Add missing PCI range for translating DRAM to bus addresses.
This fixes e.g. PCI NIC interface and allows network to work
in QEMU.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pass -m4 instead of -m4-nofpu to GCC versions which do not support
the -m4-nofpu option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since binutils 2.30 , the resulting U-Boot binary was incorrectly linked
against address 0 instead of text base, fix it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
According to the latest am572x[1] and dra74x[2] data manuals, mmc3
default, hs, sdr12 and sdr25 modes use iodelay values given in
MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is
selected and correct iodelay values are configured.
[1] http://www.ti.com/lit/ds/symlink/am5728.pdf
[2] http://www.ti.com/lit/ds/symlink/dra746.pdf
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
API get_ti_sci_handle() is relying on the device-tree node name
to be "dmsc" for probing the ti_sci device. But with the introduction
of debug messages for dmsc, the node name changed to dmsc@44083000.
Because of this ti_sci is never probed cause a boot failure. Instead
of relying on device-tree node name, use the first available firmware
node for probing ti_sci.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The da8xx GPIO driver is available with DM_GPIO support. This
patch enables the CMD_GPIO, CMD_DM, and DM_GPIO and DA8XX_GPIO.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add device tree from Linux for driver model conversion
and enable OF_CONTROL. This will remove the following compile
warning:
==================================================
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
===================================================
Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
In SerDes protocol 0x13BB, lane C was erroneously assigned
to PCIE1, this is now updated to PCIE2
Fixes: 36f50b7523 ("armv8: ls1028a: Add other serdes
protocal support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The correct config entry is CONFIG_PCIE_LAYERSCAPE and this
typo results in skipping the fixup of Linux PCIe DT nodes.
Also enable the fixup when Layerscape Gen4 controller driver
is enabled.
Fixes: 4da0e52c9d (armv8: fsl-layerscape: fix config dependency
for layerscape pci code)
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
By default, i2c input clock is programmed at
platform clk / 2 in u-boot, but this is not
correct for all the platforms,
Update I2C clock divider's default values as per
SoC (LS1012A, LS1028A, LX2160A and LS1088A).
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The SP805-WDT module on LS1028A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com>
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the device-tree structure describing the MUX in board dts.
QDS board has an on-board RGMII PHY and 4 slots for extension cards.
All these can be accessed over MDIO through a MDIO MUX controlled
over I2C.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Use obj-$(config) instead of #ifdef $config to make the code looks
clean, and move the misc_init for U-Boot proper only.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The rk3188/Makefile already depends on !TPL_BUILD, so no need to add
this again in parent Makefile, remove it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
For sake of consistency use spaces over TABs in ASL code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Intel iDMA 32-bit controller has 17 bits for the maximum block size value.
Due to nature of the binary number representation the maximum value is
2^17 - 1. The original code misses the latter part in equation.
Fixes: 5e99fde34a ("x86: tangier: Populate CSRT for shared DMA controller")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Per PCI firmware specification the ACPI has to reserve the memory
which is defined as PCI ECAM.
Fixes: 39665beed6 ("x86: tangier: Enable ACPI support for Intel Tangier")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
GCC 9.2 starts complaining about possible pointer misalignment of
pointers to the unpacked (alignment=4) structures in the packed
(alignment=1) ones:
CC arch/x86/cpu/tangier/acpi.o
arch/x86/cpu/tangier/acpi.c: In function ‘acpi_create_fadt’:
arch/x86/cpu/tangier/acpi.c:22:37: warning: taking address of packed
member of ‘struct acpi_fadt’ may result in an unaligned pointer value
[-Waddress-of-packed-member]
22 | struct acpi_table_header *header = &(fadt->header);
CC arch/x86/lib/acpi_table.o
arch/x86/lib/acpi_table.c: In function ‘acpi_create_spcr’:
arch/x86/lib/acpi_table.c:366:37: warning: taking address of packed
member of ‘struct acpi_spcr’ may result in an unaligned pointer value
[-Waddress-of-packed-member]
366 | struct acpi_table_header *header = &(spcr->header);
Fix the potential issues by annotating embedded structures with
__packed even though they are packed naturally.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add GCC version number in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Use efi_add_conventional_memory_map() to configure EFI conventional memory
properly with ram_top value. This will give 32-bit mode U-Boot proper
conventional memory regions even if e820 has an entry which is greater than
32-bit address space.
