Add a helper function that will return a phandle value for the given
node. If the node doesn't have a phandle already one will be created.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
The old fdt_create_phandle didn't actually create a phandle it just
set one. We'll introduce a new helper that actually does creation.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
And various defines to enable NAND support and NAND spl code for the
P1010RDB platform.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Boot methods supported: NOR Flash, SPI Flash and SDCARD
This patch adds the following basic interfaces:
DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash.
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
Local Bus (IFC):
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
64KB CPLD device(GPCM interface)
SPI Flash:
128 Mbit SPI Flash memory
SD/MMC:
connector to interface with the SD memory card
SATA:
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0:
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC:
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221
eCAN:
Two DB-9 female connectors for Field bus interface
UART:
supports two UARTs up to 115200 bps for console
TDM:
2 FXS ports connected via an external SLIC to the TDM interface.
SLIC:
SPI SLIC
I2C:
Serial EEprom
Real time clock
256 Kbit M24256 I2C EEPROM
PCIe:
PCIe and mPCIe connectors.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following boards share a common design but with minor variations
between them:
P1020MSBG-PC
P1020RDB-PC
P1020UTM-PC
P1021RDB-PC
P1024RDB
P1025RDB
P2020RDB-PC
The P1020RDB-PC shares its roots in the existing P1020RDB board design,
however uses DDR3 instead of DDR2.
P2020RDB-PC differs from the P102x RDB-PC with 64-bit DDR and 100Mhz SYSCLK.
Key features on these boards include:
* DDR3
* NOR flash
* NAND flash (on RDB's only)
* SPI flash (on RDB's only)
* SDHC/MMC card slot
* VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB)
* PCIE slot and mini-PCIE slots
As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM
is used to store SPD data. In case of absent or corrupted SPD, falling back
to timing data embedded in the source code will be used. Raw timing data is
extracted from DDR chip datasheet. Different speeds of DDR are supported
with this approach. ODT option is forced to fit this set of boards, again
because they don't have regular DIMMs.
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet
specification for writing timing.
VSC firmware Address is defined by default in config file for eTSEC1.
SD width is based off DIP switch. DIP switch is detected on the
board by reading i2c bus and setting the appropriate mux values.
Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC
have pins multiplexing. QE function needs to be disabled to access Nor Flash
and CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe"
in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to
enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below
'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD.
'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Zhao Chenhui <b26998@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: ramneek.mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Akhil Goyal <akhil.goyal@freescale.com>
Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.
CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file. Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.
CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.
Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. the "real" U-Boot). All other stages should define
CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated.
README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The few tests that are Blackfin-specific have been migrated to common
code or been rewritten with the existing "bsp-specific" defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There is no code anywhere that references BOOTFLAG_* so remove these
defines.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Result of running the following command to address Wolfgang's
comment about camel case:
for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done
Discussion:
http://patchwork.ozlabs.org/patch/84988/
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Factor out common parts from omap4_sdp4430.h and omap4_panda.h
into a new file omap4_common.h
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Modify the MEMTEST start and end address. The memtest range was overlapping the
CONFIG_SYS_LOAD_ADDR which causes the uImage to be corrupt.Also, modify the
size for which mtest is run to 32MB from 16MB.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Enable SPI flash boot mode in configuration file as default.
With the introduction of 456MHz part, SPI operating frequency
will increase and at this frequency SPI does not work correctly.
