Commit Graph

220 Commits

Author SHA1 Message Date
Joe Hershberger
6eed3786c6 net: Move the CMD_NET config to defconfigs
This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2015-06-01 09:40:15 -05:00
Chen-Yu Tsai
014414f536 ARM: sunxi: Enable PSCI for sun8i
sun8i uses the same PSCI backend as sun6i, without power clamps.
Since there is no secure SRAM, the backend is placed at the end
of DRAM.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-29 13:46:36 +02:00
Chen-Yu Tsai
cc08ea4cff ARM: sunxi: Enable PSCI for sun6i
Now that we have a PSCI backend for sun6i, enable it.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-29 13:46:36 +02:00
Daniel Kochmański
f76eba38b3 sunxi/nand: Add support to the SPL for loading u-boot from internal NAND memory
This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.

Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-29 13:46:36 +02:00
Hans de Goede
9d1111b70e sun9i: Add Merrii_A80_Optimus board / defconfig file
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-29 13:46:36 +02:00
Hans de Goede
1871a8ca62 sun9i: Basic sun9i (A80) support
Add initial sun9i (A80) support, only uart + mmc are supported for now.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-29 13:46:36 +02:00
Hans de Goede
93fc39a7c3 sunxi: Remove support for building "old-fashioned" fel binaries
The latest versions of the fel tool support loading normal u-boot builds
directly, and this is now the preferred way to use the fel boot method.

This commit removes support for the old deprecated standalone fel builds.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-29 13:46:36 +02:00
Paul Kocialkowski
5bfdca0d4c sunxi: VBUS detection function fixup in g_dnl_board_usb_cable_connected
sunxi_usbc_vbus_detect was renamed to sunxi_usb_phy_vbus_detect but
g_dnl_board_usb_cable_connected was still using the old name, breaking the build
when USB gadget is enabled.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-19 18:46:44 +02:00
Hans de Goede
2c68c8a409 sunxi: Add ga10h v1.1 defconfig
The ga10h is an 10" tablet with an A33 or A23 soc, 1G RAM, 8G or 16G nand,
sdio wifi, 2 micro usb ports, 1 otg and 1 host and 1 micro sd slot.

This commit adds a defconfig for the v1.1 pcb with an a33 soc.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-19 18:46:44 +02:00
Hans de Goede
8975cdf4bc sunxi: Make DRAM_ODT_EN Kconfig setting a bool
Make DRAM_ODT_EN Kconfig setting a bool, add a separate DRAM_ODT_CORRECTION
setting for A23 SoCs and use DRAM_ODT_EN Kconfig everywhere instead of
only in dram_sun4i.c and hardcoding odt_en elsewhere.

Note this commit makes no functional changes for existing boards,
its purpose is to allow changing the odt_en value on future A33 boards.

For sun4i/sun5i/sun7i boards which set DRAM_ODT_EN=y (which no defconfigs
currently do) this patch turns on odt for both the DQ and the DQS lines,
whereas previously it was possibly (but not desirable) to turn odt on only
for one of them by setting the in DRAM_ODT_EN option to 1 or 2 instead of 3.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
2015-05-19 18:46:44 +02:00
Hans de Goede
f9b08fbf11 sunxi: Set SYS_MALLOC_CLEAR_ON_INIT to n
We don't need this on sunxi, as we always use calloc or memset when
initialised memory is required. Clearing this shaves some time of our
boot time.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-19 18:37:30 +02:00
Paul Kocialkowski
9f85221135 sunxi: Pass serial number through ATAG
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-19 18:28:52 +02:00
Hans de Goede
8d837a1f7d sunxi: ehci: Convert to the driver-model
Convert sunxi-boards which use the sunxi-ehci code to the driver-model.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-14 18:49:32 -06:00
Joe Hershberger
a26cd04920 arch: Make board selection choices optional
By making the board selections optional, every defconfig will include
the board selection when running savedefconfig so if a new board is
added to the top of the list of choices the former top's defconfig will
still be correct.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Rini <trini@konsulko.com>
2015-05-12 18:10:02 -04:00
Hans de Goede
e13afeef6f sunxi: usb: Do not call phy_probe from hcd code
The 2/3 usb-phys on the sunxi SoCs are really a single separate functional
block, and are modelled as such in devicetree. So once we've moved all the
sunxi usb code to the driver-model then phy_probe will be called once
for the entire block from the driver-model enumeration code.

Move to this now as this also avoids problems with phy_probe being called
multiple times once we introduce ohci support. This also allows us to get rid
of the sunxi_usb_phy_enabled_count variable as phy_probe now is guaranteed
to be called only once.

