The '#' used as comments in the files cause the preprocessor
trouble, so change to /* */.
The mkimage command which uses this preprocessor output
was moved to arch/arm/imx-common/Makefile
.gitignore was updated to ignore .cfgtmp files.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Add DVI output support and make it the default video output.
Currently the CLAA WVGA panel is supported, but this panel has to be purchased
separately, so using the DVI output as the default would allow more people to
try the splash screen feature on a mx51evk.
If someone still wants to use the CLAA WVGA, just set the panel variable as:
set panel claa
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add support for the Seiko 4.3'' WVGA panel on mx53loco.
By default, the CLAA WVGA panel is selected.
In order to support the Seiko panel, the enviroment variable 'panel' must be
set to 'seiko'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Make the error handling more robust.
Check if each one of the PMIC writes fail and if they do, just return
immediately.
Also, print the cause for the failures.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
commit c73368150 (pmic: Extend PMIC framework to support multiple instances
of PMIC devices) introduced an extra 'retval' variable, but this is not
necessary since we have already the variable 'ret' in place.
So use 'ret' to store the return values from the pmic related calls and remove
'retval'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The on-board number of available usdhc devices is something board
specific. The patch moves CONFIG_SYS_FSL_USDHC_NUM out of
mx6qsabre_common.h and adds usdhc2 and usdhc4 support for mx6qsabresd
board.
To keep the default mmc device for environment same as before (usdhc3),
it moves CONFIG_SYS_MMC_ENV_DEV out of mx6qsabre_common.h and changes
it to 1 for mx6qsabresd.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit c733681 (pmic: Extend PMIC framework to support multiple instances
of PMIC devices) mx53loco fails to allocate the memory for PMIC:
U-Boot 2013.01-rc2-dirty (Dec 20 2012 - 15:55:01)
Board: MX53 LOCO
I2C: ready
DRAM: 1 GiB
pmic_alloc: No available memory for allocation!
pmic_init: POWER allocation error!
CPU: Freescale i.MX53 family rev2.0 at 800 MHz
Reset cause: POR
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Calling the PMIC related functions at a later stage, ie, from board_late_init()
fixes the issue.
Reported-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
This converts MPC8313ERDB NAND boot to use the new SPL infrastructure.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit c73368150 (pmic: Extend PMIC framework to support multiple instances
of PMIC devices) has incorrectly passed the PMIC name under the FSL PMIC case.
Fix that by passing "FSL_PMIC" as the parameter of pmic_get.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Make the necessary adaptions for the new PMIC framework, so that mx25pdk can
be built again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Conflicts:
drivers/power/power_fsl.c
include/configs/mx35pdk.h
include/configs/mx53loco.h
include/configs/woodburn_common.h
board/woodburn/woodburn.c
These boards still use the old old PMIC framework, so they
do not merge properly after the power framework was merged into
mainline.
Fix all conflicts and update woodburn to use Power Framework.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Single rank UDIMM timing has been verified with HMT325U7BFR8C-H9 for speed
800, 900, 1000, 1200, 1300MT/s.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P5040DS reference board (a.k.a "Superhydra") is an enhanced version of
P3041DS/P5020DS ("Hydra") reference board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
There were a number of shared files that were using
CONFIG_SYS_MPC85xx_DDR_ADDR, or CONFIG_SYS_MPC86xx_DDR_ADDR, and
several variants (DDR2, DDR3). A recent patchset added
85xx-specific ones to code which was used by 86xx systems.
After reviewing places where these constants were used, and
noting that the type definitions of the pointers assigned to
point to those addresses were the same, the cleanest approach
to fixing this problem was to unify the namespace for the
85xx, 83xx, and 86xx DDR address definitions.