Hence reduce the default SPI speed to 30MHz from 50MHz.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Modify U-boot promt string from 'DA830-evm >' to 'U-Boot >' as
there are many variants of da830 based boards which have diffrent
names such as L137, AM1707 etc.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Make use of GPIO framework and avoid the following build error:
tx25.c: In function 'tx25_fec_init':
tx25.c:73: error: dereferencing pointer to incomplete type
tx25.c:74: error: dereferencing pointer to incomplete type
tx25.c:75: error: dereferencing pointer to incomplete type
tx25.c:76: error: dereferencing pointer to incomplete type
tx25.c:83: error: dereferencing pointer to incomplete type
tx25.c:84: error: dereferencing pointer to incomplete type
tx25.c:114: error: dereferencing pointer to incomplete type
tx25.c:115: error: dereferencing pointer to incomplete type
tx25.c:116: error: dereferencing pointer to incomplete type
tx25.c:117: error: dereferencing pointer to incomplete type
tx25.c:124: error: dereferencing pointer to incomplete type
tx25.c:125: error: dereferencing pointer to incomplete type
tx25.c:126: error: dereferencing pointer to incomplete type
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch fixes the warning dure to recent changes to the board
configuration:
cmd_i2c.o cmd_i2c.c -c
cmd_i2c.c:109:1: warning: missing braces around initializer
cmd_i2c.c:109:1: warning: (near initialization for 'i2c_no_probes[0]')
Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Acked-by: Jason Kridner <jdk@ti.com>
Fix these:
cm4008.c: In function 'board_eth_init':
cm4008.c:79: warning: implicit declaration of function 'ks8695_eth_initialize'
cm41xx.c: In function 'board_eth_init':
cm41xx.c:79: warning: implicit declaration of function 'ks8695_eth_initialize'
While we are at it, sort include list in netdev.h
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Greg Ungerer <greg.ungerer@opengear.com>
Commit 21726a7 "Add assert() for debug assertions" caused build
warnings for many systems:
In file included from bedbug.c:6:
/home/wd/git/u-boot/work/include/bedbug/bedbug.h:24:1: warning: "assert" redefined
In file included from bedbug.c:3:
/home/wd/git/u-boot/work/include/common.h:144:1: warning: this is the location of the previous definition
In file included from cmd_bedbug.c:10:
/home/wd/git/u-boot/work/include/bedbug/bedbug.h:24:1: warning: "assert" redefined
In file included from cmd_bedbug.c:5:
/home/wd/git/u-boot/work/include/common.h:144:1: warning: this is the location of the previous definition
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
The OpenGear boards CM4008, CM4116 and CM4148 need their DRAM base
and RAM stack base addresses defined.
Fixes:
board.c: In function ‘__dram_init_banksize’:
board.c:227: error: ‘CONFIG_SYS_SDRAM_BASE’ undeclared (first use in this function)
board.c:227: error: (Each undeclared identifier is reported only once
board.c:227: error: for each function it appears in.)
board.c: In function ‘board_init_f’:
board.c:270: error: ‘CONFIG_SYS_INIT_SP_ADDR’ undeclared (first use in this function)
board.c:303: error: ‘CONFIG_SYS_SDRAM_BASE’ undeclared (first use in this function)
Signed-off-by: Greg Ungerer <greg.ungerer@opengear.com>
assert() is like BUG_ON() but compiles to nothing unless DEBUG is defined.
This is useful when a condition is an error but a board reset is unlikely
to fix it, so it is better to soldier on in hope. Assertion failures should
be caught during development/test.
It turns out that assert() is defined separately in a few places in U-Boot
with various meanings. This patch cleans up some of these.
Build errors exposed by this change (and defining DEBUG) are also fixed in
this patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently when you call ROUND with a value that is already a
multiple of the second parameter it will return a value that is
one multiple larger, instead of returning the value passed in.
There are only two types of usage of ROUND currently, one in
various config files to round CONFIG_SYS_MALLOC_LEN to a multiple
of 4096 bytes. The other in cmd_sf.c where the incorrect behavior
of ROUND is worked around be subtracting one from the length argument
before passing it to ROUND.
This patch fixes ROUND and removes the workaround from cmd_sf. It
also results in all of the malloc pools that use ROUND to compute
their size shrinking by 4KB.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
The Lattice code was missed by commit e6a857d "fpga: constify to fix
build warning" resulting in such warnings:
fpga.c: In function 'fpga_load':
fpga.c:238: warning: passing argument 2 of 'lattice_load' discards qualifiers from pointer target type
fpga.c: In function 'fpga_dump':
fpga.c:278: warning: passing argument 2 of 'lattice_dump' discards qualifiers from pointer target type
Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Stefano Babic <sbabic@denx.de>
* 'master' of git://git.denx.de/u-boot-coldfire:
ColdFire:Clean up the CONFIG_STANDALONE_LOAD_ADDR usage
ColdFire:Add mb for 5253 dram initialization
ColdFire:Define the DM9000 byteswap for M5253 board.
ColdFire:Update the env settings for several boards.
ColdFire:disable the NFS define for 52277 board.
ColdFire:Update the timer_init since it was unified.
ColdFire: Cleanup for partial linking and --gc-sections
ColdFire: Update compile flags for each CPUs
ColdFire:Fix the configuration broken for some boards.
The M5253DEMO board swapped the io pins which make
the standard IO function did not work for dm9000.