Since we're effectively rewriting the probe / remove functions, move them
to the end of the file while we are at it, as that is the most logical place
for them.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:55 +02:00
Hans de Goede
2aacc4239c sunxi: usb: Rename the usbc.? files to usb_phy.?
The usbc.? files now only contain usb-phy related code, rename them to make
this clear.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:55 +02:00
Hans de Goede
7b798658b2 sunxi: usb: Rename sunxi_usbc_foo functions to sunxi_usb_phy_bar
Rename the sunxi_usbc_foo functions to sunxi_usb_phy_bar to make it clear
that these are usb-phy functions. Also change the verbs & nouns in the suffix
to match the verbs & nouns used in the Linux kernels generic phy framework.

This patch purely renames things, it contains no functional changes.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:55 +02:00
Hans de Goede
b6006baf9c sunxi: Move all boards to the driver-model
Now that we've everything prepared for it remove the DM settings from the
defconfig(s) and simply always set them for sunxi.

This makes all sunxi boards allways use the driver model for gpios and
ethernet, and allows us to move over more bits to the driver-model without
the need to introduce #ifdef-ery for boards which are not yet using DM.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:54 +02:00
Hans de Goede
25acd33f85 sunxi: dts: Add a CONFIG_DEFAULT_DEVICE_TREE setting to all sunxi boards
This is a preparation patch for switching all sunxi boards over to using
the driver model.

Note that rather then defining both CONFIG_DEFAULT_DEVICE_TREE (for u-boot)
and CONFIG_FDTFILE (for the kernel), this commit simply replaces all
CONFIG_FDTFILE defconfig settings with CONFIG_DEFAULT_DEVICE_TREE and
uses CONFIG_DEFAULT_DEVICE_TREE for setting the default fdtfile env value
in sunxi-common.h .

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:54 +02:00
Hans de Goede
2fcf033d36 sunxi: axp: Move axp gpio code to a separate axpi-gpio driver
Move the axp-gpio code out of the drivers/power/axp*.c code, and into
a new separate axpi-gpio driver.

This change drops supports for the gpio3 pin on the axp209, as that requires
special handling, and no boards are using it.

Besides cleaning things up by moving the code to a separate driver, as
a bonus this change also adds support for the (non vusb) gpio pins on the
axp221 and the gpio pins on the axp152.

The new axp-gpio driver gets its own Kconfig option, and is only enabled
on boards which need it. Besides that it only gets enabled in the regular
u-boot build and not for the SPL as we never need it in the SPL.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:53 +02:00
Hans de Goede
4f7e01c961 sunxi: soft-i2c: Fix gpio handling to work with the driver-model
i2c_init_board() gets called before the driver-model (gpio) code is
initialized, so move the setup of the soft-i2c pins out of i2c_init_board()
and into board_init(), at which time the driver-model setup has been done.

Also add proper error checking and properly request the gpios as that is
mandatory with the driver-model.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:52 +02:00
Hans de Goede
8760d755cb sunxi: Add Ippo_q8h_v1_2_a33_1024x600 defconfig
Add a defconfig for generic 7" tablets using the Ippo q8h v1.2 pcb,
with an A33 SoC (the pcb can take an A23 or an A33), and a 1024x600 LCD.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Vishnu Patekar
8681de3213 sunxi: Add softwinner astar mid756 A33 tablet board defconfig
The Astar MID756 is a 7" tablet using the A33 SoC with a 800x480 LCD screen,
512M RAM, 8G ROM and integrated sdio wifi.

Also see: http://linux-sunxi.org/Softwinner_astar-rda

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Vishnu Patekar
8c3dacff14 sunxi: Add basic A33 basic support
Enable full support for the A33 SoC including display, otg-usb, etc.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Hans de Goede
5e6bacdb84 sunxi: s/sun8i/sun8i_a23/
This is a preparation patch for adding A33 support, which will have a
mach name of sun8i-a33.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Hans de Goede
44d8ae5b69 sunxi: Introduce a hidden SUNXI_GEN_SUNxI Kconfig bool
sun6i and newer (derived) SoCs such as the sun8i-a23, sun8i-a33 and sun9i
have a various things in common, like having separate ahb reset control
registers, the SID living inside the pmic, custom pmic busses, new style
watchdog, etc.

This commit introduces a new hidden SUNXI_GEN_SUN6I Kconfig bool which can be
used to check for these features avoiding the need for an ever growing list
of "#if defined CONFIG_MACH_SUN?I" conditionals as we add support for more
"new style" sunxi SoCs.

Note that this commit changes the behavior of the gmac and hdmi code for
sun8i and the upcoming sun9i devices. This does not matter as sun8i does
not have gmac nor hdmi, and sun9i has new hardware-blocks for these so
the old code will not work there.

Also this is intentional as if a sun8i / sun9i variant which does use the
old hwblocks shows up then the GEN_SUN6I code paths will be the right ones
to use.

