make the CPU clock selectable via Kconfig
this removes the sunxi specific CONFIG_CLK_FULL_SPEED defined in each
soc header and replaces it's use in board/sunxi/board.c with
CONFIG_SYS_CLK_FREQ from Kconfig which allows us to configure board
specific frequency on boot
Signed-off-by: Iain Paton <ipaton0@gmail.com>
[hdegoede@redhat.com s/CONFIG_SYS_CLK_FREQ/CONFIG_TIMER_CLK_FREQ/ for the
arch-timer clk speed on sun7i to fix mis-compile on sun7i]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add CONFIG_SYS_GENERIC_BOARD to amcc-common.h and CONFIG_DISPLAY_BOARDINFO
to Kconfig files. canyonlands.h includes amcc-common.h, so remove
CONFIG_SYS_GENERIC_BOARD definition there.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Feng Kan <fkan@amcc.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Fix eb_cpu5282 and eb_cpu5282_internal unresolved external error.
These boards have video but don't need any ppc related
video_setmem().
Fix M53017EVB moving away embedded env to a different offset,
as in M52277EVB.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
This variant that is neither FVP / Base Model or Juno Versatile
Express 64bit is confusing. Get rid of it unless someone can
point out what machine that really is. Seems to be an evolutional
artifact in the config base.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This removes the kludgy late board init from the FVP simulator
version of Versatile Express 64bit (ARMv8), and replace it with
a default boot command using the new smhload command to load
the files using semihosting. Tested on the Foundation Model.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
since we have possibility to write out on lcd whats going on, we don't need
the gpio blink functionality anymore.
Signed-off-by: Hannes Petermaier <hannes.petermaier@br-automation.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
At this time I2C and responsible pin-mux is setup during PMIC initialziation
within common.c, this is possible because today PMIC is always connected on
I2C0.
In Future this will be changed, PMIC isn't anymore connected to bus0 in call
cases.
So we do following:
- rename enable_i2c_pin_mux0 to enable_i2c_pin_mux to be generic for enabling
pin-mux on different or more busses.
- move the call to i2c_pin_mux and i2c_init from common.c to the specific
board.c
Signed-off-by: Hannes Petermaier <hannes.petermaier@br-automation.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
BCM2835 (used on Raspberry Pi) and BCM2836 (used on Raspberry Pi 2)
are similar enough. One of the biggest differences is the ARM
processor. It is reasonable to collect the source files into a
single place, arch/arm/mach-bcm283x/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
This option has a bool type, not hex.
Fix it and enable it if CONFIG_DM is on because Driver Model always
requires malloc memory. Devices are scanned twice, before/after
relocation. CONFIG_SYS_MALLOC_F should be enabled to use malloc
memory before relocation. As it is board-independent, handle it
globally.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
The default value of CONFIG_SYS_MALLOC_F_LEN is defined by ./Kconfig
as 0x400. Each defconfig or Kconfig need not repeat the same value.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
After v2015.01 we need to have DM enabled in order to use UART. Also
fix a typo in the EEPROM config format.
Signed-off-by: Gilles Gameiro <gilles@gigadevices.com>
[trini: Reword commit message, re-save defconfigs with 'savedefconfig']
Signed-off-by: Tom Rini <trini@konsulko.com>
Apparently the firmware's board rev response includes both the board
revision and some other data even on the RPi1. In particular, the
"warranty bit" is bit 24. We need to mask that out when looking up the
board ID.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Various files are needlessly rebuilt every time due to the version and
build time changing. As version.h is not actually needed, remove the
include.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: "David Müller" <d.mueller@elsoft.ch>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Torsten Koschorrek <koschorrek@synertronixx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Łukasz Majewski <l.majewski@samsung.com>
This patch enable the MCI support for at91sam9rlek board.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[rebase on ToT]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Larry Johnson <lrj@acm.org>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Eric Millbrandt <emillbrandt@dekaresearch.com>
They have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Erik Theisen <etheisen@mindspring.com>
They have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stephen Williams <steve@icarus.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We don't want that CONSOLE is redirected to LCD upon init, we rather prefer
that console is still on the serial line.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
RX51 has a secure logic which uses different parameters compared to
traditional implementation. So, make the generic secure acr write
over-ride-able by board file and refactor rx51 code to use this.
While at it, enable the OMAP3 specific errata code for 454179, 430973,
621766.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Provide instructions on how to upgrade U-boot in the eMMC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Fix a typo in board/sunxi/Kconfig which caused VIDEO_LCD_PANEL_I2C to be
enabled on all sunxi boards. Also fix a compile error which shows up once
VIDEO_LCD_PANEL_I2C is actually disabled on most boards as it should be.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch add support for Wexler TAB7200 tablet.