This patch does:
s/CONFIG_SYS_MPC8.xx_DDR/CONFIG_SYS_MPC8xxx_DDR/g
All 85xx, 86xx, and 83xx have been built with this change.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Tested-by: Andy Fleming <afleming@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This allows DDR configuration to be deferred to the final U-Boot image,
which is able to make use of SPD data. The SPL itself cannot use SPD due
to code size constraints. It previously used fixed register values for
DDR configuration, and those values did not work on the p2020rdb-pca
board I tested with. It's possible that different revisions of the board
require different settings. Using SPD eliminates that problem.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
- Sort by address, and fix column alignment
- Don't label things as localbus that aren't. Instead, put chipselect
info at the end of the description for localbus windows. Note that
NAND/NOR have their chipselects swapped when booting from NAND, and CS2
can be either PMC or VSC7385 depending on hwconfig.
- Shrink NAND to the 32K that's actually mapped in the localbus
- Assign an address and size to L2 SRAM. Remove the similarly named
but unintelligible "L2 SDRAM(REV.)".
- Remove the untrue comment about L1 stack being mapped with TLB0.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Introduces CONFIG_SPL_RELOC_TEXT_BASE and CONFIG_SPL_RELOC_STACK.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Add support for the OTG port on the mx35pdk Personality board.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
The inclusion of LCD patch into mx53loco breaks the build when
CONFIG_VIDEO is disabled. Fix this by splitting the video
related stuff to a new file.
Also rename the function lcd_iomux to setup_iomux_lcd to make the
namings aligned with the other iomux functions.
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The inclusion of LCD patch into mx51evk breaks the build when
CONFIG_VIDEO is disabled. Fix this by splitting the video related
stuff to a new file.
Also rename the function lcd_iomux to setup_iomux_lcd to make the
namings aligned with the other iomux functions.
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The PMIC framework has been extended to support multiple instances of
the variety of devices responsible for power management.
This change allows supporting of e.g. fuel gauge, charger, MUIC (Micro USB
Interface Circuit).
Power related includes have been moved to ./include/power directory.
This is a first of a series of patches - in the future "pmic" will be
replaced with "power".
Two important issues:
1. The PMIC needs to be initialized just after malloc is configured
2. It uses list to hold information about available PMIC devices
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
fdt.c:91:78: warning: Using plain integer as NULL pointer
fdt.c:103:78: warning: Using plain integer as NULL pointer
speed.c:55:11: warning: symbol 'corecnf_tab' was not declared. Should it be static?
speed.c:519:5: warning: symbol 'do_clocks' was not declared. Should it be static?
mpc8313erdb.c:73:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:74:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:75:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:76:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:79:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:80:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:81:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:82:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:85:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:86:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:87:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:88:17: warning: obsolete struct initializer, use C99 syntax
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
fsl_corenet_serdes.c:485:6: warning: symbol '__soc_serdes_init' was not declared. Should it be static?
cpu_init.c:185:6: warning: symbol 'invalidate_cpc' was not declared. Should it be static?
bcsr.c:28:27: warning: non-ANSI function declaration of function 'enable_8568mds_duart'
bcsr.c:39:33: warning: non-ANSI function declaration of function 'enable_8568mds_flash_write'
bcsr.c:46:34: warning: non-ANSI function declaration of function 'disable_8568mds_flash_write'
bcsr.c:53:29: warning: non-ANSI function declaration of function 'enable_8568mds_qe_mdio'
bcsr.c:28:33: warning: non-ANSI function declaration of function 'enable_8569mds_flash_write'
bcsr.c:33:34: warning: non-ANSI function declaration of function 'disable_8569mds_flash_write'
bcsr.c:38:28: warning: non-ANSI function declaration of function 'enable_8569mds_qe_uec'
bcsr.c:63:47: warning: non-ANSI function declaration of function 'disable_8569mds_brd_eeprom_write_protect'
ngpixis.c:245:1: error: directive in argument list
ngpixis.c:247:1: error: directive in argument list
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The M54418TWR lds file need to update since commit:
8b493a5236
common: Discard the __u_boot_cmd section
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
mx25pdk has a Ethernet port that is connected to its internal FEC controller.
In order to power up the Ethernet PHY (DP83640) it is necessary to communicate
with the MC34704 PMIC via I2C.
Make the FEC ethernet port functional
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx25pdk has a SD/MMC slot connected to esdhc1.
