This patch add support PCI of SuperH base code and SH7780 specific code.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SH7780 is CPU of Renesas Technology.
This CPU has
- CPU clock 400MHz
- PCI support
- DDR-SDRAM controller
- etc ...
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Migo-R is a board based on SH7722 and has may devices.
In this patch, supported SCIF, NOR flash and Ethernet.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since all ECC related problems seem to be resolved on LWMON5, this patch
now enables ECC support.
We have to write the ECC bytes by zeroing and flushing in smaller
steps, since the whole 256MByte takes too long for the external
watchdog.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch contains updates for changes for the Korat PPC440EPx board.
These changes include:
(1) Support for "permanent" and "upgradable" copies of U-Boot, as
described in the new "doc/README.korat" file;
(2) a new memory map for the registers in the board's CPLD;
(3) a revised format for manufacturer's data in serial EEPROM; and
(4) changes to track updates to U-Boot for the Sequoia board.
Signed-off-by: Larry Johnson <lrj@acm.org>
Since this board will probably be ported to arch/powerpc in the
near future, we add device tree support now. This way we are
"ready" for arch/powerpc from now on.
Signed-off-by: Stefan Roese <sr@denx.de>
If CFG_MEM_TOP_HIDE is defined in the board config header, this specified
memory area will get subtracted from the top (end) of ram and won't get
"touched" at all by U-Boot. By fixing up gd->ram_size the Linux kernel
should gets passed the now "corrected" memory size and won't touch it
either. This should work for arch/ppc and arch/powerpc. Only Linux board
ports in arch/powerpc with bootwrapper support, which recalculate the
memory size from the SDRAM controller setup, will have to get fixed
in Linux additionally.
This patch enables this config option on some PPC440EPx boards as a workaround
for the CHIP 11 errata. Here the description from the AMCC documentation:
CHIP_11: End of memory range area restricted access.
Category: 3
Overview:
The 440EPx DDR controller does not acknowledge any
transaction which is determined to be crossing over the
end-of-memory-range boundary, even if the starting address is
within valid memory space. Any such transaction from any PLB4
master will result in a PLB time-out on PLB4 bus.
Impact:
In case of such misaligned bursts, PLB4 masters will not
retrieve any data at all, just the available data up to the
end of memory, especially the 440 CPU. For example, if a CPU
instruction required an operand located in memory within the
last 7 words of memory, the DCU master would burst read 8
words to update the data cache and cross over the
end-of-memory-range boundary. Such a DCU read would not be
answered by the DDR controller, resulting in a PLB4 time-out
and ultimately in a Machine Check interrupt. The data would
be inaccessible to the CPU.
Workaround:
Forbid any application to access the last 256 bytes of DDR
memory. For example, make your operating system believe that
the last 256 bytes of DDR memory are absent. AMCC has a patch
that does this, available for Linux.
This patch sets CFG_MEM_TOP_HIDE for the following 440EPx boards:
lwmon5, korat, sequoia
The other remaining 440EPx board were intentionally not included
since it is not clear to me, if they use the end of ram for some
other purpose. This is unclear, since these boards have CONFIG_PRAM
defined and even comments like this:
PMC440.h:
/* esd expects pram at end of physical memory.
* So no logbuffer at the moment.
*/
It is strongly recommended to not use the last 256 bytes on those
boards too. Patches from the board maintainers are welcome.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the AMCC Glacier 460GT eval board.
The main difference to the Canyonlands board are listed here:
- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Currently EMAC2+3 are not working. This will be fixed in a later
release.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes compilation error
cmd_usb.c: In function 'do_usb':
cmd_usb.c:552: error: void value not ignored as it ought to be
Signed-off-by: Anatolij Gustschin <agust@denx.de>
original ata_piix driver is using IDE framework, not real
SATA framework. For now, the ata_piix driver is only used
by x86 sc520_cdp board. This patch makes the ata_piix driver
use the new SATA framework, so
- remove the duplicated command stuff
- remove the CONFIG_CMD_IDE define in the sc520_cdp.h
- add the CONFIG_CMD_SATA define to sc520_cdp.h
Signed-off-by: Dave Liu <daveliu@freescale.com>
move the cmd_sata.c from common/ to drivers/ata_piix.c,
the cmd_sata.c have some part of ata_piix controller drivers.
consolidate the driver to have better framework.
