Fix memory reservations: do not use random bytes from the stack.
-----BEGIN PGP SIGNATURE-----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=j2MV
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc5-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc5 (2)
Fix memory reservations: do not use random bytes from the stack.
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far
unsupported, reinstate the old cd-gpios behavior until this handling
is fully implemented. This avoid potential issue for SDCard boot:
the card detect fails with floating gpio.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far
unsupported, reinstate the old cd-gpios behavior until this handling
is fully implemented. This permits the DHSOM to boot from SD again,
without this patch the card detect fails.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
fdtdec_get_addr_size reads the uses a fixed value for address & size
cell properties which may not be correct always.
Use the auto variant of the function which automatically reads
#address-cells & #size-cells from parent and uses to read the "reg"
property.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
On 32 bit systems fdt_addr_t may be 4 bytes long but size is defined as
u64. Avoid filling the upper 4 bytes of the sizep parameter of
fdtdec_get_addr_size_auto_parent() with random bytes from the stack by
defining a separate variable fdt_size.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This allows Nano to use the key M.2 on the CVB to connect and use a M.2
NVMe SSD stick. Works on my Nano B00, WD SN750 NVMe SSD shows up
w/'nvme' commands. Will add booting from NVMe via distro cmds in a future
patch.
Signed-off-by: Tom Warren <twarren@nvidia.com>
and cm_fx6 boards
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXuvX2Q4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXKQ9AJ4tL6uvQ0owuKlt5lkf3us6Dp7xwACfSJQrpmvj
fv4v4CCCv44oBkqwHtc=
=k6d2
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v2020.07-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix stdout in default environment for apalis_imx6, colibri_imx6
and cm_fx6 boards
The PSCI nodes are currently not populated for the Tegra210 and Tegra186
devices. This prevents the PSCI driver from being able to identify the
PSCI method used by these devices and causes the probe of the PSCI
driver to fail.
Since commit 81ea00838c ("efi_loader: PSCI reset and shutdown") was
added, which moves the PSCI EFI system reset handler into the PSCI
driver, this has prevented the EFI system reset from working for
Tegra210 and Tegra186. Therefore, populating these nodes is necessary
to fix the EFI system reset for Tegra210 and Tegra186.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
When CONFIG_OF_LIVE is enabled, dev_of_offset() cannot be used and
if used returns an invalid offset. This causes the call to
fdt_stringlist_get() in the psci_probe() to fail to read the 'method'
property from the PSCI node for the device and hence prevents PSCI
from working. Fix this by using the ofnode_read_string() API instead
of the fdt_stringlist_get() because this will handle reading the
property both when CONFIG_OF_LIVE is enabled or disabled.
Due to the above problem and since commit 81ea00838c ("efi_loader:
PSCI reset and shutdown") was added, the EFI system reset has been
broken for Tegra210 and Tegra196 platforms. This also fixes the EFI
system reset for these Tegra platforms.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
The ethernet PHY on all known Gen3 boards takes a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Add the recently added reStructuredText board documentation in the
appropriate MAINTAINERS files.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move the natural text Amlogic board README files to doc/board/amlogic
into reStructuredText and :
- add reStructuredText markup for bash code
- fix secondary titles markup
- move board support into global support matrix
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add OP-TEE firmware node in stm32mp15 U-Boot DTSI. This node is
needed since commit [1] that changed U-Boot/stm32mp15 to detect
OP-TEE availability by probing the resource instead of relying on
U-Boot configuration. The software sequence implemented by [1] is
fine but U-Boot DTS/DTSI files were not updated accordingly since,
hence OP-TEE presence is never detected by U-Boot, preventing Linux
kernel from using OP-TEE resources.
For consistency and to synchronize stm32mp15 DTSI files (excluding
U-Boot specific DTSI files) with the Linux kernel ones, this change
also moves the OP-TEE reserved memory nodes from board generic DTSI
files to U-Boot specific board DTSI files.
Link: [1] commit 43df0a159d ("stm32mp1: dynamically detect op-tee presence")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Fix the sequence in stm32mp1 fdt.c that disables OP-TEE resources
defined in FDT when U-boot detects OP-TEE firmware is not present.
Before this change, helper function stm32_fdt_disable_optee()
set property status to "disabled" for the OP-TEE reserved memory
nodes but this has no impact since Linux kernel does not consider
the status property for reserved-memory subnodes. This change
make U-Boot to attempt to delete the node instead.
Fixes: 4a1b975dac ("board: stm32mp1: reserve memory for OP-TEE in device tree")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use correct printf code in efi_image_parse().
Add random number generation to HTML documentation.
-----BEGIN PGP SIGNATURE-----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=yON/
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc5
Use correct printf code in efi_image_parse().
Add random number generation to HTML documentation.
The fix in commit b7adcdd073 has the side-effect that the regulator
will be disabled when requesting the relevant gpio in
regulator_common_ofdata_to_platdata() and enabled in
regulator_pre_probe() when the regulator was already enabled.
This leads to a short interruption in the 3.3V power to the PCIe
slot on the firefly-rk3399 which makes an ADATA SX8000NP NVMe SSD
unhappy.
Fix this by setting the GPIOD_IS_OUT_ACTIVE flag again when the
'regulator-boot-on' property is set, but check for this property
explicitly instead of relying on the "boot_on" member of
the uclass platdata.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Update the comment for SYS_RELOC_GD_ENV_ADDR as gd->env_addr is updated
in board_r.c::initr_reloc_global_data() under the compilation flags
CONFIG_SYS_RELOC_GD_ENV_ADDR
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Several configutation options require additional memory before relocation:
* CONSOLE_RECORD
* LOG
* RSA
The current default of 0x400 is too small to encompass them all. Increase
the value of SYS_MALLOC_F_LEN to 0x2000 for ARCH_QEMU.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This reverts commit 0486497e2b.
