This is not required. The MMC core sends CMD0 right after the
initialization and it serves the same purpose.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
It sometimes happen that the PSTATE register does not indicate that the
bus is ready when it really is. This usually happens after a mode switch.
In that case it makes sense to reset the FSM handling the CMD and DATA
Also reset the FSMs if the STATE register cannot be cleared. This also
sometimes happens after a mode switch.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The response type of CMD25 is R1 instead of R1b.
Signed-off-by: Akio Hirayama <hirayama.akio@socionext.com>
[masahiro: add log ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Card detect function implemented for SDHCI framework.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch reads cd-gpio property from devicetree
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch reads card detect properties from device tree &
added mmc capability macros in mmc.h.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When MMC_TINY is enabled, support for only one MMC device
is provided. Boards that register more than one device,
will just write over mmc_static keeping only the last one
registered.
This commit prevents this, keeping only the first MMC
device created. A debug warning message is added, if nothing
else, as a hint/documentation for developers.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
The SPL_MMC_TINY implements feature-reduced MMC support
on SPL, and as such, it's more consistent and convenient
to find it as part of the SPL configuration.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
The fsl_esdhc driver was for Freescale eSDHC on MPC83XX/MPC85XX
initially. The later QoriQ series PowerPC processors (which were
evolutions of MPC83XX/MPC85XX), QorIQ series ARM processors, and
i.MX series processors were using this driver for their eSDHCs too.
For the two series processors, the eSDHCs are becoming more and
more different. We should have split it into two drivers, like them
(sdhci-of-esdhc.c/sdhci-esdhc-imx.c) in linux kernel.
This patch is just to create a fsl_esdhc_imx driver which is a copy
of fsl_esdhc driver for i.MX processors. We will convert i.MX processors
to use fsl_esdhc_imx, and clean up the two drivers separately in the
future patches.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
u-boot is trying to make CONFIG_BLK as a hard requirement
for DM_MMC. But now it's still not.
config BLK
bool "Support block devices"
depends on DM
default y if DM_MMC
When fsl_esdhc driver was reworked for DM_MMC support, DM_MMC
without CONFIG_BLK enabled wasn't considered. This patch is to
fix probe issue without CONFIG_BLK enabled.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
U-Boot code currently only applies this restriction to HS200 mode,
extend this to HS400 mode as well.
Currently U-Boot code not support accessing boot partition in HS200/400
mode. This needs more check.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
For bcm7445 and bcm7260, this patch enables CONFIG_DM_MMC and updates
the bcmstb SDHCI driver to use the new driver model. This allows
removal of SDHCI configuration handling from bcmstb.c, and eliminates
a board removal compile warning.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- Gen3 PCIe driver + enablement on Salvator-X platforms.
- Gen3 recovery SPL used to reload ATF/OpTee/U-Boot instead of minimon.
- SDHI HS400 fixes ported from latest BSP and datasheet.
PowerPC supports 32 bit address.
So adopt 32 bit addr in fsl_esdhc for CONFIG_PPC.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Since Gen3 SDHI has an internal DS signal AC-spec violation in HS400 mode,
CRC-error may occur in read command in HS400 mode. This phoenomenon occurs
at low/high temperature.
To fix this, after completion of HS400 tuning, enable manual calibration.
However, Gen3 M3 Ver.1.2 or earlier and H3 1.x does not support HS400.
These SoC forcibly use HS200 mode by SoC attribute.
The DT adjustment of the tuning parameters is not supported until the
DT property names become clear.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Adapted from a patch by Takeshi Saito <takeshi.saito.xv@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Peng Fan <peng.fan@nxp.com>
Clean up the whitespaces in macros, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Peng Fan <peng.fan@nxp.com>
This reverts commit 72a89e0da5, which
causes the imx53 HSC to hang as the eMMC is not working properly anymore.
The exact error message:
MMC write: dev # 0, block # 2, count 927 ... mmc write failed
0 blocks written: ERROR
imx53 is not using the DDR mode.
Debugging of pre_div and div generation showed that those values are
generated in a way, which is not matching the ones from working setup.
As the original patch was performing code refactoring, let's revert this
change, so all imx53 boards would work again.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_BOOT
As requested by Michal Simek <michal.simek@xilinx.com>, these boards
have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:
xilinx_zynqmp_zc1275_revB
xilinx_zynqmp_zc1751_xm018_dc4
xilinx_zynqmp_zc1751_xm019_dc5
xilinx_zynqmp_zcu100_revC
xilinx_zynqmp_zcu102_rev1_0
xilinx_zynqmp_zcu102_revA
xilinx_zynqmp_zcu102_revB
xilinx_zynqmp_zcu104_revA
xilinx_zynqmp_zcu104_revC
xilinx_zynqmp_zcu106_revA
xilinx_zynqmp_zcu111_revA
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
The Standard Host Controller Interface (SDHCI) specification version
3.00 adds support for Advanced DMA (ADMA) for both 64 and 32 bit widths
of DMA. ADMA2 uses a table of descriptors for aggregating DMA requests.
This significantly improves read and write throughput.
Add Support for the same.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
In preparation for addition of ADMA2 support, cleanup SDMA handling by
moving it to a new sdhci_prepare_dma() function. Also add a flags field
in sdhci_host to indicate if DMA is enabled.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The wp-gpios property is used for gpio, if this is set, the WP pin is muxed
to gpio function, can't be used as internal WP checking. However the codes
remain to use internal WP checking.