Signed-off-by: Dave Liu <daveliu@freescale.com>
The following changes are needed to be inline with ePAPR v0.81:
* r4, r5 and now always set to 0 on boot release
* r7 is used to pass the size of the initial map area (IMA)
* EPAPR_MAGIC value changed for book-e processors
* changes in the spin table layout
* spin table supports a 64-bit physical release address
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Each file that can be built here now follows some
CONFIG_ option so that they are appropriately built
or not, as needed. And CONFIG_ defines were added
to various board config files to make sure that happens.
The other board/freescale/*/Makefiles no longer need
to reach up and over into ../common to build their
individually needed files any more.
Boards that are CDS specific were renamed with cds_ prefix.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
get_ddr_freq() and get_bus_freq() used get_sys_info() each time they were
called. However, get_sys_info() recalculates extraneous information when
called each time. Have get_ddr_freq() and get_bus_freq() return memoized
values from global_data instead.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL has taken to using SVR[16:23] as an SOC sub-version field. This
is used to distinguish certain variants within an SOC family. To
account for this, we add the SVR_SOC_VER() macro, and update the SVR_*
constants to reflect the larger value. We also add SVR numbers for all
of the current variants. Finally, to make things neater, rather than
use an enormous switch statement to print out the CPU type, we create
and array of SVR/name pairs (using a macro), and print out the CPU name
that matches the SVR SOC version.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Added the cpu command that provides a generic mechanism to get status,
reset, and release secondary cores in multicore processors.
Added support for using the ePAPR defined spin-table mechanism on 85xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we go to 36-bit physical addresses we need to keep the concept of
the physical CCSRBAR address seperate from the virtual one.
For the majority of boards CFG_CCSBAR_PHYS == CFG_CCSRBAR
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Linux understands "host" (default), "peripheral" and "otg" (broken).
Though, U-Boot doesn't restrict dr_mode variable to these values (think
of renames in future).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
With the original value of 1/2 clock cycle delay, the system ran relatively
stable except when we run benchmarks that are intensive users of memory.
When I run samba connected disk with a HDBENCH test, the system locks-up
or reboots sporadically.
Signed-off by: Joe D'Abbraccio <Joe.D'abbraccio@freescale.com>
The device trees for these boards describe PCI I/O as starting from
address zero from the device's perspective.
Placing I/O elsewhere may cause problems with certain PCI boards, and may
cause problems with Linux.
Signed-off-by: Scott Wood <scottwood@freescale.com>
At least on the "33MHz Pilot" board crystal is actually 33.3MHz.
This patch fixes "system time drifting" problem.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Plus modify environment to use it and remove bootfile env variable,
it is internal and CONFIG_BOOTFILE is used for these purposes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Current DDR setup easily causes memory corruption, this patch fixes it.
Also fix TIMING_CFG0_MRS_CYC definition.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
On the MPC8377ERDB: 2 SATA and 2 PCI-E.
On the MPC8378ERDB: 2 PCI-E
On the MPC8379ERDB: 4 SATA
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
There's no on-board RTC on the MPC8323ERDB, but there is an EEPROM.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
The following changes are based on kernel UCC ethernet performance:
1. Make the CSB bus pipeline depth as 4, and enable the repeat mode
2. Optimize transactions between QE and CSB. Added CFG_SPCR_OPT
switch to enable this setting.
The following changes are based on the App Note AN3369 and
verified to improve memory latency using LMbench:
3. CS0_CONFIG[AP_n_EN] is changed from 1 to 0
4. CS0_CONFIG[ODT_WR_CONFIG] set to 1. Was a reserved setting
previously.
