The 'xtfpga' board is actually a set of FPGA evaluation boards that
can be configured to run an Xtensa processor.
- Avnet Xilinx LX60
- Avnet Xilinx LX110
- Avnet Xilinx LX200
- Xilinx ML605
- Xilinx KC705
These boards share the same components (open-ethernet, ns16550 serial,
lcd display, flash, etc.).
Signed-off-by: Chris Zankel <chris@zankel.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add Kconfig entry for the driver, remove #define CONFIG_ETHOC from the
only board configuration that uses it and put it into that board's
defconfig.
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use the right phy_connect() prototype for CONFIGF_DM_ETH.
Support to get the phy interface from dt and set GMAC_UR.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Trimslice currently stores its environment at 512KiB into the SPI flash
chip. The U-Boot binary has grown such that the size of the boot image
(which includes the Tegra BCT, padding, and the U-Boot binary) is slightly
larger than 512K now. Consequently, writing the boot image to flash
corrupts the saved environment, and equally, writing to or erasing the
environment will corrupt the bootloader, which in turn will cause the
Tegra boot ROM to enter recovery mode during boot, making it look as if
the system is non-operational. Note that tegra-uboot-flasher writes to
the environment during the flashing process.
Solve this by moving the environment as high as possible in flash. This
will allow the U-Boot binary to roughly double in size before this problem
is hit again, at which point there's nothing we can do anyway since the
binary won't fit into flash.
99% of other Tegra boards store the environment in eMMC and use a negative
value for CONFIG_ENV_OFFSET, which already automatically places the
environment as near the end of boot flash as possible. The 1 remaining
board hard-codes CONFIG_ENV_OFFSET to 2MiB, which allows for plenty more
bloat.
Reported-by: Stephen L Arnold <nerdboy@gentoo.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
p2771-0000 has a couple of PCIe ports; one physically x4 desktop PCI
connector (which may run at x2 electrically, depending on the board
version and configuration) and a x1 connection to the M.2 slot (which may
not be active, depending on the board version and configuration). This
change enables those.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The UniPhier outer cache (L2 cache on ARMv7 SoCs) has 128 byte line
length and its tags are also managed per 128 byte line.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move this option to Kconfig, renaming it into CONFIG_CACHE_UNIPHIER.
The new option name makes sense enough, and the same as Linux has.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The devicetrees for various platforms already exceed 16k. Add a define
CONFIG_SYS_FDT_SIZE to specify the FDT size, and set to 16k for the
two boards that define this CONFIG_SYS_FDT_BASE parameter. This
allows platforms with larger devicetree blobs to boot from NOR.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
The meaning of CONFIG_USB in U-Boot is different from that in Linux.
As you see in drivers/usb/Kconfig of Linux, CONFIG_USB enables the
USB host controller support, while CONFIG_USB_SUPPORT is used to
enable the whole of the USB sub-system.
When I added CONFIG_USB into Kconfig by commit 6e7e9294d3 ("usb:
add basic USB configs in Kconfig"), I planned to follow the Linux's
convention, i.e. CONFIG_USB to enable/disable the USB host support.
Then, commit 68f7c5db2d ("usb: Generic USB Kconfig option, that
fits both host and gadget and comments") changed the logic of the
CONFIG_USB to point to the whole of the USB sub-system. As a result,
currently we do not have an option for USB host.
This commit adds CONFIG_USB_HOST, which will be useful to compile
in the USB host support code.
CONFIG_USB_HOST is not referenced at all, but strangely some boards
define it in board headers. I removed them because USB_HOST will be
selected in Kconfig going forward.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This follows 9fd383724c ("mmc: don't allow extra cmdline arguments"),
and affects omapl138_lcdk and omap3_evm_quick_mmc.
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These config targets were added well before the Kconfig migration began
as a way to demonstrate how to make these platforms work with cut down
features. At this point in time they no longer serve a good purpose so
remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable the rockchip dwmmc driver for rk3399 and its evb.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
To compatible with distro boot, we need to add gpt and fs support,
including gpt table and vfat, ext2, ext4 support.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Enable ums feature for rk3288 boards, so that we can mount the mmc
device to PC.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
For compatibility with distro boot, fastboot, and mount the mmc deivce
to PC via usb mass storage feature, GPT partitions are essential.
You should write the partitions to mmc device prior to use above
feature.
=> gpt write mmc 1 $partitions
GPT successfully written to block device!
success!
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Miniarm is a rockchip rk3288 based development board, which has lots of
interface such as HDMI, USB, micro-SD card, Audio etc.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable fastboot feature on rk3036, please refer to doc/README.rockchip
for more detailed usage.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system. Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.
Ravi Babu reported offset mismatch of struct dwc3 across files since
commit 95ebc253e6 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.
