In some circumstances, reset_timer_masked() was called be timer_init() in
order to perform architecture specific timer initialisation. In such
cases, the required code in reset_timer_masked() has been moved into
timer_init()
* 'master' of git://git.denx.de/u-boot-mmc:
mmc: rescan fails on empty slot
AT91:mmc:fix multiple read/write error
mmc: Access mode validation for eMMC cards > 2 GiB
mmc: sh_mmcif: add support for Renesas MMCIF
mmc: fix the condition for MMC version 4
MMC: add marvell sdhci driver
MMC: add sdhci generic framework
MMC: add erase function to both mmc and sd
MMC: unify mmc read and write operation
mmc: Tegra2: Enable SD/MMC driver for Seaboard and Harmony
mmc: Tegra2: SD/MMC driver for Seaboard - eMMC on SDMMC4, SDIO on SDMMC3
This check was broken. r3 does not contain the silicon revision anymore, so
we need to reload it. Also, this errata only applies to i.MX51.
Signed-off-by: David Jander <david@protonic.nl>
Acked-by: Stefano Babic <sbabic@denx.de>
Checkpatch.pl complains about the volatile qualifier in calls to
get_ram_size(). Remove this qualifier in the prototype and in the
calls where it is useless, and leave it only in the function body
where it is needed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
cpu_init_crit can be skipped, but the code is still enabled requiring a
platform to supply lowlevel_init.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Albert ARIBAUD <albert.aribaud@free.fr>
CONFIG_MACH_TYPE is used to set the machine type number in the
common arm code instead of setting it in the board code.
Boards with dynamically discoverable machine types can still set the
machine type number in the board code.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
On i.MX27, the asm-offsets.h file is not yet generated as it should be.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
On i.MX5, the asm-offsets.h file is not yet generated as it should be.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
zmx25 is a board based on imx25 SoC, 64 Megs of LPDDR, 32 Megs of NOR flash, an
optional NAND flash.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Offsets to registers may be needed in asm code. This patch adds automated
generation of these offsets form C structures.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Adding support for USB host on imx25 using the internal PHY. Changing the name
of base address define for imx31 to get some unification.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
mx27_uart_init_pins does the IOMUX setting for UART1 port.
Change the function name to make the UART port number explicit.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
asm-offsets.h should be auto generated. This patch adds two rules to rules.mk
which makes this possible and removes the rules on imx35.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Some boards e.g. keymile arm boards have CONFIG_CMD_I2C switched on
but they use soft i2c on kirkwood. So don't switch CONFIG_I2C_MVTWSI
on in this case.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
* Fix compiler error for cpu at91sam9, if lowlevel init is enabled
* use correct ATMEL_ name scheme to define ATMEL_BASE_SDRAMC
Signed-off-by: Jens Scharsig
This is a copy of arm926ejs/at91 api for perpherial initialisation.
At the moment we just need the usart part of the api.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch enables the new clock features from arm920t/at91/clock.c. This
is an required step to get at91rm9200_usart replaced by atmel_usart driver.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Jens Scharsig <js_at_ng@scharsoft.de>
Cc: Eric Bénard <eric@eukrea.com>
This patch adds an copy of arm926ejs/at91/clock.c to arm920t/at91. The
arm926ejs specialities are removed from arm920t version and vice versa.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch sets the ATMEL_PMX_AA_TXD2 to the correct value.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
CC: Jens Scharsig <js_at_ng@scharsoft.de>
CC: eric@eukrea.com
Acked-by: Eric Bénard <eric@eukrea.com>
As implemented now the timer used to implement __udelay counts
to 0xffffffff and then gets stuck there because the the programmed
reload value is 0xffffffff. This value is not only wrong but
illegal according to the reference manual.
One can reproduce the bug by leaving a board at the u-boot prompt
for sometime then issuing a sleep command. The sleep will hang
forever.
The timer is a count up timer that reloads as it rolls over
from 0xffffffff so the correct load value is 0.
Change TIMER_LOAD_VAL from 0xffffffff to 0 and introduce
a new constant called TIMER_OVERFLOW_VAL set to 0xffffffff.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
PL310 is the L2$ controller from ARM used in many SoCs
including the Cortex-A9 based OMAP4430
Add support for some of the key PL310 operations
- Invalidate all
- Invalidate range
- Flush(clean & invalidate) all
- Flush range
Signed-off-by: Aneesh V <aneesh@ti.com>
1. make sure that page table setup is not done multiple times
2. flush_dcache_all() is more appropriate while disabling cache
than a range flush on the entire memory(flush_cache())
Provide a default implementation for flush_dcache_all()
for backward compatibility and to avoid build issues.
Signed-off-by: Aneesh V <aneesh@ti.com>
- Enable I-cache on bootup
- Enable MMU and D-cache immediately after relocation
- Do necessary initialization before enabling d-cache and MMU
- Changes to cleanup_before_linux()
- Make changes according to the new framework
Signed-off-by: Aneesh V <aneesh@ti.com>
Replace the cache related CONFIG flags with more meaningful
names. Following are the changes:
CONFIG_L2_OFF -> CONFIG_SYS_L2CACHE_OFF
CONFIG_SYS_NO_ICACHE -> CONFIG_SYS_ICACHE_OFF
CONFIG_SYS_NO_DCACHE -> CONFIG_SYS_DCACHE_OFF
Signed-off-by: Aneesh V <aneesh@ti.com>
V2:
* Changed CONFIG_L2_OFF -> CONFIG_SYS_NO_L2CACHE
V4:
* Changed all three flags to the final names suggested as above
and accordingly changed the commit message
- Add a framework for layered cache maintenance
- separate out SOC specific outer cache maintenance from
maintenance of caches known to CPU
- Add generic ARMv7 cache maintenance operations that affect all
caches known to ARMv7 CPUs. For instance in Cortex-A8 these
opertions will affect both L1 and L2 caches. In Cortex-A9
these will affect only L1 cache
- D-cache operations supported:
- Invalidate entire D-cache
- Invalidate D-cache range
- Flush(clean & invalidate) entire D-cache
- Flush D-cache range
- I-cache operations supported:
- Invalidate entire I-cache
- Add maintenance functions for TLB, branch predictor array etc.
- Enable -march=armv7-a so that armv7 assembly instructions can be
used
Signed-off-by: Aneesh V <aneesh@ti.com>
* 'master' of git://git.denx.de/u-boot-arm:
run arm_pci_init after relocation
IXP42x PCI rewrite
update/fix PDNB3 board
update/fix IXDP425 / IXDPG425 boards
add dvlhost (dLAN 200 AV Wireless G) board
IXP NPE: add support for fixed-speed MII ports
update/fix AcTux4 board
update/fix AcTux3 board
update/fix AcTux2 board
update/fix AcTux1 board
use -ffunction-sections / --gc-sections on IXP42x
support CONFIG_SYS_LDSCRIPT on ARM
fix "depend" target in npe directory
Fix IXP code to work after relocation was added
trigger hardware watchdog in IXP42x serial driver
add support for IXP42x Rev. B1 and newer
add XScale sub architecture (IXP/PXA) to maintainer list
Conflicts:
arch/arm/lib/board.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
clean up IXP PCI handling: get rid of IXP-private bus scan, BAR assign etc.
code and use u-boot's PCI infrastructure instead. Move board-specific PCI
setup code (clock/reset) to board directory.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
