This fixes:
cmd_bc3450.c:55:0: warning: "CONFIG_SYS_CPU" redefined [enabled by default]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
In commit 1a89a217f5 we moved most of the
required pads and mux data for USB to the essential list so that later
on we could NOT enable anything that wasn't essential unless otherwise
configured. This was however missing a few pandaboard-specific parts
which left for example USB ethernet non-functional.
Tested this on OMAP4430 ES2.2, OMAP4460 ES1.1 PANDA boards.
(Reworded by Tom Rini to be more precise about what the problem was)
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Tested-by: Tom Rini <trini@ti.com>
The bf527-ezkit boards are getting too big to fit into their reserved
flash space, so we need to use a lzma compressed logo.
Since the video driver code is very similar, add lzma compressed support
to all of the Blackfin video drivers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add I2C support.
Tested by placing a 24LC16 EEPROM into the U50 slot which comes empty from factory.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
When Trimslice is booted from serial flash, the boot ROM does this, so
U-Boot doesn't need to. However, booting from the SD slot for recovery
purposes, the boot ROM does not set up the pinmux for serial flash. Add
code to U-Boot to set this up, so that an SD-based recovery U-Boot image
can upgrade the U-Boot in serial flash.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Boards can override this to set up the pinmux correctly to access serial
flash.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Missed some boards after my tegra2_mmc.* -> tegra_mmc.* change, and
one instance of CONFIG_TEGRA2_SPI. MAKEALL -s tegra2 AOK, Seaboard MMC
AOK. Didn't test Tamonten, Paz00 or TrimSlice, as I have none here.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
GPIO PI6 can be used to obtain the write-protect status of an SD card
inserted into the SD slot.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The PI4 GPIO is used on Tamonten to reset carrier board peripherals.
Power sequencing hardware on the carrier pulls the reset low before
powering up the Tegra, and the CPU is supposed to signal readiness,
and therefore bring peripherals out of reset by pulling PI4 high.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The new gpio_early_init() function, which does nothing by default, can
be overridden by boards to configure GPIOs at an early stage.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Device tree support is required for working USB host support, which in
turn enables ethernet support.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Device tree support is required for working USB host support, which in
turn enables ethernet support.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This commit uses the common Tegra board implementation instead of
duplicating a lot of the code. In addition, the Plutux and Medcom
specific board files can be removed as the MMC/SD setup is common
among all Tamonten-based boards.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
* 'master' of git://git.denx.de/u-boot-arm: (212 commits)
ARM: cache: Move the cp15 CR register read before flushing the cache.
ARM: introduce arch_early_init_r()
PXA: Enable CONFIG_PREBOOT on zipitz2
ARM: mx28: Remove CONFIG_ARCH_CPU_INIT
No need to define CONFIG_ARCH_CPU_INIT.
add new board vl_ma2sc
MTD: SPEAr SMI: Add write support for length < 4 bytes
i2c: designware_i2c.c: Add support for the "i2c probe" command
rtc/m41t62: Add support for M41T82 with HT (Halt Update)
SPL: ARM: spear: Add SPL support for SPEAr600 platform
Makefile: Add u-boot.spr build target (SPEAr)
SPL: ARM: spear: Remove some objects from SPL build
SPL: lib/Makefile: Add crc32.c to SPL build
SPL: common/Makefile: Add image.c to SPL build
arm: Don't use printf() in SPL builds
GPIO: Add SPEAr GPIO driver
net: Multiple updates/enhancements to designware.c
cleanup/SPEAr: Define configuration flags more elegantly
cleanup/SPEAr: Remove unnecessary parenthesis
SPEAr: Correct SoC ID offset in misc configuration space
SPEAr: explicitly select clk src for UART
SPEAr: Remove CONFIG_MTD_NAND_VERIFY_WRITE to speed up NAND access
SPEAr: Enable ONFI nand flash detection for spear3xx and 6xx and evb
SPEAr: Enable CONFIG_SYS_FLASH_EMPTY_INFO macro
SPEAr: Correct the definition of CONFIG_SYS_MONITOR_BASE
SPEAr: Enable CONFIG_SYS_FLASH_PROTECTION
SPEAr: Enable dcache for fast file transfer
SPEAr: Enable autoneg for ethernet
SPEAr: Enable udc and usb-console support only for usbtty configuration
SPEAr: Enable usb device high speed support
SPEAr: Initialize SNOR in early_board_init_f
SPEAr: Change the default environment variables
SPEAr: Remove unused flag (CONFIG_SYS_HZ_CLOCK)
SPEAr: Add configuration options for spear3xx and spear6xx boards