Define the byte swap to use raw io for dm9000.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Move the environment outside the u-boot for some boards
and enlarge the u-boot size in some env settings.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
There is no network device on ColdFire 52277EVB board.But the default
cmd include NFS define which make the build error.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
* Improved boot env var setting
* Made room for a 64MB ramdisk by moving from 0x81600000 to 0x81000000
* Added ramarg, ramroot and ramboot env variables
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
buddy and camera are used to configure peripherals in the kernel at boot
time that cannot easily be detected by the kernel.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Utilize the alternate mtest and define a valid region.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Based on commit f1099c7c43caf5bac3bf6a65aa266fade4747072
Author: Greg Turner <gregturner@ti.com>
Date: Tue May 25 09:19:06 2010 -0500
New u-boot command for status of USER button on BeagleBoard-xM
Modified bootcmd to check the staus at boot time and set
filename of the boot script.
* Moved to a BeagleBoard specific file.
* Removed changes to default boot command from adding userbutton
command.
* Made to handle pre-xM boards.
* Flipped polarity of the return value to avoid confusion. Success (0)
is when the button is pressed. Failure (1) is when the button is NOT
pressed.
* Used latest revision getting function.
* Used latest macros for board revision.
* Added xM-C revision definition (optional, since it was default)
* updated default configuration with UserButton functionality
* Added a separate bootenv variable to load a user defined .txt file
* Added an example, showing how a different environment file can be loaded with
the user button pressed
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Cc: Greg Turner <gregturner@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The kernel DSS2 code is mature now, and keeping this setting hurts performance
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The AM18xx EVM contains winbond SPI flash instead of ST SPI flash in
comparison with logic PD da850/omap-l138 EVM. So enable configuration
to look for winbond flash.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
add support for DSP wake-up by default on DA850/OMAP-L138
during board initialization. Enable hwconfig environment and added
extra env setting through CONFIG_EXTRA_ENV_SETTINGS.
To prevent DSP from being woken up,set the environment variable as,
set hwconfig "dsp:wake=no"
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add pin-mux support for NOR in board file and correspanding
macros to use NOR boot mode in configuration file.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
there are cache coherency issues when using the DAVINCI Ethernet driver,
hence caches cant be used for da850 u-boot. As per new cache management
framework,if the caches are not used in u-boot, it needs to be explicitly
indicated through macros in config file. CACHE disable is indicated by
the following macro definitions in config file,
1. CONFIG_SYS_ICACHE_OFF
2. CONFIG_SYS_DCACHE_OFF
3. CONFIG_SYS_L2CACHE_OFF
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Newer version for DM365 silicon support higher speeds
and is called DM368. Modify the bootprompt string DM365
to DM36x.
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
there are cache coherency issues when using the DAVINCI Ethernet driver,
hence caches cant be used for d365 u-boot. As per new cache management
framework,if the caches are not used in u-boot, it needs to be explicitly
indicated through macros in config file. CACHE disable is indicated by
the following macro definitions in config file,
1. CONFIG_SYS_ICACHE_OFF
2. CONFIG_SYS_DCACHE_OFF
3. CONFIG_SYS_L2CACHE_OFF
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
there are cache coherency issues when using the DAVINCI Ethernet driver,
hence caches cant be used for dm6446 u-boot. As per new cache management
framework,if the caches are not used in u-boot, it needs to be explicitly
indicated through macros in config file. CACHE disable is indicated by
the following macro definitions in config file,
1. CONFIG_SYS_ICACHE_OFF
2. CONFIG_SYS_DCACHE_OFF
3. CONFIG_SYS_L2CACHE_OFF
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy mmc driver to the
new generic mmc driver.
This patch is based on similar patch for beagle[1].
[1] http://git.denx.de/?p=u-boot.git;a=commitdiff_plain;h=0cd31144240
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy mmc driver to the
new generic mmc driver.
This patch is based on similar patch for beagle[1].
[1] http://git.denx.de/?p=u-boot.git;a=commitdiff_plain;h=0cd31144240
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Increase the console I/O buffer size (SYS_CBSIZE) to 512 (from 256)
required especially for bootargs string, as multiple options
(e.g Video settings) are passed to the kernel through bootargs.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
c2dd0d4554 added dcache_enable()
to board_init_r(). This enables d-cache for all ARM boards.
As a result some of the arm boards that are not cache-ready
are broken. Revert this change and allow platform code to
take the decision on d-cache enabling.
Also add some documentation for cache usage in ARM.
