This patch enables CONFIG_SYS_BOOT_RAMDISK_HIGH for RISC-V
because bootm will update initrd location in DTB only if
CONFIG_SYS_BOOT_RAMDISK_HIGH is enabled. If we don't enable
this option then bootm assumes DTB already has initrd details
which is not the case most of the time.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The readme guide describes the procedure to build, flash and boot Linux
using U-Boot on HiFive Unleashed. It also explains the current state of
U-boot support and future action items.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
This patch adds SiFive FU540 board support. For now, only
SiFive serial, SiFive PRCI, and Cadance MACB drivers are
only enabled. The SiFive FU540 defconfig by default builds
U-Boot for S-Mode because U-Boot on SiFive FU540 will run
in S-Mode as payload of BBL or OpenSBI.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Currently, timer driver is bound only for hart0.
There is no mandatory requirement that hart0 should always
come up. In fact, HiFive Unleashed SoC hart0 doesn't boot
in S-mode because it only has M-mode.
The timer driver should be bound for boot hart.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is possible that input clock is not available because clk
device was not available and 'clock-frequency' DT property is
also not available.
In this case, instead of failing we should just skip baudrate
config by returning zero.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
This patch adds fixed-factor clock driver which derives clock
rate by dividing (div) and multiplying (mult) fixed factors
to a parent clock.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add driver code for the SiFive FU540 PRCI IP block. This IP block
handles reset and clock control for the SiFive FU540 device and
implements SoC-level clock tree controls and dividers.
Based on code written by Wesley Terpstra <wesley@sifive.com>
found in commit 999529edf517ed75b56659d456d221b2ee56bb60 of:
https://github.com/riscv/riscv-linux
Boot and PLL rate change were tested on a SiFive HiFive Unleashed
board.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Fix MID bit field check to correctly identify all GEM hardwares.
The check is updated as per macb driver in Linux location:
<linux_sources>/drivers/net/ethernet/cadence/macb_main.c:259
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Don't fail in macb_enable_clk() if clk_enable() returns
-ENOSYS because we get -ENOSYS for fixed-rate clocks.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On 64bit systems, the DRAM top can be easily beyond 4GB and U-Boot
DMA mapping APIs will generate DMA addresses beyond 4GB. This
breaks DMA programming in 32bit DMA capable devices (such as
Cadence MACB ethernet). For example, If DRAM is more then 2GB
on QEMU sifive_u machine then Cadence MACB ethernet stops working
for U-Boot because it is a 32bit DMA capable device.
To handle 32bit DMA capable devices on 64bit systems, we provide
custom implementation of board_get_usable_ram_top() which ensures
that usable ram top is not more then 4GB. This in-turn ensures
that U-Boot always runs within 4GB hence DMA addresses generated
by DMA mapping APIs will be within 4GB too.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some of the drivers (such as Cadence MACB ethernet driver) expect
asm/arch/clk.h to be provided by arch support so we add place-holder
asm/arch-generic/clk.h for RISC-V generic CPU.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
This patch adds asm/dma-mapping.h for Linux-like DMA mappings
APIs required by some of the drivers (such as, Cadance MACB
Ethernet driver).
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The QEMU CPU support under arch/riscv is pretty much generic
and works fine for SiFive Unleashed as well. In fact, there
will be quite a few RISC-V SOCs for which QEMU CPU support
will work fine.
This patch renames cpu/qemu to cpu/generic to indicate the
above fact. If there are SOC specific errata workarounds
required in cpu/generic then those can be done at runtime
in cpu/generic based on CPU vendor specific DT compatible
string.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We select CREATE_ARCH_SYMLINK for RISC-V so that we can have
include/asm/arch linked to include/asm/arch-xyz.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A new option -e is added to the env command which allows to display and
change UEFI variables in a user friendly way.
A new command efidebug is introduced to edit the UEFI boot sequence and to
display different aspects of the state of the UEFI sub-system: memory map,
loaded images, handles, drivers and devices.
A bug in the UEFI boot manager is fixed.
-----BEGIN PGP SIGNATURE-----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=tE3A
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-04-rc3' of https://github.com/xypron2/u-boot
Pull request for the UEFI sub-system for v2019.04-rc3
A new option -e is added to the env command which allows to display and
change UEFI variables in a user friendly way.
A new command efidebug is introduced to edit the UEFI boot sequence and to
display different aspects of the state of the UEFI sub-system: memory map,
loaded images, handles, drivers and devices.
A bug in the UEFI boot manager is fixed.
