DSPI has pin muxing with SDHC and other IPs, this patch check the
value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check
the "hwconfig" variable. If those pins are configured to DSPI and
"hwconfig" enable DSPI, set the BRDCFG5 of QIXIS CPLD to configure
the routing to on-board SPI memory. Otherwise will configure to SDHC.
DSPI is enabled in "hwconfig" by appending "dspi", eg.
setenv hwconfig "$hwconfig;dspi"
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DSPI has pin muxing with SDHC and other IPs, this patch check the
value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check
the "hwconfig" variable. If those pins are configured to DSPI and
"hwconfig" enable DSPI, set the BRDCFG5 of QIXIS FPGA to configure
the routing to on-board SPI memory. Otherwise will configure to SDHC.
DSPI is enabled in "hwconfig" by appending "dspi", eg.
setenv hwconfig "$hwconfig;dspi"
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As SCFG_ENDIANCR register is added to choose little-endian or big-endian
for audio IPs on Rev2.0 silion, little-endian mode is selected.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The agreed split of the top of memory is 256M for debug server and 256M
for MC. This patch implements the split.
In addition, the MC mem must be 512MB aligned, so the amount of memory
to hide must be 512MB to achieve that alignment.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch allows u-boot to expose the complete DDR region(s) to Linux
(after subtracting the memory hidden via MEM_TOP_HIDE mechanism).
This allows the u-boot to support the 48-bit VA support provided by
ARM64 Linux in flavors 3.18 and above, by passing the appropriate
'memory' DTS nodes.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Board rev C and earlier has duplicated SPD address on 2nd DDR
controller slots. It is fixed on rev D and later. SPD addresses
need to be updated accordingly.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
LS2085A supports 6 personalities i.e. LS2045AE, LS2045A, LS2080AE,
LS2080A, LS2085AE and LS2085A personlities.
Instead of hard-coding, board name should change as per selected
personality.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As per updated board document, no need to substract 1 from arch[BRD]
bit field. Default value + 'A' represents the board revision.
So update board version print logic to reflect the same.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SYSTEM ID EPPROM always store SYSTEM version info in big endian format.
SoC with ARM or PowerPC core should read/write version info from eeprom
in BIG endian format.
So use cpu-specific APIs to read SYSTEM version.
Signed-off-by: Jaiprakash Singh <b44839 at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
FPGA BRDCFG9[SFP_TX] should be clear in order to enable XFI ports.
Signed-off-by: Dai Haruki <Dai.Haruki at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes Protocol 0x49 enables 4 SGMII, PEX4, SATA1 and SATA2.
Add support of 0x49 SerDes protocol to enable 4SGMII on slot4 of
ls2085aqds platform.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add hwconfig setting for eSDHC since it shares some pins with other
IP block.
Signed-off-by: Yangbo Lu <yangbo.lu at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for board eth initialization and support for loading phy
firmware. PHY firmware needs to be loaded from board_eth_init() because
all the MACs are not initialized by ldpaa_eth driver.
Signed-off-by: pankaj chauhan <pankaj.chauhan at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ccsr_ddr structure is already defined in fsl_immap.h. Remove
this duplicated define. Move fixed timing into ls1021atwr.h.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
CONFIG_ARMV7_VIRT depends on CONFIG_ARMV7_NONSEC, thus doesn't need to
be taken into account additionally. CONFIG_ARMV7_PSCI is only set on
boards that support CONFIG_ARMV7_NONSEC, and it only works on those.
CC: Tang Yuantian <Yuantian.Tang@freescale.com>
CC: York Sun <yorksun@freescale.com>
CC: Steve Rae <srae@broadcom.com>
CC: Andre Przywara <andre.przywara@linaro.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
1. board/freescale/t4qds/t4_rcw.cfg
1.8GHz support is requested as default frequency, so update the rcw.
2. remove un-used configs
configs/T4160QDS_SPIFLASH_defconfig
configs/T4240QDS_SPIFLASH_defconfig
SPI boot is not available on T4QDS, so the configs should be removed.
3. board/freescale/t4qds/MAINTAINERS
Updated MAINTAINERS accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
[York Sun: revise subject]
Reviewed-by: York Sun <yorksun@freescale.com>
T2080RDB RevC uses new SODIMM 1867MT/s instead of previous 1600MT/s.
So update RCW to support new DDR frequency 1867MT/s by default.
