Per datasheets of n25q256* and n25q512* not all variants of n25q256* and
n25q512* support 4 Byte stateless addressing opcodes. Therefore drop
SPI_NOR_4B_OPCODES flag from these entries
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Disable and free clock when remove driver.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
U-Boot uses CONFIG_SPI_FLASH_USE_4K_SECTORS to enable 4K small sector
support. Use that instead of MTD_SPI_NOR_USE_4K_SECTORS.
Reported-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Use dev_err() when reporting reason for erase/write failures so that
users can be made aware of the reason for failure.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
As SPI_FLASH_MTD is used in SPL and U-Boot proper, we enable both,
now that a separate option for SPL was introduced.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
[jagan: drop unrelated change]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To allow SPI_FLASH_MTD being enabled separately in SPL we add a new
option. The only user currently is the stm32mp15_basic board.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
SoPine has winbond SPI-FLASH, so enable the same in defconfig
and add aliases for spi0 in -u-boot.dtsi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
SPI is available in Allwinner A64 SoC, so enable it
globally in Kconfig.
- CONFIG_SPI
- CONFIG_DM_SPI
- CONFIG_DM_SPI_FLASH
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
SPI_SUNXI driver is fully dm-aware and the Allwinner
architecture kconfig would have logic to enable the
DM_SPI. So, select default spi sunxi driver for
sunxi architecture.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
DM_SPI_FLASH should require spi flash interface code for dm
version, so imply SPI_FLASH core by default if any board
enabled DM_SPI_FLASH.
This overcome the explicit enablement of CONFIG_SPI_FLASH on
respective boards when DM_SPI_FLASH being used.
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
If DM_SPI_FLASH enabled that means it is using sf command
for flash interface to access.
SPI_FLASH can be used via sf command and board/driver
functions to call spi flash ops, so mark it default only
for DM_SPI_FLASH.
This would prevent explicit adding of CONFIG_CMD_SF when
DM_SPI_FLASH being enabled.
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
We need distinguish the following two situations in various SPI APIs:
- given chip select num is invalid
- given chip select num is valid, but no device is attached
Currently -ENODEV is returned for both cases.
For the first case, it's more reasonable to return -EINVAL instead of
-ENODEV for invalid chip select numbers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If an SPI controller driver does not implement ops->cs_info, that
probably means any chip select number could be valid, hence let's
return 0 for spi_cs_info().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add is25wp256, chip to spi-nor id table.
Tested on SiFive FU540 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
1) CONFIG_SPI_FLASH is not just a legacy code, but it has common
core code which handle both dm and non-dm spi flash code. So
fix the info text to make it clear globally.
2) Since it's flash core it shouldn't depends on legacy SPI,
so remove the 'depends on SPI'
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The ULP has two USB controllers. These two controllers have similar NC
registers layout as i.MX7D. But OTG0 uses UTMI PHY simliar as i.MX6, not
the integrated PHY on i.MX7D. The OTG1 needs off-chip HSIC PHY or ULPI PHY
to work.
This patch only supports OTG0 with UTMI PHY.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This fixes the issues with calculation of controller indexes in
ehci_usb_bind() for iMX7, as USB controllers on iMX7 SoCs aren't
placed next to each other, and their addresses incremented by 0x10000.
Example of USB nodes for iMX7S/D:
usbotg1: usb@30b10000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b10000 0x200>;
^^^^^^^^^^
....
usbotg2: usb@30b20000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b20000 0x200>;
^^^^^^^^^^
....
usbh: usb@30b30000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b30000 0x200>;
^^^^^^^^^^
....
Which was leading to usb enumeration issues:
Colibri iMX7 # usb start
starting USB...
Bus usb@30b10000: USB EHCI 1.00
Bus usb@30b20000: probe failed, error -22
scanning bus usb@30b10000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Fixes: 501547cec1("usb: ehci-mx6: Fix bus enumeration for DM case")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
All platforms which are using MANUAL_RELOC are jumping back to origin
location when repeatable command is called. The reason is that cmd_rep link
is not updated properly. Issue can be reproduced by rewriting origin
U-Boot location through (for example) file download by tftp command.
Fixes: 80a48dd47e ("common: command: Rework the 'cmd is repeatable' logic")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Record two bootstages and add "Starting kernel" message to have standard
handoff message between U-Boot and OS.
Also use debug() instead of #ifdef DEBUG to clean the code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no need to show FDT message in regular flow that's why switch it
to debug level.
Fixes: 0905046050 ("microblaze: Switch to generic bootm implementation")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for System Controller available on e-a2197-00 base board.
System is very similar to p-a2197-00 board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_early_init_f added by commit e6cc3b25d7
("arm: zynq: Wire watchdog internals") is no longer needed that's why
remove it also with Kconfig enabling.
Fixes: ccd063e981 ("watchdog: Move watchdog_dev to data section (BSS may not be cleared)")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch removes 4K sector size support for Zynq mini qspi configuration
in favour of fast erase speed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch removes 4K sector size support for ZynqMP mini qspi
configuration in favour of fast erase speed.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are use cases where lpd watchdog can be configured for APU use. By
design this IP should be listed in zynqmp.dtsi to make sure that node is
properly enabled by DTG.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add dt clock header which can be included by dtses. And also use zynqmp-clk
compatible string.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch updates the nand device tree node properties as per
updated driver.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds configuration for single nand flash mini u-boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds manual relocation for Modular Exponentiation if
CONFIG_NEEDS_MANUAL_RELOC is enabled.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds manual relocation for struct hash_algo if
CONFIG_NEEDS_MANUAL_RELOC is enabled.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
