arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c: In function
‘get_sys_info’:
arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c:29:6: warning:
unused variable ‘rcw_tmp’ [-Wunused-variable]
u32 rcw_tmp;
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Other than LS1043A, LS1012A also Chassis Gen2 Architecture compliant.
So Avoid LS1043A specific defines in arch/arm
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It is not mandatory for Layerscape SoCs to have SMMU. SoCs like
LS1012A are layerscape SoC without SMMU IP.
So put SMMU configuration code under SMMU_BASE.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
All the output clock parameters of a DPLL needs to be programmed before
locking the DPLL. But it is being configured after locking the DPLL which
could potentially bypass DPLL. So fixing this sequence.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since 1e6ad55c05 ("armv8/cache: Change cache invalidate and flush
function"), this routine can be used for both cache flushing and
cache invalidation. So, it is better to not include "flush" in
this routine name.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
__asm_dcache_all can directly return to the caller of
__asm_{flush,invalidate}_dcache_all.
We do not have to waste x16 register here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The CDCE913 and CDCEL913 devices are modular PLL-based, low cost,
high performance , programmable clock synthesizers. They generate
upto 3 output clocks from a single input frequency. Each output can
be programmed for any clock-frequency.
Adding support for the same.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Adds an fdt.c file in that defines the ft_cpu_setup() function,
which should be called from a board-specific ft_board_setup()).
This ft_cpu_setup() will currently do nothing for non-secure (GP)
devices but contains pertinent updates for booting on secure (HS)
devices.
Update the omap5 Makefile to include the fdt.c in the build.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the CPU string output so that the device
type is now included as part of the CPU string that
is printed as the SPL or u-boot comes up. This update
adds a suffix of the form "-GP" or "-HS" for production
devices, so that general purpose (GP) and high security
(HS) can be distiguished. Applies to all OMAP5 variants.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Updates the SPL build so that when CONFIG_TI_SECURE_DEVICE
is in use (which it should be when building for secure parts),
the TI secure development package is used to create a valid
secure boot image. The u-boot SPL build processes is NOT aware
of the details of creating the boot image - all of that information
is encapsulated in the TI secure development package, which is
available from TI. More info can be found in README.ti-secure
Right now, two image types are generated, MLO and X-LOADER. The types
are important, as certain boot modes implemented by the device's ROM
boot loader require one or the other (they are not equivalent). The
output filenames are u-boot-spl_HS_MLO and u-boot-spl_HS_X-LOADER. The
u-boot-spl_HS_MLO image is also copied to a file named MLO, which is
the name that the device ROM bootloader requires for loading from the
FAT partition of an SD card (same as on non-secure devices).
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Modifies the config.mk to build secure images when building
the SPL for secure devices.
Depending on the boot media, different images are needed
for secure devices. The build generates u-boot*_HS_* files
as appropriate for the different boot modes. The same u-boot
binary file is processed slightly differently to produce a
different boot image, depending on whether the user wants to
boot off SPI, QSPI or other boot media.
Refer to README.ti-secure for more information.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds a centralized config_secure.mk in omap-common for
OMAP-style TI secure devices to use for boot image generation
Depending on the boot media, different images are needed for
secure devices. These commands generates u-boot*_HS_* files that
need to be used to boot secure devices.
Please refer to README.ti-secure for more information.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Defines CONFIG_TI_SECURE_DEVICE which needs to be turned on
when building images for secure devices. This flag is used
to invoke the secure image creation tools for creating a
boot image that can be used on secure devices. This flag
may also be used to conditionally compile code specific
to secure devices.
This terminology will be used by all OMAP architecture devices,
hence introducing to a common location.
With the creation of Kconfig for omap-common, moved the
sourcing of the Kconfig files for the omap3/4/5 and am33xx
devices from arch/arm/KConfig to the omap-common one.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding support for AM43xx secure devices require the addition
of some SOC specific config options like the amount of memory
used by public ROM and the address of the entry point of u-boot
or SPL, as seen by the ROM code, for the image to be built
correctly.
This mandates the addition of am AM43xx CONFIG option and the
ARM Kconfig file has been modified to source this SOC Kconfig
file. Moving the TARGET_AM43XX_EVM config option to the SOC
KConfig and out of the arch/arm/Kconfig.
Updating defconfigs to add the CONFIG_AM43XX=y statement and
removing the #define CONFIG_AM43XX from the header file.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds a new Kconfig file for AM33xx class devices. We
need a common place to define CONFIG parameters
for these SOCs, especially for adding support
for secure devices.
a) Adds a definition for ISW_ENTRY_ADDR. This is the
address to which the ROM branches when the SOC
ROM hands off execution to the boot loader.
CONFIG_SYS_TEXT_BASE and CONFIG_SPL_TEXT_BASE are set
to this value for AM43xx devices.
b) Adds CONFIG_PUB_ROM_DATA_SIZE which is used to
calculate CONFIG_SPL_MAX_SIZE. This value indicates the
amount of memory needed by the ROM to store data during
the boot process.