For completeness this also adds a SUNXI_GEN_SUN4I bool for A10/A13/A20.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Scott Wood
9efaca3e84 ahci: mmio_base is a virtual address
Don't store it in a u32.

Don't dereference the bus address as if it were a virtual address
(fixes 284231e49a ("ahci: Support splitting of read transactions
into multiple chunks")).

Fixes crash on boot in MPC8641HPCN_36BIT target.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Vadim Bendebury <vbendeb@chromium.org>
Acked-by: York Sun <yorksun@freescale.com>
2015-04-18 16:54:29 -04:00
Simon Glass
5b4c6f299c dm: sunxi: Support driver model for Ethernet
Adjust the Ethernet initialisation code to support driver model.
It is no-longer necessary to call designware_initialize(). The device will
be probed when it is used. The PHY type and GMAC base will come from the
device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:37 -06:00
Paul Kocialkowski
6c739c5d8a sunxi: Complete i2c support for each supported platform
Sunxi platforms come with at least 3 TWI (I2C) controllers and some platforms
even have up to 5. This adds support for every controller on each supported
platform, which is especially useful when using expansion ports on single-board-
computers.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:33:17 +02:00
Paul Kocialkowski
1847c1da02 sunxi: iNet 3F support
The iNet 3F is an A10 tablet with 1GiB RAM and a 1024x768 screen.

Also see: http://linux-sunxi.org/INet_3F

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:33:17 +02:00
Paul Kocialkowski
96fc68c2d5 sunxi: iNet 3W support
The iNet 3W is an A10 tablet with 1GiB RAM and a 1024x768 screen.

Also see: http://linux-sunxi.org/INet_3W

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:33:17 +02:00
Paul Kocialkowski
1d1bce8733 sunxi: Proper iNet board config naming
The official name for the iNet manufacturer is iNet with a lowercase i and an
uppercase N.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:33:17 +02:00
Paul Kocialkowski
8e2fc523a9 sunxi: Removed dram files cleanup in MAINTAINERS
A few dram files were still listed as maintained even though they were removed
some time ago

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:33:17 +02:00
Paul Kocialkowski
8c8165739b sunxi: Serial number support, obtained from SID bits
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:18 +02:00
Paul Kocialkowski
849d597bac sunxi: Yones Toptech BD1078 support
The Yones Toptech BD1078 is an A20 based 10" tablet with a 1024x600 lcd screen,
volume up/down and back buttons, headphones jack, mini hdmi, micro usb (otg),
micro usb (host), external micro-sd slot and a separate internal micro-sd slot.

Also see: http://linux-sunxi.org/Yones_Toptech_BD1078

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
8deacca975 sunxi: Complete mmc pin mux for each supported platform, configured with Kconfig
Sunxi platforms have different possible mmc pin mux setups (except for mmc0),
which are different across platforms.

This lets users configure which is used through the CONFIG_MMC*_PINS Kconfig
options. This is especially relevant when a second (in addition to mmc0) port
is used and CONFIG_MMC_SUNXI_SLOT_EXTRA is enabled.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
487b3277d4 sunxi: GPIO pin mux hardware-feature-specific function index defines
Each hardware feature exposed through the GPIO pin mux is usually using the same
function index (for a given port), so there is no need to define one value per
pin: one value per hardware feature per port is sufficient, avoids duplication
and makes everything easier to understand.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
81f11872f3 sunxi: Ainol AW1 support
The Ainol AW1 is an A20 based tablet with a 800x480 lcd screen, sdio wifi,
volume up/down and home buttons, micro-sd slot, micro usb (otg), headphones
connector and a SPCI modem connector.

Also see: http://linux-sunxi.org/Ainol_AW1

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
f1df758d30 sunxi: USB download gadget cable detection
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
ebd468b2d2 sunxi: common VBUS detection logic in usbc
VBUS detection could be needed not only by the musb code (to prevent host mode),
but also by e.g. gadget drivers to start only when a cable is connected.

In addition, this allows more flexibility in vbus detection, as it could easily
be extended to other USBC indexes. Eventually, this would help making musb
support independent from a hardcoded USB controller index (0).

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Han Pengfei
d3aa051e7a sun6i: Add support for the Mixtile LOFT-Q board
The Mixtile LOFT-Q is an A31 based board with 2G RAM, 8G EMMC, sdio wifi,
1Gbit ethernet, HDMI display, toslink audio plug, 4 USB2.0 port, external
USB2SATA connector, sd card plug, 3x60 external fpic expansion connector,
NXP JN5168 zigbee gw, remote support.