SPEAr: Add basic arch related support for SPEAr SoCs
SPEAr: Add interface information in initialization
SPEAr: Add macb driver support for spear310 and spear320
SPEAr: Configure network support for spear SoCs
SPEAr: Place ethaddr write and read within CONFIG_CMD_NET
SPEAr: Eliminate dependency on Xloader table
SPEAr: Fix ARM relocation support
st_smi: Fixed page size for Winbond W25Q128FV flash
st_smi: Change timeout loop implementation
st_smi: Fix bug in flash_print_info()
st_smi: Change the flash probing method
st_smi: Removed no needed dependency on ST_M25Pxx_ID
st_smi: Fix smi read status
st_smi: Move status register read before modifying ctrl register
st_smi: Read status until timeout happens
st_smi: Enhance the error handling
st_smi: Change SMI timeout values
st_smi: Return error in case TFF is not set
st_smi: Add support for SPEAr SMI driver
mtd/NAND: Remove obsolete SPEAr specific NAND drivers
SPEAr: Configure FSMC driver for NAND interface
mtd/NAND: Add FSMC driver support
arm/km: remove calls to kw_gpio_* in board_early_init_f
arm/km: add implementation for read_dip_switch
arm/km: support the 2 PCIe fpga resets
arm/km: skip FPGA config when already configured
arm/km: redefine piggy 4 reg names to avoid conflicts
arm/km: cleanup km_kirkwood boards
arm/km: enable BOCO2 FPGA download support
arm/km: remove portl2.h and use km_kirkwood instead
arm/km: convert mgcoge3un target to km_kirkwood
arm/km: add kmcoge5un board support
arm/km: add kmnusa board support
arm: bugfix: save_boot_params_default accesses uninitalized stack when -O0
cm-t35: fix incorrect NAND_ECC layout selection
ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls.
ARM: OMAP4/5: Move USB pads to essential list.
ARM: OMAP4/5: Move USB clocks to essential group.
ARM: OMAP4/5: Move gpmc clocks to essential group.
ARM: OMAP4+: Move external phy initialisations to arch specific place.
omap4: Use a smaller M,N couple for IVA DPLL
da850/omap-l138: Enable auto negotiation in RMII mode
omap: am33xx: accomodate input clocks other than 24 Mhz
omap: emif: fix bug in manufacturer code test
omap: emif: deal with rams that return duplicate mr data on all byte lanes
OMAP4+: Force DDR in self-refresh after warm reset
OMAP4+: Handle sdram init after warm reset
ARM: OMAP3+: Detect reset type
arm: bugfix: Move vector table before jumping relocated code
Kirkwood: Add support for Ka-Ro TK71
arm/km: use spi claim bus to switch between SPI and NAND
arm/kirkwood: protect the ENV_SPI #defines
ARM: don't probe PHY address for LaCie boards
lacie_kw: fix CONFIG_SYS_KWD_CONFIG for inetspace_v2
lacie_kw: fix SDRAM banks number for net2big_v2
Kirkwood: add lschlv2 and lsxhl board support
net: add helper to generate random mac address
net: use common rand()/srand() functions
lib: add rand() function
kwboot: boot kirkwood SoCs over a serial link
kw_spi: add weak functions board_spi_claim/release_bus
kw_spi: support spi_claim/release_bus functions
kw_spi: backup and reset the MPP of the chosen CS pin
kirkwood: fix calls to kirkwood_mpp_conf
kirkwood: add save functionality kirkwood_mpp_conf function
km_arm: use filesize for erase in update command
arm/km: enable mii cmd
arm/km: remove CONFIG_RESET_PHY_R
arm/km: change maintainer for mgcoge3un
arm/km: fix wrong comment in SDRAM config for mgcoge3un
arm/km: use ARRAY_SIZE macro
arm/km: rename CONFIG option CONFIG_KM_DEF_ENV_UPDATE
arm/km: add piggy mac adress offset for mgcoge3un
arm/km: add board type to boards.cfg
AT91SAM9*: Change kernel address in dataflash to match u-boot's size
ATMEL/PIO: Enable new feature of PIO on Atmel device
ehci-atmel: fix compiler warning
AT91: at91sam9m10g45ek : Enable EHCI instead OHCI
Atmel : usb : add EHCI driver for Atmel SoC
Fix: AT91SAM9263 nor flash usage
Fix: broken boot message at serial line on AT91SAM9263-EK board
i.MX6 USDHC: Use the ESDHC clock
mx28evk: Fix boot by adjusting HW_DRAM_CTL29 register
i.MX28: Add function to adjust memory parameters
mx28evk: Fix PSWITCH key position
mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition
mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition
mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition
mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition
mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition
mx53ard: Remove unused CONFIG_MII_GASKET
mx6: Avoid writing to read-only bits in imximage.cfg
m28evk: use same notation to alloc the 128kB stack
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
* add support for board VL+MA2SC
* adds vl_ma2sc_config for standard NOR boot configuration
* adds vl_ma2sc_ram_config for RAM load configuration
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
Enable data cache with 1:1 mapping of DDR to enable fast file
transfer over tty which was doing lot of copy.
