Now 405EZ ports also show upon bootup from which boot device
they are configured to boot:
U-Boot 1.2.0-gd3832e8f-dirty (Apr 18 2007 - 07:47:05)
CPU: AMCC PowerPC 405EZ Rev. A at 199.999 MHz (PLB=133, OPB=66, EBC=66 MHz)
Bootstrap Option E - Boot ROM Location EBC (32 bits)
16 kB I-Cache 16 kB D-Cache
Board: Acadia - AMCC PPC405EZ Evaluation Board
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes changes the i2c_init(...) function to use the function
get_OPB_freq() rather than calculating the OPB speed by
sysInfo.freqPLB/sysInfo.pllOpbDiv. The get_OPB_freq() function is
specific per processor. The prior method was not and so was calculating
the wrong speed for some PPC4xx processors.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Fix a bug in the auto calibration routine. This driver now runs
more reliable with the tested modules. It's also tested with
167MHz PLB frequency (667MHz DDR2 frequency) on the Katmai.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds some 4xx GPIO functions. It also moves some of the
common code and defines into a common 4xx GPIO header file.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the new AMCC 405EZ PPC. It is in
preparation for the AMCC Acadia board support.
Please note that this Acadia/405EZ support is still in a beta stage.
Still lot's of cleanup needed but we need a preliminary release now.
Signed-off-by: Stefan Roese <sr@denx.de>
The AMCC Luan now uses the common 440SP(e) DDR SPD code for DDR
inititializition. This includes DDR auto calibration and support
for different DIMM modules, instead of the fixed setup used in
the earlier version.
This patch also enables the cache in FLASH for the startup
phase of U-Boot (while running from FLASH). After relocating to
SDRAM the cache is disabled again. This will speed up the boot
process, especially the SDRAM setup, since there are some loops
for memory testing (auto calibration).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a problem that occurs when 2 DIMM's are
used. This problem was first spotted and fixed by Gerald Jackson
<gerald.jackson@reaonixsecurity.com> but this patch fixes the
problem in a little more clever way.
This patch also adds the nice functionality to dynamically
create the TLB entries for the SDRAM (tlb.c). So we should
never run into such problems with wrong (too short) TLB
initialization again on these platforms.
As this feature is new to the "old" 44x SPD DDR driver, it
has to be enabled via the CONFIG_PROG_SDRAM_TLB define.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch updates the recently added Katmai board support. The biggest
change is the support of ECC DIMM modules in the 440SP(e) SPD DDR2
driver.
Please note, that still some problems are left with some memory
configurations. See the driver for more details.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the DDR2 controller used on the
440SP and 440SPe. It is tested on the Katmai (440SPe) eval
board and works fine with the following DIMM modules:
- Corsair CM2X512-5400C4 (512MByte per DIMM)
- Kingston ValueRAM KVR667D2N5/512 (512MByte per DIMM)
- Kingston ValueRAM KVR667D2N5K2/2G (1GByte per DIMM)
This patch also adds the nice functionality to dynamically
create the TLB entries for the SDRAM (tlb.c). So we should
never run into such problems with wrong (too short) TLB
initialization again on these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Since the existing 4xx SPD SDRAM initialization routines for the
405 SDRAM controller and the 440 DDR controller don't have much in
common this patch splits both drivers into different files.
This is in preparation for the 440 DDR2 controller support (440SP/e).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for multiple I2C busses on the PPC4xx
platforms. Define CONFIG_I2C_MULTI_BUS in the board config file
to make use of this feature.
It also merges the 405 and 440 i2c header files into one common
file 4xx_i2c.h.
Also the 4xx i2c reset procedure is reworked since I experienced
some problems with the first access on the 440SPe Katmai board.
Signed-off-by: Stefan Roese <sr@denx.de>
Previously the strapping DCR/SDR was read to determine if the internal PCI
arbiter is enabled or not. This strapping bit can be overridden, so now
the current status is read from the correct DCR/SDR register.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a problem with an incorrect setup for the refresh
timer of the 44x DDR controller in the file cpu/ppc4xx/sdram.c
Signed-off-by: Stefan Roese <sr@denx.de>
This code will optimize the DDR2 controller setup on a board specific
basis.
Note: This code doesn't work right now on the NAND booting image for the
Sequoia board, since it doesn't fit into the 4kBytes for the SPL image.
Signed-off-by: Stefan Roese <sr@denx.de>
Patch below corrects the setting of the zmiifer register, it was
overwritting the register rather than ORing the settings.
Signed-off-by: Neil Wilson <NWilson@airspan.com>
Signed-off-by: Stefan Roese <sr@denx.de>
