a64-olinuxino has 8GiB eMMC, enable it.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The clock selection is done now from the am335x-fb code, so there is no
more need doing this in the board code.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Actual am335x-fb implementation takes now a real clock frequency instead
a divider. So this component doesn't need to know anymore some base
frequency of the LCDC, we simply provide the pixel-clock frequency.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The LCDC IP-core an be feed from several clock sources, one of those is
a dedicated DPLL for generating a dividable base-clock for this IP-core.
The TRM specifies the maximum input frequency for the LCCD with 200 MHz,
so we must not exceed this value with the PLL frequency (which can lock
much higher).
This patch tries every combination of multipliers and divisors of the
PLL and the IP-core itself for getting as near as possible the the
requested panel->pxl_clk.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Using changes in this patch we were able to reduce approx 8k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1088a/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1088a/ls1088a.c to keep
board_early_init_f funcations in case of SPL build.
3. Changes in ls1088a_common.h & ls1088ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Compile-off mp.c and libfdt.c in case of SPL build. SPL size reduces
by approx 2k.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove duplicate macro CONFIG_FSL_PCIE_RESET and update its comment.
It enables PCIe reset to fix link width 2x - 4x.
Signed-off-by: Bao Xiaowei <xiaowei.bao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
855873: An eviction might overtake a cache clean operation
Workaround: The erratum can be avoided by upgrading cache clean by
address operations to cache clean and invalidate operations. For
Cortex-A53 r0p3 and later release, this can be achieved by setting
CPUACTLR.ENDCCASCI to 1.
This patch is to implement the workaround for this erratum.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The CONFIG_SYS_DPAA_QBMAN define is used by DPAA1 freescale SOCs to
add device tree fixups that allow deep sleep in Linux. The define was
placed in header files included by a number of boards, but was not
explicitly documented in any of the Kconfigs. A description was added
to the drivers/networking menuconfig and default selection for
current SOCs that have this part
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds changes necessary to move functionality present in
PowerPC folders with ARM architectures that have DPAA1 QBMan hardware
- Create new board/freescale/common/fsl_portals.c to house shared
device tree fixups for DPAA1 devices with ARM and PowerPC cores
- Add new header file to top includes directory to allow files in
both architectures to grab the function prototypes
- Port inhibit_portals() from PowerPC to ARM. This function is used in
setup to disable interrupts on all QMan and BMan portals. It is
needed because the interrupts are enabled by default for all portals
including unused/uninitialised portals. When the kernel attempts to
go to deep sleep the unused portals prevent it from doing so
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sata registers PP2C and PP3C are used to control the configuration
of the PHY control OOB timing for the COMINIT/COMWAKE parameters
respectively. Calculate those parameters from port clock frequency.
Overwrite those registers with calculated values to get better OOB
timing.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Given gcc-6.1 and later we can now safely have strings discarded when
the functions are unused. This lets us drop certain cases of not
building something so that we don't have the strings brought in when the
code was discarded. Simplify the code now by dropping guards we don't
need now.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
commit 21a24c3bf3 ("fs/fat: fix case for FAT shortnames") made it
possible that get_name() returns file names with some upper cases.
find_directory_entry() must be updated to take this account, and use
case-insensitive functions to compare file names.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_AP325RXA
CONFIG_AP_SH4A_4A
CONFIG_CPU_SH_TYPE_R
CONFIG_ECOVEC
CONFIG_ESPT
CONFIG_MIGO_R
CONFIG_MPR2
CONFIG_MS7720SE
CONFIG_MS7722SE
CONFIG_MS7750SE
CONFIG_R0P7734
CONFIG_R2DPLUS
CONFIG_RSK7203
CONFIG_RSK7264
CONFIG_RSK7269
CONFIG_SH7752EVB
CONFIG_SH7753EVB
CONFIG_SH7757LCR
CONFIG_SH7763RDP
CONFIG_SH7785LCR
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
These macros are all defined once and never checked or used anywhere:
CONFIG_MACH_ASPENITE
CONFIG_MACH_DAVINCI_CALIMAIN
CONFIG_MACH_DOCKSTAR
CONFIG_MACH_EDMINIV2
CONFIG_MACH_GOFLEXHOME
CONFIG_MACH_GONI
CONFIG_MACH_GURUPLUG
CONFIG_MACH_KM_KIRKWOOD
CONFIG_MACH_OPENRD_BASE
CONFIG_MACH_SHEEVAPLUG
Almost all of them were only used for the mach_is_foo() logic in
arch/arm/asm/mach-types.h that were dropped in
commit f9dadaef8b ("arm: Re-sync asm/mach-types.h with
Linux Kernel v4.9")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Configure AM57xx EVMs for the exact PHY part that is
present on the various boards. This makes U-Boot apply
configurations needed for this PHY like centering the
FLP timing.