Also see http://focalcrest.com/en/pc.html#pro02

Signed-off-by: Han Pengfei <pengphei@sina.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Hans de Goede
662e2acb46 sunxi: UTOO_P66: Add missing MAINTAINERS entry
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-29 14:56:48 +02:00
Iain Paton
e71b422bd7 sunxi: use CONFIG_SYS_CLK_FREQ to set cpu clock
make the CPU clock selectable via Kconfig

this removes the sunxi specific CONFIG_CLK_FULL_SPEED defined in each
soc header and replaces it's use in board/sunxi/board.c with
CONFIG_SYS_CLK_FREQ from Kconfig which allows us to configure board
specific frequency on boot

Signed-off-by: Iain Paton <ipaton0@gmail.com>
[hdegoede@redhat.com s/CONFIG_SYS_CLK_FREQ/CONFIG_TIMER_CLK_FREQ/ for the
 arch-timer clk speed on sun7i to fix mis-compile on sun7i]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-29 13:36:03 +02:00
Hans de Goede
1fc42018a0 sunxi: video: Fix VIDEO_LCD_PANEL_I2C being enabled by default
Fix a typo in board/sunxi/Kconfig which caused VIDEO_LCD_PANEL_I2C to be
enabled on all sunxi boards. Also fix a compile error which shows up once
VIDEO_LCD_PANEL_I2C is actually disabled on most boards as it should be.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10 15:20:25 +01:00
Aleksei Mamlin
b4db74cfd0 sunxi: Add Wexler TAB7200 support
This patch add support for Wexler TAB7200 tablet.

The Wexler TAB7200 is a A20 based tablet with 7 inch display(800x480),
capacitive touchscreen(5 fingers), 1G RAM, 4G NAND, micro SD card slot,
mini HDMI port, 3.5mm audio plug, 1 USB OTG port and 1 USB 2.0 port.

Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10 15:20:25 +01:00
Hans de Goede
5112703fdd sun7i: Add support for the Orange Pi Mini board
The Orange Pi Mini is an A20 based development board featuring 1G RAM, HDMI,
1Gbit ethernet, USB wifi, SATA, 2 sdcard slots (use the top one for booting),
2 USB 2.0 A receptacles, a micro USB B receptacle (otg) and a 3 ring 3.5 mm
jack connector for A/V.

Also see: http://www.orangepi.org/

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10 15:20:24 +01:00
Hans de Goede
9ad4c227ee sun7i: Add support for the Orange Pi board
The Orange Pi is an A20 based development board featuring 1G RAM, HDMI & VGA,
1Gbit ethernet, USB wifi, SATA, 4 USB 2.0 A receptacles, a micro USB B
receptacle (otg) and a 3 ring 3.5 mm jack connector for A/V.

Also see: http://www.orangepi.org/

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10 15:20:24 +01:00
Hans de Goede
9ee54858e4 sun7i: Add support for the Wits Pro A20 DKT board
The Wits Pro A20 DKT is an A20 Development KiT with 1G RAM, 4G NAND, sdio wifi,
1Gbit ethernet, 1024x768 lcd screen with ft5x_ts touchscreen and a ton of
IO connectors.

Note there seem to be multiple sdcard slots on the board (4 in total), but
other then mmc0 none of these are hooked up by default, there is a ton of
dip-switches which likely allow hooking some of these up, but the documentation
of the board only describes the use of a fraction of them, so for now we
only support mmc0.

Also see: http://www.merrii.com/en/pla_d.asp?id=163

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10 15:20:24 +01:00
Jens Lucius
25dab88fe9 sunxi: Add support for the Forfun Q88DB tablet
The Forfun Q88DB is an A13 tablet in the common Q8 format.

Features are 512MB RAM, 4GB NAND, 7" Display, RTL8188 Wifi, 2 cameras.

For more details see: http://linux-sunxi.org/Forfun_Q88DB

Signed-off-by: Jens Lucius <info@jenslucius.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10 15:20:24 +01:00
Marcus Cooper
44857532cf sun6i: Add support for the Mele I7 board
The Mele I7 is a Allwinner based Android TV box.

It features a A31 SOC, 1G RAM, 8GB NAND, HDMI out, A/V out,
SPDIF, IrDA, 3 USB A, 1 USB micro OTG and Wireless LAN.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10 15:20:24 +01:00
Marcus Cooper
5516d5ca9b sun7i: Add support for the MK808C board
The MK808C is a Allwinner based Android TV dongle.

It features a A20 SOC, 1G RAM, 8GB NAND, HDMI out, A/V out,
1 USB A, 1 USB mini OTG, Bluetooth and Wireless LAN.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10 15:20:24 +01:00
Gábor Nyers
a4f1734edf sunxi: Add support for the Jesurun Q5 board
The Jesurun Q5 has a black plastic casing with the approximate dimensions of
100mm x 100mm x 24mm with rounded edges. In terms of hardware it features an
Allwinner A10 SoC with 1GB RAM and 8GB of NAND flash. The storage capacity can
be extended up to 32GB with a MicroSD card. The external connectors are: 2x
USB-A female supporting USB2.0, 3.5mm female jack for audio, HDMI female,
SPDIF, RJ45 LAN and Power. In addition the device has 1x red LED (hard wired to
power) and an programmable green led. On the board there is also an unpopulated
IR receiver and the UART. The devices is equipped with an AXP209 PMU.