Currently, these CONFIG options are used only by AM43xx,
but in future other AM33xx class SOCs will also use them.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a psci_system_reset() which calls the SYSTEM_RESET function of
PSCI 0.2 and can be used by boards that support it to implement
reset_cpu().
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Support RAM and MMC boot mode in SPL also with SPL_FIT images.
In MMC boot mode two boot options are available:
1) Boot flow with ATF(EL3) and full U-Boot(EL2):
aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
mkimage -A arm64 -O linux -T kernel -C none -a 0xfffe5000 -e 0xfffe5000
-d bl31.bin atf.ub
cp spl/boot.bin <sdcard fat partition>
cp atf.ub <sdcard fat partition>
cp u-boot.bin <sdcard fat partition>
2) Boot flow with full U-Boot(EL3):
cp spl/boot.bin <sdcard>
cp u-boot*.img <sdcard>
3) emmc boot mode
dd if=/dev/zero of=sd.img bs=1024 count=1024
parted sd.img mktable msdos
parted sd.img mkpart p fat32 0% 100%
kpartx -a sd.img
mkfs.vfat /dev/mapper/loop0p1
mount /dev/mapper/loop0p1 /mnt/
cp spl/boot.bin /mnt
cp u-boot.img /mnt
cp u-boot.bin /mnt
cp atf.ub /mnt
umount /dev/mapper/loop0p1
kpartx -d sd.img
cp sd.img /tftpboot/
and program it via u-boot
tftpb 10000 sd.img
mmcinfo
mmc write 10000 0 $filesize
mmc rescan
mmc part
ls mmc 0
psu_init() function contains low level SoC setup generated for every HW
design by Xilinx design tools. xil_io.h is only supporting file to fix
all dependencies from tools. The same solution was used on Xilinx Zynq.
The patch also change CONFIG_SYS_INIT_SP_ADDR to the end of OCM which
stays at the same location all the time.
Bootrom expects starting address to be at 0xfffc0000 that's why this
address is SPL_TEXT_BASE.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
MMCSD_MODE_FAT has been renamed to MMCSD_MODE_FS by commit 205b4f33.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MMCSD_MODE_FAT has be renmaed to MMCSD_MODE_FS by commit 205b4f33.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
init_early_memctl_regs() is also be called in board_early_init_f().
So remove the duplicated call in spl code.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the issue about the stack will get corrupted when switching between
the early and final mmu tables is fixed by commit 70e21b064, the
workaround to flush dcache is unnecessary and should be removed.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For Qoriq PPC&ARM v7 platforms, the crypto node is being fixup'ed in
order to update the SEC internal version (aka SEC ERA). This patch
adds the same functionality to the ARMv8 SoCs.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The clock parent of the AHB root clock when using mux option 1
is the SYS PLL 270MHz clock. This is specified in Table 5-11
Clock Root Table of the i.MX 7Dual Applications Processor
Reference Manual.
While it could be a documentation error, the 270MHz parent is
also mentioned in the boot ROM configuration in Table 6-28: The
clock is by default at 135MHz due to a POST_PODF value of 1
(=> divider of 2).
Signed-off-by: Stefan Agner <stefan@agner.ch>
The current delays in the DDR initialization routines for am33xx
architectures are sometimes not running long enough leading to DDR
init errors. On am437x, this shows up as an L3 NOC error after the
kernel boots. This is due to the timer not being initialized
properly, but instead still containing the timer init values from
the boot ROM which cause timers to expire in 1/4th the time
required.
timer_init is typically not called until board_init_r, however on
am33xx/am43xx udelay is required in sdram_init which is called
from board_init_f, so a call to timer_init is required earlier.
Note that this issue introduced in v2015.01 by:
b352dde "am33xx: Drop timer_init call from s_init".
Although this could instead fixed by reverting said commit, it
would cause timer_init to be called twice in both SPL and non-SPL
cases. This gives a little more fine grained control and also
matches what is being done on omap-command and fsl-layerscape.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Commit 724219a65f "ARM: always perform per-CPU GIC init" removed some
ifdefs to unify the MULTIENTRY-vs-non-MULTIENTRY paths. However, the
wrong endif was removed. This patch adds back that missing endif, and
adds a new ifdef to match the endif the now-correctly-terminated block
used to match against. Use "git show -U25 724219a65f55" to see enough
context to make the original issue clear.
In practical terms, this makes no difference to runtime behaviour. The
code that was incorrectly compiled into the binary when ifndef MULTIENTRY
is a no-op for other cases, since branch_if_master evaluates to a hard-
coded jump. The only issues were:
- A few extra instructions were added to the binary.
- The comment on the endif at the very end of the function, indicating
which ifdef it matched, were wrong.
An alternative might be to simply fix the comment on that trailing ifdef,
but that only addresses the second point above, not the first.
Fixes: 724219a65f ("ARM: always perform per-CPU GIC init")
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Unfortunately with this change we now are unable to do FS mode boots
from MMC1 as with the way the code works today we will always load and
assume that the hard-coded raw location contains U-Boot. Further, we
cannot fix this by just changing other logic to try FS-then-RAW as it
would also make us have to ignore what order the ROM is telling us to
try.