For configurations to take effect, DM_ETH needs to be
enabled. Do that too.
Tested on BeagleBoard x15 and AM571x IDK.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The 't208xrdb t4qds t102*' job is close to the time limit and
sometimes fails, so this splits it into 3 separate jobs.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Last user of this option went away in 2015 in commit:
d928664f41 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
BCM2835 ARM Peripherals doc shows gpio pins 4, 5, 6, 12 and 13 carry altenate
function, ALT5 for ARM JTAG
Signed-off-by: Henry Zhang <henryzhang62@yahoo.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add DT nodes to enable ARM_PL180_MMCI IP support for STM32F746
and STM32F769 discovery boards
There is a hardware issue on these boards, it misses a pullup on the GPIO line
used as card detect to allow correct SD card detection.
As workaround, cd-gpios property is not present in DT.
So SD card is always considered present in the slot.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board offers :
_ STM32F469NIH6 microcontroller featuring 2 Mbytes of Flash memory
and 324 Kbytes of RAM in BGA216 package
_ On-board ST-LINK/V2-1 SWD debugger, supporting USB reenumeration capability:
_ Mbed-enabled (mbed.org)
_ USB functions: USB virtual COM port, mass storage, debug port
_ 4 inches 800x480 pixel TFT color LCD with MIPI DSI interface and capacitive
touch screen
_ SAI Audio DAC, with a stereo headphone output jack
_ 3 MEMS microphones
_ MicroSD card connector
_ I2C extension connector
_ 4Mx32bit SDRAM
_ 128-Mbit Quad-SPI NOR Flash
_ Reset and wake-up buttons
_ 4 color user LEDs
_ USB OTG FS with Micro-AB connector
_ Three power supply options:
_ Expansion connectors and Arduino™ UNO V3 connectors
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This DT file comes from kernel v4.15-rc1
stm32f469-pinctrl.dtsi header has been updated with correct
STMicroelectronics Copyright.
Remove the paragraph about writing to the Free Software
Foundation's mailing address as requested by checkpatch.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This allows to controls the memory internal mapping at
address 0x0000 0000.
We can either map at 0x0000 0000 :
_ main flash memory
_ system flash memory
_ FMC bank1 (NOR/PSRAM 1 and 2)
_ embedded SRAM
_ FMC/SDRAM bank1
This is needed for future STM32F469-disco board
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32f7_gpio.c and pinctrl_stm32.c drivers
instead of board GPIO initialization.
Remove stm32_gpio.c which is no more used and migrate
structs stm32_gpio_regs and stm32_gpio_priv into
arch-stm32f4/gpio.h to not break compilation.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM clk_stm32f.c driver instead of dedicated
mach-stm32/stm32f4/clock.c.
Migrate periph_clock defines from stm32_periph.h directly in
CLK driver. These periph_clock defines will be removed when STMMAC,
TIMER2 and SYSCFG drivers will support DM CLK.
Enable also CLK flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In order to use common clock driver between STM32F4 and
STM32F7, remove clock_get() call
As APB_PSC is always set to 2, only case when
clock_get(CLOCK_AHB) != clock_get(CLOCK_APB1) is kept
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Remove serial_stm32.c driver and uart init from board file,
use available DM serial_stm32x7.c driver compatible for
STM32F4/F7 and H7 SoCs.
The serial_stm32x7.c driver will be renamed later with a more
generic name as it's shared with all STM32 Socs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This allows to support rcc MFD driver.
By enabling all these flags, we need to increase malloc area to avoid
crash during early stage.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
STM32F4 SoCs uses the same pinctrl block as found into
STM32F7 and H7 SoCs.
We can add "st,stm32f429-pinctrl" and "st,stm32f469-pinctrl"
compatible string into pinctrl_stm32.c.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32_sdram.c driver instead of board
SDRAM initialization.
For that, enable OF_CONTROL, OF_EMBED and STM32_SDRAM flags.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
_ Add gpio compatible and aliases for stm32f429
_ Add FMC sdram node with associated new bindings value to
manage second bank (ie bank 1).
_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
pwrcfg and gpio nodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
All these files comes from kernel v4.15-rc1.
Update some header with correct STMicroelectronics Copyright.
Remove the paragraph about writing to the Free Software
Foundation's mailing address as requested by checkpatch.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The DB-88F6820-AMC connects ethernet@34000 and ethernet@70000 which are
labeled as eth2 and eth0 in armada-38x.dts. The ethernet@30000 (eth1) is
not used on the AMC board.
This eliminates the following bootup message
Device 'ethernet@70000': seq 0 is in use by 'ethernet@34000'
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
this patch enable rockusb support on rk3288 based device.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
add a simple readme to introduce rockusb and tell people how to use it
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
this patch add rockusb command. the usage is
rockusb <USB_controller> <devtype> <dev[:part]>
e.g. rockusb 0 mmc 0
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>