During very early boot-ROM execution the pinmux
configuration isi in Hi-Z state. If pull-up is enabled
on GPIO pad's there will be a short period of toggle
from high to low on the IO when GPIO is set low during
boot. To avoid this glitch, disable pull-up configuration
in GPIO pinmux.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Add support in mxc_i2c driver, iomux_v3 and vf610 architecture for the four
I2C instances available in VF610.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Add IOMUX for the pad used as USB pen. This needs to be driven low for
the Iris and Viola boards where it is pulled up high by default. This is
required for the USB host functionality to work on these boards. Use the
board specific weak initialisation function, to drive the pin low which
would be called on "usb start".
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Inorder to use the pins as GPIO, apart from setting the alt-function,
pinmuxing need to be done, this patch adds pinmux entries of
few GPIOs.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Removed settings in unsupported register fields. They didn’t
do anything, and in most cases, were not documented in the
reference manual.
Changed register settings to comply with JEDEC required values.
Changed timing parameters because they included full clock
periods that were doing nothing.
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
[rebased on v2014.10-rc2]
Signed-off-by: Stefan Agner <stefan@agner.ch>
Add pin mux for NAND Flash Controller (NFC). NAND can be connected
using 8 or 16 data lines, this patch adds pin mux entries for all
16 data lines.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Add QSPI support for VF610TWR, such as clock and iomux.
Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
This patch contains several changes required for second Ethernet
(enet1/RMII1) port on vf610
- ANADIG PLL5 control definitions required for Ethernet RMII1 clock
- Secondary Ethernet (enet1) MAC RMII1 base address definition
- RMII1 iomux definitions
- VF610_PAD_PTA6__RMII0_CLKOUT iomux definition required for
internal (e.g. crystal-less) Ethernet clocking.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[stefan@agner.ch: regrouped patch]
Signed-off-by: Stefan Agner <stefan@agner.ch>
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds generic codes to support Freescale's Vybrid VF610 CPU.
It aligns Vybrid VF610 platform with i.MX platform. As there are
some differences between VF610 and i.MX platforms, the specific
codes are in the arch/arm/cpu/armv7/vf610 directory.
Signed-off-by: Alison Wang <b18965@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
