powerpc/t1023rdb: Add T1023 RDB board support

T1023RDB is a Freescale Reference Design Board that hosts the T1023 SoC.

T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
  - one 1G RGMII port on-board(RTL8211F PHY)
  - one 1G SGMII port on-board(RTL8211F PHY)
  - one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR:  128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash.
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC card and eMMC on-board
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339 on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging

As well updated T1024RDB to add T1023RDB.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix defconfig files]
Reviewed-by: York Sun <yorksun@freescale.com>
This commit is contained in:
Shengzhou Liu 2015-03-27 15:48:34 +08:00 committed by York Sun
parent 1d0b59a9b0
commit e8a7f1c32b
19 changed files with 382 additions and 44 deletions

View File

@ -8,3 +8,8 @@ F: configs/T1024RDB_NAND_defconfig
F: configs/T1024RDB_SDCARD_defconfig
F: configs/T1024RDB_SPIFLASH_defconfig
F: configs/T1024RDB_SECURE_BOOT_defconfig
F: configs/T1023RDB_defconfig
F: configs/T1023RDB_NAND_defconfig
F: configs/T1023RDB_SDCARD_defconfig
F: configs/T1023RDB_SPIFLASH_defconfig
F: configs/T1023RDB_SECURE_BOOT_defconfig

View File

@ -8,7 +8,7 @@ ifdef CONFIG_SPL_BUILD
obj-y += spl.o
else
obj-y += t102xrdb.o
obj-y += cpld.o
obj-$(CONFIG_T1024RDB) += cpld.o
obj-y += eth_t102xrdb.o
obj-$(CONFIG_PCI) += pci.o
endif

