Commit Graph

193 Commits

Author SHA1 Message Date
Michal Simek
0bfb43dfc1 xilinx: common: Get rid of fdt_high variable
There is no need to setup this variable if bootm_low and bootm_size
variable are properly setup. If fdt_high variable is missing U-Boot is
asking LMB to return free memory which is not used.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-08-20 09:58:16 +02:00
Michal Simek
2d06361a11 xilinx: zynqmp: Enable DFU tftp support
Enable DFU tftp support for firmware update. Fill dfu_ram_tftp variable to
have command present for showing how to use it.

boot FIT image has been created from below fragment. Key part is that type
of image has to be firmware. Also based on experiment load property is
completely ignored and base addresses are taken from dfu_alt_info variable.

$ cat update_uboot.its
/dts-v1/;

/ {
	description = "Automatic U-Boot update";
	#address-cells = <1>;

	images {
		Image {
			description = "Kernel";
			data = /incbin/("/tftpboot/Image");
			compression = "none";
			arch = "arm64";
			type = "firmware";
			os = "linux";
			load = <0x80000>;
			entry = <0x80000>;
			hash-1 {
				algo = "sha1";
			};
		};
		system.dtb {
			description = "DTB";
			data = /incbin/("/tftpboot/system.dtb");
			compression = "none";
			arch = "arm64";
			type = "firmware";
			load = <0>;
			hash-1 {
				algo = "sha1";
			};
		};
	};
};

$ mkimage -f update_uboot.its /tftpboot/boot

When U-Boot starts get IP address and server IP.
dhcp
setenv serverip 192.168.0.105

And then run prepared command.
run dfu_ram_tftp

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-08-20 09:49:20 +02:00
Michal Simek
9643000e14 xilinx: Align dfu ram with booti command
Image should be loaded to 0x80000 address and not to $kernel_addr_r.
Also kernel_addr, fdt_addr and fdt_size in zynqmp case are not defined
that's why define it to be aligned with Versal.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-08-20 09:49:20 +02:00
Peng Fan
0465f12efb configs: migrate CONFIG_SPL_LOAD_FIT_ADDRESS to defconfigs
Done with:
./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS
./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS -H

Signed-off-by: Peng Fan <peng.fan@nxp.com>
[trini: A few more migrations]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28 16:18:10 -04:00
Adam Ford
acc415ac60 Convert CONFIG_SYS_MMCSD_FS_BOOT_PARTITION to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_MMCSD_FS_BOOT_PARTITION

Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-28 16:18:10 -04:00
Tom Rini
eabbf801c6 Convert CONFIG_BOARD_EARLY_INIT_F et al to Kconfig
This converts the following to Kconfig:
   CONFIG_BOARD_EARLY_INIT_F
   CONFIG_BOARD_EARLY_INIT_R

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-26 10:29:05 -04:00
Tom Rini
e985eb14ac Convert CONFIG_CMD_ASKENV et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_ASKENV
   CONFIG_CMD_BMP
   CONFIG_CMD_BOOTD
   CONFIG_CMD_CACHE
   CONFIG_CMD_CRC32
   CONFIG_CMD_DHCP
   CONFIG_CMD_ENV
   CONFIG_CMD_EXPORTENV
   CONFIG_CMD_EXT2
   CONFIG_CMD_EXT4
   CONFIG_CMD_FLASH
   CONFIG_CMD_FS_GENERIC
   CONFIG_CMD_FUSE
   CONFIG_CMD_GPIO
   CONFIG_CMD_GPT
   CONFIG_CMD_GREPENV
   CONFIG_CMD_I2C
   CONFIG_CMD_IMLS
   CONFIG_CMD_IMPORTENV
   CONFIG_CMD_LOADB
   CONFIG_CMD_LOADS
   CONFIG_CMD_MEMINFO
   CONFIG_CMD_MII
   CONFIG_CMD_MTDPARTS
   CONFIG_CMD_NAND
   CONFIG_CMD_NAND_TRIMFFS
   CONFIG_CMD_NFS
   CONFIG_CMD_PCA953X
   CONFIG_CMD_PCA953X_INFO
   CONFIG_CMD_PCI
   CONFIG_CMD_PING
   CONFIG_CMD_READ
   CONFIG_CMD_SF
   CONFIG_CMD_SPI
   CONFIG_CMD_SPL
   CONFIG_CMD_SPL_WRITE_SIZE
   CONFIG_CMD_TIME
   CONFIG_CMD_TRACE
   CONFIG_CMD_UBI
   CONFIG_CMD_UBIFS
   CONFIG_CMD_UNZIP
   CONFIG_FS_EXT4

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04 18:10:02 -04:00
Tom Rini
c2a38411d1 serial: Convert ARM_DCC to Kconfig
The symbol "CONFIG_ARM_DCC" is used to control building
drivers/serial/arm_dcc.c.  Provide a simple Kconfig entry for this.

Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
2020-06-04 15:04:11 -04:00
Ashok Reddy Soma
702de89cc6 treewide: mem: Move mtest related defines to Kconfig
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-08 12:02:56 -04:00
Michal Simek
e519f03a18 cmd: mem: Remove CONFIG_SYS_MEMTEST_SCRATCH mapping
There is no real need to exactly define space for saving patterns for
alternate memory test. It is much easier to allocate space on the stack and
use it instead of trying to find out space where pattern should be saved.

For example if you want to test the whole DDR memory you can't save patter
to DDR and you need to find it out. On Xilinx devices DDR or OCM addresses
were chosen but that means that OCM needs to be mapped and U-Boot has
access permission there.

It is easier to remove this limitation and simply save it on stack because
it is very clear that memory test can't rewrite U-Boot and U-Boot has also
full access to memory where runs from.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
2020-05-08 09:16:26 -04:00
Michal Simek
19d1304505 xilinx: Make Xilinx custom distro boot commands more verbose
Extend description of Xilinx custom boot commands to make clear what runs
and what failed.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-27 14:21:18 +02:00
Michal Simek
727b396085 arm64: zynqmp: Move PANIC to Kconfig
Convert another option Kconfig.

Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:54 +01:00
Michal Simek
5b21d648cb arm64: zynqmp: Add support for u-boot.itb generation with ATF
Follow i.MX, Sunxi, RISC-V and Rockchip to generate u-boot.itb which
includes U-Boot proper, ATF and DTBs in FIT format. ZynqMP supports FIT for
quite a long time but with using out of tree solution. The patch is filling
this gap.

Tested on zcu102, zcu104 and zcu100/Ultra96.

zcu100/Ultra96 v2.2 ATF build by:
make DEBUG=0 ZYNQMP_CONSOLE=cadence1 RESET_TO_BL31=1 PLAT=zynqmp bl31

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:54 +01:00
T Karthik Reddy
53c69dec33 board: xilinx: Add support for user configurable boot script offset
Currently "script_offset_f" env variable is hardcoded, this variable
specifies from which offset of the flash boot.scr should be read/write.
As flashes are of different sizes having a fixed offset makes it
difficult to load other images into the flash which may overwrite the
boot script or cannot utilize the full memory. This current fix
creates a new config "CONFIG_BOOT_SCRIPT_OFFSET" which holds the
offset address, overwrites the "script_offset_f" variable.
Also removed existing variable with default values, as the default
values are held by CONFIG_BOOT_SCRIPT_OFFSET

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:52 +01:00
Siva Durga Prasad Paladugu
5d2274c00f arm64: zynqmp: Add new jtag distro boot command
This patch adds new jtag distro boot command to look for bootscript file in
DDR and execute it first incase of jtag bootmode.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08 09:35:43 +02:00
Siva Durga Prasad Paladugu
81764f5361 arm64: zynqmp: Update scriptaddr value to 512MB
This patch updates scriptaddr value to 512MB as having it at 32MB has high
chance of script corruption incase of bigger kernel.

Be aware that 512MB is used for SPL malloc area that's why images should be
loaded after SPL (the best after u-boot relocation).

