Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early
verion silicons. This workaround detects if the eTSEC Rx logic is properly
initialized, and reinitialize the eTSEC Rx logic.
Signed-off-by: Gong Chen <g.chen@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
TBI PHY address (TBIPA) register has been set in general frame manager
phy init funciton dtsec_init_phy() in drivers/net/fm/eth.c
So remove the duplicate code on QorIQ frame manager Ethernet related
platforms, which include Hydra board, P4080DS board and P2041rdb board.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new MPC8360EMDS board changes the oscillator to 33.33MHz
in order to support QE 500MHz since 2008.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* 'master' of git://git.denx.de/u-boot-arm:
Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
arm: jadecpu: Readd MACH_TYPE_JADECPU
at91: defined mach-types for otc570 board in board config file
at91: defined mach-types for meesc board in board config file
mx31pdk: Enable D and I caches
ehci-mxc: remove incorrect comment
README: Fix supported i.MX SoC list for CONFIG_MXC_SPI
mx53: Turn off child clocks before reconfigure perclk_root
qong: enable support for compressed images
imx: imx31_phycore.h: fix checkpatch warnings
vision2: Remove unused get_board_rev function
mx53smd: Remove unused get_board_rev function
mx53ard: Remove unused get_board_rev function
mx53evk: Remove unused get_board_rev function
mx53evk: Add RTC support
mx53loco: Remove unused get_board_rev function
mx53evk: Remove unneeded '1' from mx53evk.h
OMAP3: mvblx: Initial support for mvBlueLYNX-X
ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
omap3: mem: Move comments next to definitions
omap3: mem: Clean-up whitespaces
omap3: mem: Define and use common macros
Davinci: ea20: added PREBOOT to configuration
Davinci: ea20: added I2C support
Davinci: ea20: added video support
VIDEO: davinci: add framebuffer to da8xx
ARM: Davinci: added missing registers to hardware.h
Davinci: ea20: add gpios for LCD backlight control
Davinci: ea20: add gpio for keeping power on in board_late_init
Davinci: ea20: Add default U-Boot environment
Davinci: ea20: Add early init to get early output from console
Davinci: ea20: Add NAND support
Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console
Davinci: ea20: set console on UART0
arm, davinci: add cam_enc_4xx support
arm926ejs, davinci: add missing spi defines for dm365
arm926ejs, davinci: add cpuinfo for dm365
arm, davinci: add lowlevel function for dm365 soc
arm, davinci: add header files for dm365
spl, nand: add 4bit HW ecc oob first nand_read_page function
arm, davinci: add support for new spl framework
spl: add option for adding post memory test to the SPL framework
net, davinci_emac: make clock divider in MDIO control register configurable
arm, usb, davinci: make USBPHY_CTL register configurable
usb, davinci: add enable_vbus() weak function
omap3evm: fix errors caused by multiple definitions
omap3evm: Add (quick) configuration for NAND only
omap3evm: Add (quick) configuration for MMC/SD only
omap3evm: move common config options to new file
omap3evm: Prepare to split configuration
omap3evm: Reorder related config options
omap/spl: actually enable the console
davinci_emac: compilation fix, phy is array now
omap3evm: Set environment variable 'ethaddr'
arm, arm926: fix missing symbols in NAND_SPL mode
arm, davinci: Add function lpsc_syncreset()
arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
arm/km: portl2 environment address update to P1B
arm/km: adapt bootcounter evaluation
arm/km: enable jffs2 cmds
arm/km: trigger reconfiguration for the Xilinx FPGA
arm/km: add boardid and hwkey to kernel command line
ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
netspace_v2: enable I2C EEPROM support
netspace_v2: fix SDRAM configuration
armada100: define CONFIG_SYS_CACHELINE_SIZE
pantheon: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: drop empty asm-offsets.s file
arm/km/mgcoge3un: enhance "waitforne" feature
arm/km: add variable waitforne to mgcoge3un
gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared
ARM: dreamplug: fix compilation
ARM: DockStar: fix compilation
ARM: netspace_v2: fix warnings
am335x: Drop board_sysinfo struct
am335x: Temporarily add MACH_TYPE define
misc:pmic:samsung Enable PMIC driver at C210 Universal target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target
smdkv310: use macro for mmc data read function address
smdkv310: use spl framework for mmc spl
SMDKV310: use get_ram_size() to validate dram size
SMDKV310: Initialize board id using CONFIG_MACH_TYPE
ORIGEN : use absolute paths and fix tool naming
ORIGEN : enable device tree support
MX25: tx25: Fix building due to missing MACH_TYPE