View File

@ -98,6 +98,30 @@ T1024RDB board Overview
- Four I2C ports
T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- SDRAM memory: 2GB Micron MT40A512M8HX unbuffered 32-bit DDR4 w/o ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- one 1G RGMII port on-board(RTL8211FS PHY)
- one 1G SGMII port on-board(RTL8211FS PHY)
- one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR: 128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash.
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC and eMMC card
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339U on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging
Memory map on T1024RDB
----------------------
Start Address End Address Description Size
@ -117,29 +141,39 @@ Start Address End Address Description Size
0x0_0000_0000 0x0_ffff_ffff DDR 4GB
128MB NOR Flash memory Map
--------------------------
128MB NOR Flash Memory Layout
-----------------------------
Start Address End Address Definition Max size
0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB
0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB
0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB
0xEFE00000 0xEFE3FFFF QE firmware (current bank) 256KB
0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB
0xED300000 0xEFDFFFFF rootfs (alt bank) 44MB
0xED000000 0xED2FFFFF Guest image #3 (alternate bank) 3MB
0xECD00000 0xECFFFFFF Guest image #2 (alternate bank) 3MB
0xECA00000 0xECCFFFFF Guest image #1 (alternate bank) 3MB
0xEC900000 0xEC9FFFFF HV config device tree(alt bank) 1MB
0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB
0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB
0xEC700000 0xEC7FFFFF HV.uImage (alternate bank) 1MB
0xEC020000 0xEC6FFFFF Linux.uImage (alt bank) ~7MB
0xEC000000 0xEC01FFFF RCW (alt bank) 128KB
0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB
0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB
0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB
0xEBE00000 0xEBE3FFFF QE firmware (alt bank) 256KB
0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB
0xE9300000 0xEBDFFFFF rootfs (current bank) 44MB
0xE9000000 0xE92FFFFF Guest image #3 (current bank) 3MB
0xE8D00000 0xE8FFFFFF Guest image #2 (current bank) 3MB
0xE8A00000 0xE8CFFFFF Guest image #1 (current bank) 3MB
0xE8900000 0xE89FFFFF HV config device tree(cur bank) 1MB
0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB
0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB
0xE8700000 0xE87FFFFF HV.uImage (current bank) 1MB
0xE8020000 0xE86FFFFF Linux.uImage (current bank) ~7MB
0xE8000000 0xE801FFFF RCW (current bank) 128KB
T1024 Clock frequency
---------------------
T1024/T1023 Clock frequency
---------------------------
BIN Core DDR Platform FMan
Bin1: 1400MHz 1600MT/s 400MHz 700MHz
Bin2: 1200MHz 1600MT/s 400MHz 600MHz
@ -155,16 +189,27 @@ Software configurations and board settings
b. program u-boot.bin image to NOR flash
=> tftp 1000000 u-boot.bin
=> pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
on T1024RDB:
set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
on T1023RDB:
set SW1[1:8] = '00010110', SW2[1] = '0', SW3[4] = '0' for NOR boot
Switching between default bank0 and alternate bank4 on NOR flash
To change boot source to vbank4:
via software: run command 'cpld reset altbank' in u-boot.
via DIP-switch: set SW3[5:7] = '100'
on T1024RDB:
via software: run command 'cpld reset altbank' in u-boot.
via DIP-switch: set SW3[5:7] = '100'
on T1023RDB:
via software: run command 'gpio vbank4' in u-boot.
via DIP-switch: set SW3[5:7] = '100'
To change boot source to vbank0:
via software: run command 'cpld reset' in u-boot.
via DIP-Switch: set SW3[5:7] = '000'
on T1024RDB:
via software: run command 'cpld reset' in u-boot.
via DIP-Switch: set SW3[5:7] = '000'
on T1023RDB:
via software: run command 'gpio vbank0' in u-boot.
via DIP-switch: set SW3[5:7] = '000'
2. NAND Boot:
a. build PBL image for NAND boot
@ -183,8 +228,11 @@ Software configurations and board settings
b. program u-boot-with-spl-pbl.bin to SPI flash
=> tftp 1000000 u-boot-with-spl-pbl.bin
=> sf probe 0
=> sf erase 0 f0000
=> sf erase 0 100000
=> sf write 1000000 0 $filesize
=> tftp 1000000 fsl_fman_ucode_t1024_xx.bin
=> sf erase 100000 100000
=> sf write 1000000 110000 20000
set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot
4. SD Boot:
@ -236,23 +284,34 @@ Start End Definition Size
0x200000 0x27FFFF QE Firmware 512KB(1 block)
NAND Flash memory Map on T1023RDB
----------------------------------------------------
Start End Definition Size
0x000000 0x0FFFFF u-boot 1MB
0x100000 0x15FFFF u-boot env 8KB
0x160000 0x17FFFF FMAN Ucode 128KB
SD Card memory Map on T1024RDB
----------------------------------------------------
Block #blocks Definition Size
0x008 2048 u-boot img 1MB
0x800 0016 u-boot env 8KB
0x820 0256 FMAN Ucode 128KB
0x920 0256 QE Firmware 128KB
0x920 0256 QE Firmware 128KB(only T1024RDB)
SPI Flash memory Map on T1024RDB
64MB SPI Flash memory Map on T102xRDB
----------------------------------------------------
Start End Definition Size
0x000000 0x0FFFFF u-boot img 1MB
0x100000 0x101FFF u-boot env 8KB
0x110000 0x12FFFF FMAN Ucode 128KB
0x130000 0x14FFFF QE Firmware 128KB
0x130000 0x14FFFF QE Firmware 128KB(only T1024RDB)
0x300000 0x3FFFFF device tree 128KB
0x400000 0x9FFFFF Linux kernel 6MB
0xa00000 0x3FFFFFF rootfs 54MB
For more details, please refer to T1024RDB Reference Manual and access
website www.freescale.com and Freescale QorIQ SDK Infocenter document.
For more details, please refer to T1024RDB Reference Manual
and Freescale QorIQ SDK Infocenter document.

