Commit Graph

1393 Commits

Author SHA1 Message Date
Andreas Dannenberg
70942db4dd mmc: am654_sdhci: Allow driver to probe without PDs specified
We would like to use the driver even without power domains being
specified for cases such as during early boot when the required power
domains have already gotten enabled by the SoC's boot ROM and such
explicit initialization is not needed and possible.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17 11:12:54 -04:00
Faiz Abbas
f605807f3d mmc: am654_sdhci: Add a platform specific set_control_reg() callback
Add a platform specific set_control_reg() callback to help switch to
UHS speed modes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17 11:12:08 -04:00
Faiz Abbas
d1c0a2200a mmc: sdhci: Add support for HOST_CONTROL2 and setting UHS timings
The HOST_CONTROL2 register is a part of SDHC v3.00 and not just specific
to arasan/zynq controllers. Add the same to sdhci.h.

Also create a common API to set UHS timings in HOST_CONTROL2.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17 11:12:08 -04:00
Faiz Abbas
ce142ff0c5 mmc: am654_sdhci: Add Support for PHY
Add support in the driver for handling phy specific registers.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17 11:12:08 -04:00
Faiz Abbas
a8185c50d3 mmc: sdhci: Make set_ios_post() return int
Make set_ios_post() return int to faciliate error handling in
platform drivers.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-07-17 11:12:08 -04:00
Faiz Abbas
3966c7d006 mmc: sdhci: Make sdhci_set_clock() non static
The am654_sdhci driver needs to switch the clock off
before disabling its phy dll and needs to re-enable
the clock before enabling the phy again.

Therefore, make the sdhci_set_clock() function accessible
in the am654_sdhci driver.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17 11:12:08 -04:00
Faiz Abbas
3d296365e4 mmc: sdhci: Add support for sdhci-caps-mask
Add Support for masking some bits in the capabilities
register of a host controller.

Also remove the redundant readl() into caps1.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17 11:12:08 -04:00
Faiz Abbas
6fca7fb3a0 mmc: am654_sdhci: Remove quirks
The host controller works perfectly well without having to add any
quirks. Remove them.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17 11:12:08 -04:00
Faiz Abbas
3a1a0dfc39 arm64: dts: k3: Sync sdhci0 node from kernel and change driver name
Sync the sdhci0 node from kernel. This changes the compatible that is
required to be there in the driver. Change the same for the SD card node
which is not yet supported in kernel. This also syncs the main_pmx0 node
as a side effect.

Also change the name of the driver to match the compatible in kernel.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17 11:12:08 -04:00
Tom Rini
6674dc77c2 Merge tag 'mmc-2019-7-15' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmc
- mmc spi driver model support
- drop mmc_spi command
- enhanced Strobe mmc HS400 support
- minor mmc bug/fixes and optimization
- omap hsmmc and mvbeu update
- sdhci card detect support
2019-07-15 09:42:41 -04:00
Peng Fan
356f782c6e mmc: fsl_esdhc_imx: enlarge mmc timeout
Flash system partition with fastboot will earse the partition firstly
The 600ms timeout will fail on some SD Card. Enlarge it to 5s to make
it works for most of sdcard

Cc: guoyin.chen <guoyin.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-15 10:30:09 +08:00
Peng Fan
609ba125c5 mmc: fsl_esdhc_imx: add i.MX8QM compatible
Add i.MX8QM compatible and soc data, the soc data is following Linux
i.MX SDHC driver.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-15 10:30:09 +08:00
Peng Fan
e9c2255267 mmc: fsl_esdhc_imx: add HS400 Enhanced strobe support
Implement set_enhanced_strobe hook for fsl_esdhc_imx,
,in esdhc_set_timing and esdhc_change_pinstate, also handle HS400_ES.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-15 10:30:09 +08:00
Peng Fan
b0155ac63c mmc: fsl_esdhc_imx: use mmc_of_parse to set host_caps
Use mmc_of_parse to set host_caps.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-15 10:30:09 +08:00
Peng Fan
479a8dd6dc mmc: Parse no-1-8-v DT property
Parse no-1-8-v DT

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
2019-07-15 10:30:08 +08:00
Peng Fan
b0fc3127bd mmc: Parse HS400 Enhanced strobe DT properties
Add HS400 Enhanced strobe properties parsing support to mmc_of_parse().