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08 09:35:43 +02:00
T Karthik Reddy
a69814c815 arm64: zynqmp: Set initrd_high to as high as possible
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08 09:11:14 +02:00
Hannes Schmelzer
1ee774d209 Convert CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_SPI_U_BOOT_OFFS

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
[trini: Expose this for SPL_SPI_SUNXI for now]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25 20:59:00 -04:00
Hannes Schmelzer
abf9e5d0f2 moveconfig: prepare moving CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig step 2
some boards have common headers for several individual build-targets
where CONFIG_SYS_SPI_U_BOOT_OFFS is defined even it is not needed (only
needed if CONFIG_SPL_SPI_LOAD is defined also). Take this define here
under '#ifdef CONFIG_SPL_SPI_LOAD' for having a clean run of
moveconfig.py

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-08-25 20:58:59 -04:00
Robert P. J. Day
ce7b93d4fc ARM: zynq: delete long-dead CONFIG_USB_CABLE_CHECK
This Kbuild option disappeared way back in 2014:

 commit 75504e9592
 Author: Mateusz Zalega <m.zalega@samsung.com>
 Date:   Wed Apr 30 13:07:48 2014 +0200

    ... snip ...

    CONFIG_USB_CABLE_CHECK was removed.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-30 10:20:06 +02:00
Alex Kiernan
623de3f086 Convert CONFIG_SUPPORT_EMMC_BOOT to Kconfig
This converts the following to Kconfig:
   CONFIG_SUPPORT_EMMC_BOOT

As requested by Michal Simek <michal.simek@xilinx.com>, these boards
have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:

  xilinx_zynqmp_zc1275_revB
  xilinx_zynqmp_zc1751_xm018_dc4
  xilinx_zynqmp_zc1751_xm019_dc5
  xilinx_zynqmp_zcu100_revC
  xilinx_zynqmp_zcu102_rev1_0
  xilinx_zynqmp_zcu102_revA
  xilinx_zynqmp_zcu102_revB
  xilinx_zynqmp_zcu104_revA
  xilinx_zynqmp_zcu104_revC
  xilinx_zynqmp_zcu106_revA
  xilinx_zynqmp_zcu111_revA

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-05-04 13:04:12 -04:00
Simon Goldschmidt
f89d6133ee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Michal Simek
cc9f55e241 arm64: zynqmp: Remove eeprom setting
By moving to DM_I2C there is no need to specify any eeprom configuration
because it is read from DT.

Reported-by: Sreeja Vadakattu <sreeja.vadakattu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16 11:52:02 +02:00
Michal Simek
8bdad43333 arm64: zynqmp: Switch all platforms to DM_I2C
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio
subsystem already. That's why also remove CMD_PCA953X which is only for
this driver.

zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address.

DM_I2C is not enabled for the whole SoC because it increase size for
mini configurations and there is no I2C symbol present to setup
dependencies.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2019-02-14 14:31:10 +01:00
Siva Durga Prasad Paladugu
ad78d2641f arm64: zynqmp: Define distro boot commnads for qspi and nand
This patch adds distro boot commands for qspi and nand. The
distro boot commands now reads the script from flash offset
of 63.5MB and executes it.

Setup default location via script_offset_f to 63.5MB to match the most
xilinx reference boards. 512kB allocated space for script size
(script_size_f) should be more than enough to cover custom boot logic.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-14 14:31:09 +01:00
Andrew F. Davis
6536ca4d66 spl: Kconfig: Drop the _SUPPORT postfix from SPL_DFU
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
2019-01-26 08:13:54 -05:00
Tuomas Tynkkynen
1bc93b50e8 ata: Drop CONFIG_SYS_SCSI_MAX_* from boards using DM_SCSI
These options are not used or necessary when device model is being used
for SCSI. Just drop them.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-25 21:49:18 -04:00
Adam Ford
d7869b2183 Convert CONFIG_MII et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MII
   CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-17 13:03:54 -04:00
Tom Rini
86cf1c8285 configs: Migrate CONFIG_NR_DRAM_BANKS
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 16:45:02 -04:00
Adam Ford
9c5b00973b Convert CONFIG_MTD_PARTITIONS et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MTD_PARTITIONS
   CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-22 19:20:17 -04:00
Vipul Kumar
2a30809cae env: Added support to save env to spi through Kconfig
This patch added support to enable CONFIG_ENV_SIZE, CONFIG_ENV_OFFSET
and CONFIG_ENV_SECT_SIZE through Kconfig for Zynq and Zynqmp.

Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:56 +02:00
Siva Durga Prasad Paladugu
0fd2290cfc cmd: Kconfig: Move CONFIG_MP to Kconfig
This patch moves CONFIG_MP to Kconfig

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-10 16:55:59 -04:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Joe Hershberger
86271b3f29 xilinx: Only enable dist boot pxe when DHCP is enabled
Otherwise, we see this:
In file included from include/configs/zynq-common.h:183:0,
                 from include/config.h:5,
                 from include/common.h:21,
                 from env/common.c:11:
include/config_distro_bootcmd.h:319:2: error: expected ?}? before ?BOOT_TARGET_DEVICES_references_PXE_without_CONFIG_CMD_DHCP_or_PXE?
  BOOT_TARGET_DEVICES_references_PXE_without_CONFIG_CMD_DHCP_or_PXE
  ^
include/config_distro_bootcmd.h:319:2: note: in definition of macro ?BOOTENV_DEV_NAME_PXE?

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:48:38 -05:00
Marek Vasut
555004381e spl: spi: Move CONFIG_SPL_SPI_LOAD to Kconfig
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
2018-04-11 13:22:00 -04:00
Michal Simek
1a82f59b31 arm64: zynqmp: Enable pxe and dhcp if commands are enabled
Targets without net can't use pxe or dhcp boot methods.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09 12:14:51 +02:00
Mario Six
02ddc1477c treewide: Migrate CONFIG_BOARD_EARLY_INIT_R to Kconfig
Migrate the CONFIG_BOARD_EARLY_INIT_R option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08 14:52:54 -04:00
Mario Six
e89f8aae3d treewide: Migrate CONFIG_SYS_ALT_MEMTEST to Kconfig
Migrate the CONFIG_SYS_ALT_MEMTEST option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration after also including CMD_MEMTEST]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-08 14:52:45 -04:00
Vipul Kumar
fce0a6b521 arm64: zynqmp: Changed scratch address used by the alternate memory test
This patch changed CONFIG_SYS_MEMTEST_SCRATCH address to the
accessible DDR address used by alternate memory test.
Before this, 0xfffc0000 address was used, which is the OCM
address and not enabled in MMU table. So, whenever trying
to access 0xfffc0000 address, got Synchronous Abort exception.

After changing CONFIG_SYS_MEMTEST_SCRATCH address, alternate
memory test is working fine.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-23 09:34:44 +01:00
Tom Rini
6f6b7cfa89 Convert all of CONFIG_CONS_INDEX to Kconfig
This converts the following to Kconfig:
   CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them.  They're also sometimes used for things not
directly inside of the serial driver.  First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it.  Next, consolidate all of these into the single entry in
drivers/serial/Kconfig.  Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-16 10:28:52 -04:00
Vipul Kumar
5dc5a53c5e mmc: Added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01 16:44:10 +01:00
Vipul Kumar
ce3c9a59af i2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SPEED
This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SPEED
and set it to default value 100000.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01 08:03:01 +01:00
Vipul Kumar
e7affad190 i2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVE
This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVE
and set it default to 0.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01 08:03:01 +01:00
Adam Ford
ba8bf9481b Remove config_distro_defaults.h
With the contents of config_distro_defaults.h migrated to Kconfig,
we can remove this header file completely

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-02-23 21:44:22 -05:00
Adam Ford
d021e94210 Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig
This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23 21:41:49 -05:00
Tom Rini
75670c81e4 configs: Migrate CONFIG_SPL_FRAMEWORK
Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig.  We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important.  In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-14 12:14:13 -05:00
Lukasz Majewski
c6c1ca100f Kconfig: gadget: Move CONFIG_USB_FUNCTION_THOR to Kconfig
This commit moves USB_FUNCTION_THOR config to Kconfig.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-02-02 07:13:48 -05:00
Vipul Kumar
aae7422b45 arm64: zynqmp: Moved ethernet PHY configs of ZynqMP boards to defconfig
This patch moved ethernet PHY configs of ZynqMP boards
to respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30 14:29:52 +01:00
Michal Simek
88f05a926d arm64: zynqmp: Call psu_init() only when ZYNQMP_PSU_INIT_ENABLED
Remove SPL_BUILD dependency from zynqmp.c and move it to header file.
Use only one symbol for including psu_init.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30 14:29:12 +01:00
Ezequiel Garcia
d55c8159bd nand: arasan: Select CONFIG_SYS_NAND_SELF_INIT
The Arasan NFC driver requires the self-init mode,
so it should select it.

Instead of having the config header define the macro,
it's cleaner to select the option at the Kconfig level.

Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30 14:29:07 +01:00