For more details see: http://linux-sunxi.org/Jesurun_Q5

Signed-off-by: Gábor Nyers <gnyers@opensuse.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10 15:20:24 +01:00
Adam Sampson
8d6e18df60 sunxi: Make CONFIG_DRAM_TPR3 apply to sun[57]i
The tpr3 (timing skew) parameter is used in all supported versions of
the sunxi DRAM controller, but it was only enabled for sun4i in
47e3501a76.

Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10 15:20:23 +01:00
Hans de Goede
52defe8f65 sunxi: musb: Check Vbus-det before enabling otg port power
Sending out 5V when there is a charger connected to the otg port is not a
good idea, so check for this and error out.

Note this commit currently breaks otg support on the q8h tablets, as we need
to do some magic with the pmic there to get vbus info, this is deliberate
(better safe then sorry), fixing this is on my TODO list.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-21 16:53:33 +01:00
Hans de Goede
aad2ac24c0 sunxi: video: Add support for tl059wv5c0 lcd panels
Add support for the 6" 480x800 tl059wv5c0 panel used on e.g. Utoo P66 and
Aigo M60/M608/M606 tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-20 08:11:57 +01:00
Hans de Goede
55410089cb sunxi: video: Add support for LCD panels which need to be configured via i2c
This commits adds support for configuring a a bitbang i2c controller, which
is used on some boards to configure the LCD panel (via i2c).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-20 08:11:57 +01:00
Hans de Goede
242e3d893d sunxi: video: Add support for LCD reset pin
On some boards there is a gpio to reset the LCD panel, add support for this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-20 08:11:57 +01:00
Simon Glass
942cb0b6a2 sunxi: Normalise FEL support
Make sunxi's FEL code fit with the normal U-Boot boot sequence instead of
creating its own. There are some #ifdefs required in start.S. Future work
will hopefully remove these.

This series is available at u-boot-dm, branch sunxi-working.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-16 20:15:09 +01:00
Hans de Goede
8910a7d37a sunxi: MAINTAINERS: drop no longer existing felconfig-s from MAINTAINERS
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-16 19:40:59 +01:00
Paul Kocialkowski
e8f768ab33 sunxi: Ampe A76 support
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-16 19:40:59 +01:00
Siarhei Siamashka
47e3501a76 sunxi: dram: Support more sun[457]i dram parameters in Kconfig
This patch allows to configure all the important DRAM parameters in Kconfig.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02 14:04:23 +01:00
Siarhei Siamashka
d133647af4 sunxi: dram: Optionally use standard JEDEC timings for sun[457]i
In addition to the current Android magic settings, allow to optionally use
DDR3 timing parameters, which are tailored for different clock frequencies
and JEDEC speed bins. This should improve reliability and performance.

Adding '+S:CONFIG_DRAM_TIMINGS_DDR3_1066F_1333H=y' to the board defconfig
allows to use timings, which are calculated for the DDR3-1066F speed bin.
A lot of DDR3 chips, which are used in real Allwinner based devices,
support DDR3-1066F speed bin timings.

And adding '+S:CONFIG_DRAM_TIMINGS_DDR3_800E_1066G_1333J=y' should work
with any DDR3 chips, because this targets the slowest JEDEC speed bins.

The vendor magic values are still used by default for DRAM, but board
maintainers now have more flexibility in DRAM timings selection.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02 14:04:15 +01:00
Hans de Goede
fb75d972ea sunxi: video: Force h/vsync active high when using ext. vga dac on some boards
On both my A13-OLinuxIno and my A13-OLinuxIno-Micro, the vga output gives an
unstable image when active low v or hsync is used.

The problem seems to be specific to the OLinuxIno A13 (normal & micro)
boards. I've just looked up the schematics and they use an opendrain driver
for the vga sync lines, and with sync pulses it is the logical high->low
edge of the pulse which counts for the timing, which with an active low
sync is being driven by the pull-up, and that simply seems to not drive
it hard enough to get a stable image.

So force v and hsync active high on these boards. independent of what the
modeline says. This fixes the unstable image.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02 13:57:16 +01:00
Michal Suchanek
8d0df9be92 sunxi: Add Inet 86VS support
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02 13:57:16 +01:00
Paul Kocialkowski
29dd7d8c20 sunxi: TZX-Q8-713B7 support
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02 13:57:16 +01:00
Adam Sampson
00f120bd61 sunxi: Add Linksprite_pcDuino3_Nano board / defconfig
This is a low-cost Allwinner A20 board with Arduino-style GPIO headers;
it features 1G RAM, 4G NAND flash, 1 micro-SD, 2 USB sockets, 1 micro
USB socket for OTG and another for power in, HDMI, SATA, 5V power for
SATA devices, gigabit Ethernet, an IR receiver, 3.5mm audio out and a
MIPI camera connector.