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
2019-07-15 10:30:08 +08:00
Peng Fan
44acd49248 mmc: support hs400 enhanced strobe mode
eMMC 5.1+ supports HS400 Enhances Strobe mode without the need for
tuning procedure.
The flow is as following:
 - set HS_TIMIMG (Highspeed)
 - Host change freq to <= 52Mhz
 - set the bus width to Enhanced strobe and DDR8Bit(CMD6),
   EXT_CSD[183] = 0x86 instead of 0x80
 - set HS_TIMING to 0x3 (HS400)
 - Host change freq to <= 200Mhz
 - Host select HS400 enhanced strobe complete

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-15 10:30:08 +08:00
Ye Li
8277171663 mmc: fsl_esdhc_imx: fix config check issue when building in SPL
Should use CONFIG_IS_ENABLED not IS_ENABLED for clock and regulator drivers,
CONFIG_IS_ENABLED will check the CONFIG_SPL_CLK and CONFIG_SPL_DM_REGULATOR
when building SPL.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-15 10:30:08 +08:00
Bhargav Shah
05e35d4297 mmc: mmc_spi: Re-write driver using DM framework
This patch rewrites MMC SPI driver using U-Boot DM
framework and get it's working on SiFive Unleashed
board.

Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-15 10:16:49 +08:00
Anup Patel
f49ff79935 mmc: skip select_mode_and_width for MMC SPI host
The MMC mode and width are fixed for MMC SPI host hence we skip
sd_select_mode_and_width() and mmc_select_mode_and_width() for
MMC SPI host.

Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
0538477c53 mmc: retry a few times if a partition switch failed
This operation may fail. Retry it a few times before giving up and report
a failure.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
9bc5666c8a mmc: do not change mode when accessing a boot partition
Accessing the boot partition had been error prone with HS200 and HS400 and
was disabled. The driver first switched to a lesser mode and then switched
the partition access. It was mostly due to a bad handling of the switch and
has been fixed, so let's remove this 'feature'

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
bb98b8c5c0 mmc: During a switch, poll on dat0 if available and check the final status
The switch operation can sometimes make the bus unreliable, in that case
the send_status parameter should be false to indicate not to poll using
CMD13. If polling on dat0 is possible, we should use it to detect the end
of the operation.
At the end of the operation it is safe to use CMD13 to get the status of
the card. It is important to do so because the operation may have failed.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
513e00b64e mmc: When switching partition, use the timeout specified in the ext_csd
The e-MMC spec allows the e-MMC to specify a timeout for the partition
switch command. It can take up to 2550 ms. There is no lower limit to this
value in the spec, but do as the the linux driver does and force it to be
at least 300ms.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
39320c537d mmc: use the generic timeout for cmd6 (SWITCH) provided in the ext_csd
Starting with rev 4.5, the eMMC can define a generic timeout for the
SWITCH command.

Following Linux Kernel code, the timeout also changed from 1000 -> 500

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
cd0b80ec9c mmc: if possible, poll the busy state using DAT0
Using the DAT0 line as a rdy/busy line is an alternative to reading the
status register of the card. It especially useful in situation where the
bus is not in a good shape, like when modes are switched.
This is also how the linux driver behaves.

Note of warning: As per the specification, while polling on DAT0 the CLK
must not turned off: "[...] Without a clock edge the Device (unless
previously disconnected by a deselect command (CMD7)) will force the DAT0
line down, forever. [...]"

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
863d10044a mmc: add mmc_poll_for_busy() and change the purpose of mmc_send_status()
mmc_send_status() is currently used to poll the card until it is ready, not
actually returning the status of the card.
Make it return the status and add another function to poll the card.

Also remove the 'extern' declaration in the mmc-private.h header to comply
with the coding standard.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
c2c22b9df3 mmc: omap_hsmmc: provide wait_dat0 even if UHS modes are not supported
This function can also be used for eMMC devices.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
c5bda37589 Revert "mmc: Add a new callback function to perform the 74 clocks cycle sequence"
This reverts commit 318a7a576b.