mx31: Add board support for HALE TT-01
mx31: add ESD control registers
mx31: define pins and init for UART2 and CSPI3
MX35: add support for flea3 board
MX51: vision2: add MACH_TYPE in config file
vision2: Remove unused header file
mx51evk: Remove unused get_board_rev function
mx51evk: Remove unneeded '1' from mx51evk.h
I2C: Fix mxc_i2c.c problem on imx31_phycore
mx35pdk: Add RTC support
mx51evk: Use GPIO API for configuring the IOMUX
mx51evk: Add RTC support
rtc: Make mc13783-rtc driver generic
qong: remove unneeded IOMUX settings
qong: Use mx31_set_gpr to setup USBH2 pins
mx31: Introduce mx31_set_gpr function
mx31pdk: Add MC13783 PMIC support
qong: remove unneeded "1" from qong.h
misc: pmic: fix regression in pmic_fsl.c (SPI)
mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME
MX35: Drop unnecessary prototypes from imx-regs.h
I2C: added I2C-2 and I2C-3 to MX35
MX35: factorize common assembly code
MX35: add reset cause as provided by other i.MX
MX35: add pins definition for UART3
MX35: added ESDC structure to imx-regs
* 'master' of git://git.denx.de/u-boot-coldfire:
ColdFire: The EB+MCF-EV123 boards config update
ColdFire: Fix the compile issue for M52277
ColdFire:Moving the remaining coldfire boards to boards.cfg
Fix:
scm.c: In function 'config_scoh_cs':
scm.c:400:16: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
vovpn-gw.c: In function 'misc_init_r':
vovpn-gw.c:266:16: warning: variable 'temp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
mpc8266ads.c: In function 'initdram':
mpc8266ads.c:278:9: warning: variable 'spd_size' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
sacsng.c: In function 'initdram':
sacsng.c:180:9: warning: variable 'spd_size' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
Fix:
flash.c: In function 'flash_init':
flash.c:52:19: warning: variable 'size' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Really minimal and local, just good enough to make checkpatch not
complain about the changes in the following commit.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
ids8247.c: In function 'initdram':
ids8247.c:284:14: warning: variable 'lsize' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Fix:
input.c: In function 'hymod_get_ethaddr':
input.c:79:10: warning: variable 'ea' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Murray Jensen <Murray.Jensen@csiro.au>
Fix:
ep82xxm.c: In function 'initdram':
ep82xxm.c:233:16: warning: variable 'ramtmp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
flash.c: In function 'flash_init':
flash.c:81:16: warning: variable 'size' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Oliver Brown <obrown@adventnetworks.com>
Really minimal and local, just good enough to make checkpatch not
complain about the changes in the following commit.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Oliver Brown <obrown@adventnetworks.com>
Fix:
flash.c: In function 'flash_init':
flash.c:295:16: warning: variable 'fip' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Murray Jensen <Murray.Jensen@csiro.au>
Fix:
spi.c: In function 'spi_init_r':
spi.c:279:22: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
spi.c: In function 'spi_xfer':
spi.c:361:22: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
cmd_flash.c:355:32: warning: 'info' may be used uninitialized in this
function [-Wuninitialized]
cmd_flash.c:354:10: warning: 'sect_first' may be used uninitialized in
this function [-Wuninitialized]
cmd_flash.c:354:10: warning: 'sect_last' may be used uninitialized in
this function [-Wuninitialized]
cmd_flash.c: In function 'do_protect':
cmd_flash.c:540:9: warning: 'info' may be used uninitialized in this
function [-Wuninitialized]
cmd_flash.c:538:9: warning: 'sect_first' may be used uninitialized in
this function [-Wuninitialized]
cmd_flash.c:538:9: warning: 'sect_last' may be used uninitialized in
this function [-Wuninitialized]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
rtl8139.c: In function 'rtl8139_probe':
rtl8139.c:256:15: warning: variable 'fullduplex' set but not used
[-Wunused-but-set-variable]
rtl8139.c:256:6: warning: variable 'speed10' set but not used
[-Wunused-but-set-variable]
rtl8139.c: In function 'rtl_transmit':
rtl8139.c:419:16: warning: variable 'txstatus' set but not used
[-Wunused-but-set-variable]
Change code to use new debug macros; also fix the new errors and
warnigns popping up now, like "error: 'to' undeclared" and some
"warning: format '%X' expects argument of type 'unsigned int', but
argument X has type 'long unsigned int'"
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
rtl8169.c: In function 'rtl_init':
rtl8169.c:742:13: warning: variable 'printed_version' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
flash.c: In function 'flash_erase':