View File

@ -135,8 +135,83 @@ found:
/* for DDR bus 32bit test on T1024 */
popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
#endif
#ifdef CONFIG_T1023RDB
popts->wrlvl_ctl_2 = 0x07070606;
popts->half_strength_driver_enable = 1;
#endif
}
#ifdef CONFIG_SYS_DDR_RAW_TIMING
/* 2GB discrete DDR4 MT40A512M8HX on T1023RDB */
dimm_params_t ddr_raw_timing = {
.n_ranks = 1,
.rank_density = 0x80000000,
.capacity = 0x80000000,
.primary_sdram_width = 32,
.ec_sdram_width = 8,
.registered_dimm = 0,
.mirrored_dimm = 0,
.n_row_addr = 15,
.n_col_addr = 10,
.bank_addr_bits = 2,
.bank_group_bits = 2,
.edc_config = 0,
.burst_lengths_bitmask = 0x0c,
.tckmin_x_ps = 938,
.tckmax_ps = 1500,
.caslat_x = 0x000DFA00,
.taa_ps = 13500,
.trcd_ps = 13500,
.trp_ps = 13500,
.tras_ps = 33000,
.trc_ps = 46500,
.trfc1_ps = 260000,
.trfc2_ps = 160000,
.trfc4_ps = 110000,
.tfaw_ps = 25000,
.trrds_ps = 3700,
.trrdl_ps = 5300,
.tccdl_ps = 5355,
.refresh_rate_ps = 7800000,
.dq_mapping[0] = 0x0,
.dq_mapping[1] = 0x0,
.dq_mapping[2] = 0x0,
.dq_mapping[3] = 0x0,
.dq_mapping[4] = 0x0,
.dq_mapping[5] = 0x0,
.dq_mapping[6] = 0x0,
.dq_mapping[7] = 0x0,
.dq_mapping[8] = 0x0,
.dq_mapping[9] = 0x0,
.dq_mapping[10] = 0x0,
.dq_mapping[11] = 0x0,
.dq_mapping[12] = 0x0,
.dq_mapping[13] = 0x0,
.dq_mapping[14] = 0x0,
.dq_mapping[15] = 0x0,
.dq_mapping[16] = 0x0,
.dq_mapping[17] = 0x0,
.dq_mapping_ors = 1,
};
int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
unsigned int controller_number,
unsigned int dimm_number)
{
const char dimm_model[] = "Fixed DDR4 on board";
if (((controller_number == 0) && (dimm_number == 0)) ||
((controller_number == 1) && (dimm_number == 0))) {
memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
}
return 0;
}
#endif
#if defined(CONFIG_DEEP_SLEEP)
void board_mem_sleep_setup(void)
{
@ -155,8 +230,9 @@ phys_size_t initdram(int board_type)
phys_size_t dram_size;
#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
#ifndef CONFIG_SYS_DDR_RAW_TIMING
puts("Initializing....using SPD\n");
#endif
dram_size = fsl_ddr_sdram();
dram_size = setup_ddr_tlbs(dram_size / 0x100000);
dram_size *= 0x100000;

View File

@ -1,6 +1,8 @@
/*
* Copyright 2014 Freescale Semiconductor, Inc.
*
* Shengzhou Liu <Shengzhou.Liu@freescale.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
@ -56,6 +58,7 @@ int board_eth_init(bd_t *bis)
fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR);
switch (srds_s1) {
#ifdef CONFIG_T1024RDB
case 0x95:
/* set the on-board RGMII2 PHY */
fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR);
@ -63,10 +66,17 @@ int board_eth_init(bd_t *bis)
/* set 10G XFI with Aquantia AQR105 PHY */
fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
break;
#endif
case 0x6a:
case 0x6b:
case 0x77:
case 0x135:
/* set the on-board 2.5G SGMII AQR105 PHY */
fm_info_set_phy_address(FM1_DTSEC3, SGMII_PHY1_ADDR);
fm_info_set_phy_address(FM1_DTSEC3, SGMII_AQR_PHY_ADDR);
#ifdef CONFIG_T1023RDB
/* set the on-board 1G SGMII RTL8211F PHY */
fm_info_set_phy_address(FM1_DTSEC1, SGMII_RTK_PHY_ADDR);
#endif
break;
default:
printf("SerDes protocol 0x%x is not supported on T102xRDB\n",
@ -81,6 +91,14 @@ int board_eth_init(bd_t *bis)
dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
fm_info_set_mdio(i, dev);
break;
case PHY_INTERFACE_MODE_SGMII:
#if defined(CONFIG_T1023RDB)
dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
#elif defined(CONFIG_T1024RDB)
dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
#endif
fm_info_set_mdio(i, dev);
break;
case PHY_INTERFACE_MODE_SGMII_2500:
dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
fm_info_set_mdio(i, dev);
@ -110,13 +128,16 @@ int board_eth_init(bd_t *bis)
void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
enum fm_port port, int offset)
{
if ((fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) &&
(port == FM1_DTSEC3)) {
#if defined(CONFIG_T1024RDB)
if (((fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) ||
(fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII)) &&
(port == FM1_DTSEC3)) {
fdt_set_phy_handle(fdt, compat, addr, "sg_2500_aqr105_phy4");
fdt_setprop(fdt, offset, "phy-connection-type",
"sgmii-2500", 10);
fdt_status_disabled_by_alias(fdt, "xg_aqr105_phy3");
}
#endif
}
void fdt_fixup_board_enet(void *fdt)