Like the BananaPi, this board needs GMAC_TX_DELAY set to 3 in order for
GMAC to work reliably at gigabit speeds.

For more details, see: http://linux-sunxi.org/LinkSprite_pcDuino3_Nano

Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02 13:56:19 +01:00
Hans de Goede
11dfef07d9 sunxi: MAINTAINERS: sort entries alphabetically
Keep all entries except for the monster entry at the top alphabetically sorted.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02 13:55:14 +01:00
Hans de Goede
40d0cdda3e sunxi: Remove CONFIG_TARGET_FOO for sun5i and sun7i boards
CONFIG_TARGET_FOO was only used in board/sunxi/Makefile to select the
dram config for sun5i and sun7i boards and in board/sunxi/gmac.c for some
special handling of the bananapi/bananapro (both sun7i), all sun5i and sun7i
boards have been moved over to using a single dram_sun5i_autoconfig file,
and the tx clk delay handling for the Banana boards now has its own Kconfig.

IOW nothing is using CONFIG_TARGET_FOO anymore, so remove it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02 13:55:14 +01:00
Hans de Goede
c13f60d92a sunxi: Add a GMAC Transmit Clock Delay Chain Kconfig option
And use this to set the GMAC Transmit Clock Delay Chain value on Banana
boards, rather then keying of CONFIG_TARGET_FOO.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02 13:55:14 +01:00
Hans de Goede
e1a0888ed2 sunxi: Convert sun5i boards to use auto dram configuration
Currently we've separate detailed dram settings for all sun5i boards, this
moves them over to using auto dram configuration so that we can get rid of
all the per board dram_foo.c files.

This has been tested on a A10s-Olinuxino, A13-Olinuxino, A13-OlinuxinoM,
mk802-a10s and r7-tv-dongle board.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02 13:55:14 +01:00
Hans de Goede
faffd4a5cb sunxi: Add Hyundai A7HD support
The Hyundai A7HD is a 7" 16:9 A10 powered tablet featuring 1G RAM, 8G
nand, 1024x600 IPS screen, a mini hdmi port, mini usb receptacle and a
headphones port for details see: http://linux-sunxi.org/Hyundai_A7HD

Cc: Mark Janssen <maniac@maniac.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-23 15:15:11 +01:00
Hans de Goede
a7403ae84d sunxi: video: Make pwm polarity configurable
It turns out that there are some panels where the pwm input is not active low,
so make it configurable.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-23 15:15:02 +01:00
Ian Campbell
c17fb11c56 sunxi: Add support for Mele M5.
HDMI, SATA, USB and Ethernet appear functional, I've not done extensive tests
of all peripherals though.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-23 15:15:02 +01:00
Hans de Goede
389046be2f sunxi: Convert sun7i boards to use auto dram configuration
Currently we've separate detailed dram settings for all sun7i boards, this
moves them over to using auto dram configuration so that we can get rid of
all the per board dram_foo.c files.

This has been tested on a A20-Olinuxino-Lime, A20-Olinuxino_MICRO, Bananapi,
Bananapro, Cubieboard2, Cubietruck, Mele_M3 and a Linksprite_pcDuino3.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-23 15:15:02 +01:00
Hans de Goede
56333be9b2 sunxi: Drop qt840a_defconfig
The qt840a is one of the many tv-boxes using the "i12" A20 pcb, but it
populates only one of the 2 places for a 16 bit dram ic, thus reducing
the buswidth to 16 bits, and the amount of ram to 512M, which is why we
had a separate config for it.

This commit switches the generic i12-tvbox_defconfig over to DRAM
autoconfiguration, so that it will work with the qt840a too, and drops the
qt840a specific config, like we've done with other memory-amount specific
configs before.

Tested on a generic i12-tvbox with 32 bit bus-width / 1G RAM, and on a
qt840a with 16 bit bus-width / 512M RAM.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-23 15:15:02 +01:00
Hans de Goede
89c95b0811 sunxi: Add new Chuwi V7 CW0825 board / defconfig
The Chuwi V7 is an A10 (sun4i) based tablet with 1G of RAM, 16G of nand flash,
microsd slot, 7" 1024x768 lvds ips panel, mini hdmi out, headphones out,
stereo speakers, front & back camera and usb wifi.