This feature is enabled only for flashing operation i.e. when
CONFIG_SPEAR_USBTTY is enabled.
This has been tested on SPEAr320, SPEAr600 and SPEAr900 evaluation
boards.
Following figures show an estimate on the performance improvements. The
test setup was a Linux host (not Windows) and involved measurement of
only binary transfer time, through kermit. The flash erase and flash
copy time would be unaffected by these patches.
Another thing is this that the timings remained more or less same across
ARM9 and Cortex based devices, hence reporting only one of the cases.
Before Enhancements
===================
$ time ukermit.small -p /dev/ttyACM0 -f spear320_uImage.img
Downloading file: 100.00% completed(2014080/2014080 bytes)
real 0m41.228s
user 0m0.002s
sys 0m0.064s
After Enhancements
==================
$ time ukermit.large -p /dev/ttyACM0 -f spear320_uImage.img
Downloading file: 100.00% completed(2014080/2014080 bytes)
real 0m5.441s
user 0m0.001s
sys 0m0.001s
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
flash reading is required earlier than flash_init is called since the env_init
is called before flash_init. This makes the smi_init necessary before env_init
being called.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds options for all the below mentioned configurations and
subsequently renames the include/configs/spearxxx.h files to spear3xx_evb.h,
spear6xx_evb.h etc to depict evaluation board configuration.
SPEAr3xx and SPEAr6xx boards can be compiled in following configurations
1. Environment placed in NAND
2. Console on usb device
3. Console on usb device with environment placed in NAND
4. SPEAr310 and SPEAr320 support environment variables in parallel
NOR flash.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Few Designware peripheral registers need to be modified based on the
ethernet interface selected by the board. This patch supports interface
information in ethernet driver
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
SPEAr310 and SPEAr320 SoCs have an extra ethernet controller. The
driver for this device is already supported by u-boot, so configuring
board configuration file and defining base addresses etc to make use
of the common driver
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
ethaddr can be optionally read from i2c memory. So, chip_config command supports
reading/writing hw mac id into i2c memory. Placing this code within
CONFIG_CMD_NET as this would only be needed when network interface is configured
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Xloader table was used primarily to inform u-boot about the DDR size. However,
now the ddr size is calculated at runtime which eliminates any need for the
Xloader table. So removing this unnecessary code.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
While the u-boot code is running from the flash, it is essential that no access
is made to the bss segment. This is due to the fact that .rel.dyn and .bss areas
overlap and former contains information used in relocation. In SPEAr, this was
not taken into consideration. As a result, while the relocation wasn't complete,
dram_init populated an uninitialized global variable resulting in corruption of
.rel.dyn area, which resulted in u-boot crash.
This commit fixes this problem by removing code that accesses bss segment
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Since FSMC is a standard IP and it supports different memory interfaces, it
is supported independent of spear platform and spear is configured to use that
driver for interfacing with the NAND device
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
These functions tried to access two static tables before relocation
(board_early_init_f is executed before relocation). But these static
tables lie in the bss section which is not valid before relocation.
These accesses then overwrote some parts of u-boot binary before it was
relocated. For the kmnusa build, this results in a corrupted important
env variable (bootcmd) but it may be that some other parts of the u-boot
binary are corrupted.
