provides APIs for
PHY/link configuration.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:02 -08:00
Prabhakar Kushwaha
1ebbe4fcf7 driver: net: fsl-mc: Add create, destroy APIs in flibs
Current Management Complex Flibs does not support APIs for adding and
destroying the objects.

Add APIs to create and destroy objects for DPBP, DPIO, DPNI and DPRC.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:02 -08:00
Prabhakar Kushwaha
99e904c1f0 armv8: lsch3: Fix lane protocol parsing logic
Current implementation only consider SGMIIs for dpmac initialization.
XFI serdes protocols also uses dpmac.

Also, fix lane protocol parsing logic to consider both XFIs and SGMIIs.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:02 -08:00
Alison Wang
a1399534f1 arm: ls1021a: Ensure Generic Timer disabled before jumping into the OS
This patch addresses a problem mentioned recently on this mailing list:
[1].

In that posting a LS1021 based system was locking up at about 5 minutes
after boot,but the problem was mysteriously related to the toolchain
used for building u-boot.Debugging the problem reveals a stuck
interrupt 29 on the GIC.

It appears Freescale's LS1021 support in u-boot erroneously sets the
64-bit ARM generic PL1 physical time CompareValue register to all-ones
with a 32-bit value.This causes the timer compare to fire 344 seconds
after u-boot configures it.Depending on how fast u-boot gets the
kernel booted,this amounts to about 5-minutes of Linux uptime before
locking up.

Apparently the bug is masked by some toolchains. Perhaps this is
explained by default compiler options, word sizes, or binutils versions.

To fix the above issue, the generic physical timer is disabled
before jumping to the OS.

[1]
https://lists.yoctoproject.org/pipermail/meta-freescale/2015-June/014400.html

Signed-off-by: Chris Kilgour <techie@whiterocker.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:01 -08:00
Alison Wang
2b714cfad4 arm: ls1021a: Ensure LS1021 ARM Generic Timer CompareValue Set 64-bit
This patch addresses a problem mentioned recently on this mailing list:
[1].

In that posting a LS1021 based system was locking up at about 5 minutes
after boot, but the problem was mysteriously related to the toolchain
used for building u-boot.  Debugging the problem reveals a stuck
interrupt 29 on the GIC.

It appears Freescale's LS1021 support in u-boot erroneously sets the
64-bit ARM generic PL1 physical time CompareValue register to all-ones
with a 32-bit value.  This causes the timer compare to fire 344 seconds
after u-boot configures it.  Depending on how fast u-boot gets the
kernel booted, this amounts to about 5-minutes of Linux uptime before
locking up.

Apparently the bug is masked by some toolchains.  Perhaps this is
explained by default compiler options, word sizes, or binutils versions.
At any rate this patch makes the manipulation explicitly 64-bit which
alleviates the issue.

[1]
https://lists.yoctoproject.org/pipermail/meta-freescale/2015-June/014400.html

Signed-off-by: Chris Kilgour <techie@whiterocker.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:01 -08:00
Tom Rini
fa8883a1e3 Merge branch 'master' of git://git.denx.de/u-boot-i2c 2015-11-27 08:41:03 -05:00
Stefan Roese
a06728c839 i2c: Fix the comment to match the function described
Use the correct function name in the function description.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
2015-11-27 05:54:21 +01:00
Stefan Roese
01ce961b15 arm: spear: x600: Enable tiny-printf
Enabling the new tiny-printf function makes the SPL image fit again in
the 8KiB restricted area.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
2015-11-25 10:06:45 -05:00
Bin Meng
68d5342017 sf: Move SPI flash drivers to defconfig
There are already Kconfig options for SPI flash drivers, but we
have not moved them from config.h to defconfig files. This commit
does this in a batch.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-11-25 10:06:05 -05:00
Bin Meng
e5d5d4474a spi: Move SPI drivers to defconfig
There are already Kconfig options for SPI drivers, but we
have not moved them from config.h to defconfig files. This
commit does this in a batch.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-11-25 10:05:28 -05:00
Vignesh R
71cbed31f4 am33xx: Remove serial_init in s_init for QSPI/NOR XIP boot
serial_init() reads global_data, since global_data is not yet
initialized, this can cause unwanted behaviour leading to QSPI XIP boot
hang. Also, since serial_init() is anyways called later from
boar_init_f(), it does not make sense to do the same in s_init().