Add support for it and allow the environment variables to be saved into SD/MMC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch modifies start.S for the arm1136 to make it
conform to start.S in armv7 architecture, to make it
usable if the SPL framework is used.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add Freescale MCF54418TWR ColdFire development board support.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
The T4240QDS is a high-performance computing evaluation, development and
test platform supporting the T4240 QorIQ Power Architecture™ processor.
SERDES Connections
32 lanes grouped into four 8-lane banks
Two “front side” banks dedicated to Ethernet
Two “back side” banks dedicated to other protocols
DDR Controllers
Three independant 64-bit DDR3 controllers
Supports rates up to 2133 MHz data-rate
Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller
QIXIS System Logic FPGA
Each DDR controller has two DIMM slots. The first slot of each controller
has up to 4 chip selects to support single-, dual- and quad-rank DIMMs.
The second slot has only 2 chip selects to support single- and dual-rank
DIMMs. At any given time, up to total 4 chip selects can be used.
Detail information can be found in doc/README.t4qds
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add code for configuring VSC3316/3308 crosspoint switches
Add README to understand the APIs
- VSC 3316/3308 is a low-power, low-cost asynchronous crosspoint switch
capable of data rates upto 11.5Gbps. VSC3316 has 16 input and 16
output ports whereas VSC3308 has 8 input and 8 output ports.
Programming of these devices are performed by two-wire or four-wire
serial interface.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
According to new QIXIS system definition, update QIXIS registers set
to add present2 register instead of obsolete ctl_sys2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Add section for the linker-generated lists into all possible linker
files, so that everyone can easily use these lists. This is mostly
a mechanical adjustment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
QIXIS FPGA layout defines the address of registers but The actual register bit
implementation is board-specific,
So avoid use of magic numbers as it may vary across different boards's QIXIS
FPGA implementation.
Also, Avoid board specific defines in common/qixis.h
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Adds support for HDMI, two LVDS panels and one RGB panel to
the SABRE-Lite board.
Displays supported:
HDMI - 1024 x 768 for maximum compatibility
Hannstar-XGA - 1024 x 768 LVDS (Freescale part number MCIMX-LVDS1)
wsvga-lvds - 1024 x 600 LVDS (Boundary p/n Nit6X_1024x600)
wvga-rgb - 800 x 480 RGB (Boundary p/n Nit6X_800x480)
Since the ipuv3_fb display driver currently supports only a single display,
this code auto-detects panel by probing the HDMI Phy for Hot Plug Detect
or the I2C touch controller of the LVDS and RGB displays in the priority
listed above.
Setting 'panel' environment variable to one of the names above will
override auto-detection.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
The kernel from Freescale expects that the bootloader passes the board revision.
Read the board revision and pass it via get_board_rev().
Without passing the board revision the kernel does not operate properly as the
initialization of peripherals are different in revA versus revB boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
On mxc, each SDHC instance has a dedicated clock, so gd->sdhc_clk is not
suitable for the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).
This patch fixes this issue by adding a configuration field for the SDHC input
clock frequency.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Andy Fleming <afleming@gmail.com>
Clean up mx35 lowlevel_init:
- Indent with tabs.
- Fix comments.
- Use defined values instead of literal constants.
- Use defined macros instead of duplicating code.
- Use macro parameters with default values instead of #define'd configs.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The CSI PODF bit-field used by the previous code for the i.MX31 CCM PDR0
register is actually composed of two bit-fields: one pre-divider and one
post-divider. This patch fixes the CCM access macros and the code using them
accordingly.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Define default SoC input clock frequencies for i.MX5/6 in order to get rid of
duplicated definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input
Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx6qsabresd has a AR8031 Gigabit PHY.
Add support for it.
Also increase CONFIG_SYS_MALLOC_LEN so that FEC buffer allocation does not fail.
Tested on 1Gbp and 100Mbps networks.
Suggested-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
mx6qsabresd is a board based on mx6q SoC with the following features:
- 1GB of DDR3
- 1 USB OTG port
- 1 HDMI output port
- SPI NOR
- LVDS panel
- Gigabit Ethernet
- Camera Connector
- eMMC and SD card slot
- Audio
Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
fecmxc_mii_postcall() is specific to the KSZ9021 PHY on m28evk and
should not be used on mx28evk, which has LAN8270 instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG
information.
