As best I can tell, there's no difference between bulk and interrupt
transfers in terms of how the HW should be programmed, at least given
that we're executing one transaction at a time rather than scheduling
them into frames for maximum throughput.
This patch ends up sharing the toggle bit state between bulk and
interrupt transfers on a particular EP. However I believe this is fine;
AFAIK a given EP either uses bulk or interrupt transfers and doesn't mix
them.
This patch doesn't do anything with the "interval" parameter for
interrupt transfers, but then most other USB controller drivers in U-Boot
don't either.
It turns out that one of my keyboards is happy to work using control
transfers but the other only gives non-zero "HID reports" via interrupt
transfers.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
A bit must be set in HCCHAR when communicating with low-speed devices.
I have no idea why there's no corresponding bit to distinguish between
full-speed and high-speed devices, but no matter; they all work now!
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
This doesn't make my LS keyboard work any better, but it does at least
report the correct speed in "usb tree".
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Use of these APIs is required on the Raspberry Pi. With this change, USB
on RPi1 should be more reliable, and USB on the RPi2 will start working.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
When I created wait_for_chhltd(), I noticed that some instances of the
code it replaced expected the ACK bit to be set and others didn't. I
assumed this was an accidental inconsistency in the code, so wrote
wait_for_chhltd() to always expect ACK to be set. This code appeared to
work correctly for both enumeration of USB keyboards and operation of
USB Ethernet devices. However, this change broke USB Mass Storage (at
least my USB SD card reader). This change reverts to exactly the
original behaviour. I'm not sure why the ACK bit isn't always set
(perhaps a quirk in the USB HW or DWC2 controller), but the code works
this way!
Fixes: 5be4ca7d6ac8 ("usb: dwc2: unify waiting for transfer completion")
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Each USB transfer is split up into chunks that are held in an aligned
buffer. This imposes a limit on the size of each chunk, but no limit on
the total size of transferred data. Fix the logic in chunk_msg() not to
reject large transfers, but simply take the size of the aligned buffer
into account when calculating the chunk size.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The original aligned_buffer usage:
a) Uselessly copied data into the aligned buffer even for IN
transactions. Fix this my making the copy conditional.
b) Always programmed the HW to transfer to/from the start of the aligned
buffer. This worked fine for OUT transactions since the memcpy copied
the OUT data to this location too. However, for large IN transactions,
since the copy from the aligned buffer to the "client" buffer was
deferred until after all chunks were transferred. it resulted in each
chunk's transfer over-writing the data for the first transfer. Fix
this by copying IN data as soon as it's received.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The control data toggle resets to DATA1 at the start of the data phase
of every setup transaction. We don't need a global variable to store
the value; we can just store it on the stack.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Move the body of submit_bulk_msg() into new function chunk_msg(). This
can be shared with submit_control_msg() to reduce code duplication, and
allow control messages larger than maxpacket.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
This commit allows xHCI to use both 64 and 32 bit memory
physical addresses depending on architecture it's being built for.
Also it makes use of readq()/writeq() on 64-bit systems
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Cast pointers to unsigned long instead of a sized 32-bit type to avoid
pointer to integer cast size mismatch warnings.
Cc: Tom Warren <twarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Panasonic's System LSI products, UniPhier SoC family, have been
transferred to Socionext Inc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Support xHCI host driver used on Panasonic UniPhier platform.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Because uniphier_ehci_reset() is only called from ehci-uniphier.c,
it can be a static function there.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Now UniPhier platform highly depends on Device Tree configuration
(CONFIG_OF_CONTROL is select'ed by Kconfig). Since the EHCI is only
used on main U-Boot, we can drop platform devices of the EHCI
controllers. We still keep UART platform devices because they might
be useful for SPL.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Since commit 0e7368c6c4 (kbuild: prepare for moving headers into
mach-*/include/mach), we can replace #include <asm/arch/*.h> with
<mach/*.h> so we do not need to create the symbolic link during the
build.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The dwc3_set_mode function is used only in
drivers/usb/host/xhci-exynos5.c so make it to static.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Add a driver which locates the available XHCI controllers on the PCI bus
and makes them available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Currently create_int_queue is only implemented by the ehci code, and that
does not honor interrupt intervals, but other drivers which might also want
to implement create_int_queue may honor intervals, so add an interval param.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Most of the usb-controller init code found in ehci-sunxi.c also is necessary
to init the otg usb controller, so move it to a common place.