This reverts commit 22d90d560a.
Signed-off-by: Tom Rini <trini@konsulko.com>
ABB should be initialized for all required domains voltage domain
for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If
we do not do this, kernel configuring just the frequency using the
default boot loader configured voltage can fail on many corner lot
units and has been hard to debug. This specifically is a concern with
DRA7 generation of SoCs since other than VDD_MPU, all other domains
are only permitted to setup the voltages to required OPP only at boot.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Since we setup the voltage and frequency for the MM domain, we *must*
setup the ABB configuration needed for the domain as well. If we do not
do this, kernel configuring just the frequency using the default boot
loader configured voltage can fail on many corner lot units.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
ABB TX_DONE mask will vary depending on ABB module. For example,
3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain,
DRA7 has it on all domains with the exception of CORE, RTC.
Hence, move the txdone mask definition over to structure describing
voltage domain.
Signed-off-by: Nishanth Menon <nm@ti.com>
This information is already available under vcores->volts.efuse.reg.
There is no reason for duplicating the information since AVS Class 0
definitions are common for OMAP5 and DRA7 and defined with
STD_FUSE_OPP_* macros. This allows a central location of defining
the ABB and voltage definitions especially since they are reused.
This also makes it simpler to prevent mistakes involved when changing
the boot OPP for the device.
Signed-off-by: Nishanth Menon <nm@ti.com>
Add support for Technexion's PICO-IMX6UL-EMMC board.
For information about this board, please visit:
http://www.technexion.com/products/pico/pico-som/pico-imx6-emmc
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Due to incorrect placement of the clock gate cell in the ldb_di[x]_clk tree,
the glitchy parent mux of ldb_di[x]_clk can cause a glitch to enter the
ldb_di_ipu_div divider. If the divider gets locked up, no ldb_di[x]_clk is
generated, and the LVDS display will hang when the ipu_di_clk is sourced from
ldb_di_clk.
To fix the problem, both the new and current parent of the ldb_di_clk should
be disabled before the switch. This patch ensures that correct steps are
followed when ldb_di_clk parent is switched in the beginning of boot.
This patch was ported from the 3.10.17 NXP kernel
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/?h=imx_3.10.17_1.0.1_ga&id=eecbe9a52587cf9eec30132fb9b8a6761f3a1e6d
NXP errata number: ERR009219, EB821
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
The current code in ARMv8's lowlevel_init() skips the per-CPU GIC
initialization ifndef CONFIG_ARMV8_MULTIENTRY. However, the per-CPU init
should always occur; it's just the one-time init that should only happen
on the master.
Once this consideration is taken into account, the only difference between
the paths when CONFIG_ARMV8_MULTIENTRY is undefined/defined is the use of
branch_if_slave. Naively, any unified code would need to invoke this
conditionally upon ifdef CONFIG_ARMV8_MULTIENTRY. However, branch_if_slave
already checks CONFIG_ARMV8_MULTIENTRY and does nothing if it isn't
defined, so we don't even need that ifdef at the call site.
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
v7_maint_dcache_all() does not work reliable when build with gcc6,
see: https://bugzilla.redhat.com/show_bug.cgi?id=1318788
While debugging this I learned that v7_maint_dcache_all() is unreliable
when build with gcc5 too when it is marked as noinline.
This commit fixes the reliability issues by replacing the C-code with
the ready to use asm implementation from the kernel.
Given that this code when written as C-code clearly is quite fragile
(also see the existing comments about the C-code being the way it is
to get optimal assembly) and that we have a proven asm alternative,
I believe that this is the best solution.
Note that we actually already had a copy of the kernel's
v7_flush_dcache_all() before this commit in
arch/arm/mach-uniphier/arm32/lowlevel_init.S.
This commit moves that code arch/arm/cpu/armv7/cache_v7_asm.S, renames
it to __v7_flush_dcache_all(), and adds a v7_flush_dcache_all() wrapper
which saves / restores the clobbered registers for use from C-code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There are ARM SoCs (such as the BCM2837) do not contain an ARM GIC. Fix
the ARMv8 CPU startup code to compile in this case.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This option enable adding new platform suport just by adding defconfig
and DTS file which will target generic configuration for SoC.
Make no sense to extend Kconfig just create a pointer between DTS and
configuration file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This moves the sniper board from the lge to lg, in order to match the devicetree
vendor prefix already defined in the kernel.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Some of the code in arch/arm/cpu/armv7/sunxi is actually armv7 specific, while
most of it is just generic code that could as well be used on an AArch64 SoC.
Move all files that are not really tied to armv7 into a new mach-sunxi
directory.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A83T has 3 USB PHYs: 1 for USB OTG, 1 for standard USB 1.1/2.0 host,
1 for USB HSIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
As the need for various magic sram pokes has shown this maybe useful
info to have. e.g. this shows one of my a23 tablets having an id of
1661 rather then the usual 1650 for the a23.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
I noticed that for certain SoC versions boot0 does a magic poke when
build for A33. I'm not aware of this actually being necessary anywhere,
but better safe then sorry.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>