Reserve the old 1600MT/s in comment for users in needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add adapter card type identification support by reading
FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function,
define CONFIG_FSL_ESDHC_ADAPTER_IDENT.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
[York Sun: resolve conflicts in README.fsl-esdhc]
Reviewed-by: York Sun <yorksun@freescale.com>
CS4315 PHY doesn't support phy-reset by software, it
needs to reset it by hardware via CPLD control.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Function dp_ddr_restore is to restore the first 128-byte space
of DDR. However those codes may be optimized out by compiler
since the destination address is at 0x0. In order to avoid
compiler optimization, we restore the space from high address,
which is not at 0x0, to low address.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Use fdt_setprop_string instead of fdt_setprop to fix string length.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1023RDB is a Freescale Reference Design Board that hosts the T1023 SoC.
T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- one 1G RGMII port on-board(RTL8211F PHY)
- one 1G SGMII port on-board(RTL8211F PHY)
- one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR: 128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash.
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC card and eMMC on-board
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339 on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging
As well updated T1024RDB to add T1023RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix defconfig files]
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for T4240RDB board. SPL
framework is used. PBL initializes the internal RAM and
copies SPL to it. Then SPL initializes DDR using SPD and
copies u-boot from SD card to DDR, finally SPL transfers
control to u-boot.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: Fix T4240RDB_SDCARD_defcofig]
Reviewed-by: York Sun <yorksun@freescale.com>
Enable NAND boot support using SPL framework. To boot from
NAND, either use DIP switches on board, or "qixis_reset nand"
command. Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
Use "qixis_reset nand" to reset the board to boot from NAND.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
IFC has two register pages.Till IFC version 1.4 each
register page is 4KB each.But IFC ver 2.0 register page
size is 64KB each.IFC regiters structure is break into
two viz FCM and RUNTIME.FCM(Flash control machine) registers
are defined in PAGE0 and controls IFC generic functionality.
RUNTIME registers are defined in PAGE1 and controls NAND and
GPCM funcinality.
FCM and RUNTIME structures defination is common for IFC
version 1.4 and 2.0.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Add support of ethernet:
- eth.c: mapping lane to slot for (0x2A, 0x07)
- ls2085a.c: To enable/disable dpmac and get link type
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Enable the SCSC (Slow Clock Source Controller) and select the external
32KHz oscillator. This improves the accuracy of the RTC.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
In order to avoid code duplication, move the DDR3 initialization to the
common place under imx-common. Currently ROW_DIFF and COL_DIFF can be
chosen from the board file. The JEDEC timings are specified using a
common ddr3_jedec_timings structure.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Add architecture-specific u-boot.lds and remove all board-specific
u-boot.lds.
All the .text customization that was board-specific have been
moved inside the related include/configs, inside a
LDS_BOARD_TEXT define.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
The LS2085ARDB is a evaluation platform that supports LS2085A
family SoCs. This patch add sbasic support for the platform.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The LS2085AQDS is an evaluatoin platform that supports the LS2085A
family SoCs. This patch add basic support of the platform.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Add support for reset_cpu() by asserting RESET_REQ_B.
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
The timer clock is system clock divided by 4, not fixed 12MHz.
This is common to the SoC, not board specific. Primary core is
fixed when u-boot still runs in board_f. Secondary cores are
fixed by reading a variable set by u-boot.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Mark Rutland <mark.rutland@arm.com>
mx6sabresd has four MT41K128M16JT-125 chips. Each memory has 16-bit bus
and 2GiB, so fix the width and density fields accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Move the compilation of file fsl_validate.c in MACRO CONFIG_CMD_ESBC_VALIDATE.
This file should be compiled only when the above MACRO is defined
This caused a break in compilation of iMX platforms when compiling for SECURE_BOOT
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Freescale's Layerscape Management Complex (MC) provide support various
objects like DPRC, DPNI, DPBP and DPIO.
Where:
DPRC: Place holdes for other MC objectes like DPNI, DPBP, DPIO
DPBP: Management of buffer pool
DPIO: Used for used to QBMan portal
DPNI: Represents standard network interface
These objects are used for DPAA ethernet drivers.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Debug Server driver is responsible for loading the Debug
server FW on the Service Processor (Cortex-A5 core) on LS2085A like
SoCs and then polling for the successful initialization of the same.
TOP MEM HIDE is adjusted to ensure the space required by Debug Server
FW is accounted for. MC uses the DDR area which is calculated as:
MC DDR region start = Top of DDR - area reserved by Debug Server FW
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch uses the common function name ft_pci_setup to replace
ft_pcie_setup, then removes unnecessary pcie_layerscape.h because
all the functions have been declared in common.h.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <yorksun@freescale.com>