View File

@ -0,0 +1,8 @@
#PBL preamble and RCW header for T1023RDB
aa55aa55 010e0100
#SerDes Protocol: 0x77
#Core/DDR: 1400Mhz/1600MT/s with single source clock
0810000e 00000000 00000000 00000000
3b800003 00000012 e8104000 21000000
00000000 00000000 00000000 00020800
00000130 04020200 00000000 00000006

View File

@ -18,11 +18,25 @@
#include <asm/fsl_liodn.h>
#include <fm_eth.h>
#include "t102xrdb.h"
#ifdef CONFIG_T1024RDB
#include "cpld.h"
#endif
#include "../common/sleep.h"
DECLARE_GLOBAL_DATA_PTR;
#ifdef CONFIG_T1023RDB
enum {
GPIO1_SD_SEL = 0x00020000, /* GPIO1_14, 0: EMMC, 1:SD/MMC */
GPIO1_EMMC_SEL,
GPIO1_VBANK0,
GPIO1_VBANK4 = 0x00008000, /* GPIO1_16/20/22, 100:vBank4 */
GPIO1_VBANK_MASK = 0x00008a00,
GPIO1_DIR_OUTPUT = 0x00028a00,
GPIO1_GET_VAL,
};
#endif
int checkboard(void)
{
struct cpu_type *cpu = gd->arch.cpu;
@ -34,14 +48,17 @@ int checkboard(void)
srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
printf("Board: %sRDB, ", cpu->name);
printf("Board rev: 0x%02x CPLD ver: 0x%02x, boot from ",
#ifdef CONFIG_T1024RDB
printf("Board rev: 0x%02x CPLD ver: 0x%02x, ",
CPLD_READ(hw_ver), CPLD_READ(sw_ver));
#endif
printf("boot from ");
#ifdef CONFIG_SDCARD
puts("SD/MMC\n");
#elif CONFIG_SPIFLASH
puts("SPI\n");
#else
#elif defined(CONFIG_T1024RDB)
u8 reg;
reg = CPLD_READ(flash_csr);
@ -52,17 +69,25 @@ int checkboard(void)
reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
printf("NOR vBank%d\n", reg);
}
#elif defined(CONFIG_T1023RDB)
#ifdef CONFIG_NAND
puts("NAND\n");
#else
printf("NOR vBank%d\n", (t1023rdb_gpio_ctrl(GPIO1_GET_VAL) &
GPIO1_VBANK4) >> 15 ? 4 : 0);
#endif
#endif
puts("SERDES Reference Clocks:\n");
if (srds_s1 == 0x95)
printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[2], freq[0]);
else
printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[0], freq[0]);
printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[0], freq[1]);
return 0;
}
#ifdef CONFIG_T1024RDB
static void board_mux_lane(void)
{
ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
@ -82,6 +107,7 @@ static void board_mux_lane(void)
}
CPLD_WRITE(boot_override, CPLD_OVERRIDE_MUX_EN);
}
#endif
int board_early_init_f(void)
{
@ -124,7 +150,9 @@ int board_early_init_r(void)
#ifdef CONFIG_SYS_DPAA_QBMAN
setup_portals();
#endif
#ifdef CONFIG_T1024RDB
board_mux_lane();
#endif
return 0;
}
@ -170,3 +198,62 @@ int ft_board_setup(void *blob, bd_t *bd)
return 0;
}
#ifdef CONFIG_T1023RDB
static u32 t1023rdb_gpio_ctrl(u32 ctrl_type)
