Add support for Exynos7420 SoC. The Exynos7420 SoC has four Cortex-A57
and four Cortex-A53 CPUs and includes various peripheral controllers.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The existing Exynos 32-bit platform support needs to be realigned in
order to support newer 64-bit Exynos platforms. The driver model will
be utlized for drivers on the 64-bit Exynos platforms and so some of
the older platform support code would not be required for the newer
64-bit Exynos platforms.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Fix typo error for cpsw device name with proper device address
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add syscon node to cpsw device node to read mac address
from efuse.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add syscon node to cpsw device node to read mac address
from efuse.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add platforms specific phy mode configuration bits to be used
to configure phy mode in control module.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Extending Kconfig for adding new platform is a lot of work
for nothing. Setting SYS_CONFIG_NAME directly in Kconfig and
remove all dependencies on TARGET_ZYNQ_* options including SPL.
As a side-effect it also remove custom init folder for ps7_init_gpl.*
files. Folder is chosen based on device-tree file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Support RAM and MMC boot mode in SPL also with SPL_FIT images.
In MMC boot mode two boot options are available:
1) Boot flow with ATF(EL3) and full U-Boot(EL2):
aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
mkimage -A arm64 -O linux -T kernel -C none -a 0xfffe5000 -e 0xfffe5000
-d bl31.bin atf.ub
cp spl/boot.bin <sdcard fat partition>
cp atf.ub <sdcard fat partition>
cp u-boot.bin <sdcard fat partition>
2) Boot flow with full U-Boot(EL3):
cp spl/boot.bin <sdcard>
cp u-boot*.img <sdcard>
3) emmc boot mode
dd if=/dev/zero of=sd.img bs=1024 count=1024
parted sd.img mktable msdos
parted sd.img mkpart p fat32 0% 100%
kpartx -a sd.img
mkfs.vfat /dev/mapper/loop0p1
mount /dev/mapper/loop0p1 /mnt/
cp spl/boot.bin /mnt
cp u-boot.img /mnt
cp u-boot.bin /mnt
cp atf.ub /mnt
umount /dev/mapper/loop0p1
kpartx -d sd.img
cp sd.img /tftpboot/
and program it via u-boot
tftpb 10000 sd.img
mmcinfo
mmc write 10000 0 $filesize
mmc rescan
mmc part
ls mmc 0
psu_init() function contains low level SoC setup generated for every HW
design by Xilinx design tools. xil_io.h is only supporting file to fix
all dependencies from tools. The same solution was used on Xilinx Zynq.
The patch also change CONFIG_SYS_INIT_SP_ADDR to the end of OCM which
stays at the same location all the time.
Bootrom expects starting address to be at 0xfffc0000 that's why this
address is SPL_TEXT_BASE.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The GIC ranges in the zynqmp device tree are only 4kb aligned. Since
commit 12e14066f we automatically deal with aliases GIC regions though,
so we can map them transparently into guests even on 64kb page size
systems.
This patch makes use of that features and sets GICC and GICV to 64kb
aligned and sized regions.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If ps7_post_config() is defined call it. It is enabling for example
level shifters for PL bitstreams.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Commit 9f56917ab8 ("dm: core: make simple-bus compatible to
simple-mfd") made possible to import the following commit:
Linux commit: bc5ba9b98435bf76d92e0954da1784695aa449f1
The SLCR (System-Level Control Registers) block is an MFD (Multi
Function Device) rather than a bus.
"simple-mfd" seems a more suitable compatible string than "simple-bus".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Implement support for saving ARM register R4 early during boot using
save_boot_params . Implement support for decoding the stored register
R4 value in spl_boot_device() to obtain boot device from which the
SoC booted. This way, the SPL will always load U-Boot from the same
device from which the SPL itself booted instead of using hard-coded
boot device.
