Commit Graph

15831 Commits

Author SHA1 Message Date
Simon Schwarz
df163a5980 omap-common: Add NAND SPL linux booting
This implements booting of Linux from NAND in SPL

Related config parameters:
CONFIG_SYS_NAND_SPL_KERNEL_OFFS
	Offset in NAND of direct boot kernel image to use in SPL
CONFIG_SYS_SPL_ARGS_ADDR
	Address where the kernel boot arguments are expected - this is
	normally RAM-start + 0x100 (on ARM)

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
2012-03-27 22:05:28 +02:00
Simon Schwarz
d38bc97daf devkit8000: add config for spl command
This adds some configs for devkit8000 to use the new spl command

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
2012-03-27 22:05:28 +02:00
Simon Schwarz
1648a37505 Add cmd_spl command
This adds a spl command to the u-boot.

Related config:
CONFIG_CMD_SPL
	activate/deactivate the command
CONFIG_CMD_SPL_NAND_OFS
	Offset in NAND to use

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
2012-03-27 22:05:28 +02:00
Fabio Estevam
19db9be4aa mx53ard: Initialize return code with error
The variable "rc" is the return of board_eth_init() function. Initialize
it with an error code, so that this function can return an error when
CONFIG_SMC911X is not set.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-03-27 09:41:17 +02:00
Fabio Estevam
67ee3dd35e mx53: Make PLL2 to be the parent of UART clock
Change the parent UART clock to be PLL2, so that U-boot can also boot
a Freescale 2.6.35 kernel for mx53.

FSL kernel and U-boot changed the UART parent from PLL3 to PLL2 to avoid
conflicts with IPU clocks, so that the video resolution can be changed
without affecting the UART clock.

On a 2.6.35 kernel the serial console is messed up after IPU driver is loaded
and this patch fixes this problem.

Tested on a mx53loco board booting a FSL kernel and also a mainline kernel.

Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2012-03-27 09:41:17 +02:00
Fabio Estevam
94f0003f65 configs: imx: Use CONFIG_SF_DEFAULT_CS
CONFIG_SPI_FLASH_CS is not used anywhere.

Use CONFIG_SF_DEFAULT_CS instead.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-03-27 09:41:17 +02:00
Fabio Estevam
1fc3bbd17a mx28evk: Provide default values for SPI bus and chip select
Provide default values for SPI bus and chip select.

This allows the command "sf probe" to work without passing SPI bus and chip
select numbers as arguments.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-03-27 09:41:17 +02:00
Fabio Estevam
522b2a02e6 USB: ehci-mx6: Add proper IO accessors
Add proper IO accessors for mx6 usb registers.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>
2012-03-27 09:41:16 +02:00
Fabio Estevam
a768386746 mx6: Read silicon revision from register
Instead of hardcoding the mx6 silicon revision, read it in run-time.

Also, besides the silicon version print the mx6 variant type: quad,dual/solo
or solo-lite.

Tested on a mx6qsabrelite, where it shows:

CPU:   Freescale i.MX6Q rev1.0 at 792 MHz

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>
2012-03-27 09:41:16 +02:00
Marek Vasut
494931a674 i.MX28: Drop __naked function from spl_mem_init
Instead of compiling the function and using the result as a constant, simply use
the constant.

NOTE: This patch works around bug:

  http://gcc.gnu.org/bugzilla/show_bug.cgi?id=52546

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
2012-03-27 09:41:16 +02:00
Fabio Estevam
d9fb6a4c7e mxs_spi: Return proper timeout error
Instead of returning -1, it is preferred to return -ETIMEDOUT in case of timeouts.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-03-27 09:41:16 +02:00
Marek Vasut
a89300338a i.MX28: Make the stabilization delays shorter
Cut down the VDDIO/VDDA regulator stabilization delays to 500 uS. That should be
enough according to the datasheet and bootlets.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Robert Deliën <robert@delien.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
2012-03-27 09:41:16 +02:00
Fabio Estevam
a22429d2bf pmic_i2c: Return error in case of invalid pmic_i2c_tx_num
Return error in case of invalid pmic_i2c_tx_num.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-03-27 09:41:16 +02:00
Fabio Estevam
334bd0e225 mx6: Remove duplicate definition of ANATOP_BASE_ADDR
Remove duplicate definition of ANATOP_BASE_ADDR.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-03-27 09:41:16 +02:00
Fabio Estevam
cece262209 mx6: Fix reset cause for Power On Reset case
After booting mx6qsabrelite from POR the following is reported:

CPU:   Freescale i.MX61 family rev1.0 at 792 MHz
Reset cause: unknown reset

This is because both the POR and WDOG bits are set after reset.