{
ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
u32 gpioval;
setbits_be32(&pgpio->gpdir, GPIO1_DIR_OUTPUT);
gpioval = in_be32(&pgpio->gpdat);
switch (ctrl_type) {
case GPIO1_SD_SEL:
gpioval |= GPIO1_SD_SEL;
break;
case GPIO1_EMMC_SEL:
gpioval &= ~GPIO1_SD_SEL;
break;
case GPIO1_VBANK0:
gpioval &= ~GPIO1_VBANK_MASK;
break;
case GPIO1_VBANK4:
gpioval &= ~GPIO1_VBANK_MASK;
gpioval |= GPIO1_VBANK4;
break;
case GPIO1_GET_VAL:
return gpioval;
default:
break;
}
out_be32(&pgpio->gpdat, gpioval);
return 0;
}
static int gpio_cmd(cmd_tbl_t *cmdtp, int flag, int argc,
char * const argv[])
{
if (argc < 2)
return CMD_RET_USAGE;
if (!strcmp(argv[1], "vbank0"))
t1023rdb_gpio_ctrl(GPIO1_VBANK0);
else if (!strcmp(argv[1], "vbank4"))
t1023rdb_gpio_ctrl(GPIO1_VBANK4);
else if (!strcmp(argv[1], "sd"))
t1023rdb_gpio_ctrl(GPIO1_SD_SEL);
else if (!strcmp(argv[1], "EMMC"))
t1023rdb_gpio_ctrl(GPIO1_EMMC_SEL);
else
return CMD_RET_USAGE;
return 0;
}
U_BOOT_CMD(
gpio, 2, 0, gpio_cmd,
"for vbank0/vbank4/SD/eMMC switch control in runtime",
"command (e.g. gpio vbank4)"
);
#endif

View File

@ -9,5 +9,7 @@
void fdt_fixup_board_enet(void *blob);
void pci_of_setup(void *blob, bd_t *bd);
#ifdef CONFIG_T1023RDB
static u32 t1023rdb_gpio_ctrl(u32 ctrl_type);
#endif
#endif

View File

@ -0,0 +1,5 @@
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1023,T1023RDB,RAMBOOT_PBL,SPL_FSL_PBL,NAND"
CONFIG_PPC=y
CONFIG_MPC85xx=y
CONFIG_TARGET_T102XRDB=y

View File

@ -0,0 +1,5 @@
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1023,T1023RDB,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD"
CONFIG_PPC=y
CONFIG_MPC85xx=y
CONFIG_TARGET_T102XRDB=y

View File

@ -0,0 +1,4 @@
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1023,T1023RDB,SECURE_BOOT"
CONFIG_PPC=y
CONFIG_MPC85xx=y
CONFIG_TARGET_T102XRDB=y

View File

@ -0,0 +1,5 @@
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1023,T1023RDB,RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH"
CONFIG_PPC=y
CONFIG_MPC85xx=y
CONFIG_TARGET_T102XRDB=y

View File

@ -0,0 +1,4 @@
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1023,T1023RDB"
CONFIG_PPC=y
CONFIG_MPC85xx=y
CONFIG_TARGET_T102XRDB=y

View File

@ -1,5 +1,5 @@
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,RAMBOOT_PBL,SPL_FSL_PBL,NAND"
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,T1024RDB,RAMBOOT_PBL,SPL_FSL_PBL,NAND"
CONFIG_PPC=y
CONFIG_MPC85xx=y
CONFIG_TARGET_T102XRDB=y