5. TIMING_CFG_1[WRREC] is changed from 3clks to 2clks (based on
Twr=15ns, and this was already the setting in DDR_MODE)
6. TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on
Trp=15ns)
7. TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on
Tras=40ns)
8. TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on
Trcd=15ns)
9. TIMING_CFG_1[REFREC] changed from 21 clks to 11clks. (based on
Trfc=75ns)
10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks. (based
on Tfaw=50ns)
11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based
on CL=3 and WL=2).
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Use available shift/mask macros to define DDR configuration.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Update the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB board files to upload
the Vitesse VSC7385 firmware. Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET.
Cleaned up the board header files to make selecting the VSC7385 easier to
control.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The Vitesse VSC7385 is a 5-port switch found on the Freescale MPC8349E-mITX
and other boards. A small firwmare must be uploaded to its on-board memory
before it can be enabled. This patch adds the code which uploads firmware
(but not the firmware itself).
Previously, this feature was provided by a U-Boot application that was
made available only on Freescale BSPs. The VSC7385 firmware must still
be obtained separately, but at least there is no longer a need for a separate
application.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
These defines embedded the u-boot env variables and/or the bd_t structure
in the fdt blob. The conclusion of discussion on the u-boot email list
was that embedding these in the fdt blob is not useful: there are better
ways of passing the data (in fact, the fdt blob itself replaces the
bd_t struct).
The only board that enables these is the stxxtc and they don't appear
to be used by linux.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Add a simple expr style command that will set an env variable as the result
of the command. This allows us to do simple math in shell. The following
operations are supported: &, |, ^, +, -, *, /.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch replaces the current function definitions with NESTED, LEAF
and END macro. They specify some more additional information about the
function; an alignment of symbol, type of symbol, stack frame usage, etc.
These information explicitly tells the assembler and the debugger about
the types of code we want to generate.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Disable default building of new uImage format support in preparation
for merge with the master. Support for new format can be enabled on
a per-board basis, by defining the following in the board's config file:
#define CONFIG_FIT 1
#define CONFIG_OF_LIBFDT 1
This can be optionally defined to give more verbose output:
#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Modify the RTC API to provide one a status for the time reported by
the rtc_get() function:
0 - a reliable time is guaranteed,
< 0 - a reliable time isn't guaranteed (power fault, clock issues,
and so on).
The RTC chip drivers are responsible for providing this info if the
corresponding chip supports such functionality. If not - always
report that the time is reliable.
The POST RTC test was modified to detect the RTC faults utilizing
this new rtc_get() feature.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
- insert partition for dtb blob to TQM5200B MTD layout
- set env variables dependent on the configured board
(TQM5200 or TQM5200B)
Signed-off-by: Martin Krause <martin.krause@tqs.de>
This patch adds an fdt_next_node() function which can be used to
iterate through nodes of the tree while keeping track of depth. This
function is used to simplify the iteration code in a lot of other
functions, and is also exported for use by library users.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This patch adds an fdt_set_name() function to libfdt, mirroring
fdt_get_name(). This is a r/w function which alters the name of a
given device tree node.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To enable this, alternative, configuration the U-Boot board configuration
file for lwmon5 includes the definitions of alternative addresses for header
(CONFIG_ALT_LH_ADDR) and buffer (CONFIG_ALT_LB_ADDR).
The Linux shall be configured with the CONFIG_ALT_LB_LOCATION option set,
and has the BOARD_ALT_LH_ADDR and BOARD_ALT_LB_ADDR constants defined in the
lwmon5 board-specific header (arch/ppc/platforms/4xx/lwmon5.h).
