make the CPU clock selectable via Kconfig
this removes the sunxi specific CONFIG_CLK_FULL_SPEED defined in each
soc header and replaces it's use in board/sunxi/board.c with
CONFIG_SYS_CLK_FREQ from Kconfig which allows us to configure board
specific frequency on boot
Signed-off-by: Iain Paton <ipaton0@gmail.com>
[hdegoede@redhat.com s/CONFIG_SYS_CLK_FREQ/CONFIG_TIMER_CLK_FREQ/ for the
arch-timer clk speed on sun7i to fix mis-compile on sun7i]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
clock_set_pll1 would pick the next highest available cpu clock speed if
a value not in the pre defined table was selected. this potentially
results in overclocking the soc.
reverse the selection method so that we select the next lowest speed
and add the missing 912Mhz setting that's requested by sun7i which also
uses the sun4i clock code.
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The usb0 / otg phy on sunxi boards has a bug where it wrongly detects a
high speed squelch on usb reset deassert when a lo speed device is plugged in.
The android kernel has a work around for this in the form of temporary
disabling the phy's squelch detection on reset deassert, this commit adds
the same workaround to the u-boot sunxi musb code, thereby fixing various usb
lo speed devices not working.
Tested with a (before non working) usb keyboard and a usb 2.4 GHz wireless
keyboard/mouse combo receiver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
So that the CONFIG_SPL_FEL option is not needed anymore. And the regular
SPL binary, generated by the default u-boot build, is now also bootable
over USB in the FEL mode. The SPL still can boot from the SD card too.
A bunch of system registers need to be saved/restored in order to ensure
that the IRQ handler still works in the BROM FEL code after getting
control back from the SPL. This is done in the sunxi code instead of
abusing ifdefs in 'start.S'.
The decision whether to load the main u-boot binary from the SD card or
return to the FEL code in the BROM is done at runtime.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[hdegoede@redhat.com: Since we now restore various regs before returning to
the FEL BROM code we can drop the sunxi specific #ifdefs in start.S]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make sunxi's FEL code fit with the normal U-Boot boot sequence instead of
creating its own. There are some #ifdefs required in start.S. Future work
will hopefully remove these.
This series is available at u-boot-dm, branch sunxi-working.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Move the dram helper functions to a separate C file, rather then having them
as inline helpers in dram.h. This saves 144 bytes in the .text segment for
sun6i builds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It turns out that the device_mode_data is rsb specific, rather then slave
specific, so integrate the rsb_set_device_mode() call into rsb_init().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add initial sun9i (A80) clock setup support, enough to get the uart + mmc
going.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
As the comment says now that we have SPL support this is no longer necessary,
as PLL6 is already setup with the exact same parameters by the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2 recent sunxi changes have removed the usage of lowlevel_init by moving some
code around and then setting CONFIG_SKIP_LOWLEVEL_INIT.
This is problematic for 2 reasons:
1) It does not just stop s_init from being called, it also stops
cpu_init_cp15 from getting called, which is undesirable.
2) We want u-boot.bin to be usable standalone, without SPL, some people e.g.
use an upstream u-boot.bin together with Allwinner's boot0 loader. So
u-boot.bin must (re)initialize the gpios, timer, etc.
This commit restores the lowlevel_init / s_init usage, while keeping the
changes to no longer use the global-data (gd) struct in the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This does nothing now, so drop it. We have SPL anyway to do our low-level
init.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The current sunxi implementation uses gdata, which is going away. It also
sets up DRAM before board_init_f() in SPL.
There is really no reason to do much in s_init() since board_init_f() is
called immediately afterwards. The only change is that we need our own
implementation of board_init_f() which sets up DRAM before the BSS (which
is in DRAM) is cleared.
The s_init() code runs once for SPL and again for U-Boot proper. We
shouldn't need to init the clock/timer/gpio/i2c init twice, so just have it
in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
The axp221 / axp223's N_VBUSEN pin can be configured as an output rather
then an input, and this is used on some boards to control usb-vbus0, add
support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Most of the usb-controller init code found in ehci-sunxi.c also is necessary
to init the otg usb controller, so move it to a common place.
While at it also update various #ifdefs / defines for sun8i support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
"adr rX, text_end" only works if the label is close. Adding further code
to the other functions will prevent this. So move the containing
function close to label. No functional change.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Based on the original version by Marc Zyngier. It adds a psci_cpu_off
implementation for the A20 SoC. The mechanism works by first preparing
the calling CPU to go offline (disable and flush cache, disable SMP),
then requesting CPU 0 to pull the plug. The request is sent as FIQ on
SGI15.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
PLL1 on sun6i / sun8i also has a p factor which divides the clock by
2^p (to the power p). On sun6i the p factor is ignored, but on sun8i it is
used and we were setting it to 1, resulting in the CPU running at 504 MHz
instead of 1008 MHz, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
After reboot, reset or even short power off, DRAM typically retains
the old stale data for some period of time (for this type of memory,
the bits of data are stored in slowly discharging capacitors).
The current sun6i/sun8i DRAM size detection logic, which is
inherited from the Allwinner code, relies on using a large magic
signature with the hope that it is unique enough and unlikely to
ever accidentally match this leftover garbage data in RAM. But
this approach is inherently unsafe, as can be demonstrated using
the following test program:
/***** A testcase for reproducing the problem ******/
void main(int argc, char *argv[])
{
size_t size, i;
uint32_t *buf;
/* Allocate the buffer */
if (argc < 2 || !(size = (size_t)atoi(argv[1]) * 1048576) ||
!(buf = malloc(size))) {
printf("Need buffer size in MiB as a cmdline argument\n");
exit(1);
}
/* Fill it with the Allwinner DRAM "magic" values */
for (i = 0; i < size / 4; i++)
buf[i] = 0xaa55aa55 + ((uintptr_t)&buf[i] / 4) % 64;
/* Try to reboot */
system("reboot");
/* And wait */
for (;;) {}
}
/***************************************************/
If this test program is run on the device (giving it a large
chunk of memory), then the DRAM size detection logic in u-boot
gets confused after reboot and fails to initialize DRAM properly.