flash.c:780:18: warning: variable 'l_sect' set but not used
[-Wunused-but-set-variable]
flash.c:779:11: warning: variable 'addr' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
pcnet.c: In function 'pcnet_probe':
pcnet.c:247:8: warning: variable 'chipname' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
Fix:
flash.c: In function 'flash_erase':
flash.c:409:21: warning: variable 'last' set but not used
[-Wunused-but-set-variable]
flash.c:408:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:669:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data_block':
flash.c:709:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
bat_rw.c: In function 'write_bat':
bat_rw.c:38:6: warning: variable 'batn' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andy Fleming <afleming@gmail.com>
Fix:
i2c.c: In function 'wait_for_bb':
i2c.c:109:16: warning: variable 'temp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This also fixes some GCC 4.6 build warnings like:
i2c.c: In function 'i2c_init':
i2c.c:221:26: warning: variable 'txbd' set but not used
[-Wunused-but-set-variable]
i2c.c:221:19: warning: variable 'rxbd' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Make (mostly) checkpatch clean (don't convert to use I/O accessors
yet, so there will be "Use of volatile is usually wrong" warnings
left. Also accept some other harmless checkpatch warnings.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Fix:
fec.c: In function 'mpc8220_fec_recv':
fec.c:733:8: warning: variable 'frame' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
cmd_i2c.c: In function 'do_i2c_add_bus':
cmd_i2c.c:1212:19: warning: variable 'dev' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Fix:
tqm8272.c: In function 'initdram':
tqm8272.c:462:14: warning: variable 'lsize' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
speed.c: In function 'get_clocks':
speed.c:113:30: warning: variable 'cpmdf' set but not used
[-Wunused-but-set-variable]
speed.c:113:23: warning: variable 'busdf' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
This also fixes a build warning:
main.c: In function 'main_loop':
main.c:311:16: warning: variable 'bootlimit' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
flash.c: In function 'write_word':
flash.c:542:15: warning: variable 'last' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Make (mostly) checkpatch clean (don't convert to use I/O accessors
yet, so there will be "Use of volatile is usually wrong" warnings
left.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
svm_sc8xx.c: In function 'checkboard':
svm_sc8xx.c:83:6: warning: variable 'board_type' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
The RBC823 has only one NOR flash bank. Remove all code trying to
deal with a second bank. This also fixes a number of GCC 4.6 build
warnings:
flash.c: In function 'flash_init':
flash.c:62:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:63:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:66:12: warning: array subscript is above array bounds
[-Warray-bounds]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Make (mostly) checkpatch clean (don't convert to use I/O accessors
yet, so there will be "Use of volatile is usually wrong" warnings
left.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
fads.c: In function 'initdram':
fads.c:606:7: warning: variable 'base' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
mbx8xx.c: In function 'mbx_init':
mbx8xx.c:127:15: warning: variable 'refclock' set but not used
[-Wunused-but-set-variable]
mbx8xx.c: In function 'board_get_cpufreq':
mbx8xx.c:231:2: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
mbx8xx.c: In function 'get_reffreq':
mbx8xx.c:242:2: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
spi.c: In function 'spi_init_f':
spi.c:144:21: warning: variable 'iop' set but not used
[-Wunused-but-set-variable]
spi.c:142:22: warning: variable 'cpi' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
net.c: In function 'CDPHandler':
net.c:1083:8: warning: variable 'applid' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
The GENIETV has only one NOR flash bank. Remove all code trying to
deal with a second bank. This also fixes a number of GCC 4.6 build
warnings:
flash.c:65:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:66:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:69:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:183:2: warning: format '%x' expects argument of type 'unsigned
int', but argument 2 has type '
Signed-off-by: Wolfgang Denk <wd@denx.de>
Make (mostly) checkpatch clean (don't convert to use I/O accessors yet,
so there will be "Use of volatile is usually wrong" warnings left.
Signed-off-by: Wolfgang Denk <wd@denx.de>