It is clearly marked "CHUWI", "V7" and "Model: CW0825" on the back of the
tablet.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-23 15:15:02 +01:00
Hans de Goede
27515b20c1 sunxi: video: Add support for Hitachi tx18d42vm LVDS LCD panels
Add support for Hitachi tx18d42vm LVDS LCD panels, these panels have a
lcd controller which needs to be initialized over SPI, once that is
done they work like a regular LVDS panel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-23 15:14:53 +01:00
Hans de Goede
1a800f7af3 sunxi: Hookup OTG USB controller support
Hookup OTG USB controller support and enable the otg controller + USB-keyb
on various tablets.

This allows tablet owners to interact with u-boot without needing to solder
a serial console onto their tablet PCB.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:56 +01:00
Priit Laes
ea87948f1a sunxi: Add Gemei G9 (Allwinner A10/sun4i) tablet
Gemei G9 is an A10 based tablet, with 1G RAM, 16G NAND, 1024x768
IPS LCD display, stereo speakers, 1.3MP front camera and 5 MP
rear camera, 8000mAh battery, GT901 2+1 touchscreen, Bosch BMA250
accelerometer and RTL8188CUS USB wifi. It also has MicroSD slot,
miniHDMI, 1 x MicroUSB OTG port and 1 x MicroUSB host port and
3.5mm headphone jack.
More details are available at: http://linux-sunxi.org/Gemei_G9

Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-22 12:34:56 +01:00
Aleksei Mamlin
1cf054a883 sunxi: Add Marsboard A10 support
This patch add support for Marsboard A10 board.

The Marsboard A10 is a A10 based development board with 1G RAM, 1G NAND,
micro SD card slot, SATA 2.0 socket, 10/100 ethernet, mini HDMI port,
1 USB OTG port and 2 USB 2.0 ports. Board does not use the AXP209 pmic,
it does not have a pmic at all.
Board also have 2 expansion 70 pin headers.

Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-22 12:34:56 +01:00
Siarhei Siamashka
97ece830ec video: sunxi: Hook up SSD2828 with the sunxi video driver
Convert GPIO names from Kconfig strings into pin numbers for
the 'ssd2828_config' struct. Add SSD2828 initialization between
enabling the parallel LCD interface and turning on the backlight.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-22 12:34:56 +01:00
Siarhei Siamashka
6906df1ab8 sunxi: axp221: Add ELDO[1-3] support
And also add Kconfig option for selecting ELDO3 voltage. The reason
for having this option is that the Android kernel sets ELDO3 to
1.2V when powering up LCD in the case if 'lcd_if' configuration
variable is set to 6 (LCD_IF_EXT_DSI) in the FEX file. Most likely
to supply power for a SSD2828 chip.

However on the MSI Primo81 tablet, which is using this particular
'lcd_if = 6' setup for LCD, setting the ELDO3 voltage appears to
be unnecessary and it works regardless. Having no schematics of
this tablet, I can only guess that 1.2V is supplied to SSD2828
in some other way.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-22 12:34:56 +01:00
Hans de Goede
6c46c8e890 sunxi: Add mk802_a10s board / defconfig
The mk802_a10s re-uses is the "classic" mk802 case and functionality, but has
an A10s SoC inside rather then the A10, it features 512M or 1G RAM, 4G nand,
a mini-hdmi female connector, USB-A receptacle, mini-usb receptacle (OTG)
and a sdio realtek wifi chip. Unlike the original mk802 it does have a pmic,
the axp152.

For more details see: http://linux-sunxi.org/Semitime_g2

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:56 +01:00
Hans de Goede
3a1c223f19 sunxi: Add mk802ii board / defconfig
The mk802ii is a revised version of the mk802 A10 based hdmi tv-stick, it
features 1G RAM, 4G nand, a hdmi male connector, USB-A receptacle, 2 micro
usb receptacles (OTG & power) and USB-wifi, and does come with an axp209 pmic.

For more details see: http://linux-sunxi.org/Rikomagic_mk802ii

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:56 +01:00
Hans de Goede
88b46d4baf sunxi: Add mk802 board / defconfig
The mk802 is the "classic" Allwinner A10 based hdmi tv-stick, it features
512M or 1G RAM, 4G nand, a mini-hdmi female connector, USB-A receptacle,
mini-usb receptacle (OTG) and USB-wifi. Somewhat unique the mk802 does not
use the AXP209 pmic, it does not have a pmic at all.

For more details see: http://linux-sunxi.org/Rikomagic_mk802

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:56 +01:00
Hans de Goede
6915270871 sunxi: Remove CONFIG_TARGET_FOO for sun4i, sun6i and sun8i boards
CONFIG_TARGET_FOO is only used in board/sunxi/Makefile to select the
dram config for sun5i and sun7i boards and in board/sunxi/gmac.c for some
special handling of the bananapi/bananapro (both sun7i), iow it is not used
at all on any sun4i, sun6i and sun8i boards so lets get rid of it there.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:56 +01:00
Hans de Goede
2ddd8012f5 sunxi: Convert sun4i boards to use auto dram configuration
Currently we've separate detailed dram settings for all sun4i boards, this
moves them over to using auto dram configuration so that we can get rid of
all the per board dram_foo.c files.

