This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move CONFIG_SYS_ARM_CACHE_WRITETHROUGH and
CONFIG_SYS_ARM_CACHE_WRITEALLOC into Kconfig done by moveconfig.py.
Kconfig uses a choice between the 3 values supported in U-Boot,
including the new configuration CONFIG_SYS_ARM_CACHE_WRITEBACK
(the default configuration).
The patch also avoids to select simultaneously 2 configurations.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>
Move the U-Boot environment to 0x80000 to match the downstream
vendor fork and allow easy migration from one to the other.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add board code and DTs for Renesas RZ/A1 SoC-based GR-Peach,
which is a cheap development platform with RZ/A1H SoC. The
DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Currently supported are UART, ethernet and RPC SPI. The board
can be booted from RPC SPI by writing the u-boot.bin binary
to the beginning of the SPI NOR, e.g. using the "sf" command.
The board can also be booted via JTAG by setting text base to
0x20020000, loading u-boot.bin there via JTAG and executing it
from that address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