Signed-off-by: Aneesh V <aneesh@ti.com>
Origen board is based upon S5PV310 SoC which is similiar to
S5PC210 SoC.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
IMX processors has a slightly different interface
to access GPIOs and do not make use of the provided GPIO
framework. The patch substitutes mxc_ specific
functions and make use of the API in asm/gpio.h
Signed-off-by: Stefano Babic <sbabic@denx.de>
CONFIG_L2_OFF is obsolete after the following commit:
e47f2db537
armv7: rename cache related CONFIG flags
Replace the cache related CONFIG flags with more meaningful
names. Following are the changes:
CONFIG_L2_OFF -> CONFIG_SYS_L2CACHE_OFF
Since imx5 does not provide L2 cache operations(Enable/Disable)
Simply remove CONFIG_L2_OFF and CONFIG_SYS_L2CACHE_OFF
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc:Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This deletes the integrator split_by_variant.sh script and
defines a number of unique board types for the core modules
that are meaningful to support for the Integrator AP/CP, i.e.
the ones that did not just say "unsupported core module" in
split_by_variant.sh. If more core modules need to be supported
they are easy to add.
We delete all the old cruft in Makefile and MAKEALL that was
working around the old way of building boards. We create a
unique config file per board to satisfy the build system, but
they are just oneliners that include the existing
integratorap.h and integratorcp.h configs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The default configuration for the Integrator AP forces memory to be
32 MB on the command line to the kernel, while we have perfect
information and detection of the actual memory size in the ATAGs.
Delete the confusion.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for a subset of the default commands for the
Integrator, however since the card does not have Ethernet (unless
you plug in a PCI card) we can not use the default command set.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The integrator board was apparently never converted over to support
relocation until now. After this the integrator u-boot both compiles
and boots on the Integrator AP.
This also fixes the SDRAM memory size detection.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The integratorap/cp config for u-boot was outdated and would not
even compile, so fix the obvious missing bits for it to start
building. After this "make ap920t_config/make all" starts working
again.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Innovator and H2 boards used machine_is_* macros for setting the machine
type. These macros are expanded in compile time and thus leaves
unreachable code (though gcc might optimize it).
Switch them to use common code for machine type setting.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
NVIDIA boards and Samsung SMDK6400 already use a local variant of
CONFIG_MACH_TYPE option.
Switch to use the new common code.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
The meesc board support was broken. Within this opportunity, I completely
reworked the board files.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Signed-off-by: Matthias Fuchs <Matthias.Fuchs@esd.eu>
Adjusted default settings so that we can boot zImages and uImages.
Removed unused settings, use default commands and where possible
calculate all other settings.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The rsk7264 (also know as rsk2+sh7264) is an SH2A based board
with 64MB NAND flash and 64MB SDRAM. It is very similar to the
rsk7203 board.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
If you take a look at 96820a35, you'll see the original timeout was
CONFIG_SYS_HZ. Which is 1000. After the mentioned change, non-bulk timeout
was changed to 100. This causes timeout failures on the dreamplug platform
when trying to initialize the usb microsd reader.
Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Built-in Ethernet adapters support setting the mac address by means of a
ethaddr environment variable for each interface (ethaddr, eth1addr, eth2addr).
This adds similar support to the USB network side, using the names
usbethaddr, usbeth1addr, etc. They are kept separate since we don't want
a USB device taking the MAC address of a built-in device or vice versa.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>
The SMSC95XX is a USB hub with a built-in Ethernet adapter. This adds support
for this, using the USB host network framework.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
On newer rev5 hardware the extension board EEPROM I2C address
has been changed to 0x54. Make this I2C address configurable
depending on CONFIG_DIGSY_REV5 so that extention board presence
detection works correctly on newer hardware.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The U-Boot Design Principles[1] clearly say:
Initialize devices only when they are needed within U-Boot, i.e. don't
initialize the Ethernet interface(s) unless U-Boot performs a download
over Ethernet; don't initialize any IDE or USB devices unless U-Boot
actually tries to load files from these, etc. (and don't forget to
shut down these devices after using them - otherwise nasty things may
happen when you try to boot your OS).