This functionality is useful for example when booting sama5d2-xplained
from SD card, where by default the SPL would try loading the U-Boot
from eMMC and fail. This is because eMMC is on SDHCI0 (BOOT_DEVICE_MMC1),
while SD slot is on SDHCI1 (BOOT_DEVICE_MMC2) and the SPL was hard-wired
to always boot from BOOT_DEVICE_MMC1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Add the UPLL clock and master clock as a clock source for getting
the generated clock frequency to complete its clock sources support.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Before enabling a generated clock whose source is from the UPLL
clock, check and enable the UPLL clock.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
The board supports following features:
- Boot media support: NAND Flash/SPI Flash
- Support ethernet
- Support USB mass storage
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
During DDR-2133 operation, the transmit data eye margins determined
during the memory controller initialization may be sub-optimal, set
DEBUG_29[12] and DEBUG_29[13:16] = 4'b0100 before MEM_EN is set.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some SOCs, specifically the ones in the C29x familiy can have
multiple security engines. This patch adds a system configuration
define which indicates the maximum number of SEC engines that
can be found on a SoC.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Freescale PPC SoCs do not hard-code security engine's Job Ring 0
address, rather a define is used. This patch adds the same
functionality to the ARM based SoCs (i.e. LS1/LS2 and i.MX parts)
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MMCSD_MODE_FAT has been renamed to MMCSD_MODE_FS by commit 205b4f33.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MMCSD_MODE_FAT has be renmaed to MMCSD_MODE_FS by commit 205b4f33.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
init_early_memctl_regs() is also be called in board_early_init_f().
So remove the duplicated call in spl code.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the issue about the stack will get corrupted when switching between
the early and final mmu tables is fixed by commit 70e21b064, the
workaround to flush dcache is unnecessary and should be removed.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The address value and size value set for QSPI dts node "reg"
property have type of u64 on arm64.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For Qoriq PPC&ARM v7 platforms, the crypto node is being fixup'ed in
order to update the SEC internal version (aka SEC ERA). This patch
adds the same functionality to the ARMv8 SoCs.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The initial training for the DDRC may provide results that are not
optimized. The workaround provides better read timing margins.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This option currently enables both the command and the SCSI functionality.
Rename the existing option to CONFIG_SCSI since most of the code relates
to the feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
1. Support compatible string "spi-gpio" which is used by Linux
Linux use different bindings, so use UBOOT_COMPAT and
LINUX_COMPAT to differentiate them.
2. Introduce SPI_MASTER_NO_RX and SPI_MASTER_NO_TX to handle
no rx or no tx case.
3. Tested on i.MX6 UltraLite board with 74LV595 spi-gpio chip.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This prevents the following boot-time message on any board where only the
first DC is in use, yet the DC's DT node is enabled:
stdio_add_devices: Video device failed (ret=-22)
(This happens on at least Harmony, Ventana, and likely any other Tegra20
board with display enabled other than Seaboard).
The Tegra DC's DT node represents a display controller. It may itself
drive an integrated RGB display output, or be used by some other display
controller such as HDMI. For this reason the DC node itself is not
enabled/disabled in DT; the DC itself is considered a shared resource, not
the final (board-specific) display output. The node should instantiate a
display output driver only if the rgb subnode is enabled. Other output
drivers are free to use the DC if they are enabled and their DT node
references the DC's DT node. Adapt the Tegra display drivers' bind()
routine to only bind to the DC's DT node if the RGB subnode is enabled.
Now that the display driver does the right thing, remove the workaround
for this issue from Seaboard's DT file.
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
According to the product website, the full names are i.MX 7Solo
and i.MX 7Dual, whereas the short form is i.MX7S and i.MX7D. Be
consistent and print the short form for both supported i.MX 7 SoCs.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The clock parent of the AHB root clock when using mux option 1
is the SYS PLL 270MHz clock. This is specified in Table 5-11
Clock Root Table of the i.MX 7Dual Applications Processor
Reference Manual.