Fix this by also checking both bits in the POR case.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-03-27 09:41:16 +02:00
Eric Nelson
c338f0b5c6 i.MX6: mx6qsabrelite: add MACH_TYPE_MX6Q_SABRELITE
Allow non-dt kernels to boot

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-03-27 09:41:15 +02:00
Eric Nelson
1c9ceff8ca i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAG
This is needed to support Freescale-supplied userspaces.

At the moment, both the IPU and VPU libraries provided by Freescale
in the "imx-lib" package contain routines which scrape the system
revision from /proc/cpuinfo. In the VPU library, this information is
used to load the proper firmware, allowing a single binary to be used
across various i.MX processors.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-03-27 09:41:15 +02:00
Marek Vasut
69d26d09de i.MX28: Enable additional DRAM address bits
Enables all fourteen address lines for DRAM

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
2012-03-27 09:41:15 +02:00
Eric Nelson
d928a8f3f3 mx6q: mx6qsabrelite: setup_spi() should be called in board_init to allow use for environment
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-03-27 09:41:15 +02:00
Helmut Raiger
82081406a2 mx31: add "ARM11P power gating" to get_reset_cause
Add missing reset reason 7 to get_reset_cause().

Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
2012-03-27 09:41:15 +02:00
Fabio Estevam
304e49e6cb mx31pdk: Fix CONFIG_SYS_MEMTEST_END
CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-03-27 09:41:15 +02:00
Fabio Estevam
f361a5c075 efikamx: Fix CONFIG_SYS_MEMTEST_END
CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START.

Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
2012-03-27 09:41:15 +02:00
Fabio Estevam
869aed7bce mx53smd: Fix CONFIG_SYS_MEMTEST_END
CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-03-27 09:41:15 +02:00
Fabio Estevam
bc9d5ef107 mx53evk: Fix CONFIG_SYS_MEMTEST_END
CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START.

Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-03-27 09:41:14 +02:00
Fabio Estevam
0bd14dea63 mx51evk: Fix CONFIG_SYS_MEMTEST_END
CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-03-27 09:41:14 +02:00
Eric Nelson
9ff323df76 i.MX6: mx6qsabrelite: add ext2 support
Current Ubuntu releases from Freescale contain a boot script in ext3 filesystem.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-03-27 09:41:14 +02:00
Dirk Behme
49d3e27211 imximage: Remove overwriting of flash_offset
The flash header supports different flash offsets for different
boot devices. E.g. parallel NOR or OneNAND use a different offset
than FLASH_OFFSET_STANDARD (== 0x400).

The flash offset is correctly read from the configuration in
parse_cfg_cmd(). But is then overwritten wrongly in set_imx_hdr_v1/2().

Fix this by removing this overwriting. Use the flash offset
correctly read from the configuration, instead.

If there is no flash_offset read from the configuration file, i.e.
the BOOT_FROM tag is missing, exit with an error message.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Liu <liu.h.jason@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
2012-03-27 09:41:14 +02:00
Marek Vasut
cd207cde94 IXP: Fix GPIO_INT_ACT_LOW_SET()
The GPIO_INT_ACT_LOW_SET was incorrectly handling interrupt lines higher than 7.
This is due to the fact that there are two registers for total of 16 lines.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
2012-03-26 23:09:26 +02:00
Marek Vasut
44e63c228e IXP: Fix NAND build warning on PDNB3 and SCPU
nand.c: In function ‘pdnb3_nand_read_buf’:
nand.c:107:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
nand.c: In function ‘pdnb3_nand_dev_ready’:
nand.c:124:18: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]

Remove the 4-byte-at-time read mode altogether, the most is bogus and will
likely cause unaligned accesses.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
2012-03-26 23:09:26 +02:00
Marek Vasut
2152df67c3 IXP: Move PDNB3 and SCPU from Makefile to boards.cfg
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
2012-03-26 23:09:26 +02:00
Marek Vasut
0c7857f253 IXP: Squash warnings in IXP NPE
IxEthAcc.c: In function ‘ixEthAccInit’:
IxEthAcc.c:105:21: warning: comparison between ‘IxEthDBStatus’ and ‘enum <anonymous>’ [-Wenum-compare]
IxEthDBAPISupport.c: In function ‘ixEthDBPortAddressSet’:
IxEthDBAPISupport.c:633:18: warning: variable ‘ackPortAddressLock’ set but not used [-Wunused-but-set-variable]
IxQMgrDispatcher.c: In function ‘ixQMgrLLPShow’:
IxQMgrDispatcher.c:1194:18: warning: variable ‘q’ set but not used [-Wunused-but-set-variable]