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
The parallel flash on the BF537-STAMP is CFI compliant, so there is no need
for the board specific driver at all. Just use the common CFI driver.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Stop tying things to the processor that should be tied to other defines and
change BFIN_CPU to CONFIG_BFIN_CPU so that it can be used in the build
system to select the -mcpu option.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
460EX doesn't support a fixed bootstrap option to boot from 512 byte page
NAND devices. The only bootstrap option for NAND booting is option F for
2k page devices. So to boot from a 512 bype page device, the I2C bootstrap
EEPROM needs to be programmed accordingly.
This patch adds basic NAND booting support for the AMCC Canyonlands aval
board and also adds support to the "bootstrap" command, to enable NAND
booting I2C setting.
Tested with 512 byte page NAND device (32MByte) on Canyonlands.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes the physical addess parameter from 32bit to 64bit.
This is needed for 36bit 4xx platforms to access areas located
beyond the 4GB border, like SoC peripherals (EBC etc.).
Signed-off-by: Stefan Roese <sr@denx.de>
Cleanup: Remove custom flash driver for 8 bit boot-eprom and replace it with
the FLASH_CFI_LEGACY et al. config options.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
MD5 supoprt is turned on by defining CONFIG_MD5, the digest can be then
calculated using the md5() function -- see include/md5.h for details.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
verify, autostart and lmb fields are used regardless of CONFIG_FIT
setting, move their definitions to common section.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Save FIT configuration provied in the first bootm argument and use it
when to get ramdisk/FDT subimages when second and third (ramdisk/FDT)
arguments are not specified.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
autoscript() routine is updated to accept second argument, which
is only used for FIT images and provides a FIT subimage unit name.
autoscript() routine callers must now pass two arguments. For
non-interactive use (like in cmd_load.c, cmd_net.c), new environment
variable 'autoscript_uname' is introduced and used as a FIT
subimage unit name source.
autoscript command accepts extended syntax of the addr argument:
addr:<subimg_uname>
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
This patch adds new node offset fields to struct bootm_headers
and updates bootm_headers processing code to make use of them.
Saved node offsets allow to avoid repeating fit_image_get_node() calls.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
boot_get_ramdisk() and image_get_ramdisk() do not need all
cmdtp, flag, argc and argv arguments. Simplify routines definition.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Support for the new uImage format (FIT) is added to mkimage tool.
Commandline syntax is appropriately extended:
mkimage [-D dtc_options] -f fit-image.its fit-image
mkimage (together with dtc) takes fit-image.its and referenced therein
binaries (like vmlinux.bin.gz) as inputs, and produces fit-image file -- the
final image that can be transferred to the target (e.g., via tftp) and then
booted using the bootm command in U-Boot.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Add FDT-based functions for handling new format component images,
configurations, node operations, property get/set, etc.
fit_ - routines handling global new format uImage operations
like get/set top level property, process all nodes, etc.
fit_image_ - routines handling component images subnodes
fit_conf_ - routines handling configurations node
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
the dts file basenames were updated in linux - this helps avoid
inadvertently loading any old dtbs laying around.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
1. Make the CSB bus pipeline depth as 4, and enable
the repeat mode;
2. Raise the eTSEC emergency priority;
3. Use the highest IP blocks clock.
Signed-off-by: Dave Liu <daveliu@freescale.com>
The latter version stops when "run load" fails for whatever reasons
rendering the combination *a lot* more secure.
Signed-off-by: Detlev Zundel <dzu@denx.de>
This fixes the cluster size tests in the FAT32 file system.
The current implementation of VFAT support doesn't work if the
referred cluster has an offset > 16bit representation, causing
"fatload" and "fatls" commands etc. to fail.
Signed-off-by: michael trimarchi <trimarchi@gandalf.sssup.it>
The 405EZ only supports 512 bytes of rx-/tx-fifo EMAC sizes. But
currently 4k/2k is configured. This patch fixes this issue.
