Commit Graph

8800 Commits

Author SHA1 Message Date
Dirk Eibach
acff73fda0 board: gdsys: Enable osd on output only
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2015-11-12 18:04:11 -05:00
Dirk Eibach
da4833c7bf board: gdsys: Add osdsize command
osdsize adjusts the gdsys IHS osd dimensions in characters.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2015-11-12 18:04:11 -05:00
Dirk Eibach
5c3b6dc1fb hrcon: Add fan controllers
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2015-11-12 18:04:10 -05:00
Dirk Eibach
7ed45d3d0a hrcon: Add support for the DH variant
hrcon DH(dual head) has two video outputs per FPGA.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2015-11-12 18:04:10 -05:00
Dirk Eibach
b847f5b622 hrcon: Fix videoboard i2c setup
- i2c addresses for the videoboard port expanders were
  wrong.
- the fpga reset signal was not initialized.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2015-11-12 18:04:09 -05:00
Dirk Eibach
d4e5888801 hrcon: Use generic ioep-fpga support
The strider platform moved some generic code into ioep-fpga.c.
Make use of that on hrcon platform.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2015-11-12 18:04:09 -05:00
Dirk Eibach
a3f9d6c779 mpc83xx: Add strider board
The gdsys strider board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.

On board peripherals include:
- 1x 10/100 Mbit/s Ethernet (optional)
- Lattice ECP3 FPGA connected via eLBC

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
[trini: Drop setting CONFIG_SYS_GENERIC_BOARD, this is always true now]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-12 18:03:48 -05:00
Reinhard Pfau
57b84a0d5a iocon: reset FPGAs in last_stage_init()
- Reset FPGAs in last_stage_init()

Signed-off-by: Reinhard Pfau <pfau@gdsys.de>
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2015-11-12 15:59:05 -05:00
Dirk Eibach
1c7639ae8a controlcenterd: Disable sideband clocks
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2015-11-12 15:59:04 -05:00
Dirk Eibach
e1d1127a9a dlvision-10g: Support displayport
Support dlvision-10g hardware with displayport output.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2015-11-12 15:59:04 -05:00
Dirk Eibach
d054c2f8c6 board: gdsys: Consider DP501 limits on link training
DP501 only supports DP 1.1a.
Limit settings for link bandwidth and lane count to
values allowed by DP 1.1a.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2015-11-12 15:59:03 -05:00
Dirk Eibach
2302fd32a5 board: gdsys: Increase DP501 I2C retry interval
With Club 3D dual link adapter there are AUX-channel timeouts
when EDID is read. Increasing retry interval time to max (400us)
fixes this.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
2015-11-12 15:59:03 -05:00
Dirk Eibach
0caad193cd board: gdsys: Configure DP501 SPDIF input
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
2015-11-12 15:59:02 -05:00
robertcnelson@gmail.com
9606f71002 board/ti/am335x: beaglebone stop muxing i2c1_pin_mux
On the BeagleBone these i2c1 pins are routed to the expanasion header, where
they can be defined as either pr1_usart0_Xxd/pwm0/spi0/i2c1, dont assume i2c1

Fixes: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/313894/1387696

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com>
CC: Tom Rini <trini@konsulko.com>
2015-11-12 13:19:02 -05:00
Hannes Petermaier
91931f7ed3 board/BuR/kwb: use bootvx(...) (with bootline feature) instead go(...)
Since we don't have for sure a valid IP-setup during
board_late_init(...) because it maybe allready stored in environment or
not, we cannot form a proper vxWorks bootline at this place.

So we move to the way, forming the bootline just before
executing/launching vxWorks. To do this we use the bootvx command
instead go.

We only have to form the "othbootargs" environment variable, the rest is
done pretty good by the "bootvx" commannd.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-11-12 13:17:27 -05:00
Thomas Chou
038be18fd9 nios2: add 3c120 and 10m50 devboards MAINTAINERS
Add 3c120 and 10m50 devboards MAINTAINERS

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
2015-11-12 08:26:59 +08:00
Tom Rini
cad0499071 Merge branch 'master' of git://git.denx.de/u-boot-arm 2015-11-10 13:38:08 -05:00
Fabio Estevam
9549867c86 ls1043ardb: Add missing config entries to MAINTAINERS
ls1043ardb_nand_defconfig and ls1043ardb_sdcard_defconfig are missing
in the MAINTAINERS file, so add them for completeness.

Reported-by: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2015-11-10 16:52:58 +01:00
Tom Rini
3a90cb676f board/ti: Update MAINTAINERS entries with more boards
A few config files have been added without updating MAINTAINERS.

Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-10 16:52:46 +01:00
Tom Rini
7ff15aca1a powerpc: Finish updating u-boot*lds scripts for newer binutils
In 522b021 we dropped 'PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4)' lines in
the mpc85xx linker scripts as this is not required and breaks newer
binutils.  This commit cleans up the rest of the powerpc linker scripts.

Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-10 09:20:29 -05:00
Tom Rini
d89059beed board/ti: Update MAINTAINERS entries with more boards
A few config files have been added without updating MAINTAINERS.

Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-10 09:20:27 -05:00
Tom Rini
da58dec866 Various Makefiles: Add SPDX-License-Identifier tags
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one.  This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.

Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-10 09:19:52 -05:00
Albert ARIBAUD
3562936373 Revive OpenRD targets
Revert commit 7a2c1b13 which dropped OpenRD boards.
Assume maintainership of OpenRD.
Remove OpenRD from scrapyard.
Switch OpenRD to generic board.
Switch to Thumb build.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2015-11-10 15:04:21 +01:00
Tom Rini
ed02c532be Merge branch 'master' of git://git.denx.de/u-boot-video 2015-11-05 07:47:21 -05:00
Tom Rini
60b25259a5 Merge git://git.denx.de/u-boot-samsung 2015-11-05 07:46:45 -05:00
Bin Meng
4b6d09449f video: Drop DEV_EXT_VIDEO flag
DEV_EXT_VIDEO does not have any actual meaning, hence drop it.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-11-05 08:24:42 +01:00
Bin Meng
1caf934a05 video: Drop DEV_FLAGS_SYSTEM flag
DEV_FLAGS_SYSTEM does not have any actual meaning, hence drop it.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-11-05 08:22:21 +01:00
Tom Rini
8168ee38c2 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2015-11-04 18:30:51 -05:00
Andy Fleming
87e29878ca mpc85xx: Add support for the Varisys Cyrus board
This board runs a P5020 or P5040 chip, and utilizes
an EEPROM with similar formatting to the Freescale P5020DS.

Large amounts of this code were developed by
Adrian Cox <adrian at humboldt dot co dot uk>

Signed-off-by: Andy Fleming <afleming@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-04 15:19:34 -08:00
Michal Simek
1e370ef7e7 ARM: zynq: Remove zc70x target
Remove zc70x target which was one setting for zc702 and zc706.
Currently zc702 and zc706 are separated.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2015-11-04 14:49:53 +01:00
Daniel Gorsulowski
83bf005710 arm: at91: reworked meesc board support
Signed-off-by: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
2015-11-03 14:21:32 +01:00
Yangbo Lu
bf50be835e mmc: fsl_esdhc: enable EVDD automatic control for SD/MMC Legacy Adapter Card
When detecting SDHC Adapter Card Type 2(SD/MMC Legacy Adapter Card),
enable EVDD automatic control via SDHC_VS. This could support SD card
IO voltage switching for UHS-1 speed mode.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-02 08:50:29 -08:00
Yangbo Lu
cdc69550d2 mmc: fsl_esdhc: enable dat[4:7] for eMMC4.5 Adapter Card
If adapter card type identification is supported for platform, we would
enable dat[4:7] for eMMC4.5 Adapter Card.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-02 08:49:51 -08:00
Zhao Qiang
d468377672 t1040d4rdb: assign muxed pins to qe-tdm when set hwconfig qe-tdm
qe-tdm is muxed with diu, if hwconfig setted as qe-tdm,
assign muxed pins to qe-tdm, then delete diu node from
device tree.

Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-02 08:48:20 -08:00
Minkyu Kang
de5f9733f6 samsung: clean up checkpatch issues
This patch will fix these checkpatch issues.

CHECK: Alignment should match open parenthesis
+			printf("Enter: %s %s\n", mode_name[mode][0],
+						 mode_info[mode]);

CHECK: Alignment should match open parenthesis
+			lcd_printf("\n\n\t%s %s\n", mode_name[mode][0],
+						    mode_info[mode]);

CHECK: Alignment should match open parenthesis
+		lcd_printf("\t%s  %s - %s\n\n", selection[i],
+						mode_name[i][0],

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-11-02 10:38:22 +09:00
Minkyu Kang
1d83970f6f odroid: clean up checkpatch issues
This patch will fix these checkpatch issues.

+static const char *mmc_regulators[] = {

CHECK: Blank lines aren't necessary before a close brace '}'
+
+}

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-11-02 10:38:22 +09:00
Minkyu Kang
9eae844125 smdk2410: clean up checkpatch issues
This patch will fix these checkpatch issues.

ERROR: spaces required around that '==' (ctx:VxV)
+#if FCLK_SPEED==0		/* Fout = 203MHz, Fin = 12MHz for Audio */

ERROR: spaces required around that '==' (ctx:VxV)
+#elif FCLK_SPEED==1		/* Fout = 202.8MHz */

ERROR: spaces required around that '==' (ctx:VxV)
+#if USB_CLOCK==0

ERROR: spaces required around that '==' (ctx:VxV)
+#elif USB_CLOCK==1

CHECK: spaces required around that ':' (ctx:VxV)
+	  "bne 1b":"=r" (loops):"0" (loops));

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-11-02 10:38:22 +09:00
Minkyu Kang
6b949ba824 smdkv310: clean up checkpatch issues
This patch will fix these checkpatch issues.