This patch solves this problem by moving all the kw_gpio_* calls to
board_init, which should be early enough in the boot sequence. The only
calls that could not be moved is the one for the SOFT (bitbang) I2C, and
they have been replaced by a direct access to the GPIO dataout Control
register to set the two GPIOs as output.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Add a function to read the dip_switch on kmcoge5un. If the
switch is set the actual_bank is set to 0 and this SW is
booted.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
The PCIe FPGAs now have to support 2 resets: one for the non traffic
affecting part (PCIe) and one for the traffic affecting part.
When the FPGA is not reconfigured, we only reset the PCIe part.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
In order to be able to perform board resets without interrupting the
traffic, the configuration of an already properly configured FPGA is
skipped.
This is because some PCIe FPGAs embed some other function that must
continue to work over reset.
It is then the responsibility of the application to trigger a
reconfiguration when needed. This is done by lowering the FPGA_INIT_B
pin for delaying the configuration to u-boot @ next reboot, and then
lower the FPGA_PROGRAM_B signal.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Some very similar #defines for reg addresses are used in a later patch
(managed_switch support for km_arm).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This adds a first support of the FPGA download for a PCIe FPGA based
on the BOCO2 CPLD.
This takes place in 3 steps, all done accessing the SPICTRL reg of the
BOCO2:
1) start the FPGA config with an access to the FPGA_PROG bit
2) later in the boot sequence, wait for the FPGA_DONE bit to toggle to 1
for the end of the FPGA configuration (with a timeout)
3) reset the FPGA
4) finally remove the access to its config EEPROM from the FPGA so that
the CPU can update the FPGA configuration when the kernel is running
The boards with a PCIe FPGA but without BOCO2 still are supported.
The config option name is CONFIG_KM_FPGA_CONFIG
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The additional headerfile is unneeded here, we can use the generic
km_kirkwood.h instead. And we can use the better config option
KM_PIGGY4_88E6061 for the specific features for boards with this
design in km_arm.c.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Use the generic header km_kirkwood.h and get rid of the
board specific header.
changes for v2: rebased because of changes in other patches
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
For u-boot this board is similar to mgcoge3un. But some differences
are present. We have a different SDRAM on it and therefore a new
SDRAM config file. Additionaly this board has a direct MAC/MAC
connection from the kirkwood to a marvell simple switch without a
phy inbetween, this needs a new configuration for the mvgbe driver.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This board is similar to portl2, but it has the u-boot environment
in a SPI NOR flash and not in an i2c eeprom like portl2 have.
Some other details:
- IVM EEPROM is at adress: pca9547:70:9
- PCI is enabled
- PIGGY4 is connected via MV88E6352 simple switch. There is no phy
between the simple switch and the kirkwood.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
USB module pads are getting enabled under non-essential
group. These will be required for fastboot, tftp support.
So move this to essential list to have them working when
non-essential pads are no more muxed.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
We overwrite these weak functions from the kirkwood spi code to
use our own method to be able to switch between the SPI NOR and
the NAND flash. This is needed e.g. to update the u-boot. The former
command do_spi_toggle can therefore be removed. And the usage of
this command is removed from the u-boot update command in the
u-boot environment.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The command miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr) always
returns 8 for the PHY address. It is the reset value for the PHY
Address Register. Obviously, this default value could be incorrect.
Moreover, as the PHY address is well known, there is no need to
auto-detect it.
Now, the PHY address must given as a parameter to the PHY initialization
function. Additionally this patch also fixes some aesthetic issues.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
This patch adds support for both the Linkstation Live (LS-CHLv2) and
Linkstation Pro (LS-XHL) by Buffalo.
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
With the new second save argument introduced by the previous patch, all
the calls to the function had to be fixed.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
On at91sam platforms, u-boot grew larger than the allocated size in
dataflash, the layout was:
bootstrap 0x00000000
ubootenv 0x00004200
uboot 0x00008400
kernel 0x00042000
fs 0x00252000
u-boot with the defconfig doesn't seem to fit in 0x42000 - 0x8400 =
0x39C00 bytes anymore.
Now, the layout is:
bootstrap 0x00000000
ubootenv 0x00004200
uboot 0x00008400
kernel 0x00084000
fs 0x00294000
Signed-off-by: Alexandre Belloni <alexandre.belloni@piout.net>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