Thanks to Thomas Kindler <tkindler@lenord.de> for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
Adds PCI support for MPC5121
Tested with drivers/net/rtl8139.c
Support is conditional since PCI on old silicon does not work.
ads5121_PCI_config turns on PCI
In this version, condition compilation of PCI code has been moved
from ifdef in board/ads5121/pci.c to board/ads5121/Makefile as
suggested by Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: John Rigby <jrigby@freescale.com>
The previous patch was lacking of i386, microblaze, nios and nios2. This
patch tries to fix them.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
This patch adds an fdt_next_node() function which can be used to
iterate through nodes of the tree while keeping track of depth. This
function is used to simplify the iteration code in a lot of other
functions, and is also exported for use by library users.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This patch adds the following common routines:
1) Dedicated mkimage print_header() is replaced with common
image_print_contents()
image_print_contents_noindent()
2) Common os/arch/type/comp fields name <--> id translation routines
genimg_get_os_name()
genimg_get_arch_name()
genimg_get_type_name()
genimg_get_comp_name()
genimg_get_os_id()
genimg_get_arch_id()
genimg_get_type_id()
genimg_get_comp_id()
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
This patch introduces the following prefix convention for the
image format handling and bootm related code:
genimg_ - dual format shared code
image_ - legacy uImage format specific code
fit_ - new uImage format specific code
boot_ - booting process related code
Related routines are renamed and a few pieces of code are moved around and
re-grouped.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Allow the user to set 'bootm_low' and 'bootm_size' env vars as a way
to restrict what memory range is used for bootm.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Marian Balakowicz <m8@semihalf.com>
Convert generic ramdisk_high(), get_boot_cmdline(), get_boot_kbd()
functions over to using lmb for allocation of the ramdisk, command line
and kernel bd info.
Convert PPC specific fdt_relocate() to use lmb for allocation of the device
tree.
Provided a weak function that board code can call to do additional
lmb reserves if needed.
Also introduce the concept of bootmap_base to specify the offset in
physical memory that the bootmap is located at. This is used for
allocations of the cmdline, kernel bd, and device tree as they should
be contained within bootmap_base and bootmap_base + CFG_BOOTMAPSZ.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The autostart env variable was dropped as part of the initial new uImage
cleanup. Add it back here so the arch specific code can decide if it
wants to really boot or not.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Marian Balakowicz <m8@semihalf.com>
Introduce the LMB lib used on PPC in the kernel as a clean way to manage
the memory spaces used by various boot images and structures. This code
will allow us to simplify the code in bootm and its support functions.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Changed image_get_ramdisk() to just return NULL on error and have
get_ramdisk() propogate that error to the caller. It's left to the
caller to call do_reset() if it wants to.
Also moved calling do_reset() in get_fdt() and fdt_relocate() on ppc
to a common location. In the future we will change get_fdt() and
fdt_relocate() to return success/failure and not call do_reset() at all.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Marian Balakowicz <m8@semihalf.com>
We don't actually need the kdb param as we are just using it to get
bd->bi_memsize which we can get from gd->bd->bi_memsize. Also, if we
boot via OF we might not actually fill out a kdb.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Marian Balakowicz <m8@semihalf.com>
Dual format image code must properly handle all three FDT passing methods:
- raw FDT blob passed
- FDT blob embedded in the legacy uImage
- FDT blob embedded in the new uImage
This patch enables proper raw FDT handling when no FIT imaeg support
is compiled in. This is a bit tricky as we must dected FIT format even
when FIT uImage handling is not enabled as both FIT uImages and raw FDT
blobs use tha same low level format (libfdt).
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Do not pass image verification flag directly to related routines.
Simplify argument passing and move it to the bootm_header structure which
contains curently processed image specific data and is already being passed
on the argument list.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds framework for dual format images. Format detection is added
and the bootm controll flow is updated to include cases for new FIT format
uImages.
When the legacy (image_header based) format is detected appropriate
legacy specific handling is invoked. For the new (FIT based) format uImages
dual boot framework has a minial support, that will only print out a
corresponding debug messages. Implementation of the FIT specific handling will
be added in following patches.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
----------------------------------------------------------------
Olaf Hering [Wed, 17 Oct 2007 06:27:13 +0000 (23:27 -0700)]
Remove the __STRICT_ANSI__ check from the __u64/__s64 declaration on
32bit targets.