View File

@ -1,5 +1,5 @@
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD"
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,T1024RDB,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD"
CONFIG_PPC=y
CONFIG_MPC85xx=y
CONFIG_TARGET_T102XRDB=y

View File

@ -1,4 +1,4 @@
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,SECURE_BOOT"
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,T1024RDB,SECURE_BOOT"
CONFIG_PPC=y
CONFIG_MPC85xx=y
CONFIG_TARGET_T102XRDB=y

View File

@ -1,5 +1,5 @@
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH"
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,T1024RDB,RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH"
CONFIG_PPC=y
CONFIG_MPC85xx=y
CONFIG_TARGET_T102XRDB=y

View File

@ -1,4 +1,4 @@
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024"
CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,T1024RDB"
CONFIG_PPC=y
CONFIG_MPC85xx=y
CONFIG_TARGET_T102XRDB=y

View File

@ -11,6 +11,12 @@
#ifndef __T1024RDB_H
#define __T1024RDB_H
#if defined(CONFIG_T1023RDB)
#ifdef CONFIG_SPL
#define CONFIG_SYS_NO_FLASH
#endif
#endif
/* High Level Configuration Options */
#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_DISPLAY_BOARDINFO
@ -35,7 +41,9 @@
#define CONFIG_ENV_OVERWRITE
/* support deep sleep */
#ifdef CONFIG_PPC_T1024
#define CONFIG_DEEP_SLEEP
#endif
#if defined(CONFIG_DEEP_SLEEP)
#define CONFIG_SILENT_CONSOLE
#define CONFIG_BOARD_EARLY_INIT_F
@ -43,7 +51,11 @@
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xrdb/t1024_pbi.cfg
#if defined(CONFIG_T1024RDB)
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_rcw.cfg
#elif defined(CONFIG_T1023RDB)
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1023_rcw.cfg
#endif
#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
#define CONFIG_SPL_ENV_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
@ -177,7 +189,11 @@
#define CONFIG_ENV_SPI_MODE 0
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
#if defined(CONFIG_T1024RDB)
#define CONFIG_ENV_SECT_SIZE 0x10000
#elif defined(CONFIG_T1023RDB)
#define CONFIG_ENV_SECT_SIZE 0x40000
#endif
#elif defined(CONFIG_SDCARD)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_MMC
@ -188,7 +204,11 @@
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_SIZE 0x2000
#if defined(CONFIG_T1024RDB)
#define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_T1023RDB)
#define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE)
#endif
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
#define CONFIG_ENV_IS_IN_REMOTE
#define CONFIG_ENV_ADDR 0xffe20000
@ -209,7 +229,7 @@ unsigned long get_board_ddr_clk(void);
#endif
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_DDR_CLK_FREQ 66660000
#define CONFIG_DDR_CLK_FREQ 100000000
/*
* These can be toggled for performance analysis, otherwise use default.
@ -224,6 +244,7 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#endif
#define CONFIG_CMD_MEMTEST
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_ALT_MEMTEST
@ -265,13 +286,18 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_FSL_DDR_INTERACTIVE
#if defined(CONFIG_T1024RDB)
#define CONFIG_DDR_SPD
#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x51
#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
#elif defined(CONFIG_T1023RDB)
#define CONFIG_SYS_FSL_DDR4
#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_SYS_SDRAM_SIZE 2048
#endif
/*
* IFC Definitions
@ -291,7 +317,12 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
/* NOR Flash Timing Params */
#if defined(CONFIG_T1024RDB)
#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
#elif defined(CONFIG_T1023RDB)