If this data is not present, the kernel misconfigures the TZIC, which results in
the timer interrupt handler never being called, so the kernel deadlocks while
calibrating its delay.
Suggested-by: Greg Topmiller <Greg.Topmiller@jdsu.com>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Add support for the onboard eSDHC MMC controller. The hardware on the
MPC8308RDB has the following errata:
- ESDHC111: manual asynchronous CMD12 is broken
- DMA is broken (PIO works)
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
[added include fsl_esdhc header to prevent implicit declarations of
fsl_esdhc_mmc_init() and fdt_fixup_esdhc()]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The SPI pins are routed to header J8 for testing SPI functionality. A
Spansion flash has been wired up and tested on this header.
This patch breaks support for the second TSEC interface, since the GPIO
pin used as a chip select is pinmuxed with some of the TSEC pins.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Recent conversion from mx28_adjust_memory_params to mxs_adjust_memory_params
missed to update mx28evk, which caused the board not to boot.
Apply the conversion so that the board can boot again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Align the SSP clock speed with oscilator to achieve higher transfer
stability.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
The cache snooping feature of Freescale's eSDHC IP is not available on i.MX, so
disable it globally for this architecture. This avoids setting no_snoop for all
i.MX boards, and it prevents setting a reserved bit of a reserved register if
fsl_esdhc_mmc_init() is used on i.MX, like in
arch/arm/cpu/armv7/imx-common/cpu.c/cpu_mmc_init().
Since no_snoop was only used on i.MX, get rid of it BTW.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
The DRAM initialization, after SPL has complete, is exactly the same
for all mxs SoCs so we should name it accordinly.
The following boards has been changed:
* apx4devkit
* m28evk
* mx28evk
* sc_sps_1
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
Each i.MX has its own gpio.h, defining the same structure.
The internal GPIO controller has the same layout
(at least for the register used by u-boot) and can be shared.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Matt Sealey <matt@genesi-usa.com>
This allows a watchdog reset to start the ROM's
usb/serial downloader, or boot from an sdcard.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
This gets us rid of duplication of the same file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
On this board, the console is always set to the serial line.
Do not allow to overwrite it when video is enabled.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
On this board, the console is always set to the serial line.
Do not allow to overwrite it when video is enabled.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
LAW init is skipped in the SPL payload because it's assumed that the SPL
has taken care of it -- so make sure the SPL loads all the LAWs as is
done on other boards.
This bug was introduced by:
commit 4589728e21
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Fri Nov 11 08:14:53 2011 -0600
powerpc/85xx: Fix builds of P1020/P2020RDB-PC_36BIT_NAND
Size grew a bit so nand-spl didn't fit in 4k, reduce done by removing
LAW entries not needed during SPL phase.
Signed-off-by: Scott Wood <scottwood@freescale.com>
The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
enum board_slots contained six values, where SLOT1 == 1, SLOT2 == 2, and
so on. This is pointless, so remove it. Also move the lane_to_slot[]
array to the top of the file so that it can be used by other functions.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In order to figure out which SerDes lane a given Fman port is connected
to, we need a function that maps the fm_port namespace to the srds_prtcl
namespace.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Using the raw value of 0x80000000 directly in the code can
lead to "count the zeros" bugs like that fixed in commit
718e9d13b98 ("MPC85xxCDS: Fix missing LCRR_DBYP bits for
66-133MHz LBC")
Change all existing raw values to use the symbolic value of
LCRR_DBYP instead.
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
There was an extra 0 in front of the value we were using to mask,
remove it to improve the code.
Also fix the value written to ddr_sdram_cfg to set the bus width
properly to 16 bits
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Provides a tool to build boot Image for PBL(Pre boot loader) which is
used on Freescale CoreNet SoCs, PBL can be used to load some instructions
and/or data for pre-initialization. The default output image is u-boot.pbl,
for more details please refer to doc/README.pblimage.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>