WARNING: Avoid unnecessary line continuations
+	gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1, \

WARNING: Avoid unnecessary line continuations
+	gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2, \

WARNING: Avoid unnecessary line continuations
+	gd->bd->bi_dram[2].size = get_ram_size((long *)PHYS_SDRAM_3, \

WARNING: Avoid unnecessary line continuations
+	gd->bd->bi_dram[3].size = get_ram_size((long *)PHYS_SDRAM_4, \

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-11-02 10:38:22 +09:00
Przemyslaw Marczak
1611c8cbcf exynos5-dt-types: add board detection for Odroid XU3/XU3L/XU4.
This commit adds additional file with implementation of board
detection code for Odroid-XU3/XU4.

The detection depends on compatible found in fdt:
- "samsung,exynos5" - uses Exynos5 generic code
- "samsung,odroidxu3" - try detect XU3 revision

There are few revisions of Odroid XU3/XU4, each can be detected
by checking the value of channel 9 of built-in ADC:
 Rev   ADC  Board
 0.1     0  XU3 0.1
 0.2   372  XU3 0.2 | XU3L - no DISPLAYPORT
 0.3  1280  XU4 0.1

The detection code depends on the ADC+10% value.

Implementation of functions:
- set_board_type()     - read ADC and set type
- get_board_rev()      - returns board revision: 1..3
- get_board_type()     - returns board type string

Additional functions with return values of bool:
- board_is_generic()   - true if found compatible "samsung,exynos5"
                         but not "samsung,odroidxu3"
- board_is_odroidxu3() - true if found compatible "samsung,odroidxu3"
                         and one of XU3 revision.
- board_is_odroidxu4() - true if found compatible "samsung,odroidxu3"
                         and XU4 revision.

After I2C controller init, the get_board_type() can check
if the XU3 board is a "Lite" variant, by probing chip
0x40 on I2C0 (INA231 - exists only on non-lite).
This is useful for setting fdt file name at misc_init_r().

Enabled configs:
- CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
- CONFIG_ODROID_REV_AIN
- CONFIG_REVISION_TAG
- CONFIG_BOARD_TYPES

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-11-02 10:38:00 +09:00
Przemyslaw Marczak
bc3f39ea0d samsung: board/misc: check returned pointer for get_board_type() calls
The function get_board_type() is called in two places by common code,
but the returned pointer was never check.

This commit adds checking the returned pointer, before use it.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-11-02 10:37:59 +09:00
Tom Rini
588eec2a86 Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2015-10-30 12:56:58 -04:00
tang yuantian
0210a36988 arm: ls1021atwr: optimize the deep sleep latency
It will take more than 1s when wake up from deep sleep. Most of the
time is spent on outputing information. This patch reduced the deep
sleep latency by:
1. avoid outputing system informaton
2. remove flush cache after DDR restore
3. skip reloading second stage uboot binary when SD boot

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-30 09:19:48 -07:00
Aneesh Bansal
6ec9aef2ce SECURE_BOOT: Correct reading of ITS bit
The ITS bit was being read incorrectly beacause of operator
precedence. The same ahs been corrected.

Signed-off-by: Lawish Deshmukh <lawish.deshmukh@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-30 09:19:47 -07:00
tang yuantian
4632ad773e arm: ls1021a: Add sata support on qds and twr board
Freescale ARM-based Layerscape LS102xA contain a SATA controller
which comply with the serial ATA 3.0 specification and the
AHCI 1.3 specification.
This patch adds SATA feature on ls1021aqds and ls1021atwr boards.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:02 -07:00
Gong Qianyu
c7ca8b07fc armv8/ls1043ardb: Add sd boot support
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:02 -07:00
Yangbo Lu
8ef0d5c438 armv8/ls1043ardb: esdhc: Add esdhc support for ls1043ardb
This patch adds esdhc support for ls1043ardb.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:01 -07:00
Shaohui Xie
e82973414d armv8/ls1043a: Add Fman support
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:01 -07:00
Gong Qianyu
3ad4472923 armv8/ls1043ardb: Add nand boot support
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:01 -07:00
Mingkai Hu
f3a8e2b7d4 armv8/ls1043ardb: Add LS1043ARDB board support
LS1043ARDB Specification:
-------------------------
Memory subsystem:
 * 2GByte DDR4 SDRAM (32bit bus)
 * 128 Mbyte NOR flash single-chip memory
 * 512 Mbyte NAND flash
 * 16 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card

Ethernet:
 * XFI 10G port
 * QSGMII with 4x 1G ports
 * Two RGMII ports

PCIe:
 * PCIe2 (Lanes C) to mini-PCIe slot
 * PCIe3 (Lanes D) to PCIe slot

USB 3.0: two super speed USB 3.0 type A ports

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
2015-10-29 10:34:01 -07:00
Mingkai Hu
9f3183d2d6 armv8/fsl_lsch3: Change arch to fsl-layerscape
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.

Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:00 -07:00