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
2012-03-26 23:09:26 +02:00
Marek Vasut
8e807ec3aa IXP: Fix missing MACH_TYPE_{ACTUX?,PNB3,DVLHOST}
These symbols are no longer defined in Linux-ARM's mach-types files. Replace
these with CONFIG_MACH_TYPE instead.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
2012-03-26 23:09:25 +02:00
Marek Vasut
696df71b5f IXP: Make IXP buildable with arm-linux- toolchains
Add -EB flag to LD to switch endianness of the linker. This should make armeb
targets buildable again. Also, make use of U-Boot's internal libgcc instead of
toolchain's one, this works around the use of libraries from GCC, which might be
little endian.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
2012-03-26 23:09:25 +02:00
Marek Vasut
e0e7f3b210 Examples: Properly append LDFLAGS to LD command
The LD command in examples/standalone/Makefile ignored platform specific
LDFLAGS setup. Pass these LDFLAGS to the command.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
2012-03-26 23:09:25 +02:00
Matt Porter
763cf0a3d2 SPL: Enable YMODEM support on BeagleBone and AM335x EVM
Cc: Chandan Nath <chandan.nath@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: Matt Porter <mporter@ti.com>
2012-03-26 23:09:25 +02:00
Matt Porter
24de357a30 SPL: Add YMODEM over UART load support
Adds support for loading U-Boot from UART using YMODEM protocol.
If YMODEM support is enabled in SPL and the romcode indicates
that SPL loaded via UART then SPL will wait for start of a
YMODEM transfer via the console port.

Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-03-26 23:09:25 +02:00
Tom Rini
71e6840279 SPL: Add README.omap3
This document describes the SPL process for OMAP3 (and related) boards
as well as a partial memory map and how to verify certain aspects
outside of running on the target.

Signed-off-by: Tom Rini <trini@ti.com>
2012-03-26 23:09:25 +02:00
Tom Rini
95579793b1 README: document more SPL config options
Signed-off-by: Tom Rini <trini@ti.com>
2012-03-26 23:09:25 +02:00
Tom Rini
ad1820a3c6 spl.c: Use __noreturn decorator
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Tom Rini <trini@ti.com>
2012-03-26 23:09:25 +02:00
Tom Rini
4a30f1e874 config.mk: Check for -fstack-usage support
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Tom Rini <trini@ti.com>
2012-03-26 23:09:24 +02:00
Tom Rini
6f4acc179c config.mk: Make cc-option create a file under include/generated
Testing for -fstack-usage requires the creation of an output file, which
isn't possible with /dev/null.

Signed-off-by: Tom Rini <trini@ti.com>
2012-03-26 23:09:24 +02:00
Tom Rini
667c9a8008 .gitignore: Add .su files
The '-fstack-usage' option to gcc will generate .su files, ignore them.

Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Tom Rini <trini@ti.com>
2012-03-26 23:09:24 +02:00
Robert Delien
56df16f25a Fix erroneous 32-bit access to hw_clkctrl_frac0 and hw_clkctrl_frac1 registers
This patch fixes erroneous 32-bit access to registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.

Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
2012-03-26 23:09:24 +02:00
Robert Delien
531bb825fd Introducing 8-bit wide register, mx28_register_8
This patch introduces an 8-bit register, mx28_register_8, in order to
prepare for fixing erroneous 32-bit wide access of registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.

Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
2012-03-26 23:09:24 +02:00
Robert Delien
b228e14e96 Renamed mx28_register to mx28_register_32 to prepare for mx28_register_8
This patch renames mx28_register to mx28_register_32 in order to
prepare for the introduction of an 8-bit register, mx28_register_8.

Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
2012-03-26 23:09:24 +02:00
Marek Vasut
40083c52f7 i.MX28: Reformat the DRAM memory configuration data
Reformat the data so it's easier to navigate through them.

Signed-off-by: Marek Vasut <marex@denx.de>
2012-03-26 23:09:24 +02:00
Marek Vasut
af335c579f M28: Support for the old M28 SoM v1.0
This prototype version SoM is unused and not available to public.
Support this only for internal debugging purposes.

Signed-off-by: Marek Vasut <marex@denx.de>
2012-03-26 23:09:24 +02:00
Marek Vasut
f5861ccc74 M28: Fix LCD PINMUX
The LCD pins configuration was wrong in U-Boot, configure pins properly.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
2012-03-26 23:09:24 +02:00
Wolfgang Grandegger
2ea73e9e38 mx6qsabrelite: add and enable USB Host 1 support
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
2012-03-26 23:09:23 +02:00
Wolfgang Grandegger
3f467529ca usb/ehci: Add USB support for the MX6Q
Currently, only USB Host 1 is supported.

Cc: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
2012-03-26 23:09:23 +02:00