Commit 08ad9b068a (" ar8031: modify the config func of ar8031 to
ar8021_config") selected 'ar8021_config' as the configuration function
for AR8031.
The correct would be to use 'ar8035_config' instead as AR8031/AR8035
have the same programming model and even share the same phy driver
in the linux kernel: drivers/net/phy/at803x.c.
Tested on a mx6qsabresd and wandboard, which now can work without
any PHY setup code in the board files.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
since:
commit: f05ad9ba "Add a way to skip relocation"
tqm5200s board fails to boot. Reason is that
board_init_f has a function parameter bootflag,
which is not setup in
in arch/powerpc/cpu/mpc5xxx/start.S _start
So board_init_f gets a undefined bootflag,
currently the gd pointer address. Unfortunately
this address sets the GD_FLG_SKIP_RELOC bit,
so u-boot code gets not relocated and u-boot
does not boot ...
Init bootflag with 0, and tqm5200 boots fine again.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <yorksun@freescale.com>
Use snprintf to replace sprintf.
Coverity log:
"
Unbounded source buffer (STRING_SIZE)
string_size: Passing string init_val of unknown size to sprintf.
"
Reported-by: Coverity
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Before calling hsearch_r, initialize callback entry to NULL.
Coverity log:
"
Uninitialized scalar variable (UNINIT)
uninit_use_in_call: Using uninitialized value e.
Field e.callback is uninitialized when calling hsearch_r.
"
Reported-by: Coverity
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Whether CONFIG_SYS_HUSH_PARSER is defined or not, should always
check to free 'buff' to avoid memory leak.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
In struct e1000_rx_desc, field 'length' is declared as
uint16_t, so use le16_to_cpu() to do endianness conversion.
Also drop conversion on 'status' which is declared as
uint8_t.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In pci_map_region(), pass 'range_id' to fdt_read_range(),
otherwise the same address will be mapped again in other
calls to pci_map_region()
Signed-off-by: Miao Yan <yammiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
using checkpatch with Perl 5.22.0 generates a warning,
this is fixed in linux through commit:
commit 4e5d56bdf892e18832a6540b63ebf709966bce2a
Author: Eddie Kovsky <ewk@edkovsky.org>
Date: Wed Sep 9 15:37:52 2015 -0700
checkpatch: fix left brace warning
Using checkpatch.pl with Perl 5.22.0 generates the following warning:
Unescaped left brace in regex is deprecated, passed through in regex;
This patch fixes the warnings by escaping occurrences of the left brace
inside the regular expression.
Adapt it for U-Boot.
Signed-off-by: Heiko Schocher <hs@denx.de>
Table 41 of the JEDEC standard for eMMC says that bit 31 of
the command argument is obsolete when issuing the ERASE
command (CMD38) on page 115 of this document:
http://www.jedec.org/sites/default/files/docs/jesd84-B45.pdf
The SD Card Association Physical Layer Simplified Specification also
makes no mention of the use of bit 31.
https://www.sdcard.org/downloads/pls/part1_410.pdf
The Linux kernel distinguishes between secure (bit 31 set) and
non-secure erase, and this patch copies the macro names from
include/linux/mmc/core.h.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Eric Nelson <eric@nelint.com>
Tested-by: Hector Palacios <hector.palacios@digi.com>
drivers/mtd/ubi/io.c:1354:3: error: 'dump_len' undeclared (first use in
this function)
dump_len = max_t(int, 128, len - i);
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Move setup_display from board_early_init_f to board_init.
Add more clock settings.
Add blacklight iomux setting.
Add display_info_t info for the lvds screen.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
This could avoid executing the code that only applies to i.MX platforms.
The bus_i2c_init() is called before relocation and will assgin value
to a static variable. If U-Boot is then still running in a flash
device, it's theoretically not allowed to write data to flash without
an erasing operation. For i.MX platforms, the U-Boot is always running
in DDR.
Actually it causes asynchronous error when the ARM64 system error
report is enabled and the flash write protect is set.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Check for bmode before reading the boot device
to check if a serial downloader is started,
and returns UART if the serial downloader is set,
letting SPL to wait for an image if
CONFIG_SPL_YMODEM_SUPPORT is set.
This allows to load again a SPL based board
with imx_usb_loader together with a tool
such as kermit.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Tested-by: Eric Nelson <eric@nelint.com>
For some board designs, it might be useful to switch the DC-DC
clock source to something else rather the default 24 MHz, e.g.
for EMI reasons.
For this, override the mxs_power_setup_dcdc_clocksource function
in your board support files.
Example:
void mxs_power_setup_dcdc_clocksource(void)
{
mxs_power_switch_dcdc_clocksource(POWER_MISC_FREQSEL_20MHZ);
}
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Use the macro SETUP_IOMUX_PAD(...) rather than imx_iomux_v3_setup_multiple_pads(...) in order to setup
the pin configuration for ECSPI1.