According to latest specification rev.0026 and after confirmation with
HW engineer, the DTCNTL register TAPNUM field must be set to 8 even on
H3 ES2.0 SoC. Make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
According to latest specification rev.0026, when HOST_MODE bit 0
(WMODE) is not set, HOST_MODE bit 8 (BUSWIDTH) is ignored. Clear
HOST_MODE bit 8 in such case and align the code with Linux and
avoid possible unforeseen issues.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Convert R-Car Gen2 from OF_EMBED to OF_SEPARATE, thus getting
rid of one of the deprecation warnings.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize Gen3 defconfigs in wake of the Kconfig option changes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Imply all SoCs supported by a given board. This allows building single
U-Boot binary for boards which can have multiple SoCs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop per SoC def_bool on each driver, since this is now implied by
SoC Kconfig option instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop per SoC def_bool on each driver, since this is now implied by
SoC Kconfig option instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Imply preferred pin control driver per SoC, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
On SoCFPGA Gen5 systems, it can rarely happen that a reboot from Linux
will result in stale data in PL310 L2 cache controller. Even if the L2
cache controller is disabled via the CTRL register CTRL_EN bit, those
data can interfere with operation of devices using DMA, like e.g. the
DWMMC controller. This can in turn cause e.g. SPL to fail reading data
from SD/MMC.
The obvious solution here would be to fully reset the L2 cache controller
via the reset manager MPUMODRST L2 bit, however this causes bus hang even
if executed entirely from L1 I-cache to avoid generating any bus traffic
through the L2 cache controller.
This patch thus configures and enables the L2 cache controller very early
in the SPL boot process, clears the L2 cache and disables the L2 cache
controller again.
The reason for doing it in SPL is because we need to avoid accessing any
of the potentially stale data in the L2 cache, and we are certain any of
the stale data will be below the OCRAM address range. To further reduce
bus traffic during the L2 cache invalidation, we enable L1 I-cache and
run the invalidation code entirely out of the L1 I-cache.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Configure the PL310 tag and data latency registers, which slightly
improves performance and aligns the behavior with Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
The loop implemented in the code is supposed to check whether the
PL310 operation register has any bit from the mask set. Currently,
the code checks whether the PL310 operation register has any bit
set AND whether the mask is non-zero, which is incorrect. Fix the
conditional.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Tom Rini <trini@konsulko.com>
Fixes: 93bc21930a ("armv7: add PL310 support to u-boot")
gpio_get_value should return 0 or 1, not the value of bit & (1 << pin)
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
"drivers" command prints all the uefi drivers on the system.
=> efi drivers
Driver Name Image Path
================ ==================== ====================
000000007ef003d0 <NULL> <built-in>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
"devices" command prints all the uefi variables on the system.
=> efi devices
Scanning disk ahci_scsi.id0lun0...
Scanning disk ahci_scsi.id1lun0...
Found 4 disks
Device Device Path
================ ====================
000000007ef07ea0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)
000000007ef00c10 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(0,0)
000000007ef00dd0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(1,0)
000000007ef07be0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(1,0)/HD(1,MBR,0x086246ba,0x800,0x40000)
000000007ef07510 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(1,0)/HD(2,MBR,0x086246ba,0x40800,0x3f800)
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently, there is no easy way to add or modify UEFI variables.
In particular, bootmgr supports BootOrder/BootXXXX variables, it is
quite hard to define them as u-boot variables because they are represented
in a complicated and encoded format.
The new command, efidebug, helps address these issues and give us
more friendly interfaces:
* efidebug boot add: add BootXXXX variable
* efidebug boot rm: remove BootXXXX variable
* efidebug boot dump: display all BootXXXX variables
* efidebug boot next: set BootNext variable
* efidebug boot order: set/display a boot order (BootOrder)
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
"env [print|set] -e" allows for handling uefi variables without
knowing details about mapping to corresponding u-boot variables.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Since commit 914df75b0c ("efi_loader: fix EFI entry counting")
entry_count is already set to 1 before efi_bootmgr_load() is called. So we
should not increment it when entering the function.
Without the patch an assert error occurs in efi_get_variable() if DEBUG is
defined.
Fixes: 914df75b0c ("efi_loader: fix EFI entry counting")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
For booting via `bootefi bootmgr` it is necessary that the EFI variable
BootOrder is defined. Provide a diagnostic message if the variable is
missing.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is the same migration path as commit b6251db8c3 ("Kconfig:
Introduce USE_BOOTCOMMAND and migrate BOOTCOMMAND").
I also moved the description in README to the Kconfig help.
I ripped off the sentence about 'LWMON' since it is gone already.
I only let my boards migrate, leaving the rest to platform maintainers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Without CONFIG_LED, we get
cmd/built-in.o: In function `show_led_state':
cmd/led.c:40: undefined reference to `led_get_state'
cmd/built-in.o: In function `do_led':
cmd/led.c:99: undefined reference to `led_get_by_label'
cmd/led.c:108: undefined reference to `led_set_state'
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
- Add support for sound.
Albeit the big changeset, changes are pretty limited to x86 only and a
few new sound drivers used by x86 so I think it would be good to have
this in the next release.
U-Boot typically tears down the display controller before handing
control over to Linux. On LCD displays disabling pixel clock leads to a
fading out effect with vertical/horizontal lines. Make sure to disable
back light before booting Linux.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The CONFIG_KEYBOARD does nothing as it's legacy and unused
so just drop it from the config.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Migrate TEGRA_KEYBOARD from headers to Kconfig, only the seaboard uses it but we
drop CONFIG_KEYBOARD as the driver doesn't use the legacy drv_keyboard_init.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