Tested on AM437x IDK EVM with QSPI XIP boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-11-23 11:01:53 -05:00
Thomas Fitzsimmons
54d68e9333 fs: ext4: Prevent infinite loop in ext4fs_iterate_dir
If the ext3 journal gets out of sync with what is written on disk, for
example because of an unexpected power cut, ext4fs_read_file can
return an all-zero directory entry.  In that case, ext4fs_iterate_dir
would infinite loop.

This patch detects when a directory entry's direntlen member is 0 and
returns a failure status, which breaks out of the infinite loop.  As a
result, U-Boot will not find files that may subsequently be recovered
when the journal is replayed.

This is better behaviour than hanging in an infinite loop, but as a
further improvement maybe U-Boot could interpret the ext3 journal and
actually find the unsynced entries.

Signed-off-by: Thomas Fitzsimmons <fitzsim@cisco.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2015-11-23 11:01:52 -05:00
Marcel Ziswiler
b4bd655493 pci: fix address range check in __pci_hose_phys_to_bus()
The address range check may overflow if the memory region is located at
the top of the 32-bit address space. This can e.g. be seen on TK1 if
using the E1000 gigabit Ethernet driver where start and size are both
0x80000000 leading to the following messages:

Apalis TK1 # tftpboot $loadaddr test_file
Using e1000#0 device
TFTP from server 192.168.10.1; our IP address is 192.168.10.2
Filename 'test_file'.
Load address: 0x80408000
Loading: pci_hose_phys_to_bus: invalid physical address

This patch fixes this by changing the order of the addition vs.
subtraction in the range check just like already done in
__pci_hose_bus_to_phys().

Reported-by: Ivan Mercier <ivan.mercier@nexvision.fr>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-11-23 11:01:52 -05:00
Patrick Delaunay
cfdaf4caa2 part:efi: add bootable parameter in gpt command
The optional parameter bootable is added in gpt command to set the
partition attribute flag "Legacy BIOS bootable"

This flag is used in extlinux and so in with distro to select
the boot partition where is located the configuration file
(please check out doc/README.distro for details).

With this parameter, U-Boot can be used to create the boot partition
needed for device using distro.

example of use:

setenv partitions "name=u-boot,size=60MiB;name=boot,size=60Mib,bootable;\
                   name=rootfs,size=0"

> gpt write mmc 0 $partitions

> part list mmc 0

Partition Map for MMC device 0  --   Partition Type: EFI

Part	Start LBA	End LBA		Name
	Attributes
	Type GUID
	Partition GUID
  1	0x00000022	0x0001e021	"u-boot"
	attrs:	0x0000000000000000
	type:	ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
	guid:	cceb0b18-39cb-d547-9db7-03b405fa77d4
  2	0x0001e022	0x0003c021	"boot"
	attrs:	0x0000000000000004
	type:	ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
	guid:	d4981a2b-0478-544e-9607-7fd3c651068d
  3	0x0003c022	0x003a9fde	"rootfs"
	attrs:	0x0000000000000000
	type:	ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
	guid:	6d6c9a36-e919-264d-a9ee-bd00379686c7

> part list mmc 0 -bootable devplist

> printenv devplist

devplist=2

Then the distro scripts will search extlinux in partition 2
and not in the first partition.

Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2015-11-23 11:01:52 -05:00
Lukasz Majewski
bbb9ffac60 gpt: command: Extend gpt command to support GPT table verification
This commit adds support for "gpt verify" command, which verifies
correctness of on-board stored GPT partition table.
As the optional parameter one can provide '$partitons' environment variable
to check if partition data (size, offset, name) is correct.

This command should be regarded as complementary one to "gpt restore".

Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Przemyslaw Marczak <p.marczak@samsung.com>
2015-11-23 11:01:51 -05:00
Lukasz Majewski
cef68bf904 gpt: part: Definition and declaration of GPT verification functions
This commit provides definition and declaration of GPT verification
functions - namely gpt_verify_headers() and gpt_verify_partitions().
The former is used to only check CRC32 of GPT's header and PTEs.
The latter examines each partition entry and compare attributes such as:
name, start offset and size with ones provided at '$partitions' env
variable.

Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Przemyslaw Marczak <p.marczak@samsung.com>
2015-11-23 11:01:50 -05:00
Lukasz Majewski
74f889b039 gpt: doc: Update gpt command's help description
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-11-23 11:01:46 -05:00
Lukasz Majewski
dd445879f7 gpt: doc: README: Update README entry for gpt verify extension
./doc/README.gpt entry has been updated to explain usage of "gpt verify"
command.

Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-11-23 10:56:09 -05:00
Lukasz Majewski
5af9dd3739 gpt: command: Remove duplicated check for empty partition description
Exactly the same check is performed in set_gpt_info() function executed
just after this check.

Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-11-23 10:56:08 -05:00
Stefan Roese
a5ecdd08fd lib/tiny-printf.c: Support numbers bigger than 0xffff and misc updates
With this patch now, the tiny printf() function also supports numbers
bigger than 0xffff. Additionally the code is simplified a bit and
some static variables are moved to function parameters. Also the
upper case hex variable output support is removed, as its not really
needed in this simple printf version. And removing it reduces the
complexity and the code size again a bit.

Here the new numbers, again on the db-mv784mp-gp (Armada XP):

Without this patch:
  56542   18536    1956   77034   12cea ./spl/u-boot-spl

With this patch:
  56446   18536    1936   76918   12c76 ./spl/u-boot-spl

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2015-11-23 10:56:08 -05:00
Stefan Roese
7d9cde1031 lib/tiny-printf.c: Add tiny printf function for space limited environments
This patch adds a small printf() version that supports all basic formats.
Its intented to be used in U-Boot SPL versions on platforms with very
limited internal RAM sizes.

To enable it, just define CONFIG_USE_TINY_PRINTF in your defconfig. This
will result in the SPL using this tiny function and the main U-Boot
still using the full-blown printf() function.

This code was copied from:
http://www.sparetimelabs.com/printfrevisited
With mostly only coding style related changes so that its checkpatch
clean.

The size reduction is about 2.5KiB. Here a comparison for the db-mv784mp-gp
(Marvell AXP) SPL:

Without this patch:
  58963   18536    1928   79427   13643 ./spl/u-boot-spl

With this patch:
  56542   18536    1956   77034   12cea ./spl/u-boot-spl

Note:
To make it possible to compile tiny-printf.c instead of vsprintf.c when
CONFIG_USE_TINY_PRINTF is defined, the functions printf() and vprintf() are
moved from common/console.c into vsprintf.c in this patch.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2015-11-23 10:56:07 -05:00
Stefan Roese
ddf7355a73 common/console.c: Small coding style cleanup
Change some comments to match the U-Boot coding style rules.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
2015-11-23 10:56:07 -05:00
Stefan Roese
dd5577703b common/console.c: Drop sandbox special-case console code
As done in commit da229e4e [sandbox: Drop special-case sandbox console code],
this patch drops the sandbox special-case code in vprintf() that was
missed by Simon at that time.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
2015-11-23 10:56:06 -05:00
Heiko Schocher
f300dccde4 i2c, avr32: fix compiler warning "input is not relaxable"
compiling U-Boot for avr32 boards shows since
commit 3d1957f0ea "dm: i2c: Add support for multiplexed I2C buses"
this warning:

Building current source for 4 boards (4 threads, 8 jobs per thread)
     avr32:  +   atstk1002
+(atstk1002) drivers/i2c/built-in.o: warning: input is not relaxable
     avr32:  +   grasshopper
+(grasshopper) drivers/i2c/built-in.o: warning: input is not relaxable
     avr32:  +   atngw100
+(atngw100) drivers/i2c/built-in.o: warning: input is not relaxable
     avr32:  +   atngw100mkii
+(atngw100mkii) drivers/i2c/built-in.o: warning: input is not relaxable
    0    4    0 /4      0:00:16  : atngw100mkii

Fix it.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Roger Meier <r.meier@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-11-23 14:47:48 +01:00
Tom Rini
d018cd20b3 sunxi: Update new defconfigs
After introduction of CONFIG_SYS_NS16550 these defconfig files were
added and need to be updated.

Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-22 10:46:25 -05:00