So, do not initialize and read the sensors on startup.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Holger Brunck <holger.brunck@keymile.com>
* 'master' of git://git.denx.de/u-boot-arm:
drivers/rtc: add Marvell Integrated RTC
Armada100: Add Board Support for Marvell GuruPlug-Display
Armada100: MFP macro naming correction
arm: auto gen asm-offsets.h for mb86r0x
spear: fix build errors for spear3xx/spear600 platforms
cosmetic: arm: lib/board.c: Coding Style cleanup
ARM: versatile: fix board support
SMDKV310: Enable device tree support
SMDKV310: MMC_SPL: Fix building when using "make O="
arm: a320: enable tagged list support
arm: a320: fix multiline comment style
ARMv7: u8500_href: Add missing header to fix compiler warning
Removed unused define, CONFIG_ARMV7.
avr32: add grasshopper (ICnova AP7000) board
AT91/SPI: fix atmel_dataflash_spi.c to allow building without warnings
MAKEALL: remove AT91 boards that are in boards.cfg
AT91: Makes AT91SAM9263-EK build correctly against u-boot-atmel/master
AT91: Makes AT91SAM9263 SoC build correctly against u-boot-atmel/master
AT91: Board fix for AT91SAM9261-EK
AT91: SoC fix at91sam9261_matrix.h
AT91: Makes AT91SAM9RL-EK build correctly against u-boot-atmel/master
AT91: Makes AT91SAM9RL SoC build correctly against u-boot-atmel/master
AT91: change common at91sam9261 files to compile with new scheme
AT91: fix mistake in at91sam9260_devices.c(spi1_hw_init)
a/a/c/arm920t/at91/reset.c: drop obsolete CONFIG_AT91RM9200_USART
README: fix arm920t/at91 path
net/eth.c: drop obsolete at91rm9200 support
README.at91-soc: remove AT91(RM9200) joining notice
a/a/c/arm920t/cpu.c: remove CONFIG_AT91_LEGACY warning
MAKEALL: remove obsolete at91rm9200 soc
ARM: remove obsolete at91rm9200
omap4: clock init support for omap4460
omap4: support TPS programming
omap: reuse omap3 gpio support in omap4
omap4: sdram init changes for omap4460
omap4: add omap4460 revision detection
mkimage: Add OMAP boot image support
omap: add MMC and FAT support to SPL
omap: add basic SPL support
armv7: start.S: fixes and enhancements for SPL
omap4: automatic sdram detection
omap4: calculate EMIF register values
omap4: add sdram init support
omap4: add clock support
omap4: add OMAP4430 revision check
omap4: cleanup pin mux data
omap4: utility function to identify the context of hw init
DA8xx: fix LPSC constants
DA8xx: switch an enum to defines for consistency
DA8xx: add MMC/SD controller addresses
DaVinci EMAC: declare function for all DA8xx CPUs
DA8xx: add generic GPIO driver
DaVinci: rename gpio_defs.h to gpio.h
omap3evm: eth: Include functions only when necessary
omap3evm: Update ethernet reset sequence for Rev.G board
omap3evm: eth: split function setup_net_chip
omap3: Include array definition only when it is used
omap730p2: fix build breaks
omap2420h4: fix build breaks
omap1610inn: fix build breaks
omap1510inn: fix build breaks
omap5912osk: fix build breaks
omap1610h2: fix build breaks
The SHARP LQ084S3LG01 is a TFT LCD used on the P1022DS (revision "C") board.
This device only supports 800x600 resolution, so if that resolution is selected,
assume that this is the device. The device is attached to the LVDS port
on the P1022DS board.
The existing 800x600 entry (for the PDM360NG board) is actually 800x480,
so we fix that. To support two different 800x resolutions, the Y-resolution
is now passed to fsl_diu_init() and both values are used to pick the proper
fb_videomode structure.
The data for the 800x600 video mode is originally from Jiang Yutang.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
This patch adds basic board support with DRAM and UART functionality
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Acked-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Versatile board is used as example to run u-boot under qemu.
The patch fixes relocation for all versatile boards and adds
a versatileqemu target to be used under qemu.
Patch tested only under qemu, not on real boards.
Tested with QEMU emulator version 0.14.50.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Alessandro Rubini <rubini-list@gnudd.com>
CC: Loïc Minier <loic.minier@linaro.org>
The grasshopper board is a neat avr32 evaluation kit produced by In-Circuit
GmbH.
See http://www.ic-board.de/product_info.php?info=p75_ICnova-AP7000-Base.html
for detailed information about this device.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Rework for AT91SAM9263-EK, makes it build again.
Based on the work for AT91SAM9260-EK.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <uboot@emk-elektronik.de>