GCC can be made to warn about usage of long long types with ISO C90
(-ansi), but only with -pedantic. You can write this in a way that even
then it doesn't cause warnings, namely by:
#ifdef __GNUC__
__extension__ typedef __signed__ long long __s64;
__extension__ typedef unsigned long long __u64;
#endif
The __extension__ keyword in front of this switches off any pedantic
warnings for this expression.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
----------------------------------------------------------------
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
The Linux commit fac8b209b1084bc85748bd54e13d00c1262b220f ("Remove
final traces of long-deprecated "ramdisk" kernel parm") makes these
changes neccessary.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Some boards (e.g. lwmon5) may use rather small watchdog intervals, so
causing it to reboot the board if U-Boot does a long busy-wait with
udelay(). Thus, for these boards we have to restart WD more
frequently.
This patch splits the busy-wait udelay() into smaller, predefined,
intervals, so that the watchdog timer may be resetted with the
configurable (CONFIG_WD_PERIOD) interval.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Adds configuration option for ATI Radeon 9200 card
support to sequoia config file. If CONFIG_VIDEO
is enabled, TEXT_BASE should be changed to 0xFFF80000.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Introducing routines for parsing new uImage format bootm arguments:
[<addr>]#<conf> - configuration specification
[<addr>]:<subimg> - subimage specification
New format images can contain multiple subimages of the same type. For example
a single new format image file can contain three kernels, two ramdisks and a
couple of FDT blobs. Subimage and configuration specifications are extensions
to bootm (and other image-related commands) arguments' syntax that allow to
specify which particular subimage should be operated on.
Subimage specification is used to denote a particular subimage. Configurations
are a bit more complex -- they are used to define a particualr booting setup,
for example a (kernel, fdt blob) pair, or a (kernel, ramdisk, fdt blob) tuple,
etc.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
This routine assures that image (whether legacy or FIT) is not
in a special dataflash storage.
If image address is a dataflash address image is moved to system RAM.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
New uImage format (Flattened Image Tree) requires libfdt
functionality, print out error message if CONFIG_OF_LIBFDT
is not defined.
New uImage support is enabled by defining CONFIG_FIT (and CONFIG_OF_LIBFDT).
This commit turns it on by default.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Back in commit 975a083a5e where
I tried to "8610HPCD: Fix typos in two PCI setup registers", I
botched it due to not realizing that 8610 and 8641 had different
Global Utility Register defintions, one of which was like 85xx,
and the other wasn't. Correct this problem by introducing two
symbols, one for each 86xx SoC, but neither of which is named
anything like 85xx.
My bad. Lovely Wednesday with git bisect. You know.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Without an actual supported video card hooked up, enabling
the CONFIG_VIDEO by default just makes it look broken by
routing all console output to the video card. Don't.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
The two symbols MPC86xx_PORDEVSR_IO_SEL and MPC86xx_PORBMSR_HA
were erroneously present as 85xx names and values, leftover from
the clone wars. Fix this by removing the 85xx cruft from the
86xx codebase.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This is the proper fix for a missing closing brace in the function
ft_cpu_setup() noticed by joe.hamman <at> embeddedspecialties.com.
The ft_cpu_setup() function in mpc8641hpcn.c should have been
removed earlier as it was under the obsolete CONFIG_OF_FLAT_TREE,
but was missed. Only, the sbc8641d was nominally still using it.
It all got ripped out, and the funcality that was in ft_board_setup()
was refactored to remove the CPU portions into the new file
cpu/mpc86xx/fdt.c instead. Make sbc8641d use this now.
Based loosely on an original patch from joe.hamman@embeddedspecialties.com
Signed-off-by: Jon Loeliger <jdl@freescale.com>