Signed-off-by: Aiden Park <aiden.park@intel.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[bmeng: fixed some typos in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
If a crash occurs, show the loaded UEFI images to facilitate analysis.
This is an example output:
=> bootefi 0x1000000
Found 0 disks
Hello world of bugs!
Invalid Opcode (Undefined Opcode)
EIP: 0010:[<06ceb06e>] EFLAGS: 00010206
Original EIP :[<fec9906e>]
EAX: 00000000 EBX: 06cec000 ECX: 00000fd0 EDX: 00000001
ESI: 06ced18a EDI: 07d0fe10 EBP: 07fe27a0 ESP: 07d0fde0
DS: 0018 ES: 0018 FS: 0020 GS: 0018 SS: 0018
CR0: 00000033 CR2: 00000000 CR3: 00000000 CR4: 00000000
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Stack:
0x07d0fde8 : 0x00000000
0x07d0fde4 : 0x06ced040
--->0x07d0fde0 : 0x07fe27a0
0x07d0fddc : 0x00010206
0x07d0fdd8 : 0x00000010
0x07d0fdd4 : 0x06ceb06e
UEFI image [0x06cea000:0x06cf0fff] pc=0x106e '/bug-i386.efi'
### ERROR ### Please RESET the board ###
With the additional information provided by this patch we know that the
problem occurred 0x106e after the load address of bug-i386.efi.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Now that we are able to get the size of high memory from QEMU,
report its memory range as usable ram.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
At present only size of memory that is below 4GiB is retrieved from
QEMU. Add a function that gets size of memory that is above 4GiB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
This extracts getting memory size logic in dram_init() to a separate
routine qemu_get_low_memory_size(). No functional changes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Every x86 platform provides board_get_usable_ram_top(), hence there
is no need to provide a weak version board_get_usable_ram_top(), not
to mention there is another weak version board_get_usable_ram_top()
in common/board_f.c.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Using ACPI predefined macros, such as Zero or One, will reduce a binary
size of resulting ACPI tables.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: manually fixed the conflicts when applying]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
-----BEGIN PGP SIGNATURE-----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=hWTf
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2019.10' of https://github.com/mbgg/u-boot
- fix mailbox status register used for polling
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
This clock has a different mbox ID so have this included in the relevant
header file.
Signed-off-by: Andrei Gherzan <andrei@balena.io>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Define two target configs for Raspberry Pi 4 (32 and 64bit) and the
corresponding BCM2838* configs.
Be aware of the current limitation in firmware which requires an
explicit configuration to force the arm in 64bit mode when the
respective target is used.
Signed-off-by: Andrei Gherzan <andrei@balena.io>
[mb: rename BCM2838 -> BCM2711]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Devices of bcm283x have different base address, depending if they are on
bcm2835 or bcm2836/7. Use BCM283x_BASE depending on the SoC you want to
build and only add the offset in the header files.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Andrei Gherzan <andrei@balena.io>
Before we can send a message to the mailbox we have to check that there
is space to do so. Therefore we poll the status register. But up to now
the wrong status register, the one of mailbox 0, was checked. Fix this
by polling the status regiser of mailbox 1.
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[mb: rename registers and update commit message]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Add nodes for the Aspeed SD controllers with their necessary properties.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Implicitly Marvell MDIO driver uses DT node names for devices, but in this
case that is not unique. Set MDIO device names for master/slave to
cpm/cps.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Create drivers/net/fsl-mc/Kconfig and move fsl-mc specific configs
from arch/arm/cpu/armv8/fsl-layerscape/Kconfig to this new Kconfig
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
These are some very late changes mostly required to get 64-bit
division working on ARC boards.
For that we had to import missing parts of libgcc and add compiler
flags to EMSDP which otherwise used very simple profile for compliation.
And while at it another fix for EM SDP initialization is inluded as well.
As reported by Kever here [1] we were unable to compile 64-bit division
code due to missing definition of __udivdi3().
Import its implementation and __udivmoddi4() as its direct dependency
from today's libgcc [2].
[1] https://patchwork.ozlabs.org/patch/1146845/
[2] 5d8723600b
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Use CCTL command to do d-cache write back
and invalidate instead of fence.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When L2 node exists inside cpus node, uclass_get_device
can not parse L2 node successfully. So move it outside
from cpus node.
Also add tag-ram-ctl and data-ram-ctl attributes for
v5l2 cache controller driver. This can adjust timing
by requirement from dtb to improve performance.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