#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
CSOR_NAND_TRHZ_80 | CSOR_NOR_ADM_SHFT_MODE_EN)
#endif
#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
FTIM0_NOR_TEADC(0x5) | \
FTIM0_NOR_TEAHC(0x5))
@ -315,6 +346,7 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
#ifdef CONFIG_T1024RDB
/* CPLD on IFC */
#define CONFIG_SYS_CPLD_BASE 0xffdf0000
#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
@ -336,6 +368,7 @@ unsigned long get_board_ddr_clk(void);
FTIM2_GPCM_TCH(0x8) | \
FTIM2_GPCM_TWP(0x1f))
#define CONFIG_SYS_CS2_FTIM3 0x0
#endif
/* NAND Flash on IFC */
#define CONFIG_NAND_FSL_IFC
@ -352,6 +385,7 @@ unsigned long get_board_ddr_clk(void);
| CSPR_V)
#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
#if defined(CONFIG_T1024RDB)
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
@ -359,9 +393,17 @@ unsigned long get_board_ddr_clk(void);
| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
#elif defined(CONFIG_T1023RDB)
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_RAL_3 /* RAL 3Bytes */ \
| CSOR_NAND_RAL_3 /* RAL 3Bytes */ \
| CSOR_NAND_PGS_2K /* Page Size = 2K */ \
| CSOR_NAND_SPRZ_128 /* Spare size = 128 */ \
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#endif
#define CONFIG_SYS_NAND_ONFI_DETECTION
/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
FTIM0_NAND_TWP(0x18) | \
@ -381,8 +423,6 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
#if defined(CONFIG_NAND)
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
@ -536,7 +576,11 @@ unsigned long get_board_ddr_clk(void);
*/
#define CONFIG_FSL_ESPI
#define CONFIG_SPI_FLASH
#if defined(CONFIG_T1024RDB)
#define CONFIG_SPI_FLASH_STMICRO
#elif defined(CONFIG_T1023RDB)
#define CONFIG_SPI_FLASH_SPANSION
#endif
#define CONFIG_CMD_SF
#define CONFIG_SPI_FLASH_BAR
#define CONFIG_SF_DEFAULT_SPEED 10000000
@ -736,8 +780,13 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_QE_FW_ADDR (512 * 0x920)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
#if defined(CONFIG_T1024RDB)
#define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
#define CONFIG_SYS_QE_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_T1023RDB)
#define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE)
#define CONFIG_SYS_QE_FW_ADDR (12 * CONFIG_SYS_NAND_BLOCK_SIZE)
#endif
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
/*
* Slave has no ucode locally, it can fetch this from remote. When implementing
@ -762,10 +811,16 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_PHYLIB_10G
#define CONFIG_PHY_REALTEK
#define CONFIG_PHY_AQUANTIA
#if defined(CONFIG_T1024RDB)
#define RGMII_PHY1_ADDR 0x2
#define RGMII_PHY2_ADDR 0x6
#define SGMII_PHY1_ADDR 0x2
#define SGMII_AQR_PHY_ADDR 0x2
#define FM1_10GEC1_PHY_ADDR 0x1
#elif defined(CONFIG_T1023RDB)
#define RGMII_PHY1_ADDR 0x1
#define SGMII_RTK_PHY_ADDR 0x3
#define SGMII_AQR_PHY_ADDR 0x2
#endif
#endif
#ifdef CONFIG_FMAN_ENET
@ -855,21 +910,23 @@ unsigned long get_board_ddr_clk(void);
*/
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_LOADADDR 1000000 /* default location for tftp, bootm */
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200
#define __USB_PHY_TYPE utmi
#ifdef CONFIG_PPC_T1024
#define CONFIG_BOARDNAME "t1024rdb"
#define CONFIG_BOARDNAME t1024rdb
#define BANK_INTLV cs0_cs1
#else
#define CONFIG_BOARDNAME "t1023rdb"
#define CONFIG_BOARDNAME t1023rdb
#define BANK_INTLV null
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
"bank_intlv=cs0_cs1\0" \
"bank_intlv=" __stringify(BANK_INTLV) "\0" \
"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
"ramdiskfile=" __stringify(CONFIG_BOARDNAME) "/ramdisk.uboot\0" \
"fdtfile=" __stringify(CONFIG_BOARDNAME) "/" \