A better approach is not to rely on luck and abstain from making
any assumptions about the properties of the leftover garbage
data in RAM. Instead just use a more reliable code for testing
whether two different addresses refer to the same memory location.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Based on the register / dram_para headers from the Allwinner u-boot / linux
sources + the init sequences from boot0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sun8i boot0 code fills the DRAM with a "random" pattern before comparing
it at different offsets to do columns, etc. detection. The sun6i boot0 code
does not do it, instead relying on the memory contents being random enough
to begin with for the memcmp to properly detect the wrap-around address, iow
it is working purely by chance. Since our sun6i dram code was modelled after
the boot0 code it contained the same issue.
This commit fixes this by filling the memory with a unique, distinct pattern.
The new mctl_mem_fill function this introduces is added as an inline helper
in dram.h, so that it can be shared with the sun8i dram code.
While at it move mctl_mem_matches to dram.h for re-use in sun8i too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The await_completion helper is already copy pasted between the sun4i and sun6i
dram code, and we need it for sun8i too, so lets make it an inline helper in
dram.h, rather then adding yet another copy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Our old hardcoded k and m values are based on PLL5 being configured in steps
of 48 MHz, which is correct for sun6i where the DRAM PLL runs at twice the
DRAM CLK, which is usually configured in 24 MHz step. But on the A23 (sun8i)
the PLL5 runs at half the DRAM CLK, so we require 12 MHz steps.
This commit adjusts clock_set_pll5 to automatically select the best k and m
depending on the requested clk rate.
Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sun8i dram code sometimes wants to enable sigma delta mode,
add a parameter to allow this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The axp223 appears to be the same as the axp221, except that it uses the
rsb to communicate rather then the p2wi. At least all the registers we use
are 100% the same.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sun8i (A23) introduces a new bus for communicating with the pmic, the rsb,
the rsb is also used to communicate with the pmic on the A80, and is
documented in the A80 user manual.
This commit adds support for this based on the rsb driver from the allwinner
u-boot sources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The p2wi interface is only available on sun6i, adjust the gpio pinmux and
base address defines for it to reflect this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
0x400 is true 1K.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
On sun6i the SID is stored in the pmic, rather then in the SoC itself,
add a helper function to abstract this away.
This makes our MAC address generation code also work on sun6i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A31s only has one dram channel, so do not bother with trying to initialize
a second channel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a sunxi_get_ss_bonding_id() function, and use it to differentiate between
the A31s and the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
It turns out that there is a too large spread between boards to handle this
with a default value, turn this into Kconfig options, and set the values
the factory images are using for the Colombus and Mele_M9 boards.
Note this changes the ZQ default when not overriden through defconfig from
120 to 123, as that is what most boards seem to actually use.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Allwinner tells us that this bit of code is the rtc ram being used to detect
coming out of "super-standby" mode, and if that is the case, going out of
self-refresh mode.
Since we do not support "super-standby" mode, this can be dropped.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is a preparation patch for adding support for HDMI out.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The data sheet just calls it DRAM_CLK_REG, and on sun6i we've both a
dram_clk_cfg and dram_clk_gate, and the sun4i reg matches dram_clk_gate on
sun6i, so name it the same on sun4i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Without this the cache will only work in write-through mode, and as soon as
it is put in write-back mode things break.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add full support for dram initialization, using a fixed clock and autodetection
of the memory organization (numbers of channels, bus-width, etc.).
This is based on dram_sun6i.c and dram.h from u-boot in the Allwinner A31 SDK,
extended with extra initialization sequences and the autodetect algorithm
from boot0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add clock_init_safe and clockset_pll5 functions, as these are needed for
SPL support resp. DRAM init (which is needed for SPL too).
Also add some extra clock register constant defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A31 uses a new push-pull two wire interface, which features higher
transfer speeds (upto 6 MHz) in theory. While the hardware can burst 8
bytes each time, this driver will only see very little use and thus is
limited to single byte transmission only.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
With driver model we will have access to a bank pointer, so we want to
use it rather than converting back to a number, and then back to a
bank pointer. Add functions to provide this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Mostly automatic with:
sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I)
followed by removing the relevant #defines from include/configs/sun?i.h by
hand.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a Kconfig option which users can select when they want to boot older
kernels, e.g. the linux-sunxi 3.4 kernels. For now this just forces the pll5
"p" value to 1 (divide by 2) as that is what those kernels are hardcoded too,
in the future this may enable further workarounds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@ti.com>
--
Changes in v2:
-s/CONFIG_OLD_KERNEL_COMPAT/CONFIG_OLD_SUNXI_KERNEL_COMPAT.
-Move the code block setting P(1) for old kernels to where P gets cleared
This is a preparation patch for making the pll5 "p" divisor configurable
through Kconfig.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is a preparation patch for making the pll5 "p" divisor configurable
through Kconfig.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A23 only has UART0 muxed with MMC0. Some of the boards we
encountered expose R_UART as a set of pads.
Add support for R_UART so we can have a console while using mmc.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The prcm apb0 controls multiple modules. Allow specifying which
modules to enable clocks and de-assert resets so the function
can be reused.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The basic blocks of the A23 are similar to the A31 (sun6i). Re-use
sun6i code for initial clock, gpio, and uart setup.
There is no SPL support for A23, as we do not have any documentation
or sample code for DRAM initialization.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>