The last and only user of this callback had been the omap_hsmmc driver.
It is not used anymore. Removing the callback.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
db52e19ced mmc: omap_hsmmc: don't fill the send_init_stream callback
This is not required. The MMC core sends CMD0 right after the
initialization and it serves the same purpose.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
b2ffa3320a mmc: omap_hsmmc: reset FSM for DAT and CMD lines if needed before a new command
It sometimes happen that the PSTATE register does not indicate that the
bus is ready when it really is. This usually happens after a mode switch.
In that case it makes sense to reset the FSM handling the CMD and DATA

Also reset the FSMs if the STATE register cannot be cleared. This also
sometimes happens after a mode switch.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Akio Hirayama
24b1e0c7e2 mmc: rpmb: fix response type of CMD25
The response type of CMD25 is R1 instead of R1b.

Signed-off-by: Akio Hirayama <hirayama.akio@socionext.com>
[masahiro: add log ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-07-15 10:16:49 +08:00
T Karthik Reddy
da18c62b6e mmc: sdhci: Implement SDHCI card detect
Card detect function implemented for SDHCI framework.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-15 10:16:49 +08:00
T Karthik Reddy
451931ea70 mmc: sdhci: Read cd-gpio from devicetree
This patch reads cd-gpio property from devicetree

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-07-15 10:16:49 +08:00
T Karthik Reddy
86a94e7b2b mmc: Read sd card detect properties from DT
This patch reads card detect properties from device tree &
added mmc capability macros in mmc.h.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-15 10:16:49 +08:00
Tom Rini
a9a3a37f92 - syscon: add support for power off
- stm32mp1: add op-tee config
 - stm32mp1: add specific commands: stboard and stm32key
 - add stm32 mailbox driver
 - solve many stm32 warnings when building with W=1
 - update stm32 gpio driver
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJdKK2iAAoJEOKyvdngqpN1TvcH/jj1ujNdRKn994R3DqULzFtc
 Y0WGjAciTUuV0d9gZLxPZJwlWfqxLgbmUEBlPJQJe79gaM7kNN0PgAe6GNedFhGk
 UhRR7GgbA7wogorpRo8aLe3XYEqHtgPFkf1nSiNz/AHLBg8SB20VhWcY90Kha9lh
 IJ0GK+lSdCxiyaLBC2nswnI2PS/fl4NfC7KWvujtKZduIDIOHqh5q+39llpejyuw
 WOzL/bEa4ald6JKpxOii2KXNwD1gUDQGmPzADYcIdwzJtx9hft7DBSLC5Nr+ndBz
 72TjpbtfJ/qIurv8HeXYs9mtwnCO3WP+015fog0T0zjZ48BrT1A8C96ezwLOfz0=
 =W3ny
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20190712' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm

- syscon: add support for power off
- stm32mp1: add op-tee config
- stm32mp1: add specific commands: stboard and stm32key
- add stm32 mailbox driver
- solve many stm32 warnings when building with W=1
- update stm32 gpio driver
2019-07-14 09:09:49 -04:00
Ezequiel Garcia
d66fb5b1f6 mmc: Register only the first MMC device on MMC_TINY
When MMC_TINY is enabled, support for only one MMC device
is provided. Boards that register more than one device,
will just write over mmc_static keeping only the last one
registered.

This commit prevents this, keeping only the first MMC
device created. A debug warning message is added, if nothing
else, as a hint/documentation for developers.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
2019-07-13 11:11:26 -04:00
Ezequiel Garcia
bf7c01d92b spl: Move SPL_MMC_TINY option to appear under SPL menu
The SPL_MMC_TINY implements feature-reduced MMC support
on SPL, and as such, it's more consistent and convenient
to find it as part of the SPL configuration.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
2019-07-13 11:11:26 -04:00
Patrick Delaunay
0e9fb25f71 mmc: stm32_sdmmc2: avoid warnings when building with W=1 option
This patch solves warnings detected by setting W=1 when building.