Tested-by: Hans de Goede <hdegoede@redhat.com> on a A10-OLinuXino-Lime,
 Chuwi_V7_CW0825 and ba10_tv_box
Tested-by: Zoltan HERPAI <wigyori@uid0.hu> on a pcduino
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:56 +01:00
Hans de Goede
8ffc487c75 sunxi: Stop differentiating between 512M and 1G variants of the same board
While working on adding more boards I noticed that we lack a config for
the 512M cubieboard, and that some of the new boards which I want to add also
have 512M and 1G variants, rather then adding 2 defconfig's for all of these,
lets switch the exising boards which have both a 512M and 1024M variant over
to the sun4i dram autoconfig code.

This also drops the foo_RAMSIZE_defconfig variants of boards where we currently
have 2 separate configs already.

Note:
1) The newly introduced CONFIG_DRAM_EMR1 kconfig value is not used with
a value other then its default for now, but we need this to be configurable
to support some new boards with auto dram config.

2) We always set all CONFIG_DRAM_foo values in defconfigs, even if they match
the defaults, this is done to make it more clear what values are used for a
certain board.

This has been tested on a Mele A1000, Mini-X and a Cubieboard, all 1G
variants, the dram autoconfig code has also been tested on a 512M mk802
(a defconfig for the mk802 is added in a later patch).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:56 +01:00
Hans de Goede
6515032e3b sunxi: display: Make lcd display clk phase configurable
While running some tests with an Olinuxino-A13-Micro + a 7" Olimex LCD module
I noticed that the screen flickered. This is caused by the lcd display clk
phase reg value being set to 0, where it should be 1 in this setup.

This commit adds a Kconfig option for the lcd display clk phase, so that we
can set it per board. This defaults to 1, because looking at all the fex
files in sunxi-boards, that is by far the most used value.

This commit updated the Ippo and MSI Primo73 tablet defconfigs to override the
default of 1 with 0, as that is the correct value for those tablets, this
keeps the register settings the same as before this commit.

The Olinuxino-A13 defconfigs are not updated, changing the register setting
for these boards from 0 to 1, this is intentional.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:55 +01:00
Hans de Goede
4458b7a6e1 sunxi: usbc: Add support for usb0 to the common usbc code
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:40 +01:00
Chen-Yu Tsai
507e27dfc9 sunxi: video: Add support for external DAC enable pin
The external DAC for VGA output might have either a power or reset
control pin that needs to be pulled up, as is the case on the
Hummingbird A31.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14 14:56:40 +01:00
Chen-Yu Tsai
2583d5b192 sunxi: video: Allow external DACs for VGA on platforms without TV encoders
Using an external DAC for VGA output was available on sun5i. Since
some other SoCs don't have a builtin TV encoder, but might have
use for a VGA output, enable the option for the platforms that
don't have TV encoders.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14 14:56:40 +01:00
Hans de Goede
213480e12d sunxi: video: Add lvds support
Add support for lvds lcd panels

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:40 +01:00
Zoltan HERPAI
213dcbfdeb sunxi: add Linksprite pcDuino v1/v2 support
Add support for a sun4i board built by Linksprite. This addition covers
both v1 and v2 versions. As the board has been working with 408MHz memory
setting in the u-boot-sunxi branch, and has been proven to be running stable
during my tests as well, a respective new DRAM config file is added as well.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14 14:56:39 +01:00
Hans de Goede
d9786d2380 sunxi: video: Add VGA output support
Add support for VGA directly from the sunxi SoC / display engine.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
e2bbdfb1e3 sunxi: video: Add support for VGA via external DACs connected to the LCD pins
Add support for external DACs connected to the parallel LCD interface driving
a VGA connector, such as found on the Olimex A13 boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
2fbf091a54 sunxi: video: Enable video on sun8i, which supports LCD but not HDMI
The A23 (sun8i) only has lcd output support, so allow building the video code
without HDMI support for use with the A23.

Also the A23 has the same reset bits (and necessity to enable the DRC block)
as the sun6i, so enable those bits for sun8i too.

Note building without HDMI support is useful for the A13 (sun5i variant) too,
as that one does not have HDMI either.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
2dae800f1e sunxi: video: Add lcd output support
Add lcd output support, see the new Kconfig entries and doc/README.video for
how to enable / configure this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
81ec100151 sun7i: Add new Bananapro board / defconfig
Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Siarhei Siamashka
f4f0df09b9 sun7i: Add defconfig for MSI Primo73 tablet
This patch uses the same DRAM settings as in the pre-installed
Android firmware. The LCD display is supported too.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14 14:56:37 +01:00