The Wexler TAB7200 is a A20 based tablet with 7 inch display(800x480),
capacitive touchscreen(5 fingers), 1G RAM, 4G NAND, micro SD card slot,
mini HDMI port, 3.5mm audio plug, 1 USB OTG port and 1 USB 2.0 port.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Orange Pi Mini is an A20 based development board featuring 1G RAM, HDMI,
1Gbit ethernet, USB wifi, SATA, 2 sdcard slots (use the top one for booting),
2 USB 2.0 A receptacles, a micro USB B receptacle (otg) and a 3 ring 3.5 mm
jack connector for A/V.
Also see: http://www.orangepi.org/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Orange Pi is an A20 based development board featuring 1G RAM, HDMI & VGA,
1Gbit ethernet, USB wifi, SATA, 4 USB 2.0 A receptacles, a micro USB B
receptacle (otg) and a 3 ring 3.5 mm jack connector for A/V.
Also see: http://www.orangepi.org/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Wits Pro A20 DKT is an A20 Development KiT with 1G RAM, 4G NAND, sdio wifi,
1Gbit ethernet, 1024x768 lcd screen with ft5x_ts touchscreen and a ton of
IO connectors.
Note there seem to be multiple sdcard slots on the board (4 in total), but
other then mmc0 none of these are hooked up by default, there is a ton of
dip-switches which likely allow hooking some of these up, but the documentation
of the board only describes the use of a fraction of them, so for now we
only support mmc0.
Also see: http://www.merrii.com/en/pla_d.asp?id=163
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Forfun Q88DB is an A13 tablet in the common Q8 format.
Features are 512MB RAM, 4GB NAND, 7" Display, RTL8188 Wifi, 2 cameras.
For more details see: http://linux-sunxi.org/Forfun_Q88DB
Signed-off-by: Jens Lucius <info@jenslucius.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
The Mele I7 is a Allwinner based Android TV box.
It features a A31 SOC, 1G RAM, 8GB NAND, HDMI out, A/V out,
SPDIF, IrDA, 3 USB A, 1 USB micro OTG and Wireless LAN.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The MK808C is a Allwinner based Android TV dongle.
It features a A20 SOC, 1G RAM, 8GB NAND, HDMI out, A/V out,
1 USB A, 1 USB mini OTG, Bluetooth and Wireless LAN.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Jesurun Q5 has a black plastic casing with the approximate dimensions of
100mm x 100mm x 24mm with rounded edges. In terms of hardware it features an
Allwinner A10 SoC with 1GB RAM and 8GB of NAND flash. The storage capacity can
be extended up to 32GB with a MicroSD card. The external connectors are: 2x
USB-A female supporting USB2.0, 3.5mm female jack for audio, HDMI female,
SPDIF, RJ45 LAN and Power. In addition the device has 1x red LED (hard wired to
power) and an programmable green led. On the board there is also an unpopulated
IR receiver and the UART. The devices is equipped with an AXP209 PMU.
For more details see: http://linux-sunxi.org/Jesurun_Q5
Signed-off-by: Gábor Nyers <gnyers@opensuse.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The tpr3 (timing skew) parameter is used in all supported versions of
the sunxi DRAM controller, but it was only enabled for sun4i in
47e3501a76.
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
While the Freescale ARMv8 board LS2085A will enter U-Boot both
on a master and a secondary (slave) CPU, this is not the common
behaviour on ARMv8 platforms. The norm is that U-Boot is entered
from the master CPU only, while the other CPUs are kept in
WFI (wait for interrupt) state.
The code determining which CPU we are running on is using the
MPIDR register, but the definition of that register varies with
platform to some extent, and handling multi-cluster platforms
(such as the Juno) will become cumbersome. It is better to only
enable the multiple entry code on machines that actually need
it and disable it by default.
Make the single entry default and add a special
ARMV8_MULTIENTRY KConfig option to be used by the
platforms that need multientry and set it for the LS2085A.
Delete all use of the CPU_RELEASE_ADDR from the Vexpress64
boards as it is just totally unused and misleading, and
make it conditional in the generic start.S code.
This makes the Juno platform start U-Boot properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This configures the Juno board to enable ethernet using the
SMSC9118 ethernet controller found in the board. Tested by
TFTP-booting a kernel over ethernet.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch extends OMAP3 support for AM/DM37xx and
introduces the AM3703-based Quipos Cairo board.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Reviewed-by: Simon Glass <sjg@chromium.org>
For some cases it is necessary to modify temporaly the bootcommand.
This can be done by writing into the Scratchregister a specific value:
* 0xCC - modify bootcmd "run netboot"
* 0xCD - modify bootcmd "run netscript"
* 0xCE - modify bootcmd "run mmcboot"
the environment in flash is NOT overwritten.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
vxWorks needs several parameters which are set by the bootloader und his
environment. So we form a vxWorks bootline and pass the result to vxWorks on
a predefined address.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
The board has been redesigned, therefore we need from now other I/O Pins to
mux and handle.
Older boards aren't supported from now anymore.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