This patch changes to examine the "fsl,wp-controller" for enabling internal WP
checking, and "wp-gpios" for muxing to gpio.
Signed-off-by: Ye Li <ye.li@nxp.com>
When sd/mmc work at DDR mode, like HS400/HS400ES/DDR52/DDR50 mode,
the output clock rate is half of the internal clock rate.
This patch set the DDR_EN bit first for DDR mode, hardware divide
the usdhc clock automatically, then follow the original sdr clock
setting method.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The driver currently calculates the end address of cache flush operation
for the DMA descriptors by adding cacheline size to the start address of
the last DMA descriptor. This is not safe, as the cacheline size may be,
in some unlikely cases, smaller than the DMA descriptor size. Replace the
addition with roundup() applied on the end address of the last DMA
descriptor to round it up to the nearest cacheline size multiple.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
The bounce_buffer_start() can return -ENOMEM in case memory allocation
failed. However, in that case, the bounce buffer address is the same as
the possibly unaligned input address, and the cache maintenance operations
were not applied to this address. This could cause subtle problems. Add
handling for the bounce_buffer_start() return value to prevent such a
problem from happening.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
The current 4-minute data transfer timeout is misleading and broken.
Instead of such a long wait, calculate the timeout duration based on
the length of the data transfer. The current formula is the transfer
length in bits, divided by a multiplication of bus frequency in Hz,
bus width, DDR mode and converted the mSec. The value is bounded from
the bottom to 1000 mSec.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
The new DM implementation currently does not support the Sheeva
88SV331xV5 specific quirk present in the legacy implementation. The
legacy code is thus kept for this SoC and others not yet migrated to
DM_MMC.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
We either need to use IS_ENABLED(CONFIG_FOO) or CONFIG_IS_ENABLED(FOO).
IS_ENABLE(FOO) will always return false.
This commit fixes the comparison by using the CONFIG_IS_ENABLED(FOO)
syntax.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Some MediaTek SoC need an additional clock "source_cg". Enable
this new clock. We reuse the same clock name as in the kernel.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
On response type r1b, if DTIME is not defined or too short,
the Datatimeout and DPSM flag occurs. Like the DPSM is
activated all next data transfer will be frozen.
To avoid this freeze:
-The driver must define a DTIME on all r1b response type.
-DTIME of SDMMC must be defined for alls stop transmission
(for read and write request) even if MMC_RSP_BUSY is not set.
-If busy timeout occur, an abort request must be sent to
reinitialize the DPSM.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Initially the compatible string was wrongly set to "st,stm32f4xx-sdio".
Use compatible string used by kernel instead and identify mmci variant
using "arm,primecell-periphid" property.
Currently, the DM part of mmci driver is only used by STM32 SoCs,
that's why the switch case gets only one entry. It will be populated
easily with new variant in the future.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add the DM_MMC-compatible DesignWare MMC driver support for Synopsys
ARC devboards. It is created to switch ARC devboards to use DM_MMC.
It required information such as clocks (Bus Interface Unit clock,
Card Interface Unit clock) and SDIO bus width.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Pbias voltage should match the IO voltage set for the SD card. With the
latest pbias change to 3.3V, update the capabilities and IO voltages
settings to 3.3V.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
After the commit b9a2a0e2e9 ("mmc: Add support for downgrading
HS200/HS400 to HS mode"), it add a parameter in mmc_set_card_speed()
which indicates that the HS200/HS400 to HS downgrade is happening.
During the HS400 initialization, first select to HS200, and config
the related clock rate, then downgrade to HS mode. So here also need
to config the downgrade value to be true for two reasons. First,
make sure in the function mmc_set_card_speed(), after switch to HS
mode, first config the clock rate, then read the EXT_CSD, avoid
receiving data of EXT_CSD in HS mode at 200MHz. Second, after issue
the MMC_CMD_SWITCH command, it need to wait a bit then switch bus
properties.
Test on i.MX8QM MEK board, some Micron eMMC will stuck in transfer
mode in this case, and USDHC will never get data transfer complete
status, cause the uboot hang.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
On 16bit variants of the TMIO SD IP, the SECCNT register can only be
programmed to 16bit values, while on the 32bit and 64bit variants it
can be programmed to 32bit values. The SECCNT register indicates the
maximum number of blocks in a continuous transfer. Hence, limit the
maximum continuous transfer block count to 65535 blocks on 16bit
variants of the TMIO IP and to BIT(32)-1 blocks on 32bit and 64bit
variants.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Set MMCIF clock rate to 97.5 MHz, which is the default according
to Gen2 datasheet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The tiny printf implementation only supports %x format specifier,
it does not support %X . Since it makes little difference whether
the debug output prints hex numbers in capitals or not, change it
to %x and make the MMC_TRACE output work with tiny printf too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
According to latest specification rev.0026 and after confirmation with
HW engineer, the DTCNTL register TAPNUM field must be set to 8 even on
H3 ES2.0 SoC. Make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
According to latest specification rev.0026, when HOST_MODE bit 0
(WMODE) is not set, HOST_MODE bit 8 (BUSWIDTH) is ignored. Clear
HOST_MODE bit 8 in such case and align the code with Linux and
avoid possible unforeseen issues.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