While it could be a documentation error, the 270MHz parent is
also mentioned in the boot ROM configuration in Table 6-28: The
clock is by default at 135MHz due to a POST_PODF value of 1
(=> divider of 2).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Several UART input selects are missing. The fourth input select
for UART2_TX_DATA_ALT0 is actually also missing in the documentation.
(at least in Rev. B of the i.MX 7Dual Reference Manual). However,
when looking at the tables of other input selects, it is very natural
that there must be an input select for the UART2_TX_DATA_ALT0 pad.
The Colibri iMX7 also uses that pad for UART2 RX (in DTE mode), and
it was required to set that particular input select register to get a
working UART2.
This patch adds the IOMUX setting for using SD1_DAT5 as GPIO5:9.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Peng Fan <van.freenix@gmail.com>
Commit bfb33f0bc4 ("sunxi: mctl_mem_matches: Add missing memory
barrier") broke compilation for the Pine64, as dram_helper.c now
includes <asm/armv7.h>, which does not compile on arm64.
Fix this by moving all barrier instructions into a separate header
file, which can easily be shared between arm and arm64.
Also extend the inline assembly to take the "sy" argument, which is
optional for ARMv7, but mandatory for v8.
This fixes compilation for 64-bit sunxi boards (Pine64).
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is mandatory, otherwise the USB does not work.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
According PL310 TRM, Auxiliary Control Register
"
The register must be written to using a secure access, and it can be
read using either a secure or a NS access. If you write to this register
with a NS access, it results in a write response with a DECERR response,
and the register is not updated. Writing to this register with the L2
cache enabled, that is, bit[0] of L2 Control Register set to 1,
results in a SLVERR.
"
So If L2 cache is already enabled by ROM, chaning value of ACR
will cause SLVERR and uboot hang.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
The current delays in the DDR initialization routines for am33xx
architectures are sometimes not running long enough leading to DDR
init errors. On am437x, this shows up as an L3 NOC error after the
kernel boots. This is due to the timer not being initialized
properly, but instead still containing the timer init values from
the boot ROM which cause timers to expire in 1/4th the time
required.
timer_init is typically not called until board_init_r, however on
am33xx/am43xx udelay is required in sdram_init which is called
from board_init_f, so a call to timer_init is required earlier.
Note that this issue introduced in v2015.01 by:
b352dde "am33xx: Drop timer_init call from s_init".
Although this could instead fixed by reverting said commit, it
would cause timer_init to be called twice in both SPL and non-SPL
cases. This gives a little more fine grained control and also
matches what is being done on omap-command and fsl-layerscape.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Commit 724219a65f "ARM: always perform per-CPU GIC init" removed some
ifdefs to unify the MULTIENTRY-vs-non-MULTIENTRY paths. However, the
wrong endif was removed. This patch adds back that missing endif, and
adds a new ifdef to match the endif the now-correctly-terminated block
used to match against. Use "git show -U25 724219a65f55" to see enough
context to make the original issue clear.
In practical terms, this makes no difference to runtime behaviour. The
code that was incorrectly compiled into the binary when ifndef MULTIENTRY
is a no-op for other cases, since branch_if_master evaluates to a hard-
coded jump. The only issues were:
- A few extra instructions were added to the binary.
- The comment on the endif at the very end of the function, indicating
which ifdef it matched, were wrong.
An alternative might be to simply fix the comment on that trailing ifdef,
but that only addresses the second point above, not the first.
Fixes: 724219a65f ("ARM: always perform per-CPU GIC init")
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In current Linux kernel Tegra DT files, 64-bit addresses are represented
in unit addresses as a pair of comma-separated 32-bit values. Apparently
this is no longer the correct representation for simple busses, and the
unit address should be represented as a single 64-bit value. If this is
changed in the DTs, arm/arm/mach-tegra/board2.c:ft_system_setup() will no
longer be able to find and enable the GPU node, since it looks up the node
by name.
Fix that function to enable nodes based on their compatible value rather
than their node name. This will work no matter what the node name is, i.e
for DTs both before and after any rename operation.
Cc: Thierry Reding <treding@nvidia.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>