Warnings type detected:
 - [-Wmissing-prototypes]
 - [-Wimplicit-fallthrough=]

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:50:54 +02:00
Yangbo Lu
5053da2e4a mmc: fsl_esdhc_imx: drop useless code
Dropped useless code for i.MX eSDHC driver.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-06-23 14:18:48 +08:00
Yangbo Lu
4d8ff42e46 mmc: fsl_esdhc: drop i.MX code
Dropped i.MX code which couldn't be reused.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
2019-06-23 14:18:42 +08:00
Yangbo Lu
fa33d20749 mmc: split fsl_esdhc driver for i.MX
The fsl_esdhc driver was for Freescale eSDHC on MPC83XX/MPC85XX
initially. The later QoriQ series PowerPC processors (which were
evolutions of MPC83XX/MPC85XX), QorIQ series ARM processors, and
i.MX series processors were using this driver for their eSDHCs too.

For the two series processors, the eSDHCs are becoming more and
more different. We should have split it into two drivers, like them
(sdhci-of-esdhc.c/sdhci-esdhc-imx.c) in linux kernel.

This patch is just to create a fsl_esdhc_imx driver which is a copy
of fsl_esdhc driver for i.MX processors. We will convert i.MX processors
to use fsl_esdhc_imx, and clean up the two drivers separately in the
future patches.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
2019-06-23 14:15:31 +08:00
Tom Rini
64fabed971 Merge tag 'mmc-6-19' of https://github.com/MrVan/u-boot
- Avoid HS400 mode when accessing boot partitions
2019-06-20 09:13:27 -04:00
Yangbo Lu
66fa035b55 mmc: fsl_esdhc: fix probe issue without CONFIG_BLK enabled
u-boot is trying to make CONFIG_BLK as a hard requirement
for DM_MMC. But now it's still not.

config BLK
	bool "Support block devices"
	depends on DM
	default y if DM_MMC

When fsl_esdhc driver was reworked for DM_MMC support, DM_MMC
without CONFIG_BLK enabled wasn't considered. This patch is to
fix probe issue without CONFIG_BLK enabled.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19 12:54:56 +05:30
Marek Vasut
72119aa14a mmc: Avoid HS400 mode when accessing boot partitions
U-Boot code currently only applies this restriction to HS200 mode,
extend this to HS400 mode as well.

Currently U-Boot code not support accessing boot partition in HS200/400
mode. This needs more check.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-06-19 13:53:59 +08:00
Thomas Fitzsimmons
77934fdedf dm: arm: bcmstb: Enable driver model MMC support
For bcm7445 and bcm7260, this patch enables CONFIG_DM_MMC and updates
the bcmstb SDHCI driver to use the new driver model.  This allows
removal of SDHCI configuration handling from bcmstb.c, and eliminates
a board removal compile warning.

Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2019-05-28 13:58:06 -04:00
Tom Rini
c18b103657 Merge branch 'master' of git://git.denx.de/u-boot-sh
- Gen3 PCIe driver + enablement on Salvator-X platforms.
- Gen3 recovery SPL used to reload ATF/OpTee/U-Boot instead of minimon.
- SDHI HS400 fixes ported from latest BSP and datasheet.
2019-05-26 20:18:20 -04:00
Yinbo Zhu
b69e1d0bc7 driver: mmc: adopt 32 bit addr in fsl_esdhc for CONFIG_PPC
PowerPC supports 32 bit address.
So adopt 32 bit addr in fsl_esdhc for CONFIG_PPC.

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-05-23 14:22:33 +05:30
Yinbo Zhu
b512d07e8c driver: mmc: set sdhc clock in fsl_esdhc for CONFIG_PPC
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-05-23 14:22:33 +05:30
Marek Vasut
b5900a58ca mmc: tmio: sdhi: HS400 manual adjustment
Since Gen3 SDHI has an internal DS signal AC-spec violation in HS400 mode,
CRC-error may occur in read command in HS400 mode. This phoenomenon occurs
at low/high temperature.

To fix this, after completion of HS400 tuning, enable manual calibration.
However, Gen3 M3 Ver.1.2 or earlier and H3 1.x does not support HS400.
These SoC forcibly use HS200 mode by SoC attribute.

The DT adjustment of the tuning parameters is not supported until the
DT property names become clear.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Adapted from a patch by Takeshi Saito <takeshi.saito.xv@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Peng Fan <peng.fan@nxp.com>
2019-05-21 22:15:32 +02:00