While at it also update various #ifdefs / defines for sun8i support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Check USB Erratum A007792 applicability. If applicable, add
corresponding property in the device tree via device tree fixup
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add a new framework for fsl usb erratum handling to standardize
erratum checking only inside Uboot. Information to kernel is passed
via a boolean property corresponding to erratum, hence eliminating
need for code duplication inside kernel
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
move usb device tree fixup code from "arch/powerpc/" to "drivers/usb/"
so that it works independent of architecture it is running on
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If CONFIG_OF_CONTROL is defined, search device tree nodes that are
compatible with "panasonic,uniphier-ehci" and take the base address
from their "reg" property.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marek Vasut <marex@denx.de>
Set TXFIFOTHRESH to adjust ddr pipeline delay for successful large
usb writes
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
Move USB Errata checking code from "arch/powerpc" to architecture independent
file "fsl_usb.h" so that errata(s) become independent of the architecture.
For each erratum checking function for PPC arch, define a nop function for
non PPC arch for successful compilation in either case
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-Boot has imported various utility macros from Linux
scattering them to various places without consistency.
In include/common.h are min, max, min3, max3, ARRAY_SIZE, ALIGN,
container_of, DIV_ROUND_UP, etc.
In include/linux/compat.h are min_t, max_t, round_up, round_down,
etc.
We also have duplicated defines of min_t in some *.c files.
Moreover, we are suffering from too cluttered include/common.h.
This commit moves various macros that originate in
include/linux/kernel.h of Linux to their original position.
Note:
This commit simply moves the macros; the macros roundup,
min, max, min2, max3, ARRAY_SIZE are different
from those of Linux at this point.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
CONFIG_CPU_ARM920T was introduced into Kconfig by commit 2e07c249a6
(kconfig: arm: introduce symbol for ARM CPUs).
This commit removes all the defines of CONFIG_ARM920T and replaces the
only reference in drivers/usb/host/ohci-hcd.c with CONFIG_CPU_ARM920T.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
According to EHCI specification, the LSB of DWORD 3 of Queue Head
(Current qTD Pointer) is not T-bit, but always zero.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This change adds support for enabling the USB host features of the board.
This includes the USB3503A hub and the SMC LAN9730 ethernet controller
as well.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
usb_phy_enable should return status bit, but not phy mode bit, thus
add a new function usb_phy_mode to query the PHY for it's mode and
make usb_phy_enable just return 0 but not 'phy_ctrl & USBPHY_CTRL_OTG_ID'.
Include a new board weak function board_usb_phy_mode. If board code
does not reimplement this function, it just call usb_phy_mode and return
usb_phy_mode's return value. The reason to include such a weak function
is: " SOC OTG core <--connect--> board HOST port, but no pin id for
the board host port, so board can not use usb_phy_mode to return the
phy mode, but define it's own rule."
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
Add support for the 2 ehci controllers found on the sun6i (A31) soc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Marek Vasut <marex@denx.de>
Add proper Kconfig options to select the usb Vbus gpio-s, besides moving to
Kconfig being the right thing to do, an added advantage of this is that it
allows for boards without Vbus gpio-s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Support EHCI host driver used on Panasonic UniPhier platform.
Since Device Tree is not supported on UniPhier yet, the base address
of USB cores are passed from board files (platdevice.c).
TODO for me:
Move the base address to device trees.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
CMD_IAAD (Interrupt on Async Advance Doorbell) is bit 6, not bit 5.
While we are here, sort the flags.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