The strtoul has well-defined semantics. It is defined by the C standard and
POSIX. To quote the relevant section of the man pages,
> If base is zero or 16, the string may then include a "0x" prefix, and the
> number will be read in base 16; otherwise, a zero base is taken as 10
> (decimal) unless the next character is '0', in which case it is taken as
> 8 (octal).
Keeping these semantics is important for several reasons. First, it is very
surprising for standard library functions to behave differently than usual.
Every other implementation of strtoul has different semantics than the
implementation in U-Boot at the moment. Second, it can result in very
surprising results from small changes. For example, changing the string
"1f" to "20" causes the parsed value to *decrease*. Forcing use of the "0x"
prefix to specify hexidecimal numbers is a feature, not a bug. Lastly, this
is slightly less performant, since the entire number is parsed twice.
This fixes the str_simple_strtoul test failing with
test/str_ut.c:29, run_strtoul(): expect_val == val: Expected 0x44b (1099), got 0x1099ab (1087915)
test/str_ut.c:46, str_simple_strtoul(): 0 == run_strtoul(uts, str2, 0, 1099, 4): Expected 0x0 (0), got 0x1 (1)
Signed-off-by: Sean Anderson <seanga2@gmail.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Shiril Tichkule <shirilt@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
s/booot/boot/g
The first ase is booot instead of boot and second u-booot instead of
u-boot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fix the loop that parses FDT for a reserved memory node named "optee".
Before this change, if at least one subnode was found in the
reserved-memory node, the function endlessly looped since instruction
continue returned back in the loop without updating variable subnode.
This change fixes the issue by using a for loop.
Fixes: 6ccb05eae0 ("image: fdt: copy possible optee nodes to a loaded devicetree")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Unsupported voltage on voltage switch is not an error, do not
print error message in such a case. This happens e.g. if the
eMMC is already in 1V8 mode or when testing 1V2 mode operation
on systems which only do 3V3/1V8 switching.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The 3V3/1V8 switching could never have worked on any of the iMXes
ever since 51313b49f2 ("mmc: fsl_esdhc: support SDR104 and HS200"),
because that commit uses priv->vqmmc_dev when switching voltages on
mode switch, while local vqmmc_dev in probe to store the regulator
pointer. Those are two different variables with the same name. So
the priv->vqmmc_dev was always NULL and thus voltage switch between
modes never really suceeded.
Fix this by assigning priv->vqmmc_dev with value of the vqmmc_dev
in probe.
Fixes: 51313b49f2 ("mmc: fsl_esdhc: support SDR104 and HS200")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Change DT compatibility name to match change in driver's name.
Remove unused io_ds and fifo_mode fields from DT.
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Tom Rini <trini@konsulko.com>
- Rename DT compatible name
- Remove uneccessary if-statement to support 8-bit buswidth
- Remove redundant error msg
- Use symbolic constants in switch statement
Signed-off-by: Arthur Li <arthur.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Tom Rini <trini@konsulko.com>
When eSDHC operates at 3.3v, damage can accumulate in an internal
level shifter at a higher than expected rate. The faster the interface
runs, the more damage accumulates. This issue now is found on LX2160A
eSDHC1 for only SD card.
The hardware workaround is recommended to use an on-board level shifter
that is 1.8v on SoC side and 3.3v on SD card side.
For boards without hardware workaround, this option could be enabled,
ensuring 1.8v IO voltage and disabling eSDHC if no card.
This option assumes no hotplug, and u-boot has to make all the way to
to linux to use 1.8v UHS-I speed mode if has card.
If you do not want the workaround for better user experience, of course
you can choose to not select it running eSDHC in unsafe mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
For size_t we have to use %zu for printing not %lu.
Fixes: 4540dabdca ("efi_loader: image_loader: support image
authentication")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Commit e71b6f6622 ("i2c: designware_i2c: Rewrite timing calculation")
change the hcnt and lcnt timing calculation. New timing calculation is
based on calculation from Designware i2c databook.
After this new timing calculation, hcnt will have negative value
with i2c-scl-falling-time-ns 5000 that set in socfpga_cyclone5_socdk.dts.
This patch overwrite i2c-scl-falling-time-ns to 300ns (default SCL fall
time used in Designware i2c driver) for Uboot.
Before the fix:
=> i2c dev 0
Setting bus to 0
Failure changing bus number (-22)
After the fix:
=> i2c dev 0
Setting bus to 0
=> i2c probe
Valid chip addresses: 17 51 55 5B 5C 5E 66 68 70
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Update the firmware to improve compatibility for none-intel USB
host controller. The more information is as following.
The device has auto-installed driver feature - via switch CD-ROM/NIC
mode. But in some corner cases, it would switch to CD-ROM unexpected.
This issue results in Lan Function Disabled.
While USB PHY transits to P3 from P0 due to the absent of transmitter
control, it would issues undefined signal to its link partner.
Some Down Stream Port misidentify the undefined signal as wakeup
signal. So the link state will not keep in suspend even the system
is idle.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Enable DM_SPI for am355x sl50 board.
Build is fine, but not tested.
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Enable DM_SPI for igep00x0 board.
Build is fine, but not tested.
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Now all boards which are using davinci SPI driver
have moved to SPL_DM so drop the unneeded non-dm code.
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