ARRAY_SIZE(pads) provides the wrong size for imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)) in
case of MX6QDL. In the particular case, the content of GPR12 is overwritten and the IPG/AHB/ATB/ATP clocks
are deactivated. Therefore, the connection to the system via JTAG is not possible anymore. Furthermore,
kernel version 3.0.35 hangs during bootprocess in the function etm_init().
Signed-off-by: Michael Schanz <michael.schanz@congatec.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
If fecmxc_initialize_multi() fails, it frees but does not unregister
the mdio bus, causing subsequent uses of the "mii" command to crash.
Fix this by adding mdio_unregister() calls where needed.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
If the host clock frequency is higher than 100 MHz, the MDIO hold
time needs to be increased from its current setting of one cycle in
order to meet the specified minium of 10 ns. Writing an appropriate
value to the HOLDTIME field of the MII_SPEED register achieves this.
Comment copied from Linux kernel.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
This patch writes the default values for TXTL and RXTL to UARTx_UFCR.
Without this patch some older kernel versions crash as UARTx_UFCR was
not always correctly initialized.
Signed-off-by: Maximilian Schwerin <maximilian.schwerin@tigris.de>
The low four bits of the SYSCTL register are reserved on the USDHC
controller on i.MX6 and i.MX7 processors, but are used for clocking
operations on earlier models.
Guard against their usage by hiding the bit mask macros on those
processors.
These bits are used to prevent glitches when changing clocks on
i.MX35 et al. Use the RSTA bit instead for i.MX6 and i.MX7.
>From the i.MX6DQ RM:
To prevent possible glitch on the card clock, clear the
FRC_SDCLK_ON bit when changing clock divisor value(SDCLKFS
or DVS in System Control Register) or setting RSTA bit.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Hector Palacios <hector.palacios@digi.com>
The ifdef'ed Linux kernel code uses the 1 based port number, whereas U-Boot
puts a 0 based port number into the register. The reason the 0 based port
number apparently works can probably be taken from the USB 2.0 spec:
8.4.2.2 Start-Split Transaction Token
... The host must correctly set the port field for single and multiple TT
hub implementations. A single TT hub implementation *may ignore* the port
field.
Actually, as far as I understand, a multi TT hub defaults to single TT
(bAlternateSetting: 0) until switched via SetInterface, so even "port 42"
would work.
The change was verified by hardcoding the port number to a wrong value,
SPLIT transactions kept working (although using a DWC2 instead of MUSB).
Tested hubs are the RPi onboard SMC9514 and an external "05e3:0608
Genesys Logic, Inc. USB-2.0 4-Port HUB". The former is a multi TT hub,
the latter single TT only.
Addendum: Tested on sunxi/MUSB by Hans de Goede
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Start split and complete split tokens need the hub address and the
downstream port of the first HS hub (device view).
The core of the function was duplicated in both host/ehci_hcd and
musb-new/usb-compat.h.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
flush_dcache_range may access data after priv->aligned_buffer end if
len > DWC2_DATA_BUF_SIZE.
memcpy may access data after buffer end if done > 0
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
The configuration descriptor includes all interface, endpoint and
auxiliary descriptors (e.g. report, union) so 512 bytes may not be enough.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Skip erase if the sector is blank. The sector erase is slow, and
may take 0.7 sec typically or up to 3 sec worst-case.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
If the erase fails, fail_addr might indicate exactly which block
failed. If fail_addr = MTD_FAIL_ADDR_UNKNOWN, the failure was not
at the device level or was not specific to any particular block.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Erase is an asynchronous operation. Device drivers are supposed
to call instr->callback() whenever the operation completes, even
if it completes with a failure.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
There are some reports of stability issues at 672 MHz, see:
http://linux-sunxi.org/Orange_Pi_PC#DRAM_clock_speed_limit
So reduce the DRAM speed to 624MHz which seems to be reliable everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add common configuration bits for the Denali NAND controller and also
support for using it as a boot device in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
It is not possible to compile DFU MMC support if the MMC support is not
compiled into U-Boot. Secure the code with an ifdef to prevent compiler
splat.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
It is not possible to compile MMC/SPI SPL if the respective DM_MMC/DM_SPI
bits are not enabled. Secure the code with an ifdef to prevent compiler
splat.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Make sure the NAND reset is not asserted in full U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
If the system boots from NAND, make sure to de-assert the NAND IP
reset, otherwise the system will get stuck.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Define the NAND reset bit and fix the ordering of the macros.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Update the qspiboot console command to use UBIFS instead
of old jffs2 file system.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Update the qspiboot console command to use UBIFS instead
of old jffs2 file system.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Update the qspiboot console command to use UBIFS instead
of old jffs2 file system.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>