I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable. However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones. I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.
CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.
Fixes: 95ebc253e6 ("types.h: move and redefine resource_size_t")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As of now we have 2 flavors of ARC SDP boards:
1) AXS101 - with ARC770 in ASIC
2) AXS103 - with ARC HS38 in FPGA
Both options share exactly the same base-board and only differ with
CPU-tiles in use. That means all peripherals are the same (they are
implemented in FPGA on the base-board) and so generic board could be
used for both.
While at it:
* Recreated defconfigs with savedefconfig
* In include/configs/axs10x.h numerical sizes replaced with
defines from linux/sizes.h for better readability.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
ARCangel was one of the main development boards back in the day but
now it's gone and replaced by other boards like ARC SDP.
But we also used to have simulation platform very similar to ARCangel4
in terms of CPU settings as well as basic IO like UART. Even though
ARCangel4 is long gone now we have a replacement for simulation which is
a plain or stand-alone nSIM and Free nSIM.
Note Free nSIM is available for download here:
https://www.synopsys.com/cgi-bin/dwarcnsim/req1.cgi
And while at it:
* Finally switch hex numerical values in nsim.h to defines from
include/linux/sizes.h
* Add defconfigs with ARC HS38 cores
* Recreated all defconfigs with savedefconfig
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This is what Linux maps on classic PPC during boot, and modern kernel
images don't fit within the current 8 MiB uncompressed limit.
Adjust image load addresses to be above this limit to avoid conflicts.
Signed-off-by: Scott Wood <oss@buserror.net>
Reviewed-by: York Sun <york.sun@nxp.com>
The PPA binary may be stored on QSPI flash instead of NOR.
So, deprecated CONFIG_SYS_LS_PPA_FW_IN_NOR in favour of
CONFIG_SYS_LS_PPA_FW_IN_XIP to prevent fragmentation of code
by addition of a new QSPI specific flag.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
qixis_reset altbank usagge ~QIXIS_LBMAP_MASK in code. So define
inverse value QIXIS_LBMAP_MASK.
Also, update QIXIS_RST_CTL_RESET value to keep RST_CTL[REQ_MOD]
as 0b11 i.e. PORESET during qixis_reset
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PopMetal is a rockchip rk3288 based board made by ChipSpark, which has
many interface such as HDMI, VGA, USB, micro-SD card, WiFi, Audio and
Gigabit Ethernet.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fennec is a RK3288-based development board with 2 USB ports, HDMI,
micro-SD card, audio and WiFi and Gigabit Ethernet. It also includes
on-board 8GB eMMC and 2GB of SDRAM. Expansion connectors provides access
to display pins, I2C, SPI, UART and GPIOs.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The 'evb-rk3288' is not a vendor name, change it to 'rockchip' which is
the real vendor name.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_SYS_LOAD_ADDR is absolutely safe to store image for
fastboot.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_DOS_PARTITION and CONFIG_EFI_PARTITION are already included in
config_distro_defaults.h, and we don't need them in SPL stage.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The CONFIG_ROCKCHIP_COMMON and CONFIG_SPL_ROCKCHIP_COMMON are no use now,
remove them.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
AM571x IDK and AM572x IDK EVMs have spansion s25fl256s QSPI flash on the
board connected to TI QSPI IP over CS0. Therefore enable QSPI support.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Now that QSPI driver can support 76.8MHz, update the
CONFIG_SF_DEFAULT_SPEED to the same value.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Use CONFIG_TIMER_CLK_FREQ to let the non-secure init code initialize
the generic timer on all CPU's. This allows to make use of the timer
freuquency register also on other CPU than the start CPU which is
important for KVM.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
cgtqmx6eval uses the imx_ddr_size() function to calculate the DDR size in
runtime, so there is no need to define PHYS_SDRAM_SIZE.
Remove the unneeded definition.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
novena uses the imx_ddr_size() function to calculate the DDR size in
runtime, so there is no need to define PHYS_SDRAM_SIZE.
Remove the unneeded definition.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Marek Vasut <marex@denx.de>
imx_ddr_size() can be used to calculate the DDR size in runtime.
By using this function we no longer need to define PHYS_SDRAM_SIZE.
Cc: Martin Donnelly <martin.donnelly@ge.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
imx_ddr_size() can be used to calculate the DDR size in runtime.
By using this function we no longer need to define PHYS_SDRAM_SIZE.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Heiko Schocher <hs@denx.de>
imx_ddr_size() can be used to calculate the DDR size in runtime.
By using this function we no longer need to define PHYS_SDRAM_SIZE.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently it's recommended to move some configuration options to the
defconfig file.
Move some USB related options to the defconfig file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
