- For am335x_pdu001 we do not want the CPSW driver, drop it
- Re-sync the defconfig for am43xx_evm_rtconly as it came in after the
patch that converted CPSW to Kconfig was posted but before it was
applied.
- Drop empty section / comments from pengwyn
- Drop empty section / comments from baltos and drop unused
CONFIG_SPL_NET_VCI_STRING (it does not enable CONFIG_SPL_NET_SUPPORT
currently and SPL_NET_VCI_STRING has been migrated already).
Cc: Felix Brack <fb@ltec.ch>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Fixes: f02b8d1761 ("Migrate CONFIG_DRIVER_TI_CPSW to Kconfig")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Felix Brack <fb@ltec.ch>
Tested-by: Felix Brack <fb@ltec.ch>
Enable the HS200 on RCar Gen3 platforms, since the SDHI core supports it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since the Renesas SDHI has it's own custom driver sharing the
common code with Uniphier one, adjust the Kconfig entries.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable the HUSH shell, since it is far more capable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add JTAG recovery support into the M2 Porter TPL. This allows the
TPL to be loaded over JTAG, initialize the system, wait for the
JTAG debugger to load U-Boot image into RAM and then resume and
start U-Boot from RAM.
The procedure is as follows:
1) Load u-boot-tpl.bin to 0xe6300000
2) Write magic number 0x1337c0de to 0xe6300020
TPL checks for this particular magic and starts JTAG recovery
if this number is present. This is not present by default.
3) Start U-Boot TPL from 0xe6300000
4) Wait for a message from TPL on UART indicating JTAG boot:
"JTAG boot detected!"
5) Halt the system in JTAG debugger
6) Load U-Boot image (u-boot.img) to 0x4fffffc0
7) Write magic number 0xb33fc0de to 0xe6300024
TPL checks for this particular magic to verify that the U-Boot
image was loaded into DRAM by the JTAG debugger.
8) Resume the system in JTAG debugger
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add and enable TPL on M2 Porter. The TPL must fit into 16 kiB due
to the Gen2 BootROM restriction. The TPL is running from MERAM and
is capable of performing the initial initialization of PFC, Clock,
GPIO, LBSC, DBSC and QSPI NOR. DBSC is responsible for bringing up
the DDR DRAM access. The TPL is capable of loading the next stage,
U-Boot, from either SPI NOR or UART as a fallback. If either does
provide a valid U-Boot uImage, the system stops, which allows the
operator to load U-Boot ie. via JTAG and start it manually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Add support for zc12xx boards. All of them are internal boards for
silicon validation and share very similar base platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enables the fixed link support for
all ZynqMP boards.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot is now able to boot to ARM Trusted Firmware (ATF). The boot
flow is SPL(EL3) loads ATF and full u-boot and jump to ATF(EL3) which
pass control to full u-boot(EL2). This has been tested on zcu106, so
enable it in this defconfig.
To generate an image that triggers this booting flow, you need to pass
'-O arm-trusted-firmware' to mkimage.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_VERSION_VARIABLE had already been mostly migrated to Kconfig,
but two headers still referenced it. Also set defaults so that
most of the defconfigs inherit the default rather than needing it
to be set explicitly.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate the CONFIG_SYS_ALT_MEMTEST option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration after also including CMD_MEMTEST]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move am43xx_evm_qspiboot_defconfig to DM. This is required as SPI core
and TI QSPI driver no longer supports non DM interfaces.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add command GPT support
Add EMMC boot support
Add the 2 other SDMMC instances for ED1:
- SDMMC2 = mmc 1, eMMC on the ED1 board
- SDMMC3 = extension connector, deactivated by default
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Kernel stores information to the RTC_SCRATCH0 and RTC_SCRATCH1 registers
for wakeup from RTC-only mode with DDR in self-refresh. Parse these
registers during SPL boot and jump to the kernel resume vector if the
device is waking up from RTC-only modewith DDR in Self-refresh.
The RTC scratch register layout used is:
SCRATCH0 : bits00-31 : kernel resume address
SCRATCH1 : bits00-15 : RTC magic value used to detect valid config
SCRATCH1 : bits16-31 : board type information populated by bootloader
During the normal boot path the SCRATCH1 : bits16-31 are updated with
the eeprom read board type data. In the rtc_only boot path the rtc
scratchpad register is read and the board type is determined and
correspondingly ddr dpll parameters are set. This is done so as to avoid
costly i2c read to eeprom.
RTC-only +DRR in self-refresh mode support is currently only enabled for
am43xx_evm_rtconly_config.
This is not to be used with epos evm builds.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[j-keerthy@ti.com Rebased to latest u-boot master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable NETCONSOLE by default. Still requires changes to the boot
environment to enable on the platform.
Signed-of-by: Jason Kridner <jdk@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some config is redundant with Kconfig. Fix it.
Also remove unused configs
Move SDRAM_MAX_SIZE in the only place it is used
include/environment.h already defines CONFIG_ENV_SIZE
from CONFIG_ENV_SECT_SIZE and defines CONFIG_ENV_ADDR as
(CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
remove BOOTARGS as bootargs is set by the different boot commands
Fix CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE to be in
line with CPM DPRAM organisation
Remove CONFIG_SYS_GBL_DATA_SIZE, CONFIG_SYS_GBL_DATA_OFFSET and
CONFIG_SYS_INIT_SP_OFFSET which are unused
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
CONFIG_8xx doesn't mean much outside of arch/powerpc/
This patch renames it CONFIG_MPC8xx just like CONFIG_MPC85xx etc ...
It also renames 8xx_immap.h to immap_8xx.h to be consistent with
other file names.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
ATMEL_SPI is now fully converted to driver-model and
respective boards switch to DM_SPI as well,
so make default y for ARCH_AT91
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
Sync DTS from Linux and add FDT support for AT91 ma5d4evk board.
usb0, usb1, usb2 and hlcdc_pwm nodes removed, since there is no support it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync DTS from Linux and add FDT support for AT91 vinco board.
usb0, usb1, and usb2 nodes removed, since there is no support it.
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Now CONFIG_ATMEL_SPI is defined in Kconfig, so move the
same into defconfig file.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
Highlights this time around:
- Support for new RPi3 B+ model
- Fix for some SD cards on newer RPi firmware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=jqq6
-----END PGP SIGNATURE-----
Merge tag 'signed-rpi-next' of git://github.com/agraf/u-boot
Patch queue for rpi - 2018-04-06
Highlights this time around:
- Support for new RPi3 B+ model
- Fix for some SD cards on newer RPi firmware
The new Raspberry Pi B 3+ has a lan78xx device attached to it. Let's add
driver support in U-Boot for it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The new Raspberry Pi B 3+ has a lan78xx device attached to it. Let's add
driver support in U-Boot for it.
Signed-off-by: Alexander Graf <agraf@suse.de>
When we enable CONFIG_OF_BOARD on Raspberry Pis, we may end up without
serial console support in early boot. Hence we need to make the serial
port optional, otherwise we will never get to the point where serial
would be probed.
Signed-off-by: Alexander Graf <agraf@suse.de>
